ELASTIC-PLASTIC CONSTITUTIVE RELATION OF PARTICLE REINFORCED COMPOSITES

In this paper, a systematic approach is proposed to obtain the macroscopic elastic-plastic constitutive relation of particle reinforced composites (PRC). The strain energy density of PRC is analyzed based on the cell model, and the analytical formula for the macro-constitutive relation of PRC is obtained. The strength effects of volume fraction of the particle and the strain hardening exponent of matrix material on the macro-constitutive relation are investigated, the relation curve of strain versus stress of PRC is calculated in detail. The present results are consistent with the results given in the existing references.

Intelligent method to develop constitutive relationship of Ti-6Al-2Zr-1Mo-1V alloy

The isothermal compression tests were carried out in the Thermecmastor-Z thermo-simulator at temperatures of 800, 850, 900, 950, 1000 and 1050 ℃ and the strain rates of 0.01, 0.1, 1 and 10 s-1. The influence of deformation temperature and strain rate on the flow stress of Ti-6Al-2Zr-IMo-IV alloy was studied. Based on the experimental data sets, the high temperature deformation behavior of Ti-6A1-2Zr-IMo-IV alloy was presented using the intelligent method of artificial neural network （ANN）. The results indicate that the predicted flow stress values by ANN model is quite consistent with the experimental results, which implies that the artificial neural network is an effective tool for studying the hot deformation behavior of the present alloy. In addition, the development of graphical user interface is implemented using Visual Basic programming language.

Effects of hot deformation parameters on flow stress and establishment of constitutive relationship system of BT20 titanium alloy

The hot compression experiments were performed to investigate the effects of hot deformation parameters on the flow stress of BT20(Ti-6Al-2Zr-1Mo-1V) titanium alloy. The results show that the flow stress decreases with the increment of deformation temperature and increases with the growth of strain rate. The peak stress moves toward the direction of strain reducing and the strain rate sensitivity increases with the rising deformation temperature. There is obvious deformation heating created during hot deformation under relatively higher strain rate and lower deformation temperature. The improved back propagation(BP) neural network with 3-20-16-1 architecture has been employed to establish the prediction model of flow stress using deformation degree, deformation temperature and strain rate as input variables. The predicted values obtained by BP network agree well with the measured values, the relative error is within 6.5% for the sample data and not bigger than 9% for the non-sample data, which indicates that the ANNs adopted can predict the flow stress of BT20 alloy effectively and can be used as constitutive relationship system applied to FEM simulation of plastic deformation.

Numerical Method for Modeling the Constitutive Relationship of Sand under Different Stress Paths

A numerical method was used in order to establish the constitutive relationship of sands under different stress paths, Firstly, based on the numerical method modeling the constitutive law of sands, the elastoplastic constitutive relationship of sand was established for three paths： the constant proportion of principle stress path, the conventional triaxial compression （CTC） path, and the p=constant （TC） path. The yield lines of plastic volumetric strain and plastic generalized shear strain were given. Through visualization, the three dimensional surface of the stress-strain relationship in the whole stress field （p, q） obtained under the three paths was plotted. Also, by comparing the stress-strain surfaces and yield locus of the three stress paths, the differences were found to be obvious, which demonstrates that the influence of the stress paths on constitutive law was not neglected. The numerical modeling method overcame the difficulty of finding an analytical expression for plastic potential. The results simulated the experimental data with an accuracy of 90% on average, so the constitutive model established in this paper provides an effective constitutive equation for this kind of engineering, reflecting the effect of practical stress paths that occur in sands.

CONSTITUTIVE RELATIONSHIP OF IN718 ALLOY FOR THERMOVISCOPLASTIC AND MICROSTRUCTURE EVOLUTION COUPLED ANALYSIS

The interaction between thermomechanical parameters and microstructure evolution is so intense that it must be considered during the finite element method （FEM） simulation of the hot plastic working process, for materials that are difficult to deform. Taking the microstructure evolution into account, a novel type of constitutive relationship has been put forward for the IN718 alloy. The microstructure evolution model was first established for the dominant microstructure evolution processes. Then the microstructure evolution models and the method to determine the local flow stress of the corresponding microstructure for current thermomechanical parameters and deformation history were presented. Once the local flow stresses of different structures and their volume contributions were defined, the apparent flow stress of the material could be determined as the weighted sum of the local flow stresses and volume contributions. To validate the proposed method, a thermoviscoplastics and microstructure evolution coupled analysis for a forging process of a critical IN718 disk forging was performed. The predicting results were in close agreement with the experimental data.

Stiffness and Shear Stress Distribution of Glulam Beams in Elastic-Plastic Stage:Theory,Experiments and Numerical Modelling

Traditional methods focus on the ultimate bending moment of glulam beams and the fracture failure of materials with defects,which usually depends on empirical parameters.There is no systematic theoretical method to predict the stiffness and shear distribution of glulam beams in elastic-plastic stage,and consequently,the failure of such glulam beams cannot be predicted effectively.To address these issues,an analytical method considering material nonlinearity was proposed for glulam beams,and the calculating equations of deflection and shear stress distribution for different failure modes were established.The proposed method was verified by experiments and numerical models under the corresponding conditions.Results showed that the theoretical calculations were in good agreement with experimental and numerical results,indicating that the equations proposed in this paper were reliable and accurate for such glulam beams with wood material in the elastic-plastic stage ignoring the influence of mechanic properties in radial and tangential directions of wood.Furthermore,the experimental results reported by the previous studies indicated that the method was applicable and could be used as a theoretical reference for predicting the failure of glulam beams.

