Release characteristics and stabilization of heavy metals in antimony tailings in Yunnan Province,China

The pollution caused by the mining and smelting of heavy metals is becoming an increasingly severe environmental problem.In this study,the environmental risks of mine tailings were explored using typical antimony tailings(the depth of the sample taken from the ground to the deepest position of 120 cm)from the Zuoxiguo mine in Yunnan Province,Southwest China.The tailings were examined to explore the geological background,distribution characteristics,and release characteristics of heavy metals.Additionally,stabilizer treatments for heavy metals were investigated in consideration of waste treatment.The results showed that the contents of Sb and As(8.93×103 and 425 mg/kg,respectively)in the tailings were considerably higher than the local soil background values,suggesting that these metals pose a considerable threat to the surrounding environment.The geological background values of Cr,Cd,Pb,Cu,and Zn were relatively low.The results of static release showed that Sb,As,Cd,and Cr leached from the tailings more easily than Cu,Zn,and Pb under acidic conditions(pH=2.98).Geo-accumulation indices and potential ecological risk indices showed that Sb,As,Cd,and Pb were highly enriched in the tailings,whereas Cu,Cr,and Zn contents were relatively low.The single factor ecological risk index of the mining area showed that Sb and As are high ecological risk factors,whereas Cr,Cu,Zn,Cd,and Pb are not.The results of the orthogonal test results showed that by adding 15.0%(m/m)fly ash and 15.0%(m/m)zeolite powder to the quicklime and curing for 28 d,a significant stabilization effect was observed for Sb,As,and Pb.This study helps determine the priority control components for characteristic heavy metals in antimony tailings,and provides valuable insights regarding the formulation of appropriate mitigation strategies.

A comparative study on kinetics and dynamics of two dump truck lifting mechanisms using MATLAB simscape

In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are established using MATLAB Simscape to analyze their kinetics and dynamics in the lifting and holding stages.The simulation findings are compared to the analytical calculation results in the steady state,and both methods show good agreement.In the early lifting stage,Model 1 produces greater force and discharges goods in the container faster than Model 2.Meanwhile,Model 2 reaches a higher force and ejects goods from the container cleaner than its counterpart at the end lifting stage.The established simulation models can consider the effects of dynamic loads due to inertial moments and forces generated during the system operation.It is crucial in studying,designing,and optimizing the structure of hydraulic-mechanical systems.

Shear resistance characteristics and influencing factors of root-soil composite on an alpine metal mine dump slope with different recovery periods

Artificial vegetation restoration is the main measure for vegetation restoration and soil and water conservation in alpine mine dumps on the Qinghai-Tibet Plateau,China.However,there are few reports on the dynamic changes and the influencing factors of the soil reinforcement effect of plant species after artificial vegetation restoration under different recovery periods.We selected dump areas of the Delni Copper Mine in Qinghai Province,China to study the relationship between the shear strength and the peak displacement of the root-soil composite on the slope during the recovery period,and the influence of the root traits and soil physical properties on the shear resistance characteristics of the root-soil composite via in situ direct shear tests.The results indicate that the shear strength and peak displacement of the rooted soil initially decreased and then increased with the increase of the recovery period.The shear strength of the rooted soil and the recovery period exhibited a quadratic function relationship.There is no significant function relationship between the peak displacement and the recovery period.Significant positive correlations(P<0.05)exists between the shear strength of the root-soil composite and the root biomass density,root volume density,and root area ratio,and they show significant linear correlations(P<0.05).There are no significant correlations(P>0.05)between the shear strength of the root-soil composite and the root length density,and the root volume ratio of the coarse roots to the fine roots.A significant negative linear correlation(P<0.05)exists between the peak displacement of the rooted soil and the coarse-grain content,but no significant correlations(P>0.05)with the root traits,other soil physical property indices(the moisture content and dry density of the soil),and slope gradient.The coarse-grain content is the main factor controlling the peak displacement of the rooted soil.

