Numerical investigation of dynamical behavior of tethered rigid spheres in supersonic flow

The dynamical behavior of two tethered rigid spheres in a supersonic flow is numerically investigated. The tethered lengths and radius ratios of the two spheres are different. The two spheres, which are centroid axially aligned initially, are held stationary first, then released, and subsequently let fly freely in a supersonic flow. The mean qualities of the system and the qualities of the bigger sphere are considered and compared with the situations without the tether. In the separation process, six types of motion caused by the spheres, tether, and fluid interaction are found. The results show that the mean x-velocity of the system changes in a different manner for different radius ratios, and the x-velocity of the bigger sphere is uniformly reduced but through different mechanisms.

Active Flow Control of a Low Reynolds Number S809 Wind Turbine Blade Model under Dynamic Pitching Maneuvers

A low Reynolds number wind turbine blade model based on the S809 airfoil was tested in a subsonic wind tunnel to study the structural vibration of the blade under dynamic pitching maneuvers. Piezoelectric-based synthetic jet actuators were embedded inside the blade and activated with a synthetic jet momentum coefficient, Cμ of 2.30 × 10-3. Structural vibration was quantified for a range of unsteady angles undergoing “pitch up and down” and “sinusoidal pitch” maneuvers at a Reynolds number of 5.28 × 104. The blade tip deflection amplitude and frequency were acquired utilizing a pair of strain gauges mounted at the root of the model. Using active flow control vibration reduction was more effective during the pitch up portion of the blade motion cycle compared to the pitch down portion. This effect is due to dynamic stall, where a leading edge vortex is shed during the pitch up motion and contributes to higher lift compared to static angles of attack and lower lift when the blade is pitched down. Dynamic stall was measured with phase-locked stereoscopic particle image velocimetry (SPIV), where global mean flow measurements reveal a shift in location and reduction in the size of a recirculating flow structure near the suction surface of the blade during the pitch up motion compared to the pitch down.

Dynamic Recrystallization Behavior of 7056 Aluminum Alloys during Hot Deformation

To investigate the dynamic recrystallization behavior of 7xxx aluminum alloys,the isothermal compression tests were carried on the 7056 aluminum alloy in the temperatures range of 320-440℃and in the strain rates range of 0.001-1 s^(-1).In addition,the microstructure of samples were observed via electron back scanning diffraction microscope.According to the results,true stress and true strain curves were established and an Arrhenius-type equation was established,showing the flow stress increases with the temperature decreasing and the strain rate increasing.The critical strain(ε_(c))and the critical stress(σ_(c))of the onset of dynamic recrystallization were identified via the strain hardening rate and constructed relationship between deformation parameters as follows:ε_(c)=6.71×10^(-4)Z^(0.1373) and σ_(p)=1.202σ_(c)+12.691.The DRX is incomplete in this alloy,whose volume fraction is only 20%even if the strain reaches 0.9.Through this study,the flow stress behavior and DRX behavior of 7056 aluminum alloys are deeply understood,which gives benefit to control the hot working process.

Effects ofslip mode on microstructure evolution and compressive flow behavior of extruded dilute Mg−0.5Bi−0.5Sn−0.5Mn alloy

The influence of the slip mode on the microstructure evolution and compressive flow behavior at different strains in an extruded dilute Mg−0.5Bi−0.5Sn−0.5Mn alloy was analyzed through electron backscatter diffraction,X-ray diffraction,transmission electron microscopy,and hot compression tests.The results showed that at a low strain of 0.05,the basal,pyramidaland<c+a>slip modes were simultaneously activated.Nevertheless,at the middle stage of deformation(strain of 0.1,0.2 and 0.5),theslip mode was difficult to be activated and<c+a>slip mode became dominant.The deformation process between strains of 0.2 and 0.5 was primarily characterized by the softening effect resulting from the simultaneous occurrence of continuous dynamic recrystallization and discontinuous dynamic recrystallization.Ultimately,at strain of 0.8,a dynamic equilibrium was established,with the flow stress remaining constant due to the interplay between the dynamic softening brought about by discontinuous dynamic recrystallization and the work-hardening effect induced by the activation of the basalslip mode.

DYNAMIC STRAIN AGING BEHAVIOR OF K40S ALLOY

The dynamic strain aging behavior during tensile tests of K40S alloy has been investigated in the temperature range of 25-1100℃ with the strain rate range from 10-4 to 10-3s-1. The results show that four different types of serration, identified as A, B, C and E type serration were observed in the temperature range of 300-600℃. The strain exponents for onset of the serrated flow were calculated as 1.21, 2.19 and 1.61, and the activation energies as 121, 40 and 67kJ/mol for E, B and C type serration respectively. The main mechanism for dynamic strain aging discussed in light of the strain exponent and the activation energy.

