Dynamic Response of A Group of Cylindrical Storage Tanks with Baffles Considering the Effect of Soil Foundation

The sloshing in a group of rigid cylindrical tanks with baffles and on soil foundation under horizontal excitation is studied analytically.The solutions for the velocity potential are derived out by the liquid subdomain method.Equivalent models with mass-spring oscillators are established to replace continuous fluid.Combined with the least square technique,Chebyshev polynomials are employed to fit horizontal,rocking and horizontal-rocking coupling impedances of soil,respectively.A lumped parameter model for impedance is presented to describe the effects of soil on tank structures.A mechanical model for the soil-foundation-tank-liquid-baffle system with small amount of calculation and high accuracy is proposed using the substructure technique.The analytical solutions are in comparison with data from reported literature and numerical codes to validate the effectiveness and correctness of the model.Detailed dynamic properties and seismic responses of the soil-tank system are given for the baffle number,size and location as well as soil parameter.

Stability analysis of CO_(2)gas shielded welding short-circuit transition process based on GMAW dynamic model

Base on the arc phase and short-circuit phase and their relationship, the paper considers the changes of the extension of wire, the arc length, liquid bridge resistance and mass of liquid bridge, combines the improved “mass-spring” model with the loop model of welding power system, puts forward the critical judgment condition of droplet transition, and establishes a more accurate dynamic model for describing the short-circuit transition process. The dynamic changes of short-circuit transfer frequency, welding current and voltage, contact droplet and residual droplet equivalent radius and droplet equivalent radius at different wire feeding speeds were calculated and analyzed, and compared with the experimental results. It shows that the fluctuation of droplet displacement, velocity and wire extension length at the optimal arc starting point is the smallest. The smaller the initial liquid bridge curvature radius is, the better the stability of short-circuit transfer is.

The initial stages of Li_(2)O_(2) formation during oxygen reduction reaction in Li-O_(2) batteries:The significance of Li_(2)O_(2) in charge-transfer reactions within devices

Lithium-oxygen batteries are a promising technology because they can greatly surpass the energy density of lithium-ion batteries.However,this theoretical characteristic has not yet been converted into a real device with high cyclability.Problems with air contamination,metallic lithium reactivity,and complex discharge and charge reactions are the main issues for this technology.A fast and reversible oxygen reduction reaction(ORR)is crucial for good performance of secondary batteries',but the partial knowledge of its mechanisms,especially when devices are concerned,hinders further development.From this perspective,the present work uses operando Raman experiments and electrochemical impedance spectroscopy(EIS)to assess the first stages of the discharge processes in porous carbon electrodes,following their changes cycle by cycle at initial operation.A growth kinetic formation of the discharge product signal(Li_(2)O_(2))was observed with operando Raman,indicating a first-order reaction and enabling an analysis by a microkinetic model.The solution mechanism in the evaluated system was ascribed for an equivalent circuit with three time constants.While the time constant for the anode interface reveals to remain relatively constant after the first discharge,its surface seemed to be more non-uniform.The model indicated that the reaction occurs at the Li_(2)O_(2) surface,decreasing the associated resistance during the initial discharge phase.Furthermore,the growth of Li_(2)O_(2) forms a hetero-phase between Li_(2)O_(2)/electrolyte,while creating a more compact and homogeneous on the Li_(2)O_(2)/cathode surface.The methodology here described thus offers a way of directly probing changes in surface chemistry evolution during cycling from a device through EIS analysis.

Small-Signal Equivalent Circuit Modeling of a Photodetector Chip

A small-signal equivalent circuit model and the ted. The equivalent lumped circuit, which takes the main extraction techniques for photodetector chips are presen- factors that limit a photodetector＇s RF performance into consideration,is first determined based on the device＇s physical structure. The photodetector＇s S parameters are then on-wafer measured, and the measured raw data are processed with further calibration. A genetic algorithm is used to fit the measured data, thereby allowing us to calculate each parameter value of the model. Experimental resuits show that the modeled parameters are well matched to the measurements in a frequency range from 130MHz to 20GHz, and the proposed method is proved feasible. This model can give an exact description of the photodetector chip＇s high frequency performance,which enables an effective circuit-level prediction for photodetector and optoelectronic integrated circuits.