Rainfall-triggered waste dump instability analysis based on surface 3D deformation in physical model test

Landslide is the second largest natural disaster after earthquake. It is of significance to study the evolution laws and failure mechanism of landslides based on its surface 3D deformation information. Based on the rainfall-triggered waste dump instability model test, we studied the failure mechanisms of the waste dump by integrating surface deformation and internal slope stress and proposed novel parameters for identifying landslide stability. We developed a noncontact measurement device, which can obtain millimeter-level 3D deformation data for surface scene in physical model test;Then we developed the similar materials and established a test model for a waste dump. Based on the failure characteristics of slope surface, internal stress of slope body and displacement contours during the whole process, we divided the slope instability process in model test into four stages: rainfall infiltration and surface erosion, shallow sliding, deep sliding, and overall instability. Based on the obtained surface deformation data, we calculated the volume change during slope instability process and compared it with the point displacement on slope surface. The results showed that the volume change can not only reflect the slow-ultra acceleration process of slope failure, but also fully reflect the above four stages and reduce the fluctuations caused by random factors. Finally, this paper proposed two stability identification parameters: the volume change rate above the slip surface and the relative velocity of volume change rate. According to the calculation of these two parameters in model test, they can be used for study the deformation and failure mechanism of slope stability.

A Predictive Energy Management Strategies for Mining Dump Trucks

The plug-in hybrid vehicles(PHEV)technology can effectively address the issues of poor dynamics and higher energy consumption commonly found in traditional mining dump trucks.Meanwhile,plug-in hybrid electric trucks can achieve excellent fuel economy through efficient energy management strategies(EMS).Therefore,a series hybrid system is constructed based on a 100-ton mining dump truck in this paper.And inspired by the dynamic programming(DP)algorithm,a predictive equivalent consumption minimization strategy(P-ECMS)based on the DP optimization result is proposed.Based on the optimal control manifold and the SOC reference trajectory obtained by the DP algorithm,the P-ECMS strategy performs real-time stage parameter optimization to obtain the optimal equivalent factor(EF).Finally,applying the equivalent consumption minimization strategy(ECMS)realizes real-time control.The simulation results show that the equivalent fuel consumption of the P-ECMS strategy under the experimentally collected mining cycle conditions is 150.8 L/100 km,which is 10.9%less than that of the common CDCS strategy(169.3 L/100 km),and achieves 99.47%of the fuel saving effect of the DP strategy(150 L/100 km).

Innuendoes of Sterilisation Drilling in Surface Mining Operations—A Case Study

Surface mining operations play a crucial role in meeting the world’s increasing demand for mineral resources for the advancement of technology and debauched expansion of economies. The search for and exploitation of these mineral resources are therefore important for the sustainability of the mineral extraction industry. To this end, efficient mine planning must incorporate sterilisation drilling and effective waste rock management principles in the search and exploitation of these minerals. In this article, sterilisation drilling is being reviewed vis-a-vis the establishment of waste and tailings dump locations, backfilling of open pit excavations and mine closure giving critical attention to the minerals and mining laws of Ghana. Subsequently, a detailed case study of a surface mining operation that successfully incorporated sterilisation drilling in determining waste dump location in its mine planning process has been presented in this study. The findings indicate that the proposed waste dump location could present a potential mining prospect in the future based on enhanced milling capacity/technology and improved mineral commodity price;underscoring the significance of sterilization drilling in the sustainability of the mining industry.

Modelling Impact of Dredging and Dumping in Ebb-Flood Channel Systems

For a channel-shoal system in a funnel-shaped basin the impact of dredging and dumping is investigated using a complex process-based model. First, the residual flow and sediment transport circulations are analysed for the channel-shoal pattern, which has emerged after a longterm model simulation. Results are compared to the Western Scheldt estuary, which forms the inspiration for this study. Subsequently, different dredge and dump scenarios are modelled, according to a conceptual model, in which ebb- and flood-channels and enclosed shoals form morphodynamic units (cells) with their own sediment circulation. Model results show that dumping sediment in a channel further reduces the channel depth and induces erosion in the opposite channel, which enhances tilting of the cross-section of the cell and eventually can lead to the degeneration of a multiple channel system into a single channel. The impact of different dredging and dumping cases agrees with results from a stability analysis. This means that this type of model applied to a realistic geometry can potentially be used for better prediction of the impact of human interventions.

Impact of open dumping of municipal solid waste on soil properties in mountainous region

This paper presents the effect of open dumping of municipal solid waste(MSW) on soil characteristics in the mountainous region of Himachal Pradesh, India. The solid waste of dumpsite contains various complex characteristics with organic fractions of the highest proportions. As leachate percolates into the soil, it migrates contaminants into the soil and affects soil stability and strength. The study includes the geotechnical investigation of dump soil characteristics and its comparison with the natural soil samples taken from outside the proximity of dumpsites. The geochemical analysis of dumpsite soil samples was also carried out by scanning electron microscopy(SEM) and energy dispersive X-ray spectroscopy(EDS).Visual inspection revealed that the MSW consists of high fraction of organics, followed by paper. The soil samples were collected from five trial pits in the dumpsites at depths of 0.5 m, 1 m and 1.5 m. Then the collected soil samples were subjected to specific gravity test, grain size analysis, Atterberg’s limit test,compaction test, direct shear test, California bearing ratio(CBR) test and permeability analysis. The study indicated that the dumpsite soils from four study regions show decreasing trends in the values of maximum dry density(MDD), specific gravity, cohesion and CBR, and increasing permeability as compared to the natural soil. The results show that the geotechnical properties of the soils at all four study locations have been severely hampered due to contamination induced by open dumping of waste.

