Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes （PPMMs）. Attenuated total reflection-Fourier transform infrared spectroscopy （ATR/FT-IR） and field emission scanning electron microscope （FE- SEM） were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor （MBR）, filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.

FORMATION AND MICROSTRUCTURE OF POLYETHYLENE MICROPOROUS MEMBRANES THROUGH THERMALLY INDUCED PHASE SEPARATION

Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particular membrane, which depends on the diluent properties,polymer concentration and cooling rate, were observed by scanning electron microscopy.'Beehive-type,'leafy-like, and lacy porous structure morphologies can be formed,depending onthe blend composition and phase separation conditions, which were discussed by the polymer anddiluent crystallization processes.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-Pressure Plasma Immobilization of N,N-dimethylamino Ethyl Methacrylate

Surface modification of polypropylene microporous membrane （PPMM） was performed by atmospheric pressure dielectric barrier discharge plasma immobilization of N,Ndimethylamino ethyl methacrylate （DMAEMA）. Structural and morphological changes on the membrane surface were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Results reveal that both the plasma-treating conditions and the adsorbed DMAEMA amount have remarkable effects on the immobilization degree of DMAEMA. Peroxide determination by 1,1-diphenyl-2-picrvlhydrazyl （DPPH） method verifies the exsistence of radicals induced by plasma, which activize the immobilization reaction. Pure water contact angle on the membrane surface decreased with the increase of DMAEMA immobilization degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of immobilization degrees on pure water fluxes were also measured. It is shown that pure water fluxes first increased with immobilization degree and then decreased. Finally, permeation of bovine serum albumin （BSA） and lysozyme solution were measured to evaluate the antifouling property of the DMAEMA-modified membranes, from which it is shown that both hydrophilicity and electrostatic repulsion are beneficial for membrane antifouling.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANES BY THE ADSORPTION OF NON-IONIC SURFACTANTS

Surface modification by physical adsorption of a series of non-ionic surfactants including Tween 20, Tween 40, Tween 60, Tween 80 and Tween 85, was accomplished on polypropylene microporous hollow fiber and flat membranes. The adsorption curve of the membrane surface was analyzed by weight measurements and the typical results showed a twoplatform character similarly. Differences in the degree and curve shape of adsorption resulting from such factors as concentration, temperature, as well as water cleaning time were observed for Tween 85 among other Tweens. Attenuated total reflection - Fourier transform infrared spectroscopy analysis and field emission scanning electron microscopy observation showed that the adsorption of Tween on polypropylene microporous membrane （PPMM） is effective and occurs mainly in the pores of PPMMs at low adsorption amount, and on the membrane surface also at high adsorption value.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-pressure Plasma Induced N-vinyl-2-pyrrolidone Graft Polymerization

Membrane surfaces modified with poly（N-vinyl-2-pyrrolidone） （PNVP） can be endowed with hydrophilicity, biocompatibility and functionality. In this work, atmospheric pressure dielectric barrier discharge plasma graft polymerization of N-vinyl-2-pyrrolidone （NVP） onto polypropylene （PP） microporous membrane surface was studied. The experimental results reveal that plasma treatment conditions, such as discharge power, treatment time and adsorbed NVP amount, have remarkable effects on the grafting degree of NVP. Structural and morphological changes on the membrane surfaces were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Water contact angles on the membrane surfaces decrease with the increase of NVP grafting degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of grafting degrees on pure water fluxes were also measured. It is shown that pure water fluxes increase with grafting degree firstly and then decrease adversely. Finally, filtration of bovine serum albumin （BSA） solution and platelets adhesion of the PNVP modified membranes show good protein resistance and potential biocompatibility due to the enhancement of surface hydrophilicity.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANE BY TETHERING POLYPEPTIDES

Two kinds of polypeptides were tethered onto the surface of polypropylene microporous membrane （PPMM） through a ring opening polymerization of L-glutamate N-carboxyanhydride initiated by amino groups which were introduced by ammonia plasma and y-aminopropyl triethanoxysilane treatments. X-ray photoelectron spectroscopy （XPS）, attenuated total reflectance Fourier transform infrared spectroscopy （FT-IR/ATR）, scanning electron microscopy （SEM）, together with water contact angle measurements were used to characterize the modified membranes. XPS analyses and FT-IR/ATR spectra demonstrated that polypeptides are actually grafted onto the membrane surface. The wettability of the membrane surface increases at first and then decreases with the increase in grafting degrees of polypeptide. Platelet adhesion and murine macrophage attachment experiments reveal an enhanced hemocompatibility for the polypeptide modified PPMMs. All these results give evidence that polypeptide grafting can simultaneously improve the hemocompatibility as well as reserve the hydrophobicity for the membrane, which will provide a potential approach to improve the performance of polypropylene hollow fiber microporous membrane used in artificial oxygenator.

