Adsorption of acid and basic dyes by sludge-based activated carbon:Isotherm and kinetic studies

A batch experiment was conducted to investigate the adsorption of an acid dye(Acid Orange 51) and a basic dye(Safranine) from aqueous solutions by the sludge-based activated carbon(SBAC). The results show that the adsorption of Acid Orange 51 decreases at high p H values, whereas the uptake of Safranine is higher in neutral and alkaline solutions than that in acidic conditions. The adsorption time needed for Safranine to reach equilibrium is shorter than that for Acid Orange 51. The uptakes of the dyes both increase with temperature increasing, indicating that the adsorption process of the dyes onto SBAC is endothermic. The equilibrium data of the dyes are both best represented by the Redlich-Peterson model. At 25 °C, the maximum adsorption capacities of SBAC for Acid Orange 51 and Safranine are 248.70 mg/g and 525.84 mg/g, respectively. The Elovich model is found to best describe the adsorption process of both dyes, indicating that the rate-limiting step involves the chemisorption. It can be concluded that SBAC is a promising material for the removal of Acid Orange 51 and Safranine from aqueous solutions.

Adsorption of Natural Aluminium Dye Complex from Silk-Dyeing Effluent Using Eucalyptus Wood Activated Carbon

Two activated carbons with controlled pore size were prepared from Eucalyptus wood by physical activation with carbon dioxide, giving the BET surface area and pore volume of738 m2/g and0.39 cm3/g, and921 m2/g and0.53 cm3/g for the carbon sample AC1 and AC2, respectively. These activated carbons were then used to remove the residual dye left after the silk-dyeing process. The dye solution used for adsorption study was a cationic aluminium dye complex of [Al(brazilein)2]+ derived from a mixture of alum and extract of the heartwood of Ceasalpinia sappan Linn., with initial dye concentration of 220 mg/l. Effects of adsorbent dosage, adsorption time and temperature in the range of 25℃40℃ on dye adsorption were investigated. It was found that the adsorption kinetics of this dye complex was best described by the pseudo-second order model. Adsorption isotherms of this dye complex were well fitted by Langmuir isotherm equation. The adsorption capacities for the uptake of this dye complex at 25℃, 30℃ and 40℃ were 718.7, 1240.4 and 1139.5 mg/g and 1010.5, 1586.1 and 1659.0 mg/g for carbon sample AC1 and AC2, respectively. From these results, it can be concluded that activated carbon containing a higher proportion of mesopores gave better dye removal efficiency, emphasizing the fact that a proper pore size distribution of carbon adsorbent is crucial for the effecttive removal of relatively large size of the dye molecules. Thermodynamic parameters, including free energy, enthalpy and entropy of adsorption, were also determined. The adsorption enthalpies for the removal of this dye complex of AC1 and AC2 were 105.3 and 55.6 kJ/mol, respectively, indicating that the adsorption is an endothermic process. It was found that the adsorption of this dye complex is spontaneous at the temperatures under investigation.

Preparation of activated carbon from cattail and its application for dyes removal

Activated carbon was prepared from cattail by H3PO4 activation. The effects influencing the surface area of the resulting activated carbon followed the sequence of activated temperature 〉 activated time 〉 impregnation ratio 〉 impregnation time. The optimum condition was found at an impregnation ratio of 2.5, an impregnation time of 9 hr, an activated temperature of 500℃, and an activated time of 80 min. The Brunauer-Emmett-Teller surface area and average pore size of the activated carbon were 1279 m^2/g and 5.585 nm, respectively. A heterogeneous structure in terms of both size and shape was highly developed and widely distributed on the carbon surface. Some groups containing oxygen and phosphorus were formed, and the carboxyl group was the major oxygen-containing functional group. An isotherm equilibrium study was carried out to investigate the adsorption capacity of the activated carbon. The data fit the Langmuir isotherm equation, with maximum monolayer adsorption capacities of 192.30 mg/g for Neutral Red and 196.08 mg/g for Malachite Green. Dye-exhausted carbon could be regenerated effectively by thermal treatment. The results indicated that cattail-derived activated carbon was a promising adsorbent for the removal of cationic dyes from aqueous solutions.