Charging for the waste dumping of open-pit metal mines

Based on the externality theory and the environmental value theory, the hypothesis of charging for waste dumping of open-pit metal mines was put forth. The charging methods were designed according to the characteristics of waste dumping of openpit metal mines, including charging based on the dumping amount of the total waste, multi-charging factors, exceeding standard punishment charging, and so on. The main charging parameter is based on the dumping area rather than the total amount of waste dumping. The charging model of waste dumping of open-pit mines was formulated, and the charging rate was divided into two parts, i.e., the standard charging rate and the differential charging rate. The standard charging rate was derived using the equilibrium dynamic model, whereas the differential one was obtained by establishing the fuzzy synthesized evaluation model.

Numerical Simulation for Remediation Planning for 1,4-Dioxane-Contaminated Groundwater at Kuwana Illegal Dumping Site in Japan Based on the Concept of Verified Follow Up

At Kuwana illegal dumping site in Japan, where hazardous waste was illegally dumped, groundwater was severely contaminated by Volatile Organic Compounds (VOCs). Groundwater was already remedied by conducting Pump-and-Treat (P&T) after containment of all the waste by vertical slurry walls from 2002 to 2007. However, 1,4-dioxane was detected in both waste and groundwater outside of slurry walls after it was newly added into Japan environmental standards in late 2009, which suggested that the walls did not contain 1,4-dioxane completely. Our previous study developed a model to predict the 1,4-dioxane distribution in groundwater after the previous remediation at the site. In this study, numerical simulation was applied for remediation planning at the site based on the concept of Verified Follow Up (VF-UP) that had been proposed as a new approach to complete remediation effectively with consideration of future risks. The amount of waste to be removed and pumping plans were discussed by numerical simulation to achieve the remedial objective in which 1,4-dioxane in groundwater outside of walls is remedied within 10 years and 1,4-dioxane spreading throughout the walls is prevented in the case where a portion of waste is remained. Firstly, the amount of waste to be removed considering pumping plans for P&T was determined by scenario analysis. As a result, at least two-third of waste should be removed by combining with P&T. However, if the waste is remained, future risks of 1,4-dioxane spreading through the slurry walls may occur. Our simulation suggested that groundwater within the remaining waste must be pumped up at least 20 m3/d for containment of 1,4-dioxane within the remaining waste. In conclusion, our numerical simulation determined the amount of waste to be removed and the pumping plans for P&T to achieve the remedial objective effectively considering future risks based on the concept of VF-UP.

Study on Formation Mechanism of Dumping Piles on Dumping Area Stability

Dumping areas represent a stable hazard. To clarify the formation mechanism of dumping piles on dumping area stability, an investigation in open pit mine was performed. Moreover, experiments with gravel were conducted based on the research site conditions. The geological conditions, dumping operation, and waste particle size distribution were investigated in the Heidaigou open pit mine. Particle size distribution, dumping height, dumping volume, and floor inclination were varied to examine their effects on a single pile formation. The design of blasting can be modified to make the particle size of waste smaller. The volume of the bucket does not have a pronounced effect on dumping pile repose angle, capacity of dumping pile, and dumping area stability. The smaller the floor inclination, the better it is. Two measures are proposed to increase the kinetic force of friction between waste material and floor surface. The interval distance, dumping volume and dumping height were also varied to examine the interaction between the formations of multiple piles. The dumping width should be decided through optimization efficiency of bulldozer and dumping device in bucket wheel excavator-belt-stacker dumping operation and dragline dumping operation. Moreover, the volume of the bucket does not have a pronounced interaction effect. In the dumping operation, the work amount of bulldozer decreases as dumping pile increases. The design of the dumping operation must consider the total efficiency of ground leveling operation and forming dumping the area.