MICROPOROUS PVDF-HFP-BASED POLYMER MEMBRANES FORMED FROM SUPERCRITICAL CO_2 INDUCED PHASE SEPARATION

Microporous poly(vinylidene fluoride-co-hexafluoropropylene)(PVDF-HFP)membranes following supercritical CO_2 induced phase separation process were prepared using four solvents.The solid electrolytes of PVDF-HFP were formed by microporous PVDF-HFP membranes filled and swollen by a liquid electrolyte.The effect of the solvents on the morphology and structure,electrolyte absorptions and lithium ionic conductivity of the activated membranes were investigated.It was approved that all the membrane had the similar...

Effect of sol size on nanofiltration performance of a sol-gel derived microporous zirconia membrane

This paper reports the effect of sol size on nanofiltration performances of sol–gel derived microporous zirconia membranes. Microstructure, pure water flux, molecular weight cut-off(MWCO) and salt retention of zirconia membranes derived from zirconia sols with different sizes were characterized. Thermal evolution, phase composition, microstructure and chemical stability of unsupported zirconia membranes(powder) were determined by thermogravimetric and differential thermal analysis, X-ray diffraction, nitrogen adsorption–desorption and static solubility measurements. Results show that nanofiltration performance of zirconia membranes is highly dependent on sol size. The sol with an average size of 3.8 nm, which is smaller than the pore size of the γ-Al2O3support(pore size: 5–6 nm), forms a discontinuous zirconia separation layer because of excessive penetration of sol into the support. This zirconia membrane displays a MWCO value towards polyethylene glycol higher than 4000 Da. A smooth and defect-free zirconia membrane with a MWCO value of 1195 Da(pore size: 1.75 nm) and relative high retention rates towards Mg Cl2(76%) and Ca Cl2(64%) was successfully fabricated by dip-coating the sol with an appropriate size of 8.6 nm. Zirconia sol with an average size of 12 nm exhibits colloidal nature and forms a zirconia membrane with a MWCO value of 2332 Da(pore size: 2.47 nm). This promising microporous zirconia membrane presents sufficiently high chemical stability in a wide p H range of 1–12.

PREPARATION AND CHARACTERIZATION OF PVDF-HFP MICROPOROUS MEMBRANE BY TEMPLATE METHOD

Porous poly（vinylidene fluoride-co-hexafluoropropylene） （PVDF-HFP） membranes were successfully prepared using dibutyl phthalate （DBP）, polyvinylpyrrolidone （PVP-K30）, polyethylene glycol 200 （PEG200） as templates. SEM was used to examine the morphology of the PVDF-HFP porous membranes. It was found that these membranes have an asymmetric structure and the blends of PVDF-HFP/DBP formed nanoporous membranes, whereas the blends of PVDF- HFP/PVP-K30 formed ＂sponge-like＂ and microporous membranes. Moreover, the average pore size and porosity was about 0.3 μm and 48.7%, respectively. The crystallinity, thermal stability and mechanical strength of membranes were characterized by XRD, DSC, TGA and stress-strain tests. The results showed that the membranes are a crystals with excellent thermal stability. It was an effective way to regulate pore size and morphology of the PVDF-HFP membranes.

THEORETICAL EFFECTS OF MOLECULAR DIMENSION AND CONFIGURATION ON EFFECTIVE DIFFUSION COEFFICIENT OF MACROMOLECULES IN MICROPOROUS MEMBRANES

This paper presents a theoretical method for predicting the effective diffusion coefficient of macromolecules in the microporous membrfines in view of the effects of molecular dimension and configuration. On the basis of the hindered diffusion theory of spherical neutral macromolecules in a micropore of a long cylinder, the effects of molecular dimension and configuration are studied by defining two molecular dimensions:the mean projected radius to predict the concentration partition and the ' hydrodynamically equivalent sphere' radius to evaluate the hydrodynamic reverse drag force. The quantitative comparison shows that the effective diffusion coefficients for different macromolecules predicted by the present method are more consistent with the available published experimental data.

