Dynamic Modeling and Experimental Verification of an RPR Type Compliant Paralle Mechanism with Low Orders

Efficiency of calculating a dynamic response is an important point of the compliant mechanism for posture adjustment.Dynamic modeling with low orders of a 2R1T compliant parallel mechanism is studied in the paper.The mechanism with two out-of-plane rotational and one lifting degrees of freedom(DoFs)plays an important role in posture adjustment.Based on elastic beam theory,the stiffness matrix and mass matrix of the beam element are established where the moment of inertia is considered.To improve solving efficiency,a dynamic model with low orders of the mechanism is established based on a modified modal synthesis method.Firstly,each branch of the RPR type mechanism is divided into a substructure.Subsequently,a set of hypothetical modes of each substructure is obtained based on the C-B method.Finally,dynamic equation of the whole mechanism is established by the substructure assembly.A dynamic experiment is conducted to verify the dynamic characteristics of the compliant mechanism.

Time-Varying Mesh Stiffness Calculation and Dynamic Modeling of Spiral Bevel Gear with Spalling Defects

Time-varying mesh stiffness(TVMS)is a vital internal excitation source for the spiral bevel gear(SBG)transmission system.Spalling defect often causes decrease in gear mesh stiffness and changes the dynamic characteristics of the gear system,which further increases noise and vibration.This paper aims to calculate the TVMS and establish dynamic model of SBG with spalling defect.In this study,a novel analytical model based on slice method is proposed to calculate the TVMS of SBG considering spalling defect.Subsequently,the influence of spalling defect on the TVMS is studied through a numerical simulation,and the proposed analytical model is verified by a finite element model.Besides,an 8-degrees-of-freedom dynamic model is established for SBG transmission system.Incorporating the spalling defect into TVMS,the dynamic responses of spalled SBG are analyzed.The numerical results indicate that spalling defect would cause periodic impact in time domain.Finally,an experiment is designed to verify the proposed dynamic model.The experimental results show that the spalling defect makes the response characterized by periodic impact with the rotating frequency of spalled pinion.

General dynamic model for educational assembling-type robot and its fast simulation algorithm

To realize automatic modeling and dynamic simulation of the educational assembling-type robot with open structure, a general dynamic model for the educational assembling-type robot and a fast simulation algorithm are put forward. First, the educational robot system is abstracted to a multibody system and a general dynamic model of the educational robot is constructed by the Newton-Euler method. Then the dynamic model is simplified by a combination of components with fixed connections according to the structural characteristics of the educational robot. Secondly, in order to obtain a high efficiency simulation algorithm, based on the sparse matrix technique, the augmentation algorithm and the direct projective constraint stabilization algorithm are improved. Finally, a numerical example is given. The results show that the model and the fast algorithm are valid and effective. This study lays a dynamic foundation for realizing the simulation platform of the educational robot.

Three-Dimensional Dynamic Modeling of a Tangentially Fired Utility Boiler Furnace

The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the upper sections, lumped parameter model is used instead. With the combination of different models, we can get detailed distributions of gas velocity, temperature, chemical species, heat flux, etc. in the furnace, but with less CPU time. The radiation through the interfaces of each section is cons...

Dynamic Modeling and Motion Simulation for A Winged Hybrid-Driven Underwater Glider

PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.

Fault Prediction Based on Dynamic Model and Grey Time Series Model in Chemical Processes

This paper combines grey model with time series model and then dynamic model for rapid and in-depth fault prediction in chemical processes. Two combination methods are proposed. In one method, historical data is introduced into the grey time series model to predict future trend of measurement values in chemical process. These predicted measurements are then used in the dynamic model to retrieve the change of fault parameters by model based diagnosis algorithm. In another method, historical data is introduced directly into the dynamic model to retrieve historical fault parameters by model based diagnosis algorithm. These parameters are then predicted by the grey time series model. The two methods are applied to a gravity tank example. The case study demonstrates that the first method is more accurate for fault prediction.

Coupled dynamic model of state estimation for hypersonic glide vehicle

Aiming at handling complicated maneuvers or other unpredicted emergencies for hypersonic glide vehicle tracking,three coupled dynamic models of state estimation based on the priori information between guidance variables and aerodynamics are presented. Firstly, the aerodynamic acceleration acting on the target is analyzed to reveal the essence of the target’s motion.Then three coupled structures for modeling aerodynamic parameters are developed by different ideas: the spiral model with a harmonic oscillator, the bank model with trigonometric functions of the bank angle and the guide model with the changing rule of guidance variables. Meanwhile, the comparison discussion is concluded to show the novelty and advantage of these models.Finally, a performance assessment in different simulation cases is presented and detailed analysis is revealed. The results show that the proposed models perform excellent properties. Moreover, the guide model produces the best tracking performance and the bank model shows the second; however, the spiral model does not outperform the maneuvering reentry vehicle(MaRV) model markedly.

