A nonlinear model of anti-backlash gear with time-varying friction and mesh stiffness was proposed for the further study on dynamic characteristics of anti-backlash gear. In order to improve the model precision, appli...A nonlinear model of anti-backlash gear with time-varying friction and mesh stiffness was proposed for the further study on dynamic characteristics of anti-backlash gear. In order to improve the model precision, applied force analysis was completed in detail, and single or double tooth meshing states of two gear pairs at any timing were determined according to the meshing characteristic of anti-backlash gear. The influences of friction and variations of damping ratio on dynamic transmission error were analyzed finally by numerical calculation and the results show that anti-backlash gear can increase the composite mesh stiffness comparing with the mesh stiffness of the normal gear pair. At the pitch points where the frictions change their signs, additional impulsive effects are observed. The width of impulsive in the same value of center frequency is wider than that without friction, and the amplitude is lower. When gear pairs mesh in and out, damping can reduce the vibration and impact.展开更多
A novel specific type of worm drive, so-called end face engagement worm gear（EFEWD）, is originally presented to minimize or overcome the gear backlash. Different factors, including the three different types, contact...A novel specific type of worm drive, so-called end face engagement worm gear（EFEWD）, is originally presented to minimize or overcome the gear backlash. Different factors, including the three different types, contact curves, tooth profile, lubrication angle and the induced normal curvature are taken into account to investigate the meshing characteristics and create the profile of a novel specific type of worm drive through mathematical models and theoretical analysis. The tooth of the worm wheel is very specific with the sine-shaped tooth which is located at the alveolus of the worm and the tooth profile of a worm is generated by the meshing movement of the worm wheel with the sine-shaped tooth, but just the end face of the worm（with three different typical meshing types） is adapted to meshing, and therefore an extraordinary manufacturing methods is used to generate the profile of the end face engagement worm. The research results indicates that the bearing contacts of the generated conjugate hourglass worm gear set are in line contacts, with certain advantages of no-backlash, high precision and high operating efficiency over other gears and gear systems besides the end face engagement worm gear drive may improve bearing contact, reduce the level of transmission errors and lessen the sensitivity to errors of alignment. Also, the end face engagement worm can be easily made with superior meshing and lubrication performance compared with the conventional techniques. In particular, the meshing and lubrication performance of the end face engagement worm gear by using the end face to meshing can be increased over 10% and 7%, respectively. This investigate is expect to provide a new insight on the design of the future no-backlash worm drive for industry.展开更多
Over the past decade,the electric vehicle industry of China has developed rapidly,reaching one of the highest technological levels in the world.Nevertheless,most electric buses currently serve urban areas,being unsuit...Over the past decade,the electric vehicle industry of China has developed rapidly,reaching one of the highest technological levels in the world.Nevertheless,most electric buses currently serve urban areas,being unsuitable for all-climate operations.In response to the objective of massively adopting electric vehicles for transportation during all the events of the 2022 Beijing Winter Olympics,a dual-motor coaxial propulsion system for all-climate electric vehicles is proposed.The system aims to meet operating requirements such as high speed and adaptability to mountainous roads under severely cold environments.The system provides three operating modes,whose characteristics are analyzed under different conditions.In addition,dual-motor collaborative control strategy with collaborative gearshift and collaborative power distribution is proposed to eliminate power interruption during gearshift process and achieve intelligent power distribution,thus improving the gearshift quality and reducing energy consumption.Finally,gear position calibration for all-climate operation and proper gearshift is introduced.Experimental results demonstrate the advantages of the proposed dual-motor coaxial propulsion system regard-ing gearshift compared with the conventional single-motor automatic transmission.展开更多
基金Project(51175505)supported by the National Natural Science Foundation of China
文摘A nonlinear model of anti-backlash gear with time-varying friction and mesh stiffness was proposed for the further study on dynamic characteristics of anti-backlash gear. In order to improve the model precision, applied force analysis was completed in detail, and single or double tooth meshing states of two gear pairs at any timing were determined according to the meshing characteristic of anti-backlash gear. The influences of friction and variations of damping ratio on dynamic transmission error were analyzed finally by numerical calculation and the results show that anti-backlash gear can increase the composite mesh stiffness comparing with the mesh stiffness of the normal gear pair. At the pitch points where the frictions change their signs, additional impulsive effects are observed. The width of impulsive in the same value of center frequency is wider than that without friction, and the amplitude is lower. When gear pairs mesh in and out, damping can reduce the vibration and impact.
基金Supported by National Natural Science Foundation of China(Grant No.51305356)Spring Sunshine Plan of Ministry of Education of China(Grant No.14202505)Talent Introduction of Xihua University,China(Grant No.Z1220217)
文摘A novel specific type of worm drive, so-called end face engagement worm gear（EFEWD）, is originally presented to minimize or overcome the gear backlash. Different factors, including the three different types, contact curves, tooth profile, lubrication angle and the induced normal curvature are taken into account to investigate the meshing characteristics and create the profile of a novel specific type of worm drive through mathematical models and theoretical analysis. The tooth of the worm wheel is very specific with the sine-shaped tooth which is located at the alveolus of the worm and the tooth profile of a worm is generated by the meshing movement of the worm wheel with the sine-shaped tooth, but just the end face of the worm（with three different typical meshing types） is adapted to meshing, and therefore an extraordinary manufacturing methods is used to generate the profile of the end face engagement worm. The research results indicates that the bearing contacts of the generated conjugate hourglass worm gear set are in line contacts, with certain advantages of no-backlash, high precision and high operating efficiency over other gears and gear systems besides the end face engagement worm gear drive may improve bearing contact, reduce the level of transmission errors and lessen the sensitivity to errors of alignment. Also, the end face engagement worm can be easily made with superior meshing and lubrication performance compared with the conventional techniques. In particular, the meshing and lubrication performance of the end face engagement worm gear by using the end face to meshing can be increased over 10% and 7%, respectively. This investigate is expect to provide a new insight on the design of the future no-backlash worm drive for industry.
基金This work was supported in part by the National Natural Science Foundation of China under Grant 51975049in part by the National Key Technology Research and Development Program of China under Grant 2017YFB0103801.
文摘Over the past decade,the electric vehicle industry of China has developed rapidly,reaching one of the highest technological levels in the world.Nevertheless,most electric buses currently serve urban areas,being unsuitable for all-climate operations.In response to the objective of massively adopting electric vehicles for transportation during all the events of the 2022 Beijing Winter Olympics,a dual-motor coaxial propulsion system for all-climate electric vehicles is proposed.The system aims to meet operating requirements such as high speed and adaptability to mountainous roads under severely cold environments.The system provides three operating modes,whose characteristics are analyzed under different conditions.In addition,dual-motor collaborative control strategy with collaborative gearshift and collaborative power distribution is proposed to eliminate power interruption during gearshift process and achieve intelligent power distribution,thus improving the gearshift quality and reducing energy consumption.Finally,gear position calibration for all-climate operation and proper gearshift is introduced.Experimental results demonstrate the advantages of the proposed dual-motor coaxial propulsion system regard-ing gearshift compared with the conventional single-motor automatic transmission.