Gas separation using sol–gel derived microporous zirconia membranes with high hydrothermal stability

A microporous zirconia membrane with hydrogen permeance about 5 × 10-8mol·m-2·s-1·Pa-1, H2/CO2 permselectivity of ca. 14, and excellent hydrothermal stability under steam pressure of 100 k Pa was fabricated via polymeric sol–gel process. The effect of calcination temperature on single gas permeance of sol–gel derived zirconia membranes was investigated. Zirconia membranes calcined at 350 °C and 400 °C showed similar single gas permeance, with permselectivities of hydrogen towards other gases, such as oxygen, nitrogen, methane, and sulfur hexa fluoride, around Knudsen values. A much lower CO2permeance（3.7 × 10-9mol·m-2·s-1·Pa-1）was observed due to the interaction between CO2 molecules and pore wall of membrane. Higher calcination temperature, 500 °C, led to the formation of mesoporous structure and, hence, the membrane lost its molecular sieving property towards hydrogen and carbon dioxide. The stability of zirconia membrane in the presence of hot steam was also investigated. Exposed to 100 k Pa steam for 400 h, the membrane performance kept unchanged in comparison with freshly prepared one, with hydrogen and carbon dioxide permeances of 4.7 × 10-8and ~ 3 × 10-9mol·m-2·s-1·Pa-1, respectively. Both H2 and CO2permeances of the zirconia membrane decreased with exposure time to 100 k Pa steam. With a total exposure time of 1250 h, the membrane presented hydrogen permeance of 2.4 × 10-8mol·m-2·s-1·Pa-1and H2/CO2 permselectivity of 28, indicating that the membrane retains its microporous structure.

PREPARATION OF EVOH MICROPOROUS MEMBRANES via THERMALLY INDUCED PHASE SEPARATION USING BINARY SOLVENTS

Microporous ethylene-vinyl alcohol copolymer （EVOH） flat membranes and hollow-fiber membranes with 38 mol% ethylene content were prepared via thermally induced phase separation （TIPS） using the mixture of 1,4-butanediol and poly（ethylene glycol）（PEG400） as diluents. Effects of the ratio of 1,4-butanediol to PEG400 on the phase diagrams, phase separation mechanism and membrane morphology were studied by small angle light scattering （SALS） measurements, differential scanning calorimetry （DSC）, and scanning ele~：tron microscopy （SEM）. It was found that by varying the composition of the binary solvent, the phase diagrams and membrane morphology can be controlled successfully. Moreover, the phase diagrams showed that broader regions of Liquid-Liquid （L-L） phase separation were obtained, as well as closer distances between L-L phase separation lines and Solid-Liquid （S-L） phase separation lines, Interconnected structures observed both in the flat membrane and hollow fiber membrane consist with the above results.

In situ Synthesis of Oligonucleotides on Plasma Treated Polypropylene Microporous Membrane

Polypropylene microporous membranes were treated with plasma in a mixture of N2 and H2 (1:2 in volume). Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FT1R), X-ray photoelectron spectroscopy (XPS) and ultra-violet (UV) spectra demonstrated the success of grafting amino groups. The density of the polar amino groups on the membrane surface is about 0.59 μmol/cm2. The as-treated membranes were successively applied to the in situ synthesis of oligonucleotides and an average coupling yield was more than 98%. The surface feature of the treated membrane is suggested to be responsible for its advantage over a glass slide.

Preparation of YSZ Microporous Membranes on Porous α-Alumina with Metal chlorides as Precursor

ＰｒｅｐａｒａｔｉｏｎｏｆＹＳＺＭｉｃｒｏｐｏｒｏｕｓＭｅｍｂｒａｎｅｓｏｎＰｏｒｏｕｓα－ＡｌｕｍｉｎａｗｉｔｈＭｅｔａｌｃｈｌｏｒｉｄｅｓａｓＰｒｅｃｕｒｓｏｒＰＥＮＧＤｉｎｇ－ｋｕｎ，ＬＩＵＴａｏ，ＹＡＮＧＰｉｎｇ－ｈｕａ，ＸＩＡＣｈａｎｇ－ｒ...

Surface Functionalization of Microporous Polypropylene Membrane with Polyols for Removal of Boron Acid from Aqueous Solution