Dynamic Modeling and Three-Dimensional Motion Analysis of Underwater Gliders

For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.

A Dynamic Modeling For Cyclic Total Reflux Batch Distillation

Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batch distillation is proposed in this work,in which the changes in column holdup and liquid flow rate during the filling of the drum,and the consequent change in valid number of theoretical plates are considered.The effect of drum holdup on operation time is investigated and the optimal drum holdup is obtained from the simulation.The dynamic modeling is compared to the conventional modeling without consideration of change in liquid flow rate. The experimental result shows that the present modeling is more reliable and more accurate,especially for the column with large liquid holdup.

An improved dynamic model for a silicone material beam with large deformation

Dynamic modeling for incompressible hyperelastic materials with large deformation is an important issue in biomimetic applications. The previously proposed lower-order fully parameterized absolute nodal coordinate formulation（ANCF） beam element employs cubic interpolation in the longitudinal direction and linear interpolation in the transverse direction, whereas it cannot accurately describe the large bending deformation. On this account, a novel modeling method for studying the dynamic behavior of nonlinear materials is proposed in this paper. In this formulation, a higher-order beam element characterized by quadratic interpolation in the transverse directions is used in this investigation. Based on the Yeoh model and volumetric energy penalty function, the nonlinear elastic force matrices are derived within the ANCF framework. The feasibility and availability of the Yeoh model are verified through static experiment of nonlinear incompressible materials. Furthermore,dynamic simulation of a silicone cantilever beam under the gravity force is implemented to validate the superiority of the higher-order beam element. The simulation results obtained based on the Yeoh model by employing three different ANCF beam elements are compared with the result achieved from a commercial finite element package as the reference result. It is found that the results acquired utilizing a higher-order beam element are in good agreement with the reference results,while the results obtained using a lower-order beam element are different from the reference results. In addition, the stiffening problem caused by volumetric locking can be resolved effectively by applying a higher-order beam element. It is concluded that the proposed higher-order beam element formulation has satisfying accuracy in simulating dynamic motion process of the silicone beam.

Dynamic Modeling of a Roller Chain Drive System Considering the Flexibility of Input Shaft

Roller chain drives are widely used in various high-speed, high-load and power transmission applications, but their complex dynamic behavior is not well researched. Most studies were only focused on the analysis of the vibration of chain tight span, and in these models, many factors are neglected. In this paper, a mathematical model is developed to calculate the dynamic response of a roller chain drive working at constant or variable speed condition. In the model, the complete chain transmission with two sprockets and the necessary tight and slack spans is used. The effect of the flexibility of input shaft on dynamic response of the chain system is taken into account, as well as the elastic deformation in the chain, the inertial forces, the gravity and the torque on driven shaft. The nonlinear equations of movement are derived from using Lagrange equations and solved numerically. Given the center distance and the two initial position angles of teeth on driving and driven sprockets corresponding to the first seating roller on each side of the tight span, dynamics of any roller chain drive with two sprockets and two spans can be analyzed by the procedure. Finally, a numerical example is given and the validity of the procedure developed is demonstrated by analyzing the dynamic behavior of a typical roller chain drive. The model can well simulate the transverse and longitudinal vibration of the chain spans and the torsional vibration of the sprockets. This study can provide an effective method for the analysis of the dynamic characteristics of all the chain drive systems.

A nitrogen and phosphorus dynamic model of mesocosm pelagic ecosystem in the Jiaozhou Bay in China

A nitrogen and phosphorus dynamic model of mesocosm pelagic ecosystem was established according to the summary and synthesis of the models available, in which seven state variables （DIN, PO4-P, DON, DOP, phytoplankton, zooplankton and detritus） were included. Logically it had five modules--phytoplankton, zooplankton, dissolved inorganic nutrients, dissolved organic nutrients and detritus. The results showed that this model could simulate the variations of DIN, PO4-P, DON, DOP, POC and phytoplankton biomass in pelagic ecosystem in mesocosm properly, based on the site experiment data in the Jiaozhou Bay in the autumn of 1999 and the summer of 2000. Not only the logical structure but also the model parameters were feasible, and about 20 parameters were made to fit for the Jiaozhou Bay during the simulation. All of these are necessary to study the control mechanism of nutrients biogeochemical cycling in the Jiaozhou Bay and other China＇ s coastal waters.

Dynamic Modeling and Experiment of a New Type of Parallel Servo Press Considering Gravity Counterbalance

The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.

