Eco-water conveyances applied to control desertification at the lower reaches of the Tarim River

The lower reaches of the Tarim River are one of the areas suffering from most severe sandy desertification in Xinjiang, Northwest China. Irrational utilization of water and land resources results in eco-environmental deterioration in the Tarim River. In May 2000, the local government carried out the water conveyances project in the Tarim River. The influence of water conveyance on desertification reversion is analyzed and discussed according to the monitoring data in the past three years. Based on monitored data of the nine observed sections, along the channel of conveyance, the intensity and scope of desertification reversion in the upper reaches are larger than those in the lower reaches. Dynamic changes of desertification reversion are more obvious from the channel of conveyance to its two sides. However, the range of influence and intensity of desertification reversion is limited at present. It is suggested that the way and range of water conveyances should be adjusted in the future.

3D Finite Element Simulation of Tunnel Boring Machine Construction Processes in Deep Water Conveyance Tunnel

Applying stiffness migration method,a 3D finite element mechanical model is established to simulate the excavation and advance processes.By using 3D nonlinear finite element method,the tunnel boring machine(TBM) excavation process is dynamically simulated to analyze the stress and strain field status of surrounding rock and segment.The maximum tensile stress of segment ring caused by tunnel construction mainly lies in arch bottom and presents zonal distribution.The stress increases slightly and limitedly in the course of excavation.The maximum and minimum displacements of segment,manifesting as zonal distribution,distribute in arch bottom and vault respectively.The displacements slightly increase with the advance of TBM and gradually tend to stability.

Fiber optic sensing and performance evaluation of a water conveyance tunnel with composite linings under super-high internal pressures

For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the deformation and failure characteristics of lining structures under internal water pressure are not well investigated in the literature,particularly for three-layer composite linings.This study presents an in situ experimental investigation on the response of two types of composite linings(i.e.separated and combined lining structures)subjected to internal pressures,in which a fiber optic nerve system(FONS)equipped with distributed strain and displacement sensing nerves was employed to monitor the performance of the two composite linings during testing.The experimental results clearly show that the damage of the tunnel lining under different internal pressures was mainly located in the self-compaction concrete layer.The separated lining structure responded more aggressively to the variations in internal pressures than the combined one.Moreover,two evaluation indices,i.e.radial displacement and effective stiffness coefficient,are proposed for describing the changes in the structural bearing performance.The effective stiffness coefficients of the two types of lining structures were reduced by 39.4%and 29.5%,respectively.Considering the convenience of field monitoring,it is suggested that the average strains at different layers can be used as characteristic parameters for estimating the health conditions of lining structures in service.The analysis results provide a practical reference for the design and health evaluation of water conveyance shield tunnels with composite linings.

Effect of Reference Conveyance Parameter Usage on Real Time Canal Performance: The Case of Fentale Irrigation Scheme in Ethiopia

In designing a canal system, a major problem is to decide what conveyance parameter to apply in the calculations. Since basic knowledge on this subject is lacking, it is usually taken from literatures. Most of the irrigation projects in Ethiopia are found to work below their expectation. One of the main reasons is the conveyance parameters variation from the expected (design) value which ultimately affects the envisioned conveyance efficiency. To evaluate this variation, Fentale irrigation scheme was used as case study. The conveyance efficiency used at the design stage was 80%, which was within Food and Agricultural Organization of the united nations recommendations;while the field survey value was 17%. Such huge variation was due to the fact that the assigned conveyance parameter values (roughness coefficient, hydraulic radius and bed slope) no longer represent the current situation of the scheme. Such variation has resulted in increase in the depth and top width of the water surface which further resulted in 13% and 3% increase in wetted perimeter and top width of the canal, respectively. Thus this study suggests that conveyance parameters shall be derived from history of existing irrigation schemes in a country, rather than adopting it from standard literatures. As such construction quality, maintenance activities and technological transfer activities in a country shall be seen in deciding the conveyance parameters. The study also suggests that the ever increasing water shortage in an irrigation project could be managed by proper maintenance of the entire irrigation system.

