The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron mi...The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).展开更多
Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mas...Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.展开更多
The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of pr...The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of primary grains during controlled diffusion solidification(CDS) of Al-8Si alloy were investigated by using simulation and calculation.The results indicate that a lower mixing temperature is helpful for achieving more supercooled microscale Al-rich pockets in the mixture,and increasing the width and supercooling degree of supercooling zone in the Al-rich pockets,and thus,the nucleation rate.The nuclei grow up in nondendritic mode,resulting in spheroidal,at least,nondendritic grains.In a successful CDS,the superheat degrees of the two precursor melts should be limited within several degrees,and it is not necessary to extra stipulate the superheat degree of target alloy melt(Al-8Si) when the requirement about Gibbs energies of the three melts is matched.Subsequent observation on casting microstructures shows that the employed simulation and calculation processes are reasonable and the achieved results are reliable.展开更多
The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The r...The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope(SEM),and energy dispersive analysis of X-rays(EDAX) that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.展开更多
The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were inve...The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were investigated. The results indicated that the semi-solid slurry to satisfy rheocasting can be manufactured by low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power remarkably affected the morphology of primary α-Al and the size of primary α-Al, and there is no obvious effect of stirring time on primary α-Al. Compared with the samples made by low superheat pouring with no stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 were markedly improved by low superheat pouring and weak electromagnetic stirring. On the condition of weak electromagnetic stirring, the pouring temperature with low superheat can be suitably raised to reach the effectiveness obtained from the lower pouring temperature without stirring.展开更多
An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduc...An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduced into the system plays an important role in remarkably improving the distribution and content of AlP particles due to their similar crystal structure and lattice parameters. ZL109 alloys have shown fast modification response to the addition of 0.5% Al-15Si-3.5P master alloy at 720℃, with a mass of primary Si precipitating in size of about 15 μm. Also, coarse primary Si grains in AI-30Si alloy can be refined dramatically from 150 μm to 37 μm after the addition of 2.0% Al-15Si-3.5P master alloy at 850℃. The P recovery of the Al-15Si-3.5P master alloy is much higher than that of a Cu-8.5P master alloy due to the pre-formed AlP particles.展开更多
The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making proc...The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making process were investigated. The results indicate that the semi-solid slurry to satisfy rheocasting requirement can be made by a combination of low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power significantly affect the morphology and the size of primary α-Al, while there is no obvious effect of the stirring time on primary α-Al. Compared with the samples made by low superheat pouring without stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 Al alloy are markedly improved by a process of applying both low superheat pouring and weak electromagnetic stirring. Under the condition of weak electromagnetic stirring applied, the pouring temperature with low superheat can be equivalently to reach the effectiveness obtained from the even lower pouring temperature without stirring.展开更多
Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple componen...Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple components,the eutectics in the structure accounts for 50%-90%of the sum volume of such alloys.Therefore,understanding the modification mechanism and function rules of the AlSi eutectic solidification is the technical key in controlling the structures and properties of such casting alloys.The present paper chiefly reviews recent investigation developments and important conclusions along the lines of the functions of modification elements and their modification mechanism in the eutectic solidification of Al-Si alloys.展开更多
In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The resul...In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The results show that the number of Al-Si atomic clustersdecreases and that of Al-Al and Si-Si atomic clusters increases for the treated samples. The testswith ZL109 alloy indicate that a large amount of primary crystal Si appears in the solidifiedmicrostructure after treated by EP. It is found that EP can change the microstructure of liquidmetal by affecting the probability of electrons appearing in different atoms (Al and Si) in theliquid metal. The combining force of different atoms decreases relatively, and that of the sameatoms increases, which is the main reason of reducing the atomic cluster with different atoms(Al-Si) and increasing the atomic cluster with the same atoms (Al-Al, Si-Si). The increasing of theatomic cluster with the same atom cluster resulted in the increasing of Si activity and the higherpoint of eutectics in the phase diagram. It makes a lot of primary silicon appeared in ZL109 alloy.展开更多
