Tailoring Carbon Distribution inα/γPhase of Ductile Iron and Its Effects on Thermal Conductivity

The effects of carbon distribution on the microstructure and thermal conductivity of ductile iron were investigated in the present study.The microstructure of as-cast and quenched ductile iron were characterized by OM and SEM.Results showed that the microstructure of as-cast ductile iron was composed of spheroidal graphite,ferrite with the volume of 80%,and a small amount of pearlite,and quenched ductile iron was composed of spheroidal graphite,coarse/fine acicular martensite(α_(M)phase)and high-carbon retained austenite(γphase).The volume fraction of retained austensite and its carbon content for direct quenched ductile iron and tepmered ductile iron were quantitatively analysed by XRD.Results revealed that carbon atoms diffused fromα_(M)phase toγphase during tempering at low temperatures,which resulted in carbon content in retainedγphase increasing from 1.2 wt%for the direct quenched sample to about 1.9 wt%for the tempered samples.Consequently,the lattice distortion was significantly reduced and gave rise to an increase of thermal conductivity for ductile iron.

A Bidimensional Finite Element Study of Crack Propagation in Austempered Ductile Iron

Austempered ductile iron(ADI)is composed of an ausferritic matrix with graphite nodules and has a wide range of applications because of its high mechanical strength,fatigue resistance,and wear resistance compared to other cast irons.The amount and size of the nodules can be controlled by the chemical composition and austenitizing temperature.As the nodules have lower stiffness than the matrix and can act as stress concentrators,they influence crack propagation.However,the crack propagation mechanism in ADI is not yet fully understood.In this study,we describe a numerical investigation of crack propagation in ADIs subjected to cyclic loading.The numerical model used to calculate the stress intensity factors in the material under the given conditions is built with the aid of Abaqus commercial finite element code.The crack propagation routine,which is based on the Paris law,is implemented in Python.The results of the simulation show that the presence of a nodule generates a shear load on the crack tip.Consequently,even under uniaxial tensile loading,the presence of the nodule yields a non-zero stress intensity factor in mode II,resulting in a deviation in the crack propagation path.This is the primary factor responsible for changing the crack propagation direction towards the nodule.Modifying the parameters,for example,increasing the nodule size or decreasing the distance between the nodule and crack tip,can intensify this effect.In simulations comparing two different ADIs with the same graphite fraction area,the crack in the material with more nodules reaches another nodule in a shorter propagation time(or shorter number of cycles).This suggests that the high fatigue resistance observed in ADIs may be correlated with the number of nodules intercepted by a crack and the additional energy required to nucleate new cracks.In summary,these findings contribute to a better understanding of crack propagation in ADIs,provide insights into the relationship between the presence of nodules and the fatigue resistance of these materials,and support studies that associate the increased fatigue resistance with a higher number of graphite nodules.These results can also help justify the enhanced fatigue resistance of ADIs when compared to other cast irons.

A study on controlled cooling process for making bainitic ductile iron

In the present research, TTT curve of bainitic ductile iron under the condition of controlled cooling was generated. The cooling rate of grinding ball and its temperature distribution were also measured at the same time. It can be concluded that the bainitic zone of TTT curve is separated from the pearlitic zone. As compared to the water-quenching condition, more even cooling rate and temperature distribution can be achieved in the controlled cooling process. The controlled cooling can keep away from pearlitic zone in the high temperature cooling stage and produce similar results to the process of traditional isothermal cooling with a low cooling rate in the low temperature cooling stage.

Effect of austempering parameters on microstructure and mechanical properties of horizontal continuous casting ductile iron dense bars

In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters （i.e. austenitizing temperature and time, and austempering temperature and time） on microstructure and mechanical properties of LZQT500-7 ductile iron dense bars with 172 mm in diameter which were produced by horizontal continuous casting （HCC）. The results show that the major factors influencing the hardness of austempered ductile iron （ADI） are austenitizing temperature and austempering temperature. The fraction of retained austenite increases as the austenitizing and austempering temperatures increase. When austenitizing temperature is low, acicular ferrite and retained austenite can be efifciently obtained by appropriately extending the austenitizing time. The proper austmepering time could ensure enough stability of retained austenite and prevent high carbon austenite decomposition. The optimal mechanical properties of ADI can be achieved with the fol owing process parameters： austenitizing temperature and time are 866 ＆#176;C and 135 min, and austempering temperature and time are 279 ＆#176;C and 135 min, respectively. The microstructure of ADI under the optimal austempering process consists of ifne acicular ferrite and a smal amount of retained austenite, and the hardness, tensile strength, yield strength, elongation and impact toughness of the bars are HBW 476, 1670 MPa, 1428 MPa, 2.93%and 25.7 J, respectively.