Land use/land cover change responses to ecological water conveyance in the lower reaches of Tarim River,China

The Tarim River is the longest inland river in China and is considered as an important river to protect the oasis economy and environment of the Tarim Basin.However,excessive exploitation and over-utilization of natural resources,particularly water resources,have triggered a series of ecological and environmental problems,such as the reduction in the volume of water in the main river,deterioration of water quality,drying up of downstream rivers,degradation of vegetation,and land desertification.In this study,the land use/land cover change(LUCC)responses to ecological water conveyance in the lower reaches of the Tarim River were investigated using ENVI(Environment for Visualizing Images)and GIS(Geographic Information System)data analysis software for the period of 1990-2018.Multi-temporal remote sensing images and ecological water conveyance data from 1990 to 2018 were used.The results indicate that LUCC covered an area of 2644.34 km^(2) during this period,accounting for 15.79%of the total study area.From 1990 to 2018,wetland,farmland,forestland,and artificial surfaces increased by 533.42 km^(2)(216.77%),446.68 km^(2)(123.66%),284.55 km^(2)(5.67%),and 57.51 km^(2)(217.96%),respectively,whereas areas covered by grassland and other land use/land cover types,such as Gobi,bare soil,and deserts,decreased by 103.34 km2(14.31%)and 1218.83 km2(11.75%),respectively.Vegetation area decreased first and then increased,with the order of 2010<2000<1990<2018.LUCC in the overflow and stagnant areas in the lower reaches of the Tarim River was mainly characterized by fragmentation,irregularity,and complexity.By analyzing the LUCC responses to 19 rounds of ecological water conveyance in the lower reaches of the Tarim River from 2000 to the end of 2018,we proposed guidelines for the rational development and utilization of water and soil resources and formulation of strategies for the sustainable development of the lower reaches of the Tarim River.This study provides scientific guidance for optimal scheduling of water resources in the region.

The Comparative Study of Chuangtse’s English Translations Under the Theory of Spirit Transmission and Meaning Conveyance

Cultural-loaded word is one of the most popular topics in translation studies.The theory of spirit transmission and meaning conveyance provides a new way for the translation of cultural-loaded word.Based on the A Happy Excursion,this paper makes a comparative analysis of the translation strategies of seven English versions.This study will reveal the similarities and differences between Chinese and foreign translators’translation strategies.

Predictive analysis of stress regime and possible squeezing deformation for super-long water conveyance tunnels in Pakistan

The prediction of the stress field of deep-buried tunnels is a fundamental problem for scientists and engineers. In this study, the authors put forward a systematic solution for this problem. Databases from the World Stress Map and the Crustal Stress of China, and previous research findings can offer prediction of stress orientations in an engineering area. At the same time, the Andersonian theory can be used to analyze the possible stress orientation of a region. With limited in-situ stress measurements, the Hock-Brown Criterion can be used to estimate the strength of rock mass in an area of interest by utilizing the geotechnical investigation data, and the modified Sheorey＇s model can subsequently be employed to predict the areas＇ stress profile, without stress data, by taking the existing in-situ stress measurements as input parameters. In this paper, a case study was used to demonstrate the application of this systematic solution. The planned Kohala hydropower plant is located on the western edge of Qinghai-Tibet Plateau. Three hydro-fracturing stress measurement campaigns indicated that the stress state of the area is SH - Sh 〉 Sv or SH 〉Sv 〉 Sh. The measured orientation of Sn is NEE （N70.3°-89°E）, and the regional orientation of SH from WSM is NE, which implies that the stress orientation of shallow crust may be affected by landforms. The modified Sheorey model was utilized to predict the stress profile along the water sewage tunnel for the plant. Prediction results show that the maximum and minimum horizontal principal stres- ses of the points with the greatest burial depth were up to 56.70 and 40.14 MPa, respectively, and the stresses of areas with a burial depth of greater than 500 m were higher. Based on the predicted stress data, large deformations of the rock mass surrounding water conveyance tunnels were analyzed. Results showed that the large deformations will occur when the burial depth exceeds 300 m. When the burial depth is beyond 800 m, serious squeezing deformations will occur in the surrounding rock masses, thus requiring more attention in the design and construction. Based on the application efficiency in this case study, this prediction method proposed in this paper functions accurately.

