Robust interface and excellent as-built mechanical properties of Ti–6Al–4V fabricated through laser-aided additive manufacturing with powder and wire

The feasibility of manufacturing Ti-6Al-4V samples through a combination of laser-aided additive manufacturing with powder(LAAM_(p))and wire(LAAM_(w))was explored.A process study was first conducted to successfully circumvent defects in Ti-6Al-4V deposits for LAAM_(p) and LAAM_(w),respectively.With the optimized process parameters,robust interfaces were achieved between powder/wire deposits and the forged substrate,as well as between powder and wire deposits.Microstructure characterization results revealed the epitaxial prior β grains in the deposited Ti-6Al-4V,wherein the powder deposit was dominated by a finerα′microstructure and the wire deposit was characterized by lamellar α phases.The mechanisms of microstructure formation and correlation with mechanical behavior were analyzed and discussed.The mechanical properties of the interfacial samples can meet the requirements of the relevant Aerospace Material Specifications(AMS 6932)even without post heat treatment.No fracture occurred within the interfacial area,further suggesting the robust interface.The findings of this study highlighted the feasibility of combining LAAM_(p) and LAAM_(w) in the direct manufacturing of Ti-6Al-4V parts in accordance with the required dimensional resolution and deposition rate,together with sound strength and ductility balance in the as-built condition.

A facile strategy for tuning the density of surface-grafted biomolecules for melt extrusion-based additive manufacturing applications

Melt extrusion-based additive manufacturing(ME-AM)is a promising technique to fabricate porous scaffolds for tissue engi-neering applications.However,most synthetic semicrystalline polymers do not possess the intrinsic biological activity required to control cell fate.Grafting of biomolecules on polymeric surfaces of AM scaffolds enhances the bioactivity of a construct;however,there are limited strategies available to control the surface density.Here,we report a strategy to tune the surface density of bioactive groups by blending a low molecular weight poly(ε-caprolactone)5k(PCL5k)containing orthogonally reactive azide groups with an unfunctionalized high molecular weight PCL75k at different ratios.Stable porous three-dimensional(3D)scaf-folds were then fabricated using a high weight percentage(75 wt.%)of the low molecular weight PCL 5k.As a proof-of-concept test,we prepared films of three different mass ratios of low and high molecular weight polymers with a thermopress and reacted with an alkynated fluorescent model compound on the surface,yielding a density of 201-561 pmol/cm^(2).Subsequently,a bone morphogenetic protein 2(BMP-2)-derived peptide was grafted onto the films comprising different blend compositions,and the effect of peptide surface density on the osteogenic differentiation of human mesenchymal stromal cells(hMSCs)was assessed.After two weeks of culturing in a basic medium,cells expressed higher levels of BMP receptor II(BMPRII)on films with the conjugated peptide.In addition,we found that alkaline phosphatase activity was only significantly enhanced on films contain-ing the highest peptide density(i.e.,561 pmol/cm^(2)),indicating the importance of the surface density.Taken together,these results emphasize that the density of surface peptides on cell differentiation must be considered at the cell-material interface.Moreover,we have presented a viable strategy for ME-AM community that desires to tune the bulk and surface functionality via blending of(modified)polymers.Furthermore,the use of alkyne-azide“click”chemistry enables spatial control over bioconjugation of many tissue-specific moieties,making this approach a versatile strategy for tissue engineering applications.

Performance-control-orientated hybrid metal additive manufacturing technologies:state of the art,challenges,and future trends

Metal additive manufacturing(AM)technologies have made significant progress in the basic theoretical field since their invention in the 1970s.However,performance instability during continuous processing,such as thermal history,residual stress accumulation,and columnar grain epitaxial growth,consistently hinders their broad application in standardized industrial production.To overcome these challenges,performance-control-oriented hybrid AM(HAM)technologies have been introduced.These technologies,by leveraging external auxiliary processes,aim to regulate microstructural evolution and mechanical properties during metal AM.This paper provides a systematic and detailed review of performance-control-oriented HAM technology,which is categorized into two main groups:energy field-assisted AM(EFed AM,e.g.ultrasonic,electromagnetic,and heat)technologies and interlayer plastic deformation-assisted AM(IPDed AM,e.g.laser shock peening,rolling,ultrasonic peening,and friction stir process)technologies.This review covers the influence of external energy fields on the melting,flow,and solidification behavior of materials,and the regulatory effects of interlayer plastic deformation on grain refinement,nucleation,and recrystallization.Furthermore,the role of performance-control-oriented HAM technologies in managing residual stress conversion,metallurgical defect closure,mechanical property improvement,and anisotropy regulation is thoroughly reviewed and discussed.The review concludes with an analysis of future development trends in EFed AM and IPDed AM technologies.