Solution strengthened ferritic ductile iron ISO 1083/JS/500-10 provides superior consistent properties in hydraulic rotators

Consistent mechanical and machining properties are essential in many applications where ductile irons offer the most cost-effective way to produce structural parts.In the production of hydraulic rotators,dimensional tolerances are typically 20μm to obtain designated performance.For castings where intermediate strength and ductility is required,it is common knowledge that conventional ferritic-pearlitic ductile irons such as ISO 1083/500-7 show large hardness variations.These are mainly caused by the notoriously varying pearlite content,both at different locations within a part and between parts in the same or different batches.Cooling rate variations due to different wall thickness and position in the molding box,as well as varying amounts of pearlite-stabilizing elements,all contribute to detrimental hardness variations.The obvious remedy is to avoid pearlite formation,and instead obtain the necessary mechanical properties by solution strengthening of the ferritic matrix by increasing silicon content to 3.7wt%-3.8wt%.The Swedish development in this field 1998 resulted in a national standardization as SS 140725,followed in 2004 by ISO 1083/ JS/500-10.Indexator AB decided 2005 to specify JS/500-10 for all new ductile iron parts and to convert all existing parts.Improvements include reduction by 75%in hardness variations and increase by 30%in cutting tool life,combined with consistently better mechanical properties.

Low temperature impact strength of heavy section ductile iron castings:effects of microstructure and chemical composition

A foundry research project has been recently initiated at RTIT in order to better understand the fabrication of as-cast heavy section DI parts meeting high impact energy requirements at low temperatures.The experimental castings have the following dimensions 180 mm x 180 mm x 190 mm.The achieved as-cast Charpy impact strengths were as follows:17 J (RT),16 J (-20℃) and 11 J (-40℃).The foundry process,the chemical composition and the microstructure of this experimental casting are compared to the ones of various examples in order to show the detrimental effects of residual elements,microshrinkage and microcarbide on the impact properties.Finally,quality index empirical models (based on casting chemical compositions) are used to analyse the impact tests results.This paper illustrates that an adequate nodule count can contribute to reducing the detrimental effects of the residual elements and microsegregation.

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

The wear resistances of austempered ductile iron （ADI） were improved through intxoduction of a new phase （carbide） into the ma- txix by addition of chromium. In the present investigation, low-caxbon-equivalent ductile iron （LCEDI） （CE = 3.06%, and CE represents cax- bon-equivalent） with 2.42% chromium was selected. LCEDI was austeintized at two difl＇erent temperatures （900 and 975~C） a^ld soaked for 1 h and then quenched in a salt bath at 325~C for 0 to 10 h. Samples were analyzed using optical microscopy and X-ray diffraction. Wear tests were carded out on a pin-on-disk-type machine. The efl＇ect of austenization temperature on the wear resistance, impact strength, and the mi- crostructure was evaluated. A stxucture-property correlation based on the observations is established.

Performance of heavy ductile iron castings for windmills

The main objective of the present paper is to review the specific characteristics and performance obtaining conditions of heavy ductile iron(DI) castings,typically applied in windmills industry,such as hubs and rotor housings.The requirements for high impact properties in DI at low temperatures are part of the ENGJS-400-18U-LT(SRN 1563) commonly referred to as GGG 40.3(DIN 1693).Pearlitic in-uence factor(Px) and antinodularising action factor(K1) were found to have an important in-uence on the structure and mechanical properties,as did Mn and P content,rare earth(RE) addition and inoculation power.The presence of high purity pig iron in the charge is extremely beneficial,not only to control the complex factors Px and K1,but also to improve the 'metallurgical quality' of the iron melt.A correlation of C and Si limits with section modulus is very important to limit graphite nodule flotation.Chunky and surface-degenerated graphite are the most controlled graphite morphologies in windmills castings.The paper concluded on the optimum iron chemistry and melting procedure,Mg-alloys and inoculants peculiar systems,as well as on the practical solutions to limit graphite degeneration and to ensure castings of the highest integrity,typically for this field.