Parametric resonance of axially functionally graded pipes conveying pulsating fluid

Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.

Nonlinear dynamics of a circular curved cantilevered pipe conveying pulsating fluid based on the geometrically exact model

Due to the novel applications of flexible pipes conveying fluid in the field of soft robotics and biomedicine,the investigations on the mechanical responses of the pipes have attracted considerable attention.The fluid-structure interaction(FSI)between the pipe with a curved shape and the time-varying internal fluid flow brings a great challenge to the revelation of the dynamical behaviors of flexible pipes,especially when the pipe is highly flexible and usually undergoes large deformations.In this work,the geometrically exact model(GEM)for a curved cantilevered pipe conveying pulsating fluid is developed based on the extended Hamilton's principle.The stability of the curved pipe with three different subtended angles is examined with the consideration of steady fluid flow.Specific attention is concentrated on the large-deformation resonance of circular pipes conveying pulsating fluid,which is often encountered in practical engineering.By constructing bifurcation diagrams,oscillating shapes,phase portraits,time traces,and Poincarémaps,the dynamic responses of the curved pipe under various system parameters are revealed.The mean flow velocity of the pulsating fluid is chosen to be either subcritical or supercritical.The numerical results show that the curved pipe conveying pulsating fluid can exhibit rich dynamical behaviors,including periodic and quasi-periodic motions.It is also found that the preferred instability type of a cantilevered curved pipe conveying steady fluid is mainly in the flutter of the second mode.For a moderate value of the mass ratio,however,a third-mode flutter may occur,which is quite different from that of a straight pipe system.

Flow characteristics and Shannon entropy analysis of dense-phase pneumatic conveying under high pressure

Experiments of dense-phase pneumatic conveying of pulverized coal using nitrogen are carded out in an experimental test facility with the conveying pressure up to 4. 0 MPa and the gas-solid ratio up to 450 kg/m^3. The influences of different conveying differential pressures, coal moisture contents, gas volume flow rates and superficial velocities on the solid-gas ratios are investigated. Shannon entropy analysis of pressure fluctuation time series is developed to reveal the flow characteristics. Through investigation of the distribution of the Shannon entropy under different conditions, the flow stability and the evolutional tendency of the Shannon entropy in different regimes and regime transition processes are discovered, and the relationship between the Shannon entropy and the flow regimes is also established. The results indicate that the solid-gas ratio and the Shannon entropy rise with the increase in conveying differential pressure. The solid-gas ratio and the Shannon entropy reveal preferable regularity with gas volume flow rates. The Shannon entropy is different for different flow regimes, and can be used to identify the flow regimes. Both mass flow rate and the Shannon entropy decrease with the increase in moisture contents. The Shannon entropy analysis is a feasible approach for researching the characteristics of flow regimes, flow stability and flow regime transitions in dense-phase pneumatic conveying under high pressure.

Drilling Power Consumption and Soil Conveying Volume Performances of Lunar Sampling Auger

The sampling auger used in lunar sampling and return mission is to transmit power and convey soil, and its performance is the key factor of the whole mission. However, there is currently a lack of the optimization research on soil conveying volume and power consumption models in auger structure design. To provide the drilled object, the simulation lunar soil, whose physical and mechanical property is the same as the real soil, is made by reducing soil void ratio. The models are formulated to analyze the influence of auger structure parameters on power consumption and soil conveying volume. To obtain the optimized structure parameters of auger, the multi-objective optimization functions of the maximum soil conveying volume and minimum power consumption are developed. To verify the correctness of the models, the performances of different augers drilling simulation soil are tested. The test results demonstrate that the power consumption of optimized auger is the lowest both in theory and test, and the experimental results of soil conveying volume are in agreement with theoretical analysis. Consequently, a new method for designing a lunar sampling auger is proposed which includes the models of soil conveying volume and transportation power consumption, the optimization of structure parameters and the comparison tests. This method provides a reference for sampling auger designing of the Chinese Lunar Sample Mission.