Dynamic modeling and analysis of the closed-circuit grinding-classification process

Mathematical models of the grinding process are the basis of analysis, simulation and control. Most existent models in- cluding theoretical models and identification models are, however, inconvenient for direct analysis. In addition, many models pay much attention to the local details in the closed-circuit grinding process while overlooking the systematic behavior of the process as a whole. From the systematic perspective, the dynamic behavior of the whole closed-circuit grinding-classification process is consid- ered and a first-order transfer function model describing the dynamic relation between the raw material and the product is established. The model proves that the time constant of the closed-circuit process is lager than that of the open-circuit process and reveals how physical parameters affect the process dynamic behavior. These are very helpful to understand, design and control the closed-circuit grinding-classification process.

Simulation of second-order RC equivalent circuit model of lithium battery based on variable resistance and capacitance

With the rise of the electric vehicle industry,as the power source of electric vehicles,lithium battery has become a research hotspot.The state of charge(SOC)estimation and modelling of lithium battery are studied in this paper.The ampere-hour(Ah)integration method based on external characteristics is analyzed,and the open-circuit voltage(OCV)method is studied.The two methods are combined to estimate SOC.Considering the accuracy and complexity of the model,the second-order RC equivalent circuit model of lithium battery is selected.Pulse discharge and exponential fitting of lithium battery are used to obtain corresponding parameters.The simulation is carried out by using fixed resistance capacitance and variable resistance capacitor respectively.The accuracy of variable resistance and capacitance model is 2.9%,which verifies the validity of the proposed model.

Mapping equivalent approach to analysis and realization of memristor-based dynamical circuit

A novel mapping equivalent approach is proposed in this paper, which can be used for analyzing and realizing a memristor-based dynamical circuit equivalently by a nonlinear dynamical circuit with the same topologies and circuit parameters. A memristor-based chaotic circuit and the corresponding Chua＇s chaotic circuit with two output differentiators are taken as examples to illustrate this approach. Equivalent dynamical analysis and realization of the memristor-based chaotic circuit are performed by using Chua＇s chaotic circuit. The results indicate that the outputs of memristor-based chaotic circuit and the corresponding outputs of Chua＇s chaotic circuit have identical dynamics. The proposed approach verified by numerical simulations and experimental observations is useful in designing and analyzing memristor-based dynamical circuits.

An equivalent model of discharge instability in the discharge chamber of Kaufman ion thruster

The industrial application of the Kaufman ion thruster in its arc stage is limited owing to the instability of the discharge pulse.Presently,a complete prediction model that can predict the discharge pulse in the high-current stage does not exist.In this study,a complete prediction model for the pulse in the ion thruster is established using the zero-dimensional plasma discharge model and equivalent circuit model.The zero-dimensional plasma discharge model is used to obtain the corresponding plasma parameters by calculating the beam current,discharge current,voltage,and gas flow under actual working conditions.The input parameters of the equivalent circuit model are calculated using empirical formulae to acquire the estimated discharge waveforms.The pulse waveforms obtained using the model are found to be consistent with the experimental results.The model is used to evaluate the process of rapid changes in plasma density.Additionally,this model is employed to predict changes in the pulse waveforms when the volume of the discharge chamber and grid plate transmittance are changed.

Analysis for Transmission of Composite Structure with Graphene Using Equivalent Circuit Model

A simple analytical method is presented to analyze the transmission of electromagnetic plane waves through multilayer stacked composite two-dimensional( 2D) structures at microwave frequencies. Unlike the traditional structure,high impedance surface with graphene sheet is proposed. The structure includes graphene and thin metal patches and meshes. Simple analytical formulas are introduced for the surface impedance of graphene and for the grid impedance of electrically dense arrays of metal square patches or strips. The result of transmission properties is based on the dynamic tunable model of the high impedance surface,which considers the surface conductivity of graphene layer. The transmission coefficient obtained by using the equivalent circuit method is validated against full-wave numerical simulations. The considered equivalent circuit method can be useful in the design of graphene tunable planar devices.