An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of e...An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of eutectic Al-Si alloy have been investigated experimentally. It is found that the eutectic structure has been refined by solely imposing high magnetic field while it is coarsened under the electromagnetic vibration. Furthermore, polyhedral Si grains and non-dendritic α-Al appeared when the electromagnetic vibration strength was strong enough. The refining of eutectic structure is attributed to the decrease of diffusion coefficient caused by the strong magnetic field. The coarseness of eutectic structure may be attributed to the convection caused by electromagnetic vibration. Strong convection may break co-operative growth of eutectic phases to form polyhedral Si grains and non-dendritic α-Al.展开更多
The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresp...The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresponding mechanism were discussed.The results indicate that the application of high holding pressure(300 k Pa)enhances the feeding ability of the alloy,leading to an increase of the density.Meanwhile,the cooling rate of the alloy is increased by 100%.In addition,the tensile testing results show that the increase of holding pressure from 50 to 300 k Pa improves the tensile strength and elongation of the alloy by 6.2%and 81.3%,respectively.However,excessive holding pressure(400 k Pa)might lower the density and cooling rate of the alloy due to the feeding channels being blocked.展开更多
The purpose of this paper was to investigate the effects of solution treatment time and Sr-modification on the microstructure and property of the Al-Si piston alloy.It was found that as-cast microstructures of unmodif...The purpose of this paper was to investigate the effects of solution treatment time and Sr-modification on the microstructure and property of the Al-Si piston alloy.It was found that as-cast microstructures of unmodified and Sr-modified Al-Si alloys consisted of a coarse acicular plate of eutectic Si,Cu_3NiAl_6 and Mg_2Si phases in theα-Al matrix but different in size and morphology.Both size and inter-particle spacing of Si particles were significantly changed by increasing the solution treatment time.After a short solution treatment,the coarse acicular plate of the eutectic Si appears to be fragmented.Fully modified microstructure of Sr-modified alloy can reduce the solution treatment time compared to unmodified alloy.The maximum of a peak hardness value is found in the very short solution treatment of both Al-Si piston alloys.Compared to 10 h solution treatment,the solution treatment of 2-4 h is sufficient to achieve appropriate microstructures and hardness. The short solution treatment is very useful to increase the productivity and to reduce the manufacturing cost of the Al-Si piston alloys.展开更多
The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were ex...The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were examined using scanning electron microscopy(SEM) with energy-dispersive X-ray spectroscopy(EDX). A new method of electron probe microanalysis(EPMA) map scanning was used to analyze the Sr distribution, which gave quantitative results covering more Si particles. EPMA map scanning, together with SEM with EDX, was also used in analyzing the distribution of Fe phases. Results show that Fe-containing phase was related to the unmodified Si particles in samples with partial modification failure and the plate-like Si phases in samples without modification failure. Such a relationship was further confirmed by the microstructure observation.In conclusion, a partial failure of Sr-modification can be caused by both slow cooling rate and Fe-containing phases.展开更多
Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force ap...Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.展开更多
The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000...The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.展开更多
Electromagnetic filtration of primary Fe-rich phases (complex compound of AlFeSiMn) from Al-Si alloy melt containing 1.2 wt pct Fe have been studied by theoretical analysis and on a self-designed electromagnetic filtr...Electromagnetic filtration of primary Fe-rich phases (complex compound of AlFeSiMn) from Al-Si alloy melt containing 1.2 wt pct Fe have been studied by theoretical analysis and on a self-designed electromagnetic filtration equipment. The principle of the electromagnetic filtration is that the EMF (electromagnetic force) scarcely acts on the primary Fe-rich phases having low electric conductivity, which are then moved in the direction opposite to that of the EMF. Experimental results show that the primary Fe-rich phases are separated from Al-Si alloy melt and are collected in the filter while the melt is in horizontal flow. The removal efficiency of the primary iron-phases (77) calculated is less as the greatest flow velocity of the melt (UM) and the height of the filter (2h) are larger, while it becomes larger as EMF, operating distance of electromagnetic force (cr) and particle size (dv) become larger. It has been confirmed that the primary iron-phases larger than 20 jim can be removed efficiently by theoretical analysis and experiments. This new technique is high efficient and available for continuously flowing melts as compared with natural settling and filtration methods, which offer a possibility for recycling high quality aluminum alloys.展开更多
The iron-rich solids formed during solidification of Al-Si alloys which are known to be detrimental to the mechanical,physical and chemical properties of the alloys should be removed.On the other hand,Al-Si hypereutec...The iron-rich solids formed during solidification of Al-Si alloys which are known to be detrimental to the mechanical,physical and chemical properties of the alloys should be removed.On the other hand,Al-Si hypereutectic alloys are used to extract the pure primary silicon which is suitable for photovoltaic cells in the solvent refining process.One of the important issues in iron removal and in solvent refining is the effective separation of the crystallized solids from the Al-Si alloy melts.This paper describes the separation methods of the primary solids from Al-Si alloy melts such as sedimentation,draining,filtration,electromagnetic separation and centrifugal separation,focused on the iron removal and on the separation of silicon in the solvent refining process.展开更多