e-Manufacturing的体系结构和实施方案研究

e-Manufacturing即电子化制造是当前环境下产生的一种新的制造模式。介绍了e-Manufacturing的基本概念和基于此思想的企业集成框架 ,提出了e -Manufacturing的系统体系结构以及e-Manufacturing系统制造层的体系结构。在此基础上 ,针对各功能子系统的集成这一关键问题 ,给出了e -Manufacturing系统集成的一种面向服务的解决方案。该方案能充分利用企业现有应用系统 ,对它们进行统一的封装 ,并通过服务的方式将它们紧密集成 。

Manufacturing Development Emphases on Power Generation and Transmission Apparatus in 11th Five-Year Plan Period and Prospect to the Year 2020

Based on predictions on Chinese power development in the coming 20 years, this paper introduces the emphases and key technologies in power sources and power network construction, and puts for ward the major tasks and technological orientation for machinery manufacturers to supply qualified equipment to China power industry.

一个实现工厂底层数据采集的e-Manufacturing原型系统的研究

通过构建一个e-Manufacturing原型系统,阐述了它的一些核心概念,提出了它的体系结构模型及节点概念,并主要从实现技术的角度介绍了底层设备数据采集系统与上层ERP(Hmis)系统的集成,研究了其所涉及的关键技术的实现,原型系统经实际运行表明,网络客户端可以利用客户机、移动终端设备和网络摄像机,对现场设备进行远程实时数据采集、可视化的控制,实现了底层设备与上层应用系统之间信息的自动流动。

Additive manufacturing of micropatterned functional surfaces:a review

Over the course of millions of years,nature has evolved to ensure survival and presents us with a myriad of functional surfaces and structures that can boast high efficiency,multifunctionality,and sustainability.What makes these surfaces particularly practical and effective is the intricate micropatterning that enables selective interactions with microstructures.Most of these structures have been realized in the laboratory environment using numerous fabrication techniques by tailoring specific surface properties.Of the available manufacturing methods,additive manufacturing(AM)has created opportunities for fabricating these structures as the complex architectures of the naturally occurring microstructures far exceed the traditional ways.This paper presents a concise overview of the fundamentals of such patterned microstructured surfaces,their fabrication techniques,and diverse applications.A comprehensive evaluation of micro fabrication methods is conducted,delving into their respective strengths and limitations.Greater emphasis is placed on AM processes like inkjet printing and micro digital light projection printing due to the intrinsic advantages of these processes to additively fabricate high resolution structures with high fidelity and precision.The paper explores the various advancements in these processes in relation to their use in microfabrication and also presents the recent trends in applications like the fabrication of microlens arrays,microneedles,and tissue scaffolds.

Advances and challenges in direct additive manufacturing of dense ceramic oxides

Ceramic oxides,renowned for their exceptional combination of mechanical,thermal,and chemical properties,are indispensable in numerous crucial applications across diverse engineering fields.However,conventional manufacturing methods frequently grapple with limitations,such as challenges in shaping intricate geometries,extended processing durations,elevated porosity,and substantial shrinkage deformations.Direct additive manufacturing(dAM)technology stands out as a state-of-the-art solution for ceramic oxides production.It facilitates the one-step fabrication of high-performance,intricately designed components characterized by dense structures.Importantly,dAM eliminates the necessity for post-heat treatments,streamlining the manufacturing process and enhancing overall efficiency.This study undertakes a comprehensive review of recent developments in dAM for ceramic oxides,with a specific emphasis on the laser powder bed fusion and laser directed energy deposition techniques.A thorough investigation is conducted into the shaping quality,microstructure,and properties of diverse ceramic oxides produced through dAM.Critical examination is given to key aspects including feedstock preparation,laser-material coupling,formation and control of defects,in-situ monitoring and simulation.This paper concludes by outlining future trends and potential breakthrough directions,taking into account current gaps in this rapidly evolving field.