Platanus orientalis leaves based hierarchical porous carbon microspheres as high efficiency adsorbents for organic dyes removal

Water contamination caused by hazardous organic dyes has drawn considerable attention, among all of the techniques released, adsorption has been widely used, which however to a large degree is dependent on the development of high efficiency adsorbents. Waste biomass based porous carbon is becoming the new star class of adsorbents, and thus contribute more to the sustainable development of the society. In this work, for the first time to the best of our knowledge, abundant waste fallen Platanus orientalis leaves are employed as the raw material for hierarchical activated porous carbon(APC) microspheres via a mild hydrothermal carbonization(210 ℃,12.0 h) followed by one-step calcination(750 ℃, 1.0 h). The APC microspheres exhibit a specific surface area of 1355.53 m^2·g^-1 and abundant functional groups such as O—H and C=O. Furthermore, the APC microspheres are used as the adsorbents for removal of Rh B and MO, with the maximum adsorption capabilities of 557.06 mg·g^-1 and 327.49 mg·g^-1, respectively, higher than those of the most porous carbon originated from biomass. The adsorption rates rapidly approach to 98.2%(RhB) and 95.4%(MO) within 10 min. The adsorption data can be well fitted by Langmuir isotherm model and the pseudo-second-order kinetic model, meanwhile the intra-particle diffusion and Boyd models simultaneously indicate that the diffusion within the pores is the main rate-limiting step. Besides, the APC microspheres also demonstrate good recyclability, and may also be applied to other areas such as heterogeneous catalysis and energy storage.

Recyclable adsorbent of BiFeO_3/Carbon for purifying industrial dye wastewater via photocatalytic reproducible

It is essential to prepare highly-efficiency reproducible adsorbent for purifying industrial dye wastewater. In this work, biscuit with a layered porous structure as a template is applied to prepare a photocatalytic recyclable adsorbent of BiFeO3/Carbon nanocomposites for purifying simulative industrial dye wastewater. It is found that the structure of the prepared BiFeO3/Carbon nanocomposite is related to the natural structure of the biscuit, annealing temperatures and immersing times, demonstrated by XRD, TEM, UV-Vis and adsorptive activities. Kinetics data shows that the adsorption rate of the adsorbent to the dye is rapid and fitted well with the pseudo-second-order model, that more than 80% of dyes can be removed in the beginning 30 min. The adsorption isotherm can be perfectly described by the Langmuir model as well. It can be seen from the adsorption data that the adsorption performance can reach over 90% at pH ? 2–12, which can imply its universal utilization. The prepared BiFeO_3/Carbon nanocomposites have also displayed excellent capacities(over 90% within 30 min) for adsorption of seven different dyes and their mixed one. According to the five times photocatalytic reproducible experiments, it is proved that BiFeO_3/Carbon nanocomposites show the excellent stability and reproduction for purifying simulative industrial dyes, even the sample have been placed for one year. These research results indicate that the adsorbent BiFeO_3/Carbon can be a suitable material used in treating industrial dye wastewater potentially.

Carbonaceous Nanofibers-titanium Dioxide Nanocomposites: Synthesis and Use as a Platform for Removal of Dye Pollutants

A mild chemistry route was developed to prepare carbonaceous nanofibers-titanium dioxide(CNF-TiO_2) nanocomposites for removal of dye pollutants. In the process of the template-directed hydrothermal carbonization(HTC), ultrathin Te nanowires were adopted as templates and glucose as the carbon source, and TiO_2 was decorated on CNF via the hydrolysis of tetrabutyltitanate in the presence of CNF in ethanol. The as-prepared materials were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), energy-dispersive X-ray(EDX) and X-ray diffraction(XRD). SEM and TEM observations displayed that TiO_2 nanoparticles were anchored on the CNF. EDX and XRD data confirmed that the assynthesized samples were CNF-TiO_2, and TiO_2 belonged to anatase titania. Taking advantage of combined benefits of carbonaceous nanofibers and titanium dioxide, these CNF-TiO_2 nanocomposites exhibited higher removal efficiency in a short time and showed good reusability. It was showed that over 97% of Rhodamine B could be removed in 15 min without generating the solid and liquid wastes. The removal efficiency of dyes was still over 80% after reuse in five cycles. All the results demonstrate that the as-prepared CNF-TiO_2 composites are effective materials for fast and effective removal of dye pollutants and thus can provide a new platform for dye decontamination.