Preliminary prospective study of real-time post-gastrectomy glycemic fluctuations during dumping symptoms using continuous glucose monitoring

BACKGROUND Although dumping symptoms constitute the most common post-gastrectomy syndromes impairing patient quality of life,the causes,including blood sugar fluctuations,are difficult to elucidate due to limitations in examining dumping symptoms as they occur.AIM To investigate relationships between glucose fluctuations and the occurrence of dumping symptoms in patients undergoing gastrectomy for gastric cancer.METHODS Patients receiving distal gastrectomy with Billroth-I(DG-BI)or Roux-en-Y reconstruction(DG-RY)and total gastrectomy with RY(TG-RY)for gastric cancer(March 2018-January 2020)were prospectively enrolled.Interstitial tissue glycemic profiles were measured every 15 min,up to 14 d,by continuous glucose monitoring.Dumping episodes were recorded on 5 patient-selected days by diary.Within 3 h postprandially,dumping-associated glycemic changes were defined as a dumping profile,those without symptoms as a control profile.These profiles were compared.RESULTS Thirty patients were enrolled(10 DG-BI,10 DG-RY,10 TG-RY).The 47 early dumping profiles of DG-BI showed immediately sharp rises after a meal,which 47 control profiles did not(P<0.05).Curves of the 15 late dumping profiles of DG-BI were similar to those of early dumping profiles,with lower glycemic levels.DGRY and TG-RY late dumping profiles(7 and 13,respectively)showed rapid glycemic decreases from a high glycemic state postprandially to hypoglycemia,with a steeper drop in TG-RY than in DG-RY.CONCLUSION Postprandial glycemic changes suggest dumping symptoms after standard gastrectomy for gastric cancer.Furthermore,glycemic profiles during dumping may differ depending on reconstruction methods after gastrectomy.

Slope stability of increasing height and expanding capacity of south dumping site of Hesgoula coal mine:a case study

This paper is devoted to improve the containment capacity of the Hesgoula south dumping site.The general geology of the dumping site was obtained through geological surveys.Physico-mechanical properties of silty clay and bedrock layers that have a large impact on the stability of the dump were measured by direct shear tests and triaxial tests in laboratory.Then ultimate bearing capacity of the substrate were analyzed and calculated.This paper proposed three capacity expansion and increase plans and used GeoStudio software for comparison.Through computation of the stability of the dump site slope after capacity expansion and increase for each plan,the capacity expansion plan was determined.The capacity expansion and increase plan will solve the problem of the current insufficient containment capacity of the Hesgoula south dumping site,which is of great significance for saving mine transportation costs,improving work efficiency,and reducing grassland occupation.

Lixiviation of Open-Coast Dumping Site and Pollution of Water and Soils of Edea Industrial Zone（Littoral-Cameroon）

The nexus between water, food and energy is one of the most fundamental relationships and challenges for society. Indeed, seepage of wastes stored into dumping sites of Edea township, favor their lixiviation. Soluble components of matter are slowly dissolves, drained by meteoric water and flowed into tail bay vicinity. Knowledge of trace and toxic metal concentrations in the biotic matrices is important for assessing the effects of pollutants and the risk of exposure. In this study, A1, Mn, Cd, Cr, Cu, Pb and Zn were quantified respectively in 33 samples of soil and water, using ICP-MS （Inductively Coupled Plasma Mass Spectrometry）, Pb were found between 1.38-88.28 mg/L. Higher concentrations of Al were found in Alucam industrial wastes （315,502.33 mg/kg）, and in Hysacam domestic wastes （54,126.93 mg/kg）. Concentrations of Cd （1.955 mg/kg）, Pb （469.00 mg/kg） and Zn （853.00 rng/kg） are higher in domestic wastes. The ones of Mn （696.96 mg/kg） and Cu （1,320.10 mg/kg） are higher in industrial wastes. Higher concentrations of Pb and Cu let assume that it is a risk of poisoning relative to these elements around this area. These findings illustrate that lixiviation of dumping wastes has great influence on water and soils pollutions of the study ecosystem.

Solid Waste Dumping Site Selection Using GIS and Remote Sensing for Kajiado County, Kenya

Solid waste dumping is a hectic problem in urban and developing areas due to shortage of land for the purpose. The main objective of this study was to select potential areas for suitable solid waste dumping for Kajiado County, Kenya. Eight input map layers including DEM （digital elevation model）, topography, urban settlement, roads, wetlands, rivers, forests and protected areas were prepared and MCDA （Multi Criteria Decision Analysis Methods） were implemented in a GIS （geographic information systems） environment. GIS, RS （remote sensing） and MDCA are powerful tools which can effectively be applied during the planning phase of solid waste management in order to avoid adverse catastrophes in future. The final suitability map was prepared by weighted overlay analyses and leveled as the most suitable, moderate suitable, less suitable and unsuitable areas. The area of each suitability level was calculated using spatial statistics. Polygons representing the most suitable sites were further analyzed in terms of area perimeter ratio in order to investigate the most suitable areas in terms of shape regularity. The leading four polygons considered were marked A, B, C, D respectively in the final map. This study showed that suitable areas for solid waste landfills were limited and scattered in the study area.