Extrinsic equivalent circuit modeling of InP HEMTs based on full-wave electromagnetic simulation

With the widespread utilization of indium-phosphide-based high-electron-mobility transistors(InP HEMTs)in the millimeter-wave(mmW)band,the distributed and high-frequency parasitic coupling behavior of the device is particularly prominent.We present an InP HEMT extrinsic parasitic equivalent circuit,in which the conductance between the device electrodes and a new gate-drain mutual inductance term L_(mgd)are taken into account for the high-frequency magnetic field coupling between device electrodes.Based on the suggested parasitic equivalent circuit,through HFSS and advanced design system(ADS)co-simulation,the equivalent circuit parameters are directly extracted in the multi-step system.The HFSS simulation prediction,measurement data,and modeled frequency response are compared with each other to verify the feasibility of the extraction method and the accuracy of the equivalent circuit.The proposed model demonstrates the distributed and radio-frequency behavior of the device and solves the problem that the equivalent circuit parameters of the conventional InP HEMTs device are limited by the device model and inaccurate at high frequencies when being extracted.

Design and Realization of CPW Circuits Using EC-ANN Models for CPW Discontinuities

Novel accurate and efficient equivalent circuit trained artificial neural-network （EC-ANN） models,which inherit and improve upon EC model and EM-ANN models＇ advantages,are developed for coplanar waveguide （CPW） discontinuities. Modeled discontinuities include ： CPW step, interdigital capacitor, symmetric cross junction, and spiral inductor, for which validation tests are performed. These models allow for circuit design, simulation, and optimization within a CAD simulator. Design and realization of a coplanar lumped element band pass filter on GaAs using the developed CPW EC-ANN models are demonstrated.

Chaotic memristive circuit:equivalent circuit realization and dynamical analysis

In this paper, a practical equivalent circuit of an active flux-controlled memristor characterized by smooth piecewise-quadratic nonlinearity is designed and an experimental chaotic memristive circuit is implemented. The chaotic memristive circuit has an equilibrium set and its stability is dependent on the initial state of the memristor. The initial state-dependent and the circuit parameter-dependent dynamics of the chaotic memristive circuit are investigated via phase portraits, bifurcation diagrams and Lyapunov exponents. Both experimental and simulation results validate the proposed equivalent circuit realization of the active flux-controlled memristor.

Transfer function modeling and analysis of the open-loop Buck converter using the fractional calculus

Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous conduction mode（CCM） operation are carried out in this paper.The fractional order small signal model and the corresponding equivalent circuit of the open-loop Buck converter in a CCM operation are presented.The transfer functions from the input voltage to the output voltage,from the input voltage to the inductor current,from the duty cycle to the output voltage,from the duty cycle to the inductor current,and the output impedance of the open-loop Buck converter in CCM operation are derived,and their bode diagrams and step responses are calculated,respectively.It is found that all the derived fractional order transfer functions of the system are influenced by the fractional orders of the inductor and the capacitor.Finally,the realization of the fractional order inductor and the fractional order capacitor is designed,and the corresponding PSIM circuit simulation results of the open-loop Buck converter in CCM operation are given to confirm the correctness of the derivations and the theoretical analysis.

Online Identification of Lithium-ion Battery Model Parameters with Initial Value Uncertainty and Measurement Noise

Online parameter identification is essential for the accuracy of the battery equivalent circuit model(ECM).The traditional recursive least squares(RLS)method is easily biased with the noise disturbances from sensors,which degrades the modeling accuracy in practice.Meanwhile,the recursive total least squares(RTLS)method can deal with the noise interferences,but the parameter slowly converges to the reference with initial value uncertainty.To alleviate the above issues,this paper proposes a co-estimation framework utilizing the advantages of RLS and RTLS for a higher parameter identification performance of the battery ECM.RLS converges quickly by updating the parameters along the gradient of the cost function.RTLS is applied to attenuate the noise effect once the parameters have converged.Both simulation and experimental results prove that the proposed method has good accuracy,a fast convergence rate,and also robustness against noise corruption.