Large and segregated primary Si particles may drastically decrease the mechanical properties of Al-Si alloys. To solve this problem, a P-Cr complex modif ier was added into the alloy, and the effects of P-Cr complex m...Large and segregated primary Si particles may drastically decrease the mechanical properties of Al-Si alloys. To solve this problem, a P-Cr complex modif ier was added into the alloy, and the effects of P-Cr complex modification and solidification conditions on the microstructure of hypereutectic Al-Si alloys casting produced in wedge-shaped copper mould were studied. The thermal analysis technique was applied to calculate the cooling rate during solidification. The microstructures were observed by means of optical and scanning electron microscopies. Results showed that the primary Si segregates in the as-cast hypereutectic Al-Si alloys. The segregation of primary Si can be inhibited by adding a P+Cr complex modif ier and increasing the cooling rate during solidif ication. The ref inement of primary Si particles by P+Cr complex modif ication is due to the formation of CrS i2 and AlP particles which act as the heterogeneous nuclei for the primary Si phase. The segregation of Si was also inhibited through the adherence of heavier CrS i2 particles to the primary Si particles.展开更多
Effect of electric current on the cast microstructure of Al-Si alloy was investigated. It was found that themicrostructure of Al-Si alloy was refined as the electric current was applied during solidification. When DC ...Effect of electric current on the cast microstructure of Al-Si alloy was investigated. It was found that themicrostructure of Al-Si alloy was refined as the electric current was applied during solidification. When DC (Direct Current)was applied in solidification, the eutectic Si flakes are similar to those solidified without current, but its length was shortenedand its distribution was changed ,with most of the Si flakes arrange in the radial direction, because of the electromagneticforce that resulted from the DC. On the other hand, when AC (Alternating Current) was applied during the solidification ofAl-Si alloy, most of the minute hooks on the silicon flakes that were found under DC or without any applied current werebroken into small silicon particles. Through silicon concentration measurement by electron microprobe, it was found that thesilicon content in the α-AI matrix increased with the current application during solidification, and the effect is more obviouswhen AC was applied.展开更多
A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the all...A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.展开更多
基金financially supported by the National Key Research and Development Program of China(2022YFB3404201)the Major Science and Technology Project of Changchun City,Jilin Province(Grant No.20210301024GX)。
文摘The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).
文摘Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.
基金supported by the National Key Research and Development Program of China (Grant No.2018YFB2001800)。
文摘The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of primary grains during controlled diffusion solidification(CDS) of Al-8Si alloy were investigated by using simulation and calculation.The results indicate that a lower mixing temperature is helpful for achieving more supercooled microscale Al-rich pockets in the mixture,and increasing the width and supercooling degree of supercooling zone in the Al-rich pockets,and thus,the nucleation rate.The nuclei grow up in nondendritic mode,resulting in spheroidal,at least,nondendritic grains.In a successful CDS,the superheat degrees of the two precursor melts should be limited within several degrees,and it is not necessary to extra stipulate the superheat degree of target alloy melt(Al-8Si) when the requirement about Gibbs energies of the three melts is matched.Subsequent observation on casting microstructures shows that the employed simulation and calculation processes are reasonable and the achieved results are reliable.
文摘The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope(SEM),and energy dispersive analysis of X-rays(EDAX) that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.
基金The project was financially supported by the Hi-tech Research and Development Program of China (No. G2002AA336080) and the National Natural Science Foundation of China (No. 50374012)
文摘The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were investigated. The results indicated that the semi-solid slurry to satisfy rheocasting can be manufactured by low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power remarkably affected the morphology of primary α-Al and the size of primary α-Al, and there is no obvious effect of stirring time on primary α-Al. Compared with the samples made by low superheat pouring with no stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 were markedly improved by low superheat pouring and weak electromagnetic stirring. On the condition of weak electromagnetic stirring, the pouring temperature with low superheat can be suitably raised to reach the effectiveness obtained from the lower pouring temperature without stirring.
基金supported by the National Science Fund for Distinguished Young Scholars (No. 50625101)the Key Project of Science and Technology Research of the Ministry of Education of China (No. 106103)
文摘An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduced into the system plays an important role in remarkably improving the distribution and content of AlP particles due to their similar crystal structure and lattice parameters. ZL109 alloys have shown fast modification response to the addition of 0.5% Al-15Si-3.5P master alloy at 720℃, with a mass of primary Si precipitating in size of about 15 μm. Also, coarse primary Si grains in AI-30Si alloy can be refined dramatically from 150 μm to 37 μm after the addition of 2.0% Al-15Si-3.5P master alloy at 850℃. The P recovery of the Al-15Si-3.5P master alloy is much higher than that of a Cu-8.5P master alloy due to the pre-formed AlP particles.