Study on Improvement of Dumping Site Stability in Weak Geological Condition by Using Compacted Layer

Berau Basin, a sub-basin of Tarakan Basin, had been developed during Eocene to Miocene period. Rocks in Berau Basin consist of sedimentary, volcanic and igneous rocks aged from Pre-tertiary until Quaternary epoch. The youngest identified rock formation was alluvial deposit consists of mud, silt, sand, gravel and swamp with brown to dark color. This youngest rock formation is relatively weak geological condition and can cause problems in the coal mining operation. PT Berau Coal as one of the coal mining companies in Berau Basin area had experienced some problems related to the occurrence of alluvial deposit. A large failure has occurred at one of its out pit dumping?area which lies over the swamp material. The failure caused a higher operating cost since it made that the distance for waste rock dumping became to be farther than the designated area. Therefore, in order to prevent similar failure occurring at dumping area which lies above swamp material, an improvement of dumping site stability on weak geological condition has to be needed. The proposed method for improving the stability of out pit dumping area in weak geological condition is to construct the compacted layer of waste rock before the out pit dumping area construction. Based on experimental results, a minimum of 40 kPa pressure is needed to give a proper compaction to the waste rock. The result of numerical analysis by Finite Element Method (FEM) shows that construction of compacted layer on the base of out pit dumping area can improve its stability.

Turning ash dumping yards into cultivated land

I.IntroductionIt is common practice to dump the largequantity of fly ash collected from the burn-ing of pulverized coal in coal-fired thermal powerstations in ash dumping yards constructed overlow-lying land or in the mountain valleys,whichnot only occupies large areas of land,but is alsoa public nuisance when the dried fly ash is blownup by wind.In the past it was advocated to coverthe ash dump with a layer of soil to prevent theash from being stirred up and also to grow cropson the soil-covered fly ash.Success to someextent has been claimed.However,to cover thelarge areas of ash dump requires considerablequantity of soil:to surface an ash dump of 100hectares with a thickness of only 0.2m willrequire 200,000m^3 of soil.Under the

600WM汽轮机高压主汽门及高压调门DUMP阀故障分析与处理

介绍了DUMP阀的作用、结构原理,结合某电厂高压主汽门、高压调门几次故障案例,分析研究DUMP阀发生故障的原因,并提出相应的处理措施,为类似问题的解决提供了参考和借鉴。

Legacy Gold Mine Sites & Dumps in the Witwatersrand: Challenges and Required Action

Legacy mine shafts and waste dumps in the Witwatersrand continue to create social and environmental challenges for communities, even in areas where gold mining ceased over 100 years ago. The slow pace of eradication of these gold mine shafts and waste dumps (or lack thereof) results in conflict between the communities and authorities, particularly the Department of Mineral Resources and Energy (DMRE) as the relevant authority in the field of environmental management in mining. This paper examines, through a literature review, the past and present legislative framework that resulted in legacy mine shafts and dumps and how communities find themselves living next to these mine sites, which results in social and environmental problems. The paper further explores the governments, particularly the DMRE, proposed initiatives to empower those who intend to extract value from the abandoned mines while curbing the scourge of crime in affected communities.

An ensemble machine learning model to uncover potential sites of hazardous waste illegal dumping based on limited supervision experience

With the soaring generation of hazardous waste(HW)during industrialization and urbanization,HW illegal dumping continues to be an intractable global issue.Particularly in developing regions with lax regulations,it has become a major source of soil and groundwater contamination.One dominant challenge for HW illegal dumping supervision is the invisibility of dumping sites,which makes HW illegal dumping difficult to be found,thereby causing a long-term adverse impact on the environment.How to utilize the limited historic supervision records to screen the potential dumping sites in the whole region is a key challenge to be addressed.In this study,a novel machine learning model based on the positive-unlabeled(PU)learning algorithm was proposed to resolve this problem through the ensemble method which could iteratively mine the features of limited historic cases.Validation of the random forest-based PU model showed that the predicted top 30%of high-risk areas could cover 68.1%of newly reported cases in the studied region,indicating the reliability of the model prediction.This novel framework will also be promising in other environmental management scenarios to deal with numerous unknown samples based on limited prior experience.