Dynamic recrystallization kinetics of as-cast AZ91D alloy

The flow behavior and dynamic recrystallization（DRX） behavior of an as-cast AZ91 D alloy were investigated systematically by applying the isothermal compression tests in temperature range of 220-380 ℃ and strain rate range of 0.001-1 s^-1.The effect of temperature and strain rate on the DRX behavior was discussed.The results indicate that the nucleation and growth of dynamic recrystallized grains easily occur at higher temperatures and lower strain rates.To evaluate the evolution of dynamic recrystallization,the DRX kinetics model was proposed based on the experimental data of true stress-true strain curves.It was revealed that the volume fraction of dynamic recrystallized grains increased with increasing strain in terms of S-curves.A good agreement between the proposed DRX kinetics model and microstructure observation results validates the accuracy of DRX kinetics model for AZ91 D alloy.

Size dependent flow behaviors of particles in hydrocyclone based on multiphase simulation

To investigate the flow behaviors of different size particles in hydrocyclone,a designed process was numerically simulated by the transient solver,where the quartz particles possessing a size distribution were injected into a 100 mm diameter hydrocyclone with the steady water field and air core inside.A lab experimental work has validated the chosen models in simulation by comparing the classification efficiency results.The simulated process shows that the 25 μm quartz particles,close to the cut size,need much more time than the finer and coarser particles to reach the steady flow rate on the outlets of hydrocyclone.For the particles in the inner swirl,with the quartz size increasing from 5 to 25 μm,the particles take more time to enter the vortex finder.The 25 μm quartz particles move outward in the radial direction when they go up to the vortex finder,which is contrary to the quartz particles of 5 μm and 15 μm as they are closely surrounding the air core.The studies reveal that the flow behaviors of particles inside the hydrocyclone depend on the particle size.

Hydrate agglomeration modeling and pipeline hydrate slurry flow behavior simulation

Dynamic modeling and numerical simulation of hydrate slurry flow behavior are of great importance to offshore hydrate management.For this purpose, a dynamic model of hydrate agglomeration was proposed in this paper.Based on population balance equation, the frame of the dynamic model was established first, which took both hydrate agglomeration and hydrate breakage into consideration.Then, the calculating methods of four key parameters involved in the dynamic model were given according to hydrate agglomeration dynamics.The four key parameters are collision frequency, agglomeration efficiency, breakage frequency and the size distribution of sub particles resulting from particle breakage.After the whole dynamic model was built, it was combined with several traditional solid–liquid flow models and then together solved by the CFD software FLUENT 14.5.Finally, using this method, the influences of flow rate and hydrate volume fraction on hydrate particle size distribution, hydrate volume concentration distribution and pipeline pressure drop were simulated and analyzed.

Constitutive modeling of flow behavior of precipitation-hardened AA7022-T6 aluminum alloy at elevated temperature

The thermomechanical behavior of precipitation-hardened aluminum alloy AA7022-T6 was studied using isothermal compression at temperatures of 623−773 K and strain rates of 0.01−1 s^−1.The experimental results indicated that dynamic recrystallization(DRX)is a predominant hot deformation mechanism,especially at elevated temperatures and low strain rates.The modified Johnson−Cook(J−C)and the strain compensated Arrhenius-type models were developed to predict the hot flow behavior under different deformation conditions.The correlation coefficients of modified J−C model and the strain compensated Arrhenius-type models were 0.9914 and 0.9972,respectively,their average relative errors(ARE)were 6.074%and 4.465%,respectively,and their root mean square errors(RMSE)were 10.611 and 1.665 MPa,respectively,indicating that the strain compensated Arrhenius-type model can predict the hot flow stress of AA7022-T6 aluminum alloy with an appropriate accuracy.

Determination of critical parameters for dynamic recrystallization in Ti-6Al-2Zr-1Mo-1V alloy

The true stress-strain curves of Ti-6Al-2Zr-1Mo-1V alloy were achieved by a series of isothermal compression tests with height reduction of 60% under the deformation temperatures of 1073-1323 K and the strain rates of 0.01-10s 1.The critical conditions for the onset of DRX were attained when the value of d /d,where strain hardening rate d /d,reached the minimum which corresponds to an inflection of θ versus σ curve.Thus,two important potential parameters,critical strain and critical stress,were identified,and expressed as εc/εp=0.37-0.60,σc/σp=0.81-0.91.Furthermore,by the regression analysis for conventional hyperbolic sine equation,the main material parameters such as α,β,n,and DRX activation energy,Q,were calculated.In addition,the evolution of Q with strain rate and temperature was revealed as a 3D response surface.