Dynamic modeling of a parafoil system considering flap deflection

In order to better study the dynamic characteristics and the control strategy of parafoil systems,considering the effect of flap deflection as the control mechanism and regarding the parafoil and the payload as a rigid body,a six degrees-of-freedom(DOF)dynamic model of a parafoil system including three DOF for translational motion and three DOF for rotational motion,is established according to the K rchhoff motion equation.Since the flexible winged paafoil system flying at low altitude is more susceptibleto winds,the motion characteristics of the parafoil system Wth and Wthout winds are simulated and analyzed.Furthermore,the ardropm test is used to further verify the model.The comparison results show that the simulation trajectory roughly overlaps with the actual flight track.The horzontnl velocity of the simulation model is in good accordance with the airdrop test,with a deviation less than0.5m/s,while its simulated vertical velocity fuctuates slightly under the infuence of the wind,and shows a similar trend to the ardrop test.It is concludedthat the established model can well describe the characteristics of the parafoil system.

Dynamic Modeling and Analysis of 9-DOF Omnidirectional Legged Vehicle

The omnidirectional legged vehicle with steering-rails has a specific mechanism feature, and it can be controlled flexibly and accurately in omnidirectional motion. Currently there lacks further research in this area. In this paper, the mechanical characteristics of independent walking control and steering control and its kinematics principle are introduced, and a vehicle has a composite motion mode of parallel link mechanism and steering mechanism is presented. The motion direction control of the proposed vehicle is only dependant on its steering rails, so its motion is simple and effective to control. When the relative motion between the walking and steering is controlled cooperatively, the vehicle can walk perfectly. By controlling the steering rails, the vehicle can walk along arbitrary trajectory on the ground. To achieve a good result of motion control, an equivalent manipulator model needs to be built. In terms of the mechanism feature and the kinematic principle, the simplified manipulator model consists of a rail in stance phase, a rail in swing phase, and an equivalent leg. Considering the ground surface slope during walking, a parameter of inclination angle is added. Based on such a RPP manipulator model, the equations of motion are derived by means of Lagrangian dynamic approach. To verify the dynamic equations, the motion of the manipulator model is simulated based on linear and nonlinear motion planning. With the same model and motion parameters, the dynamic equations can be solved by Matlab and the calculation data can be gained. Compared with the simulation data, the result confirms the manipulator dynamic equations are correct. As a result of such special characteristics of the legged mechanism with steering rails, it has a potential broad application prospects. The derivation of dynamics equation could benefit the motion control of the mechanism.

Dynamic Modeling and Eigenvalue Evaluation of a 3-DOF PKM Module

Due to the structural complexity, the dynamic modeling and quick performance evaluation for the parallel kinematic machines （PKMs） are still to be remained as two challenges in the stage of conceptual design. By using the finite element method and substructure synthesis, this paper mainly deals with the dynamic modeling and eigenvalue evaluation of a novel 3-DOF spindle head named the A3 head. The topological architecture behind the proposed A3 head is a 3-RPS parallel mechanism, which possesses one translational and two rotational capabilities. The mechanical features of the A3 head are briefly addressed in the first place followed by inverse position analysis. In the dynamic modeling, the platform is treated as a rigid body, the RPS limbs as the continuous uniform beams and the joints as lumped virtual springs. With the combination of substructure synthesis and finite element method, an analytical approach is then proposed to formulate the governing equations of motion of system using the compatibility conditions at interface between the limbs and the platform. Consequently, by solving the eigenvalue problem of the governing equations of motion, the distribution of lower natural frequencies of the A3 head throughout the entire workspace can be predicted in a quick manner. Modal analysis for the A3 head reveals that the distributions of lower natural frequencies are strongly related to the mechanism configuration and are axially symmetric due to system kinematic and structural features. The sensitivity analysis of the system indicates that the dimensional parameters of the 3-RPS mechanism have a slight effect on system lower natural frequencies while the joint compliances affect the distributions of lower natural frequencies significantly. The proposed dynamic modeling method can also be applied to other PKMs and can effectively evaluate the PKM＇s dynamic performance throughout the entire workspace.

Dynamic Modeling and Simulation of a Commercial Naphtha Catalytic Reforming Process

A first principles-based dynamic model for a continuous catalyst regeneration (CCR) platforming process, the UOP commercial naphtha catalytic reforming process, is developed in this paper. The lumping details of the naphtha feed and reaction scheme of the reaction model are given. The process model is composed of the reforming reaction model with catalyst deactivation, the furnace model and the separator model, which is capable of capturing the major dynamics that occurs in this process system. Dynamic simulations are performed based on Gear numerical algorithm and method of lines (MOL), a numerical technique dealing with partial differential equations (PDEs). The results of simulation are also presented. Dynamic responses caused by disturbances in the process system can be correctly predicted through simulations.