Influencing factors on as-cast and heat treated 400-18 ductile iron grade characteristics

As-cast and heat-treated 400-18 ductile iron （DI） grade was obtained in different foundry conditions, as metallic charge, Mg-treatment alloy and inoculation. It was found that the Pearlitic Influence Factor （P） and Anti- nodulizing Complex Factor （K1） have an important influence on property of DI, depending on the Mn and P level, the metallurgical quality of iron melt, rare earth （RE） and inoculation. It was also found that the influence of Mn is depended on the phosphorus and residual elements level in ductile iron. Less than 0.03%P and 0.2%Mn and P〈2.0 are the basic conditions to obtain as-cast ferritic structure. At the same lower level of Mn and P, the increasing of residual elements （P〉2.0） determines presence of pearlite in as-cast structure, while ferrite structure is obtained after a short annealing heat treatment. Lower level of phosphorus （P〈0.025%） and residual elements （Px〈2.0） allow to use relative high Mn content （0.32%-0.38%）, in condition of ferritic structure, including in as-cast state. High P （0.04%- 0.045%） and Mn （0.25%-0.35%） content stabilized peadite, especially at lower level of residual elements （P 〈2.0）. Antinodulizing action of elements was counteracted up to K1=2.0 level, by RE included in Mg-treatment alloy, which are beneficial for K1〈1.2 and compulsory for K1〉1.2. Si has a significant influence on the mechanical properties of heat treated ductile irons： an important decreasing of elongation level and a moderate increasing of yield and tensile strength and their ratio in 150-170 HB typical hardness field. A typical final chemical composition for as-cast 400-18 ductile iron could include 3.5%-3.7%C, 2.4%-2.5%Si, max.0.18%Mn, max.0.025%P, max.0.01%S, 0.04%-0.05%Mg for Px〈1.5 and K1〈1.1. High purity pig iron, RE-bearing FeSiMg and powerful inoculant are also recommended.

Precipitation and evolution of nodular graphite during solidification process of ductile iron

The quantity and morphology of spheroidal graphite have an important effect on the properties of ductile iron, and the characteristics of spheroidal graphite are determined by the solidification process. The aim of this work is to explore the precipitation and evolution of graphite nodules in hypoeutectic, eutectic, and hypereutectic ductile irons by thermal analysis, liquid quenching and metallographic technique. Results show that hypoeutectic ductile iron has the longest solidification time and the lowest eutectic temperature;eutectic ductile iron has the shortest solidification time;hypereutectic ductile iron has the highest eutectic temperature. After solidification is completed, hypoeutectic ductile iron has the lowest nodule count, nodularity and graphite fraction;eutectic ductile iron has the highest nodule count, nodularity and the smallest nodule diameter;hypereutectic has the highest nodule diameter and graphite fraction. The nucleation and growth of graphite nodules in hypereutectic ductile iron starts before bulk eutectic crystallization stage, however, the precipitation and evolution of graphite nodules of hypoeutectic and eutectic ductile irons mainly occur in the eutectic crystallization stage. The graphite precipitated in eutectic crystallization of hypoeutectic, eutectic, and hypereutectic ductile irons, are 61%, 68% and 43% of total graphite volume fraction, respectively. Simultaneously, there are plenty of austenite dendrites in hypoeutectic and hypereutectic ductile irons, which are prone to shrinkage defects. Therefore, the eutectic ductile iron has the smallest shrinkage tendency.

Production of carbide-free thin ductile iron castings

The fast cooling rate of thin ductile iron castings requires special consideration to produce carbide-free castings. Extraordinary care was taken to select the charge to produce castings of 100-mm long round bars with 16-mm diameter. The castings show the presence of carbides in the bars. Seven melts were made with different temperatures and with different compositions to get rid of carbides. After chemical analyses,it was found that the extra purity of the charge with less than 0.008wt% sulfur in the castings was the cause of carbides. To remove the carbides from the castings,sulfur should be added to the charge.