Dynamic Characteristics of Marine Risers Conveying Fluid

The lateral vibration differential equation for a marine riser conveying fluid is derived by use of the small deflection theory, and the effect of internal flow velocity and top tension on the natural frequency of the riser is studied by use of FEM. At the same time, the preliminary relationship between the natural Frequency and riser span under different internal flow velocities is obtained, the effect of riser supports on the vibration frequency is computed. It is found that the natural frequency of the marine riser increases with the increase of top tension, however decreases with the increase of internal flow velocity. In addition, the Frequency decreases drastically with the increase of riser span.

DIFFERENTIAL QUADRATURE METHOD TO STABILITY ANALYSIS OF PIPES CONVEYING FLUID WITH SPRING SUPPORT

It is a new attempt to extend the differential quadrature method(DQM) to stability analysis of the straight and curved centerlinepipes conveying fluid. Emphasis is placed on the study of theinfluences of several parameters on the critical flow velocity.Compared to other methods, this method can more easily deal with thepipe with spring support at its boundaries and asks for much lesscomputing effort while giving ac- ceptable precision in the numericalresults.

Research of Algorithm for Judgement of Joint Elongation of Conveyer Belt

By analyzing the feature of the joint image of the conveyer belt with steel ropes, a quick judgement algorithm based on the gradient search for the joint ’s elongation is put forward. And at the same time its experiment result is also given in this paper.

Three-dimensional dynamics of supported pipes conveying fluid

This paper deals with the three-dimensional dynamics and postbuckling behavior of flexible supported pipes conveying fluid, considering flow velocities lower and higher than the critical value at which the buckling instability occurs. In the case of low flow velocity, the pipe is stable with a straight equilibrium position and the dynamics of the system can be examined using linear theory. When the flow velocity is beyond the critical value, any motions of the pipe could be around the postbuckling configuration(non-zero equilibrium position) rather than the straight equilibrium position, so nonlinear theory is required. The nonlinear equations of perturbed motions around the postbuckling configuration are derived and solved with the aid of Galerkin discretization. It is found, for a given flow velocity,that the first-mode frequency for in-plane motions is quite different from that for out-of-plane motions. However, the second-or third-mode frequencies for in-plane motions are approximately equal to their counterparts for out-of-plane motions, keeping almost constant values with increasing flow velocity. Moreover, the orientation angle of the postbuckling configuration plane for a buckled pipe can be significantly affected by initial conditions, displaying new features which have not been observed in the same pipe system factitiously supposed to deform in a single plane.

THE DYNAMIC BEHAVIORS OF VISCOELASTIC PIPE CONVEYING FLUID WITH THE KELVIN MODEL

Based on the differential constitutive relationship of linearviscoelastic material, a solid-liquid coupling vibration equation forviscoelastic pipe conveying fluid is derived by the D'Alembert'sprinciple. The critical flow velocities and natural frequencies ofthe cantilever pipe conveying fluid with the Kelvin model (flutterinstability) are calculated with the modified finite differencemethod in the form of the recurrence for- mula. The curves betweenthe complex frequencies of the first, second and third mode and flowvelocity of the pipe are plotted. On the basis of the numericalcalculation results, the dynamic behaviors and stability of the pipeare discussed. It should be pointed out that the delay time ofviscoelastic material with the Kelvin model has a remarkable effecton the dynamic characteristics and stability behaviors of thecantilevered pipe conveying fluid, which is a gyroscopicnon-conservative system.