Affinity membranes are fabricated for boric acid removal by the surface functionalization of microporous polypropylene membrane(MPPM)with lactose-based polyols.The affinity is based on specific complexation between boric acid and saccharide polyols.A photoinduced grafting-chemical reaction sequence was used to prepare these affinity membranes.Poly(2-aminoethyl methacrylate hydrochloride)[poly(AEMA)]was grafted on the surfaces of MPPM by UV-induced graft polymerization.Grafting in the membrane pores was visualized by dying the cross-section of poly(AEMA)-grafted MPPM with fluorescein disodium and imaging with confocal laser scanning microscopy.It is concluded that lactose ligands can be covalently immobilized on the external surface and in the pores by the subsequent coupling of poly(AEMA)with lactobionic acid(LA).Physical and chemical properties of the affinity membranes were characterized by field emission scanning electron microscopy and Fourier Transform Infrared/Attenuated Total Refraction spectroscopy(FT-IR/ATR).3-Aminophenyl boric acid(3-APBA)was removed from aqueous solution by a single piece of lactose-functionalized MPPM in a dynamic filtration system.The results show that the 3-APBA removal reaches an optimal efficiency(39.5%)under the alkaline condition(pH9.1),which can be improved by increasing the immobilization density of LA.Regeneration of these affinity membranes can be easily realized through acid-base washing because the complexation of boric acid and saccharide polyol is reversible.

Conjugated microporous polymer membranes for chemical separations

Conjugated microporous polymers(CMPs) are a unique class of porous organic materials, which are constructed with π-conjugation structures leading to intrinsic micropores. The CMPs properties such as high surface area, intrinsic and rich micropores, interlocking and rigid structure, extensive π-conjugation and tunable band-gap, chemical and thermal stability, together with tailored functionalities, contribute to its abundant potential for application in fields such as photocatalysis, optoelectronics, energy storage, and chemical sensors. Recently, CMPs have gained importance in the field of membranes for chemical separation. In this review, we briefly discuss the historical development of CMPs, followed by a detailed description of the progress in state-of-the-art design, preparation, and application of CMPs in membranes. Additionally, we provide inference on the future prospects of CMPs as membranes.

Electroosmotic Water Vapor Transport across Novel, Smart, Functionalized Conducting Polymer Microporous Membranes in Active Mode at Very High Rates, with Concomitant Chemical Warfare (CW) Agent Blocking

Electroosmotic water vapor transport (WVT) across very thin, flexible, functionalized conducting polymer (CP) microporous (μP) membranes at a very high rate is reported. Both passive and active (6 VDC applied) WVT are reported, the latter for the first time ever. WVT occurs with concomitant, effective blocking of chemical warfare (CW) agents, again demonstrated for the first time ever. Initial active liquid||membrane||liquid interface studies demonstrated WVT rates of >1.7 × 10-5g .mm-2s-1, >3 × the highest prior reported values of 5 × 10-6g.mm-2s-1. Subsequent vapor||membrane|| vapor interface studies using industry-standard methods (including ASTM E96B Upright Cup (“WVT”), ASTM F2298 (“Dynamic Moisture Permeation Cell”) and ASTM F1868 (“Sweating Guard Hotplate”) were done at independent, external labs for independent corroboration. These yielded, e.g., WVT values of2564.4 g.m2.d-1 (passive) and3706.7 g.m2d-1 (active), to be compared with the highest (passive) value ever reported previously,984.8 g.m2.d-1 for a μP-Nylon membrane. More than 15 different membrane configurations, porosities and types were studied, including membranes with CP + organophosphate hydrolase (OPH), an enzyme reactive to CW agents. Efficient blocking of the actual CW agents GB, HD, VX is also reported, using the TOP-8-2-501standard. Membranes also passed all Industry-standard durability tests, e.g. ASTM D2261 (Tearing), ASTM D5034 (Breaking), ASTM D3886 (Abrasion), ASTM F392 (Gelbo Flex). Incorporation into smart soldiers’ garments was demonstrated;power consumption was -2. Mechanisms of enhanced WVT and CW agent blocking in the membranes are discussed.

Study of Effects of Low Doses UV Radiation on Microporous Polysulfone Membranes in Sterilization Process

Synthetic membranes have gained an important place in chemical technology and are used in a broad range of applications. UV irradiation is an age old process used for disinfection as well as for sterilization purposes. It is used for sterilizing equipment in which polysulfone (PSf) membranes are used. As a result, short time UV irradiation of polymer membranes has acquired importance in recent times. In the present study, microporous polysulfone membranes with0.108 mmthickness have been prepared using phase inversion method. Effect of UV irradiation on the membranes for short time intervals (0 - 60 minutes) has been investigated using UV-Vis and FTIR spectrophotometer, and SEM. The performance of the membranes has studied by filtration techniques. UV-Vis and IR spectra analysis and SEM images obtained suggest that chains scission and crosslink have occurred simultaneously in the irradiated membranes by UV radiation in a dose dependant manner. The pure water flux (PWF) values of irradiated membranes obtained from filtration studies were higher compared to that of the control membrane. These results show that a very short UV irradiation (2 minutes) affected the physicochemical characteristics of microporous polysulfone membrane which it increases with increase in time.