Development of thermal simulation system for heavy section ductile iron solidification

A new reliable thermal simulation system for studying solidification of heavy section ductile iron has been developed using computer feedback control and artificial intelligent methods. Results of idle test indicate that the temperature in the system responses exactly to the inputted control data and the temperature control error is less than ±0.5%. It is convenient to simulate solidification of heavy section ductile iron using this new system. Results of thermal simulation experiments show that the differences in nodularity and number of graphite nodule per unit area in the thermal simulation specimen and the actual heavy section block is less than 5% and 10%, respectively.

Influence of cooling rate and antimony addition content on graphite morphology and mechanical properties of a ductile iron

Cooling rate and inoculation practice can greatly affect the graphite morphology of ductile irons. In the present research, the effects of the cooling rate and antimony addition on the graphite morphology and mechanical properties of ductile irons have been studied. Three ductile iron castings were prepared through solidification under cooling conditions S （slow）, M （medium） and F （fast）. The cooling rates around the equilibrium eutectic temperature （1,150 ℃） for these cooling conditions （S, M and F） were set at 0.21 ℃.min1, 0.32℃.min1 and 0.37℃-min-1, respectively. In addition, four ductile iron castings were prepared by adding 0.01%, 0.02%, 0.03% and 0.04% （by weight） antimony, respectively under the slow cooling condition. The results show that the nodularity index, tensile strength and hardness of the ductile iron castings without antimony addition are all improved with the increase of cooling rate, while the ductile iron casting solidified under the medium cooling rate possesses the largest number of graphite nodules. Furthermore, for the four antimony containing castings, the graphite morphology and tensile strength are also improved by the antimony additions, and the effect of antimony addition is intensified when the addition increases from 0.01% to 0.03%. Moreover, the rare earth elements （REE）/antimony ratio of 2 appears to be the most effective for fine nodular graphite formation in ductile iron.

Low temperature impact toughness and fracture mechanism of cast QT400-18L ductile iron with diferent Ni additions

Different contents of Ni(0.3wt.%to 1.2wt.%)were added to the QT400-18L ductile iron to investigate the effect of Ni addition on the impact toughness of cast ductile irons at low temperatures.The impact toughnesses of the samples at room and low temperatures were tested.The microstructures and fractographs were observed.Results show that with the increase of Ni addition there is a general trend of refinement of the ferrite matrix while the nodule density shows no obvious change.When the Ni content is 0.7wt.%,the matrix structure is the refined ferrite with a very small fraction(about 2%)of pearlite near the eutectic cell boundaries.When the Ni content is further increased,the fraction of pearlite increases significantly and reaches more than 5%when 1.2wt.%Ni is added.The impact toughness at room temperature increases as the content of Ni increases from 0.3 wt.%to 0.7 wt.%,but decreases as the Ni content further increases to 1.2wt.%due to the increase of pearlite fraction.The maximum value of the impact work is 18.5 J at room temperature with 0.7wt.%Ni addition.The average value of the impact work is still more than 13 J even at-30℃.In addition,the fracture mechanism changes from ductile manner to brittleness as the testing temperature decreases from 20℃to-60℃.

Effect of alloying elements on austempered ductile iron(ADI) properties and its process:Review

Austempered ductile iron(ADI) parts have a unique combination of high strength and toughness with excellent design flexibility and low cost. These excellent properties are directly related to its microstructure called "ausferrite" that is the result of austempering heat treatment applied to ductile irons. Alloying elements increase ADI austemperability and change speeds of austempering reactions. Thus, they can affect ADI resultant microstructure and mechanical properties. In this paper, the effects of alloying elements on ADI mechanical properties, microstructural changes, two-stage austempering reactions, processing windows, austemperability, and other aspects are reviewed.

Effects of forced cooling on mechanical properties and fracture behavior of heavy section ductile iron

To develop materials suitable for spent-nuclear-fuel containers, the effect of forced cooling on mechanical properties and fracture toughness of heavy section ductile iron was investigated. Two cubic castings with different cooling processes were prepared: casting A was prepared in a totally sand mold, and casting B was prepared in a sand mold with two chilling blocks placed on the left and right sides of the mold. Three positions in each casting with different solidification cooling rates were chosen. In-situ SEM tensile experiment was used to observe the dynamic tensile process. Fracture analysis was conducted to study the influence of vermicular and slightly irregular spheroidal graphite on the fracture behavior of heavy section ductile iron. Results show that the tensile strength, elongation, impact toughness and fracture toughness at different positions of the two castings all decrease with decreasing cooling rate. With the increase of solidification time, the fracture mechanism of conventional casting A changes from ductile fracture to brittle fracture, and that of casting B with forced cooling changes from ductile fracture to a mixture of ductile-brittle fracture.