Adsorption of dyes onto activated carbon prepared from olive stones

Activated carbon was produced from olive stones（OSAC） by a physical process in two steps. The adsorption character of this activated carbon was tested on three colour dyes molecules in aqueous solution： Methylene blue（MB）, Rhodamine B（RB） and Congo Red（CR）. The adsorption equilibrium was studied through isotherms construction at 30℃, which were well described by Langmuir model. The adsorption capacity on the OSAC was estimated to be 303 mg/g, 217 mg/g and 167 mg/g respectively for MB, RB and CR. This activated carbon has a similar adsorption properties to that of commercial ones and show the same adsorption performances. The adsorption kinetics of the MB molecule in aqueous solution at different initial concentrations by OSAC was also studied. Kinetic experiments were well fitted by a simple intra-particle diffusion model. The measured kinetics constant was influenced by the initial concentration and we found the following correlation： Kid = 1.55 C0^0.51.

Heteroatom-doped porous carbon from methyl orange dye wastewater for oxygen reduction

Banana peel-derived porous carbon(BPPC) was prepared from banana peel and used as an adsorbent for methyl orange(MO) wastewater removal. BPPC-MO50 is a N,S-doped BPPC obtained via secondary carbonization. The BPPC-MO50 exhibited a high specific surface area of1774.3 m^2/g. Heteroatom-doped porous carbon(PC) was successfully synthesized from the BPPC absorbed MO at high temperature and used for oxygen reduction. The BPPC-MO50 displayed the highest ORR onset potential among all carbon-based electrocatalysts, i.e., 0.93 V vs.reversible hydrogen electrode(RHE). This is the first report to describe porous carbon-activated materials from agriculture and forestry waste that is used for adsorption of dyes from wastewater via an enhanced heteroatom(N,S) content. These results may contribute to the sustainable development of dye wastewater treatment by transforming saturated PC into an effective material and has potential applications in fuel cells or as energy sources.

High surface area and mesoporous activated carbon from KOH-activated dragon fruit peels for methylene blue dye adsorption:Optimization and mechanism study

In this study,an alternative precursor for production of activated carbon was introduced using dragon fruit(Hylocereus costaricensis)peel(DFP).Moreover,KOH was used as a chemical activator in the thermal carbonization process to convert DFP into activated carbon(DFPAC).In order to accomplish this research,several approaches were employed to examine the elemental composition,surface properties,amorphous and crystalline nature,essential active group,and surface morphology of the DFPAC.The BrunauerEmmettTeller test demonstrated a mesoporous structure of the DFPAC has a high surface area of 756.3 m2g 1.The cationic dye Methylene Blue(MB)was used as a probe to assess the efficiency of DFPAC towards the removal of MB dye from aqueous solution.The effects of adsorption input factors(e.g.DFPAC dose(A:0.040.12 g L 1),pH(B:310),and temperature(C:3050℃))were investigated and optimized using statistical analysis(i.e.BoxBehnken design(BBD)).The adsorption kinetic model can be best categorized as the pseudofirst order(PFO).Whereas,the adsorption isotherm model can be best described by Langmuir model,with maximum adsorption capacity of DFPAC for MB dye was 195.2 mg g 1 at 50℃.The adsorption mechanism of MB by DFPAC surface was attributed to the electrostatic interaction,pp interaction,and Hbonding.Finally,the results support the ability of DFP to be a promising precursor for production of highly porous activated carbon suitable for removal of cationic dyes(e.g.MB).

Error Analysis of Adsorption Isotherm Models for Acid Dyes onto Bamboo Derived Activated Carbon

High surface area activated carbons were produced by thermal activation of waste bamboo scaffolding with phosphoric acid.Single component equilibrium dye adsorption was conducted on the carbons produced and compared with a commercially available carbon.Two acid dyes with different molecular sizes,namely Acid Yellow 117(AY117) and Acid Blue 25(AB25),were used to evaluate the adsorption capacity of the produced carbons.It was found that the dye with smaller molecular size,AB 25,was readily adsorbed onto the produced carbon,nearly three times higher than a commercially available carbon,while the larger size dye,AY117,showed little adsorption.The experimental data were analyzed using isotherm equations including Langmuir,Freundlich,Tempkin,Toth,Redlich-Peterson and Sips equations.The equilibrium data were then analyzed using five different non-linear error analysis methods.

Role of the surface chemistry of activated carbons in dye removal from aqueous solution

Commercial activated carbons were modified by a series of chemical or physical treatments using H202, NH3, and heating under N2 flow without notably changing their pore structures. The resultant carbons were characterized by N2 adsorption and Bohem titration and then used to remove Ponceau 4R, methyl orange and brilliant blue from aqueous solutions. Surface chemistry was found to play a signifi- cantly different role in removing these three compounds. The removal of anionic Ponceau 4R increases with increasing carbon surface ba- sicity due to the predominant dispersive interaction mechanism. In contrast, surface chemistry has little effect on the removal of anionic methyl orange, which can be explained by two parallel mechanisms involving electrostatic and dispersive interactions due to the basic amine group in a dye molecule. The influence of surface chemistry on the removal of amphoteric brilliant blue dye can also be ignored due to a weak interaction between the carbons and dye molecules, which is resulted from strong cohesive energy from electrostatic forces inside amphoteric dye molecules.