Basin-and Mountain-Building Dynamic Model of “Ramping-Detachment-Compression” in the West Kunlun-Southern Tarim Basin Margin

Analysis of the deformation structures in the West Kunlun-Tarim basin-range junction belt indicates that sediments in the southwestern Tarim depression were mainly derived from the West Kunlun Mountains and that with time the region of sedimentation extended progressivdy toward the north. Three north-underthrusting （subducting）, steep-dipping, high-velocity zones （bodies） are recognized at depths, which correspond to the central West Kunlun junction belt （bounded by the Kiida-Kaxtax fault on the north and Bulungkol-Kangxiwar fault on the south）, Quanshuigou fault belt （whose eastward extension is the Jinshajiang fault belt） and Bangong Co-Nujiang fault belt. The geodynamic process of the basin-range junction belt generally proceeded as follows： centering around the magma source region （which largely corresponds with the Karatag terrane at the surface）, the deep-seated material flowed and extended from below upward and to all sides, resulting in strong deformation （mainly extension） in the overlying lithosphere and even the upper mantle, appearance of extensional stress perpendicular to the strike of the orogenic belt in the thermal uplift region or at the top of the mantle diapir and localized thickening of the sedimentary cover （thermal subsidence in the upper crust）. Three stages of the basin- and mountain-forming processes in the West Kunlun-southern Tarim basin margin may be summarized： （1） the stage of Late Jurassic-Early Cretaceous rampingrapid uplift and rapid subsidence, when north-directed thrust propagation and south-directed intracontinental subduction, was the dominant mechanism for basin- and mountain-building processes; （2） the stage of Late Cretaceous-Paleogene deep-level detachment-slow uplift and homogeneous subsidence, when the dominant mechanism for the basin- and mountain-forming processes was detachment （subhorizontal north-directed deep-level ductile shear） and its resulting lateral propagation of deep material; and （3） the stage of Neogene-present compression-rapid uplift and strong subsidence, when the basin- and mountain-forming processes were simultaneously controlled by north-vergent thrust propagation and compression. The authors summarize the processes as the “ramping-detachment-compression basin- and mountain-forming dynamic model”. The basin-range tectonics was initiated in the Late Jurassic, the Miocene-Pliocene were a major transition period for the basin- and mountain-forming mechanism and the terminal early Pleistocene tectonic movement in the main laid a foundation for the basin-and-mountain tectonic framework in the West Kunlun-southern Tarim basin margin.

Roll System and Stock's Multi-parameter Coupling Dynamic Modeling Based on the Shape Control of Steel Strip

The existence of rolling deformation area in the rolling mill system is the main characteristic which dis- tinguishes the other machinery. In order to analyze the dynamic property of roll system＇s flexural deformation, it is necessary to consider the transverse periodic movement of stock in the rolling deformation area which is caused by the flexural deformation movement of roll system simul- taneously. Therefore, the displacement field of roll system and flow of metal in the deformation area is described by kinematic analysis in the dynamic system. Through intro- ducing the lateral displacement function of metal in the deformation area, the dynamic variation of per unit width rolling force can be determined at the same time. Then the coupling law caused by the co-effect of rigid movement and flexural deformation of the system structural elements is determined. Furthermore, a multi-parameter coupling dynamic model of the roll system and stock is established by the principle of virtual work. More explicitly, the cou- pled motion modal analysis was made for the roll system. Meanwhile, the analytical solutions for the flexural defor- mation movement＇s mode shape functions of rolls are discussed. In addition, the dynamic characteristic of the lateral flow of metal in the rolling deformation area has been analyzed at the same time. The establishment ofdynamic lateral displacement function of metal in the deformation area makes the foundation for analyzing the coupling law between roll system and rolling deformation area, and provides a theoretical basis for the realization of the dynamic shape control of steel strip.

A Dynamic Model for Simulating Atmospheric, Surface and Soil Water interactions in Hillslope of Loess Area Under Natural Conditions and Its Application

The mechanism of atmospheric, surface and soil water interactions (water transformation) in hillslope under natural conditions was analyzed, and a dynamic model was developed to simulate infiltration, overland flow and soil water movement during natural rainfall in hillslope, by bringing forward concepts such. as rainfall intensity on slope and a correction coefficient of saturated soil water content for soil surface seal. Some factors, including slope angle, slope orientation and raindrop inclination, which affect the rainfall amount on slope, were taken into account while developing the dynamic model. The effect of surface seal on infiltration and water balance under a boundary condition of the second kind was also considered. Application of the model in a field experiment showed that the model simulated precisely the infiltration, overland flow and soil water movement in hillslope under natural rainfall conditions.