Repositioning fertilizer manufacturing subsidies for improving food security and reducing greenhouse gas emissions in China

China removed fertilizer manufacturing subsidies from 2015 to 2018 to bolster market-oriented reforms and foster environmentally sustainable practices.However,the impact of this policy reform on food security and the environment remains inadequately evaluated.Moreover,although green and low-carbon technologies offer environmental advantages,their widespread adoption is hindered by prohibitively high costs.This study analyzes the impact of removing fertilizer manufacturing subsidies and explores the potential feasibility of redirecting fertilizer manufacturing subsidies to invest in the diffusion of these technologies.Utilizing the China Agricultural University Agri-food Systems model,we analyzed the potential for achieving mutually beneficial outcomes regarding food security and environmental sustainability.The findings indicate that removing fertilizer manufacturing subsidies has reduced greenhouse gas(GHG)emissions from agricultural activities by 3.88 million metric tons,with minimal impact on food production.Redirecting fertilizer manufacturing subsidies to invest in green and low-carbon technologies,including slow and controlled-release fertilizer,organic-inorganic compound fertilizers,and machine deep placement of fertilizer,emerges as a strategy to concurrently curtail GHG emissions,ensure food security,and secure robust economic returns.Finally,we propose a comprehensive set of government interventions,including subsidies,field guidance,and improved extension systems,to promote the widespread adoption of these technologies.

Recent innovations in laser additive manufacturing of titanium alloys

Titanium(Ti)alloys are widely used in high-tech fields like aerospace and biomedical engineering.Laser additive manufacturing(LAM),as an innovative technology,is the key driver for the development of Ti alloys.Despite the significant advancements in LAM of Ti alloys,there remain challenges that need further research and development efforts.To recap the potential of LAM high-performance Ti alloy,this article systematically reviews LAM Ti alloys with up-to-date information on process,materials,and properties.Several feasible solutions to advance LAM Ti alloys are reviewed,including intelligent process parameters optimization,LAM process innovation with auxiliary fields and novel Ti alloys customization for LAM.The auxiliary energy fields(e.g.thermal,acoustic,mechanical deformation and magnetic fields)can affect the melt pool dynamics and solidification behaviour during LAM of Ti alloys,altering microstructures and mechanical performances.Different kinds of novel Ti alloys customized for LAM,like peritecticα-Ti,eutectoid(α+β)-Ti,hybrid(α+β)-Ti,isomorphousβ-Ti and eutecticβ-Ti alloys are reviewed in detail.Furthermore,machine learning in accelerating the LAM process optimization and new materials development is also outlooked.This review summarizes the material properties and performance envelops and benchmarks the research achievements in LAM of Ti alloys.In addition,the perspectives and further trends in LAM of Ti alloys are also highlighted.

Toward understanding the microstructure characteristics,phase selection and magnetic properties of laser additive manufactured Nd-Fe-B permanent magnets

Nd-Fe-B permanent magnets play a crucial role in energy conversion and electronic devices.The essential magnetic properties of Nd-Fe-B magnets,particularly coercivity and remanent magnetization,are significantly infuenced by the phase characteristics and microstructure.In this work,Nd-Fe-B magnets were manufactured using vacuum induction melting(VIM),laser directed energy deposition(LDED)and laser powder bed fusion(LPBF)technologies.Themicrostructure evolution and phase selection of Nd-Fe-B magnets were then clarified in detail.The results indicated that the solidification velocity(V)and cooling rate(R)are key factors in the phase selection.In terms of the VIM-casting Nd-Fe-B magnet,a large volume fraction of theα-Fe soft magnetic phase(39.7 vol.%)and Nd2Fe17Bxmetastable phase(34.7 vol.%)areformed due to the low R(2.3×10-1?C s-1),whereas only a minor fraction of the Nd2Fe14B hard magnetic phase(5.15 vol.%)is presented.For the LDED-processed Nd-Fe-B deposit,although the Nd2Fe14B hard magnetic phase also had a low value(3.4 vol.%)as the values of V(<10-2m s-1)and R(5.06×103?C s-1)increased,part of theα-Fe soft magnetic phase(31.7vol.%)is suppressed,and a higher volume of Nd2Fe17Bxmetastable phases(47.5 vol.%)areformed.As a result,both the VIM-casting and LDED-processed Nd-Fe-B deposits exhibited poor magnetic properties.In contrast,employing the high values of V(>10-2m s-1)and R(1.45×106?C s-1)in the LPBF process resulted in the substantial formation of the Nd2Fe14B hard magnetic phase(55.8 vol.%)directly from the liquid,while theα-Fe soft magnetic phase and Nd2Fe17Bxmetastable phase precipitation are suppressed in the LPBF-processed Nd-Fe-B magnet.Additionally,crystallographic texture analysis reveals that the LPBF-processedNd-Fe-B magnets exhibit isotropic magnetic characteristics.Consequently,the LPBF-processed Nd-Fe-B deposit,exhibiting a coercivity of 656 k A m-1,remanence of 0.79 T and maximum energy product of 71.5 k J m-3,achieved an acceptable magnetic performance,comparable to other additive manufacturing processed Nd-Fe-B magnets from MQP(Nd-lean)Nd-Fe-Bpowder.