Adsorption of Reactive Dyes on Activated Carbon Developed from <i>Enteromorpha prolifera</i>

Activated carbon was prepared from Enteromorpha prolifera by zinc chloride activation. The adsorption behaviors of three reactive dyes (Reactive Red 23, Reactive Blue 171 and Reactive Blue 4) onto this biomass activated carbon were investigated in batch systems. The experimental findings showed that the removal efficiencies of three dyes onto activated carbon were maximum at the initial solution pH of 4.5 - 6.0. Thermodynamic studies suggested that adsorption reaction was an endothermic and spontaneous process. Adsorption isotherm of the three dyes obeyed Freundlich isotherm modal. Dye adsorption capacities of activated carbon were 59.88, 71.94 and 131.93 mg·g?1 for RR23, RB171 and RB4 at 27?C, respectively. Second-order kinetic models fitted better to the equilibrium data of three dyes. The adsorption process on activated carbon was mainly controlled by intraparticle diffusion mechanism.

A Bi-layer Composite Film Based on TiO_2 Hollow Spheres, P25,and Multi-walled Carbon Nanotubes for Efficient Photoanode of Dye-sensitized Solar Cell

A bi-layer photoanode for dye-sensitized solar cell(DSSC) was fabricated, in which TiO_2 hollow spheres(THSs) were designed as a scattering layer and P25/multi-walled carbon nanotubes(MWNTs) as an under-layer. The THSs were synthesized by a sacrifice template method and showed good light scattering ability as an over-layer of the photoanode. MWNTs were mixed with P25 to form an under-layer of the photoanode to improve the electron transmission ability of the photoanode. The power conversion efficiency of this kind of DSSC with bi-layer was enhanced to 5.13 %,which is 14.25 % higher than that of pure P25 DSSC.Graphical Abstract A bi-layer composite photoanode based on P25/MWNTs-THSs with improved light scattering and electron transmission, which will provide a new insight into fabrication and structure design of highly efficient dyesensitized solar cells.

Enhanced degradation of reactive dyes using a novel carbon ceramic electrode based on copper nanoparticles and multiwall carbon nanotubes

A novel carbon ceramic electrode consisting of Cu NPs and MWCNT was developed to treat reactive orange 84(RO84) wastewater using ultrasound-assisted electrochemical degradation. The proposed electrode generated more hydroxyl radicals than non-nanoparticle electrodes did. In addition, a new electrochemical sensor was applied to determine residue RO84 in an aqueous medium during discoloration. This sensor is based on a glassy carbon electrode modified with gold nanourchins and graphene oxide and can detect RO84 concentration in the range of 1.0–1200 μmol·L^-1 with the detection limit of 0.03 μmol·L^-1. The degradation effects of the modified electrode on RO84 were evaluated systematically with different initial pH values, time durations, and amounts of Cu NPs and MWCNT. The results suggested that the removal efficiency of RO84 was approximately 83% after120 min of electrolysis in a phosphate buffer with pH 8.0 using a carbon ceramic electrode made with 4.0 wt%Cu NPs and 4.0 wt% MWCNT. The possible mechanism of RO84 degradation was monitored by gas chromatography–mass spectrometry, and degradation pathways were proposed.

Low temperature fabrication of flexible carbon counter electrode on ITO-PEN for dye-sensitized solar cells

A novel low temperature method was used to prepare the mesoporous carbon（MC） counter electrode（CE） on indium-doped tin oxide coated polyethylene naphthalate（ITO-PEN） for flexible dye-sensitized solar cells（DSSCs）.The obtained flexible MC CEs with carbon loading of 280μg cm^（-2） were characterized by SEM,XRD and electrochemical impedance.The light-to-electricity conversion efficiency of the DSSC fabricated with the prepared flexible MC CE was 86%of that of DSSC based on the decomposited Pt CE.

Removal of Dyes from Wastewater by Adsorption onto Activated Carbon: Mini Review

Nowadays, wastewater from dyeing industries became a challenging issue in the world. Researchers have reported several techniques to treat those effluents based on their projects. Adsorption is the most common method because of cheap, simple and effective method. In this work, activated carbon was used for dye adsorption purpose. This adsorbent has high surface area and high porosity to remove dye. This review highlighted some important results of the last few years regarding the use of activated carbon in wastewater treatment. Research findings supported that adsorption process is spontaneous in nature. Adsorption data confirmed Langmuir model, indicating the chemisorption occurred.