Dynamic modeling of twin roll casting AZ41 magnesium alloy during hot compression processing

A dynamic material model of Mg-4.51Al-1.19Zn-0.5Mn-0.5Ca(AZ41,mass fraction,%)magnesium alloy was put forward.The results show that the dynamic material model can characterize the deformation behavior and microstructure evolution and describe the relations among flow stress,strain,strain rates and deformation temperatures.Statistical analysis shows the validity of the proposed model.The model predicts that lower deformation temperature and higher strain rate cause the sharp strain hardening. Meanwhile,the flow stress curve turns into a steady state at high temperature and lower strain rate.The moderate temperature of 350 ℃and strain rate of 0.01 s-1 are appropriate to this alloy.

Influence of temperature, stress, and grain size on behavior of nano-polycrystalline niobium

Atomic simulations are executed to investigate the creep responses of nano-polycrystalline(NC) niobium established by using the Voronoi algorithm. The effects of varying temperature, applied stress, and grain size(GS) on creep properties and mechanisms are investigated. Notably, the occurrence of tertiary creep is exclusively observed under conditions where the applied stress exceeds 4.5 GPa and the temperature is higher than 1100 K. This phenomenon can be attributed to the significant acceleration of grain boundary and lattice diffusion, driven by the elevated temperature and stress levels. It is found that the strain rate increases with both temperature and stress increasing. However, an interesting trend is observed in which the strain rate decreases as the grain size increases. The stress and temperature are crucial parameters governing the creep behavior. As these factors intensify, the creep mechanism undergoes a sequential transformation: initially from lattice diffusion under low stress and temperature conditions to a mixed mode combining grain boundaries(GBs) and lattice diffusion at moderate stress and mid temperature levels, and ultimately leading to the failure of power-law controlled creep behavior, inclusive of grain boundary recrystallization under high stress and temperature conditions. This comprehensive analysis provides in more detail an understanding of the intricate creep behavior of nano-polycrystalline niobium and its dependence on various physical parameters.

Hot deformation behavior of spray forming LSHR alloy using constitutive equation and processing map

Flow behaviors of spray forming low solvus high refractory (LSHR) alloy were investigated using hot compression tests performed on a Gleeble?3500 thermal mechanical simulator at temperatures of 1020?1150 °C and strain rates of 0.0003?1.0 s?1. The constitutive equation was established, power dissipation (η) maps and hot processing maps were plotted. The microstructure evolution and dislocation distribution of domains with different values of η in power dissipation maps were also observed. The results show that the flow stress increases with decreasing temperature and increasing strain rate. The activation energy of the spray forming LSHR alloy is 1243.86 kJ/mol. When the value of η is 0.36 at the strain of 0.5, the domain in the processing map shows characteristics of typical dynamic recrystallization (DRX) and low dislocation density. According to the microstructure evolution and processing maps, the optimum processing condition for good hot workability of spray forming LSHR alloy can be summed up as:temperature range 1110?1150 °C; strain rate range 0.01?0.3 s?1.

Modification of constitutive model and evolution of activation energy on 2219 aluminum alloy during warm deformation process

To investigate the flow behavior of 2219 Al alloy during warm deformation, the thermal compression test was conducted in the temperature range of 483-573 K and the strain rate range of 0.001-5 s^-1 on a Gleeble-3500 thermomechanical simulation unit. The true stress-true strain curves obtained showed that the flow stress increased with the decrease in temperature and/or the increase in strain rate and the softening mechanism primarily proceeded via dynamic recovery. The modification on the conventional Arrhenius-type constitutive model approach was made, the material variables and activation energy were determined to be dependent on the deformation parameters. The modified flow stresses were found to be in close agreement with the experimental values. Furthermore, the activation energy obtained under different deformation conditions showed that it decreased with the rise in temperature and/or strain rate, and was also affected by the coupled effect of strain and strain rate.

Study on the Deformation Behavior of Mg-3.6%Er Magnesium Alloy

The deformation behaviour of a casting Mg-3.6% Er magnesium alloy after T6 treatment was studied in tensile tests from room temperature to 450 ℃ under different strain rates ranging from 1.0 ×10^-4 to 6.0 × 10^-3 S^-1 Obtained local plateau in the temperature dependence of the ultimate strength （σb） and yield strength （σ0.2） under constant strain rate indicated the presence of dynamic strain ageing （DSA）. Serrated flow was observed at the temperature of 200, 250, and 300 ℃. The observed negative strain rate sensitivity suggested that the serrated flow behavior arose from DSA. The temperature and strain rate dependence of the critical strain for the onset of serrated flow was analyzed using a phenomenological DSA equation, and the apparent activation energy Q for the serrated flow was obtained by calculation.