DYNAMIC STABILITY OF A BEAM-MODEL VISCOELASTIC PIPE FOR CONVEYING PULSATIVE FLUID

The dynamic stability in transverse vibration of a viscoelastic pipe for conveying puisative fluid is investigated for the simply-supported case. The material property of the beammodel pipe is described by the Kelvin-type viscoelastic constitutive relation. The axial fluid speed is characterized as simple harmonic variation about a constant mean speed. The method of multiple scales is applied directly to the governing partial differential equation without discretization when the viscoelastic damping and the periodical excitation are considered small. The stability conditions are presented in the case of subharmonic and combination resonance. Numerical results show the effect of viscosity and mass ratio on instability regions.

HOPF BIFURCATION OF A NONLINEAR RESTRAINED CURVED PIPE CONVEYING FLUID BY DIFFERENTIAL QUADRATURE METHOD

This paper proposes a new method for investigating the Hopf bifurcation of a curved pipe conveying fluid with nonlinear spring support.The nonlinear equation of motion is derived by forces equilibrium on microelement of the system under consideration.The spatial coordinate of the system is discretized by the differential quadrature method and then the dynamic equation is solved by the Newton-Raphson method.The numerical solutions show that the inner fluid velocity of the Hopf bifurcation point of the curved pipe varies with different values of the parameter, nonlinear spring stiffness.Based on this,the cycle and divergent motions are both found to exist at specific fluid flow velocities with a given value of the nonlinear spring stiffness.The results are useful for further study of the nonlinear dynamic mechanism of the curved fluid conveying pipe.

FLOW-INDUCED INTERNAL RESONANCES AND MODE EXCHANGE IN HORIZONTAL CANTILEVERED PIPE CONVEYING FLUID (Ⅱ)

The Newtonian method is employed to obtain nonlinear mathematical model of motion of a horizontally cantilevered and inflexible pipe conveying fluid. The order magnitudes of relevant physical parameters are analyzed qualitatively to establish a foundation on the further study of the model. The method of multiple scales is used to obtain eigenfunctions of the linear free-vibration modes of the pipe. The boundary conditions yield the characteristic equations from which eigenvalues can be derived. It is found that flow velocity in the pipe may induced the 3：1, 2：1 and 1：1 internal resonances between the first and second modes such that the mechanism of flow-induced internal resonances in the pipe under consideration is explained theoretically. The 3：1 internal resonance first occurs in the system and is, thus, the most important since it corresponds to the minimum critical velocity.

Tracer Experimental Study of the Main Conveying Conduits of CCl_4 Pollutant in the Qiligou Water Supply Resource

The Ordovician karst groundwater in the Qiligou basin is an important water supply source. This groundwater has been seriously contaminated in recent years by Cfl4 from a pesticide plant located in the recharge area. The highest concentration of CCl4 in the groundwater is 3909.2μg/L. Large scale tracer experiments were carried out to study the conveying conduits for Cfl4 in the basin on May 1-6, 2005. Nontoxic, edible glucose was used as a tracer and it was detected by spectrophotometric techniques. Well area of the basin, was employed for injecting the tracer X-61, located near the pesticide plant in the southern recharge Ten wells widely located in the groundwater runoff area were used as observing and sampling wells. The results show that the migration of the pollutants is controlled by the water hydrodynamic field and by the development of karst conduits. The tracer did not enter the up-drainage wells, X-49 and X-47, near the injection point because the water levels at these wells are higher than at the injection point. The adjacent well X-62 is close to the injection site, but the tracer reached the well after eleven hours. Wells X-43, X-59, X-58, YY-1 and X-57, located in the syncline axis runoff area, are respectively 2.5, 3.5, 4.33, 4.38 and 5.44 kilometers from the in- jection site. The time for initial appearance of tracer was 4, 4, 2, 6 and 4 hours, respectively. The maximum runoff velocity （well X-58） is over two kilometers per hour, indicating that the karst conduits are well developed along the syncline basin axis. These conduits are the main conveying conduits for groundwater and Cfl4. Closer wells were not necessarily the first to receive tracer. This shows the inhomogeneity in karst development which causes complex runoff, and pollutant migration, patterns.