基金The paper is supported by the Hi-tech Research and Develop-ment Program of China (Authorized No.: G2002AA336080), andthe National Natural Science Foundation of China (AuthorizedNo.: 50374012).
文摘The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making process were investigated. The results indicate that the semi-solid slurry to satisfy rheocasting requirement can be made by a combination of low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power significantly affect the morphology and the size of primary α-Al, while there is no obvious effect of the stirring time on primary α-Al. Compared with the samples made by low superheat pouring without stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 Al alloy are markedly improved by a process of applying both low superheat pouring and weak electromagnetic stirring. Under the condition of weak electromagnetic stirring applied, the pouring temperature with low superheat can be equivalently to reach the effectiveness obtained from the even lower pouring temperature without stirring.
文摘Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple components,the eutectics in the structure accounts for 50%-90%of the sum volume of such alloys.Therefore,understanding the modification mechanism and function rules of the AlSi eutectic solidification is the technical key in controlling the structures and properties of such casting alloys.The present paper chiefly reviews recent investigation developments and important conclusions along the lines of the functions of modification elements and their modification mechanism in the eutectic solidification of Al-Si alloys.
文摘In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The results show that the number of Al-Si atomic clustersdecreases and that of Al-Al and Si-Si atomic clusters increases for the treated samples. The testswith ZL109 alloy indicate that a large amount of primary crystal Si appears in the solidifiedmicrostructure after treated by EP. It is found that EP can change the microstructure of liquidmetal by affecting the probability of electrons appearing in different atoms (Al and Si) in theliquid metal. The combining force of different atoms decreases relatively, and that of the sameatoms increases, which is the main reason of reducing the atomic cluster with different atoms(Al-Si) and increasing the atomic cluster with the same atoms (Al-Al, Si-Si). The increasing of theatomic cluster with the same atom cluster resulted in the increasing of Si activity and the higherpoint of eutectics in the phase diagram. It makes a lot of primary silicon appeared in ZL109 alloy.
基金supported by the National Natural Science Foundation of China(No.59871026)
文摘An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of eutectic Al-Si alloy have been investigated experimentally. It is found that the eutectic structure has been refined by solely imposing high magnetic field while it is coarsened under the electromagnetic vibration. Furthermore, polyhedral Si grains and non-dendritic α-Al appeared when the electromagnetic vibration strength was strong enough. The refining of eutectic structure is attributed to the decrease of diffusion coefficient caused by the strong magnetic field. The coarseness of eutectic structure may be attributed to the convection caused by electromagnetic vibration. Strong convection may break co-operative growth of eutectic phases to form polyhedral Si grains and non-dendritic α-Al.
基金National Key Research Project of China(No.2016YFB0300901).
文摘The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresponding mechanism were discussed.The results indicate that the application of high holding pressure(300 k Pa)enhances the feeding ability of the alloy,leading to an increase of the density.Meanwhile,the cooling rate of the alloy is increased by 100%.In addition,the tensile testing results show that the increase of holding pressure from 50 to 300 k Pa improves the tensile strength and elongation of the alloy by 6.2%and 81.3%,respectively.However,excessive holding pressure(400 k Pa)might lower the density and cooling rate of the alloy due to the feeding channels being blocked.
文摘The purpose of this paper was to investigate the effects of solution treatment time and Sr-modification on the microstructure and property of the Al-Si piston alloy.It was found that as-cast microstructures of unmodified and Sr-modified Al-Si alloys consisted of a coarse acicular plate of eutectic Si,Cu_3NiAl_6 and Mg_2Si phases in theα-Al matrix but different in size and morphology.Both size and inter-particle spacing of Si particles were significantly changed by increasing the solution treatment time.After a short solution treatment,the coarse acicular plate of the eutectic Si appears to be fragmented.Fully modified microstructure of Sr-modified alloy can reduce the solution treatment time compared to unmodified alloy.The maximum of a peak hardness value is found in the very short solution treatment of both Al-Si piston alloys.Compared to 10 h solution treatment,the solution treatment of 2-4 h is sufficient to achieve appropriate microstructures and hardness. The short solution treatment is very useful to increase the productivity and to reduce the manufacturing cost of the Al-Si piston alloys.
基金supported by the International Science & Technology Cooperation Program of China(No.2015DFR50470)
文摘The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were examined using scanning electron microscopy(SEM) with energy-dispersive X-ray spectroscopy(EDX). A new method of electron probe microanalysis(EPMA) map scanning was used to analyze the Sr distribution, which gave quantitative results covering more Si particles. EPMA map scanning, together with SEM with EDX, was also used in analyzing the distribution of Fe phases. Results show that Fe-containing phase was related to the unmodified Si particles in samples with partial modification failure and the plate-like Si phases in samples without modification failure. Such a relationship was further confirmed by the microstructure observation.In conclusion, a partial failure of Sr-modification can be caused by both slow cooling rate and Fe-containing phases.