An equivalent circuit model for terahertz quantum cascade lasers:Modeling and experiments

Terahertz quantum cascade lasers（THz QCLs） emitted at 4.4 THz are fabricated and characterized. An equivalent circuit model is established based on the five-level rate equations to describe their characteristics. In order to illustrate the capability of the model, the steady and dynamic performances of the fabricated THz QCLs are simulated by the model.Compared to the sophisticated numerical methods, the presented model has advantages of fast calculation and good compatibility with circuit simulation for system-level designs and optimizations. The validity of the model is verified by the experimental and numerical results.

ESTABLISHMENT AND VERIFICATION OF MATHEMATICAL MODEL FOR CURRENT LEAKAGE IN BIPOLAR MULTI－COMPARTMENT CELL

ＥＳＴＡＢＬＩＳＨＭＥＮＴＡＮＤＶＥＲＩＦＩＣＡＴＩＯＮＯＦＭＡＴＨＥＭＡＴＩＣＡＬＭＯＤＥＬＦＯＲＣＵＲＲＥＮＴＬＥＡＫＡＧＥＩＮＢＩＰＯＬＡＲＭＵＬＴＩ－ＣＯＭＰＡＲＴＭＥＮＴＣＥＬＬＹａｎｇ；ＪｉａｎｈｏｎｇＺｈａｎｇ；ＱｉｎｇｘｉａｎｇＷａｎ...

Logic Picture-Based Dynamic Power Estimation for Unit Gate-Delay Model CMOS Circuits

In this research, a fast methodology to calculate the exact value of the average dynamic power consumption for CMOS combinational logic circuits is developed. The delay model used is the unit-delay model where all gates have the same propagation delay. The main advantages of this method over other techniques are its accuracy, as it is deterministic and it requires less computational effort compared to exhaustive simulation approaches. The methodology uses the Logic Pictures concept for obtaining the nodes’ toggle rates. The proposed method is applied to well-known circuits and the results are compared to exhaustive simulation and Monte Carlosimulation methods.

Design and Verification of Equivalent Circuit for Cable Electrostatic Discharge

In the process of production, transportation and assembly, cable assemblies can get a lot of electrostatic charge by friction, dragging, pulling and induction. These residual charges can be discharged when Electrostatic sensitive device connected with it and can cause the complete failure or potential failure of the electrostatic sensitive product. In this paper, the theoretical model of cable assemblies is established by analyzing the characteristics of cable assemblies, and the equivalent RF circuit is designed. The static discharge characteristics of the cable are analyzed and verified by simulation.

SPICE model of trench-gate MOSFET device

A novel simulation program with an integrated circuit emphasis（SPICE） model developed for trench-gate metal-oxide-semiconductor field-effect transistor（M OSFET）devices is proposed. The drift region resistance was modeled according to the physical characteristics and the specific structure of the trench-gate MOSFET device. For the accurate simulation of dynamic characteristics, three important capacitances, gate-to-drain capacitance Cgd, gate-to-source capacitance Cgsand drain-to-source capacitance Cds, were modeled, respectively, in the proposed model. Furthermore,the self-heating effect, temperature effect and breakdown characteristic were taken into account; the self-heating model and breakdown model were built in the proposed model; and the temperature parameters of the model were revised. The proposed model is verified by experimental results, and the errors between measured data and simulation results of the novel model are less than 5%. Therefore, the model can give an accurate description for both the static and dynamic characteristics of the trench-gate MOSFET device.

COMPARISON BETWEEN TWO ANALYTICAL MODELS OF HELICOPTER GROUND RESONANCE

The 2-dimensional equivalent model used in helicopter ground resonance analysis is convenient for its simplicity and clarity. The equivalent body mass, the stiffness and the damping are derived from the modal charaCteristics. In this paper, a 3-dimensional space model is constructed to analyse the ground resonance.There is little difference between the calculated results of the 2-dimensional equivalent model and those of the 3-dimensional space model. Hence, the 2-dimensional model is verified for the practical application. Generally, the linear lead-lag damping of the equivalent rotor blade at the modal frequency is derived from the lead-lag damper characteristics by a procedure of iteration. The transformation of the imaginary part of the complex modulus of the viscoelastic damper into a linear velocity damping is complicated in analysis. A method to use the complex modulus directly in the ground resonance analysis is derived and verified.