Processing map and hot deformation behavior of Ta-particle reinforced TiAl composite

The hot deformation behavior of a Ta-particle reinforced TiAl composite was studied.Ti-48Al-2Cr-2Nb-0.2 W(at.%)/20 vol.%Ta metal matrix composite was fabricated by spark plasma sintering.The deformation behavior was investigated by hot compression tests at the temperature ranging from 1050 to 1200℃ and the strain rate ranging from 1×10-3 to 1 s-1.The constitutive equation containing true strain variables was established.The values of activation energy Q under different strain degrees are between 240 and 280 kJ/mol,which are lower than that of pure TiAl.Based on dynamic material modeling,the processing maps at various strain degrees were established,and the optimized parameters for hot working are 1050-1100℃ and 0.005-0.01 s-1.The microstructural evolution during deformation was characterized,which indicated that the dynamic recrystallization plays an important role in this process.

Hot deformation behavior and constitutive modeling of Q345E alloy steel under hot compression

Q345E as one of typical low alloy steels is widely used in manufacturing basic components in many fields because of its eminent formability under elevated temperature. In this work, the deformation behavior of Q345E steel was investigated by hot compression experiments on Gleeble-3500 thermo-mechanical simulator with the temperature ranging from 850 ℃ to 1150 ℃ and strain rate ranging from 0.01 s-1 to 10 s-1. The experimental results indicate that dynamic softening of Q345E benefits from increasing deformation temperature and decreasing strain rate. The mathematical relationship between dynamic softening degree and deformation conditions is established to predict the dynamic softening degree quantitatively, which is further proved by some optical microstructures of Q345E. In addition, the experimental results also reveal that the stress level decreases with increasing deformation temperature and decreasing strain rate. The constitutive equation for flow stress of Q345E is formulated by Arrihenius equation and the modified Zener-Hollomon parameter considering the compensation of both strain and strain rate. The flow stress values predicted by the constitutive equation agree well with the experimental values, realizing the accurate prediction of the flow stress of Q345E steel under hot deformation.

The hot compressive deformation behavior of cast Mg-Gd-Y-Zn-Zr alloys with and without LPSO phase in their initial microstructures

Samples of Mg-8.2Gd-3.8Y-1.1Zn-0.4Zr alloy with and without an intragranular lamellae-shaped long period stacking ordered(LPSO)phase were prepared through heat treatment and a series of hot compression tests on these materials were conducted to examine and evaluate the influence of LPSO on the hot compressive deformation behavior and deformation mechanisms at a given alloy composition.The values of activation energy for plastic flow(Qc)of the solution treated(without LPSO phase)and annealed alloys(with intragranular LPSO phase)were larger than that for pure Mg,indicating that the presence of a high amount of rare earth(RE)elements and LPSO in the Mg matrix significantly increases Qc.The Qcvalue of the annealed alloy was larger than that of the solution treated alloy at all the strain levels(223.3 vs.195.5 k J/mol in average)and the largest difference in Qcbetween the two alloys was recorded at the smallest strain of 0.1 where precipitation of LPSO during deformation was limited in the solution treated alloy.These observations imply that the formation of LPSO phase out of the RE-rich solid solution matrix during deformation increases Qc,but the increment is not so large.Analysis of the hot compressive data of the alloys with LPSO phase and the alloys with RE-rich solid solution matrix in literatures indicates the similarity of the effect of the LPSO and RE-rich solid solution matrix phases on Qcand high-temperature strength.

Experimental Study on Magnetorheological Damper for Semi-Active Vibration Control of Civil Infrastructures

Magnetorheological (MR) fluid is a kind of smart material whose rheological properties can be rapidly varied in magnetic field. To make full use of the advantages of MR fluid to devices, a model of double ended, shear combined and valve typed MR damper is designed and manufactured, and the dynamic properties under sinusoidal excitations are experimentally studied. The experiment results show that the maximum damping force of the MR damper at the full magnetic intensity reaches about 20 kN while the maximum power required is less than 50 W, which predicts that the MR damper will be a powerful measurement for semi active vibration control of civil infrastructures.

Research Progress in Laser Active Debris Removal of CAST

Based on the introduction to theresearch status and trend of international space-based laser debris re-moval technology, the existing problems of space-based laser debris removal technology are systematically analyzed.In view of the existing problems, the work and research progress of the Beijing Institute of Spacecraft EnvironmentEngineering in this field are introduced from several aspects, such as dynamic behavior of laser-driven debris, orbittransfer model, ground simulation system, space-based removal system scheme and target selection strategy. The mainresearch methods include laser-driven micro-impulse measurement experiment, surface triangulation three-dimension-al reconstruction calculation method based on laser-material interaction theory, simulation calculation based on orbitaldynamics, etc. It also looks forward to the future research direction in the field of this technology.