Effect of Lanthanum on Nodule Count and Nodularity of Ductile Iron

The present study aims at finding out the effect of the addition of a single rare earth element, that is, lanthanum on the nodularity and nodule count of ductile iron under controlled conditions. For this purpose, four melts with different compositions were made, using a 28 kg inductotherm medium frequency induction furnace. The temperature was carefully maintained between 1400 and 1450 ℃ for these heats. A good quality charge consisting of Sorel metal, ferrosilicon, Swedish iron, ferrosilicon magnesium, and ferrosilicon lanthanum was used for the production of melts. A vertically parted sand mould was used for casting of 10 test bars made from local silica sand. Standard coin samples were chill-cast to conduct chemical analysis of the ductile iron. Mierostructure study of the samples was conducted using a Leica optical microscope. Nodule count and nodularity of the samples were carried out using an image analyzer. The results obtained indicated that with the increased addition of lanthanum the nodule count of ductile iron increased, thus making it evident that it played a significant role in increasing the mechanical properties. The highest nodule count of 467 was obtained with the addition of 0.03% lanthanum. However, the effect of lanthanum on nodularity was negligible with nodularity ranging from 81% to 83 %.

Effect of shrinkage porosity on mechanical properties of ferritic ductile iron

Casting defects could largely affect the mechanical properties of casting products. A number of test pieces made of ductile iron (EN-GJS-400-18-LT) with different levels of shrinkage porosity were prepared and then tensile and fatigue tests were performed to investigate the impact of shrinkage porosity on their mechanical properties. The results showed that the tensile strength decreases linearly with increasing of the shrinkage porosity. The tensile elongation decreases sharply with the increase of the shrinkage porosity mainly due to the non-uniform plastic deformation. The fatigue life also dramatically declines with increasing of the porosity and follows a power law relationship with the area percentage of porosity. The existence of the shrinkage porosity made the fatigue fracture complex. The shrinkage pores, especially those close to the surface usually became the crack initiation sites. For test pieces with less porosity, the fatigue fracture was clearly composed of crack initiation, propagation, and overloading. While for samples with high level of porosity, multiple crack initiation sites were observed.

Effect of sub-zero cooling on microstructure and mechanical properties of a low alloyed austempered ductile iron

The effect of sub-zero cooling on microstructure and mechanical properties of a low alloyed austempered ductile iron has been investigated. Austempering of samples was performed at 325℃and 400℃after austenitizing at 875℃and 950℃. The sub-zero treatments were carried out by cooling down the samples to -30℃, -70℃and -196℃. The changes in volume fraction of austenite and mechanical properties were determined after cooling to each temperature. The austenite volume fraction of samples which were austenitized at 875℃and austempered at 325℃remained unchanged, whilst it reduced in samples austenitized at 950℃and 875℃for austempering temperature of 400℃. In these specimens, some austenite transformed to martensite after subzero cooling. Mechanical property measurements showed a slight increase in strength and hardness and decrease in elongation and toughness due to this transformation behavior.

Effect of shot peening process on fatigue behavior of an alloyed austempered ductile iron

Shot peening is one of the most common surface treatments to improve the fatigue behavior of metallic parts. In this study the effect of shot peening process on the fatigue behavior of an alloyed austempered ductile iron (ADI) has been studied. Austempering heat treatment consisted of austenitizing at 875℃ for 90 min followed by austempering at three different temperatures of 320, 365 and 400℃. Rotating-bending fatigue test was carried out on samples after shot peening by 0.4-0.6 mm shots. XRD and SEM analysis, micro hardness and roughness tests were carried out to study the fatigue behavior of the samples. Results indicate that the fatigue strengths of samples austempered at 320, 365 and 400℃ are increased by 27.3%, 33.3% and 48.4%, respectively, after shot peening process.