A review on the multi-scaled structures and mechanical/thermal properties of tool steels fabricated by laser powder bed fusion additive manufacturing

The laser powder bed fusion(LPBF) process can integrally form geometrically complex and high-performance metallic parts that have attracted much interest,especially in the molds industry.The appearance of the LPBF makes it possible to design and produce complex conformal cooling channel systems in molds.Thus,LPBF-processed tool steels have attracted more and more attention.The complex thermal history in the LPBF process makes the microstructural characteristics and properties different from those of conventional manufactured tool steels.This paper provides an overview of LPBF-processed tool steels by describing the physical phenomena,the microstructural characteristics,and the mechanical/thermal properties,including tensile properties,wear resistance,and thermal properties.The microstructural characteristics are presented through a multiscale perspective,ranging from densification,meso-structure,microstructure,substructure in grains,to nanoprecipitates.Finally,a summary of tool steels and their challenges and outlooks are introduced.

Research on Cloud Manufacturing Resource-Aware and Access Technology Using RFID

With the continuous development of cloud manufacturing technology,in order to solve more complex manufacturing problem and conduct large-scale networked manufacturing,combining with the characteristic of discrete manufacturing enterprise's demands and RFID( Radio Frequency Identification),a kind of RFIDbased cloud manufacturing resource-aware and access technology is proposed. Firstly,the architecture of the cloud manufacturing system and RFID system is briefly introduced. Then,the key technologies of manufacturing resource-aware and access technology are analyzed,including anti-collision technology,reader management technology and so on. Finally,taking the manufacturing of the key components in discrete manufacturing enterprise as an example,the practicality and feasibility of the technology is verified. The results show that the application of this technology provides a strong guarantee for the sharing and collaboration of manufacturing resources and capacity in the discrete manufacturing industry.

Advances in Compact Manufacturing for Shape and Performance Controllability of Large-scale Components-A Review

Research on compact manufacturing technology for shape and performance controllability of metallic components can reanze the simplification and high-reliability of manufacturing process on the premise of satisfying the requirement of macro/micro-structure. It is not only the key paths in improving performance, saving material and energy, and green manufacturing of components used in major equipments, but also the challenging subjects in frontiers of advanced plastic forming. To provide a novel horizon for the manufacturing in the critical components is significant. Focused on the high-performance large-scale components such as bearing rings, flanges, railway wheels, thick-walled pipes, etc, the conventional processes and their developing situations are summarized. The existing problems including multi-pass heating, wasting material and energy, high cost and high-emission are discussed, and the present study unable to meet the manufacturing in high-quality components is also pointed out. Thus, the new techniques related to casting-rolling compound precise forming of rings, compact manufacturing for duplex-metal composite rings, compact manufacturing for railway wheels, and casting-extruding continuous forming of thick-walled pipes are introduced in detail, respectively. The corresponding research contents, such as casting ring blank, hot ring rolling, near solid-state pressure forming, hot extruding, are elaborated. Some findings in through-thickness microstructure evolution and mechanical properties are also presented. The components produced by the new techniques are mainly characterized by fine and homogeneous grains. Moreover, the possible directions for fin＇ther development of those techniques are suggested. Finally, the key scientific problems are first proposed. All of these results and conclusions have reference value and guiding significance for the integrated control of shape and performance in advanced compact manufacturing.

Social Sensors (S^2ensors): A Kind of Hardware-Software-Integrated Mediators for Social Manufacturing Systems Under Mass Individualization

Currently, little work has been devoted to the mediators and tools for multi-role production interactions in the mass individualization environment. This paper proposes a kind of hardware-software-integrated mediators called social sensors （S2ensors） to facilitate the production interactions among customers, manufacturers, and other stakeholders in the social manufacturing systems （SMS）. The concept, classification, operational logics, and for- malization of S2ensors are clarified. S2ensors collect sub- jective data from physical sensors and objective data from sensory input in mobile Apps, merge them into meaningful information for decision-making, and finally feed the decisions back for reaction and execution. Then, an S2en- sors-Cloud platform is discussed to integrate different S2- ensors to work for SMSs in an autonomous way. A demonstrative case is studied by developing a prototype system and the results show that S2ensors and S2ensors- Cloud platform can assist multi-role stakeholders interact and collaborate for the production tasks. It reveals the mediator-enabled mechanisms and methods for production interactions among stakeholders in SMS.