Orientation in Nematic Liquid Crystals Doped with Orange Dyes and Effect of Carbon Nanoparticles

Some properties of nematic liquid crystal E7 doped with two disperse orange dyes used together and effect of addition of carbon nanoparticles （single walled carbon nanotube or fullerene C60） on them were studied. Two dyes （disperse orange 11 and 13） having high solubility and order parameter were used as co-dopants. A notable increase in order parameter was obtained comparing to that of liquid crystal doped with single dye. When carbon nanoparticles were used as dopant, a decrease in order parameter was observed at low temperatures while it increased at high temperatures. When applied voltage changed, the order parameter abruptly increased in its threshold value and saturated in higher voltages as expected. An appreciable change in textures was not observed with addition of dopants. This addition gave rise to an increase in nematic-isotropic phase transition temperatures compared with that of pure liquid crystal.

Adsorption of Indigo Carmine Dye by Composite Activated Carbons Prepared from Plastic Waste (PET) and Banana Pseudo Stem

This study is on the adsorption of indigo carmine dye by composite activated carbons prepared from banana pseudo stems and plastic waste. The activated carbons named TB1P1, TB1P1h and TB2P1 were obtained by pyrolysis at 700°C under steam of raw materials at different ratios (1:1 and 2:1). They were characterized by different techniques such as SEM/EDX, Raman Spectroscopy, FTIR, XRD, TGA/DTA and BET/BJH. Analyses indicate amorphous structures with specific surface areas of 424.37;385.45 and 338.84 m2/g for TB1P1, TB1P1h and TB2P1 respectively. The study of the adsorption of indigo carmine dye by these adsorbents was carried out by varying parameters such as contact time, mass of adsorbent and initial concentration of the dye. The maximum retention is 94.71%, 86.18% and 84.17% for TB1P1, TB1P1h and TB2P1 respectively after 60 min of stirring, for a pH = 4.6 using 0.6 g of adsorbents. The adsorption of indigo carmine follows well, the Langmuir model, with the most suitable kinetics as pseudo second order.

Synthesis of activated carbons from black sapote seeds,characterization and application in the elimination of heavy metals and textile dyes

Many different techniques may be used to remove industrial pollutants from wastewater. Adsorption using activated carbon has been reported to be an effective method. This work proposes the use of a vegetable residue(black sapote seeds) as a raw material for its synthesis. These carbons were chemically activated using phosphoric acid and carbonized at 673 and 873 K. Adsorption isotherms were constructed for the textile dyes on the carbons, and this data was treated using Langmuir’s equation to quantitatively describe the adsorption process. The synthesized carbons were characterized using FTIR, EA, SEM, Nitrogen adsorption(specific surface areas of 879 and 652 m2·g-1), and their points of zero charge(2.1 and 2.3). It was possible to adsorb both heavy metals and textile dyes present in aqueous solutions and wastewaters using these activated carbons. Heavy metals were adsorbed almost completely by both carbons. Cationic dyes where adsorbed(58–59.8 mg·g-1) in greater amounts compared to anionic dyes(10–58.8 mg·g-1). The amount of anionic dyes adsorbed increased almost 30% by changing the pH of the solutions. One of the carbons was thermally regenerated on three occasions without losing its adsorption capacity and it was proved in a flow system.

Removal of Dispersed Dyes from Aqueous Solution Using Activated Carbon Prepared from Olive Stones

In order to valorize olive stones and to show its potential use in the sorption of two dispersed dyes, it was transformed in activate carbon and characterized. The effects of different system variables： pH, agitation speed, temperature and initial dye concentration were studied in the batch tests. The adsorption capacity of activated carbon for the dyes removal was found to be affected by the solution＇s pH. Acidic pH was found the favour disperse dyes removal. Over 95% removal was achieved for both the dyes at pH 3. The equilibrium time for both dyes was 30 min. Both Langmuir and Freundlich isotherms could be used to describe the adsorption of the dyes. Freundlich adsorption model succeeded in fitting the adsorption isotherms of dyes on olive stones activated carbon in single-solute systems, and prediction of the competitive adsorption behavior of dyes with the Freundlich-based Sheindorf-Rebuhn-Sheintuch （SRS） model gave acceptable results.