基金supported by the National Natural Science Foundation of China(Grant No.50001008)the China Postdoctoral Science Foundation.
文摘Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.
基金This project is financially supported by the National Natural Science Foundation of China (No. 50071028) the Natural Science Foundation of Shandong Province (No. L2000F01)
文摘The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.
基金This project was supported by the China PostdoctoralScience FOundation, the Research Fund for the DoctoralProgram of Higher Educ
文摘Electromagnetic filtration of primary Fe-rich phases (complex compound of AlFeSiMn) from Al-Si alloy melt containing 1.2 wt pct Fe have been studied by theoretical analysis and on a self-designed electromagnetic filtration equipment. The principle of the electromagnetic filtration is that the EMF (electromagnetic force) scarcely acts on the primary Fe-rich phases having low electric conductivity, which are then moved in the direction opposite to that of the EMF. Experimental results show that the primary Fe-rich phases are separated from Al-Si alloy melt and are collected in the filter while the melt is in horizontal flow. The removal efficiency of the primary iron-phases (77) calculated is less as the greatest flow velocity of the melt (UM) and the height of the filter (2h) are larger, while it becomes larger as EMF, operating distance of electromagnetic force (cr) and particle size (dv) become larger. It has been confirmed that the primary iron-phases larger than 20 jim can be removed efficiently by theoretical analysis and experiments. This new technique is high efficient and available for continuously flowing melts as compared with natural settling and filtration methods, which offer a possibility for recycling high quality aluminum alloys.
基金supported by the Basic Science Research Program through the National Research Foundation of Korea(NRF),the Ministry of Education,Science and Technology of Korea(No.2012R1A1A2007476)supported by the Korea University of Technology and Education
文摘The iron-rich solids formed during solidification of Al-Si alloys which are known to be detrimental to the mechanical,physical and chemical properties of the alloys should be removed.On the other hand,Al-Si hypereutectic alloys are used to extract the pure primary silicon which is suitable for photovoltaic cells in the solvent refining process.One of the important issues in iron removal and in solvent refining is the effective separation of the crystallized solids from the Al-Si alloy melts.This paper describes the separation methods of the primary solids from Al-Si alloy melts such as sedimentation,draining,filtration,electromagnetic separation and centrifugal separation,focused on the iron removal and on the separation of silicon in the solvent refining process.
基金financially supported by the National Basic Research Program of China(Grant No.:2012CB723307-03)the Fundamental Research Funds for the Central Universities(Grant No.:N130409003)the National Natural Science Foundation of China(Grant No.:51204046)of China
文摘Large and segregated primary Si particles may drastically decrease the mechanical properties of Al-Si alloys. To solve this problem, a P-Cr complex modif ier was added into the alloy, and the effects of P-Cr complex modification and solidification conditions on the microstructure of hypereutectic Al-Si alloys casting produced in wedge-shaped copper mould were studied. The thermal analysis technique was applied to calculate the cooling rate during solidification. The microstructures were observed by means of optical and scanning electron microscopies. Results showed that the primary Si segregates in the as-cast hypereutectic Al-Si alloys. The segregation of primary Si can be inhibited by adding a P+Cr complex modif ier and increasing the cooling rate during solidif ication. The ref inement of primary Si particles by P+Cr complex modif ication is due to the formation of CrS i2 and AlP particles which act as the heterogeneous nuclei for the primary Si phase. The segregation of Si was also inhibited through the adherence of heavier CrS i2 particles to the primary Si particles.
文摘Effect of electric current on the cast microstructure of Al-Si alloy was investigated. It was found that themicrostructure of Al-Si alloy was refined as the electric current was applied during solidification. When DC (Direct Current)was applied in solidification, the eutectic Si flakes are similar to those solidified without current, but its length was shortenedand its distribution was changed ,with most of the Si flakes arrange in the radial direction, because of the electromagneticforce that resulted from the DC. On the other hand, when AC (Alternating Current) was applied during the solidification ofAl-Si alloy, most of the minute hooks on the silicon flakes that were found under DC or without any applied current werebroken into small silicon particles. Through silicon concentration measurement by electron microprobe, it was found that thesilicon content in the α-AI matrix increased with the current application during solidification, and the effect is more obviouswhen AC was applied.
基金This work has been supported by the Flu,tda~ion Of harbin institute of Technology for Out standing YOungScientists (No. 1832).
文摘A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.