Digital manufacturing of personalized magnesium implants through binder jet additive manufacturing and automated post machining

While magnesium(Mg)is a promising material for personalized temporary implants,the lack of a digital manufacturing solution for Mg implants impedes its potential progress.This study introduces a hybrid manufacturing process that integrates binder jet additive manufacturing with automated dry post-machining to enable end-to-end digital manufacturing of personalized Mg implants.Spherical cap-shaped Mg implants were additively manufactured through binder jetting.These implants were placed on graphite flakes during sintering as a potential non-reactive support material,allowing unrestricted shrinkage of 15.2%to a relative density of 87%.Microstructural and dimensional analysis revealed consistent interconnected porous microstructures with a shrinkage distortion within±0.2 mm of the original digital drawing.High-speed dry milling of the sintered samples,assessed via an orthogonal cutting test,identified the optimized cutting parameters.A three-step machining process for automated 5-axis machining,along with clamping strategies,referencing,and an adaptive plug-in,were successfully implemented.The automated dry machining on binder-jet printed Mg implants resulted in an average roughness of<1.3μm with no defects.In summary,this work introduces a robust digital manufacturing solution to advance the transformative landscape of Mg implants and scaffolds.©2024 Chongqing University.Publishing services provided by Elsevier B.V.on behalf of KeAi Communications Co.Ltd.

Fundamentals of atomic and close-to-atomic scale manufacturing:a review

Atomic and close-to-atomic scale manufacturing(ACSM)represents techniques for manufacturing high-end products in various fields,including future-generation computing,communication,energy,and medical devices and materials.In this paper,the theoretical boundary between ACSM and classical manufacturing is identified after a thorough discussion of quantum mechanics and their effects on manufacturing.The physical origins of atomic interactions and energy beams-matter interactions are revealed from the point view of quantum mechanics.The mechanisms that dominate several key ACSM processes are introduced,and a current numerical study on these processes is reviewed.A comparison of current ACSM processes is performed in terms of dominant interactions,representative processes,resolution and modelling methods.Future fundamental research is proposed for establishing new approaches for modelling ACSM,material selection or preparation and control of manufacturing tools and environments.This paper is by no means comprehensive but provides a starting point for further systematic investigation of ACSM fundamentals to support and accelerate its industrial scale implementation in the near future.

Additive manufacturing of magnesium and its alloys: process-formabilitymicrostructure-performance relationship and underlying mechanism

Magnesium and its alloys,as a promising class of materials,is popular in lightweight application and biomedical implants due to their low density and good biocompatibility.Additive manufacturing(AM)of Mg and its alloys is of growing interest in academia and industry.The domain-by-domain localized forming characteristics of AM leads to unique microstructures and performances of AM-process Mg and its alloys,which are different from those of traditionally manufactured counterparts.However,the intrinsic mechanisms still remain unclear and need to be in-depth explored.Therefore,this work aims to discuss and analyze the possible underlying mechanisms regarding defect appearance and elimination,microstructure formation and evolution,and performance improvement,based on presenting a comprehensive and systematic review on the relationship between process parameters,forming quality,microstructure characteristics and resultant performances.Lastly,some key perspectives requiring focus for further progression are highlighted to promote development of AM-processed Mg and its alloys and accelerate their industrialization.

Ballistic performance of additive manufacturing 316l stainless steel projectiles based on topology optimization method

Material and structure made by additive manufacturing(AM)have received much attention lately due to their flexibility and ability to customize complex structures.This study first implements multiple objective topology optimization simulations based on a projectile perforation model,and a new topologic projectile is obtained.Then two types of 316L stainless steel projectiles(the solid and the topology)are printed in a selective laser melt(SLM)machine to evaluate the penetration performance of the projectiles by the ballistic test.The experiment results show that the dimensionless specific kinetic energy value of topologic projectiles is higher than that of solid projectiles,indicating the better penetration ability of the topologic projectiles.Finally,microscopic studies(scanning electron microscope and X-ray micro-CT)are performed on the remaining projectiles to investigate the failure mechanism of the internal structure of the topologic projectiles.An explicit dynamics simulation was also performed,and the failure locations of the residual topologic projectiles were in good agreement with the experimental results,which can better guide the design of new projectiles combining AM and topology optimization in the future.

Atomic precision manufacturing of carbon nanotube-a perspective

Carbon nanotube(CNT),particularly single-walled CNT,possesses exceptional properties,and can be utilized in many high-end applications including high-performance electronics.However,the atomic arrangement of a CNT determines its band structure,making the atomic-precision fabrication one of most important topics for the development of this material.In this perspective,the author gives a personal summary on the history,current status of the atomic-precision fabrication of CNT and outlines the remaining challenges as well as the possible paths that may lead the production of atomically precise CNTs from‘fabrication’to‘manufacturing’.