Mechanical Properties and Constitutive Relationship of the High-Durable Parallel Strand Bamboo

Engineered bamboo has recently received lots of attention of civil engineers and professional researchers due to its better mechanical performance than that of softwood timber.Parallel strand bamboo is one important part of engineered bamboo for its excellent durable performance compared to the laminated veneer bamboo.The required curing temperature in hot-pressing process is usually higher than 120°C to reduce the content of nutri-tional ingredients and hemy cellulose,and to avoid the decay from the environment and insects.Nonetheless,the appearance of engineered bamboo gets darker with the increase of temperature during the hot-pressing process.In order to minimize the color deepening while maintaining the durability,a high-durable parallel strand bamboo(HPSB)with relative high hot-pressing temperature(140°C)was produced and tested.The present study inves-tigates the mechanical performance through tension,compression,shear and bending tests.The experimental behavior of the specimens was identified,including the failure mode and load-displacement relationship.It was demonstrated that the HPSB material had better mechanical performance parallel to grain,making it as a considerable structural material.The average elastic modulus parallel to grain was 14.1 GPa,and the tensile and compressive strengths were 120.7 MPa and 121.0 MPa,respectively.The tension perpendicular to grain should be avoided in the practical application due to the lower strength and elastic modulus.Two stress-strain relationships of tension and compression parallel to grain,including three-linear and quadratic function models,were proposed and compared with the experimental results.The three-linear model was then applied to the finite element model.The finite element analysis using ANSYS software was conducted to validate the feasibility of the constitutive relationship.The quadratic function model showed better agreement with the experimental results,but the three-linear relationship was also precise enough to analyze the bending tests of HPSB material,whereas being less accurate to describe the elastic-plastic compression behavior.

Constitutive relationship of ionic polymer-metal composite and static response character of its cantilever setup to voltage

As a new ionic polymer-metal composite(IPMC) for artificial muscle,the mechanical performance parameters and the relationship between the deformation and the electrical parameters of the IPMC were studied. With the digital speckle correlation method,the constitutive relationship of the IPMC was confirmed. With non-contact photography measurement,a cantilever setup was designed to confirm the relationship between the deformation of the IPMC film and the applied voltage. The relationship curve of tip displacement of the IPMC cantilever setup vs the voltage was achieved. The results indicate that the IPMC is isotropic,its elastic modulus is 232 MPa and Poisson ratio is 0.163. The curve achieved from the test of the tip displacement of the IPMC cantilever setup shows that the tip displacement reaches the maximum when the stimulated voltage is 5 V. And the tip displacement descends largely when the frequency of the applied voltage is between 30 mHz and 100 mHz.

ARTIFICIAL NEURAL NETWORK MODEL OF CONSTITUTIVE RELATIONSHIP FOR 2A70 ALUMINUM ALLOY

The hat deformation behavior of 2A70 aluminum alloy was investigated by means of isothermal compression tests performed on a Gleeble-1500 thermal simulator over a wide range of temperatures 360-480℃ with strain rates of 0.01-1s^-1 and the largest deformation of 60%, and the true stress of the material was obtained under the above-mentioned conditions. The experimental results shows that 2A70 aluminum alloy is a kind of aluminum alloy with the property of dynamic recovery; its flow stress declines with the increase of temperature, while its flow stress increases with the increase of strain rates. On the basis of experiments, the constitutive relationship of the 2A70 aluminum alloy was constructed using a BP artificial neural network. Comparison of the predicted values with the experimental data shows that the relative error of the trained model is less than ±3% for the sampled data while it is less than ±6% for the nonsampled data. It is evident that the model constructed by BP ANN can accurately predict the flow stress of the 2A70 alloy.

CONSTITUTIVE RELATIONSHIP OF SUPERALLOY IN718

Isothermal constant speed compression tests of superalloy IN718 were conducted using a computer-controlled MTS machine at temperatures from 960 to 1040℃, with initial strain rates from 0.001 s￣(1) to 1.0 s￣(1) and engineering strain from 0.1 to 0. 7.The variations of flow stress with deformation temperature, initial strain rate and engineering strain were analyzed in the paper. It was found that there was an obvious power-law relationship between flow stress and initial strain rate, which showed the behavior of strain rate hardening of superalloy IN718 at elevated temperatures.The relationship between flow stress and temperature could be described by an inverse trigonometric function.And the turning point on the curve may be related to the behavior of δ phase at 1000℃. Meanwhile, it was found that there was a complicated relationship between flow stress and strain,which was indicative of the comprehensive effect of work hardening and dynamic softening on flow stress during hot deformation. From the results of these tests, a constitutive equation of superalloy IN718 was developed.

bStudy on constitutive relationship of coal based on conventional triaxial compression test

Constitutive relationship of coal under triaxial compression must be determined during solving the theoretical calculation and numerical simulation about coal body failure. This paper carried out conventional triaxial compression test on No.3 coal of Baodian Colliery using MTS815.03 servo-controlled rock mechanical test system. The results indicate that the failure process of coal can be divided into 5 stages： densification stage, apparent linear elastic deformation stage, accelerated inelastic deformation stage, fracture and developing stage and plasticity flow stage. Combined with the test results, the constitutive relationship model of coal can be simplified as the four segments of straight line model of elastic-plastic hardening-plastic softening-residual perfectly plastic. Through fitting calculation of test data, the segmented constitutive equation of coal can be obtained.

Johnson-Cook dynamic constitutive relationship for TC16 titanium alloy

The true stress-strain curves of TC16 alloy with a wide range of strain rates were investigated under uniaxial quasi-static tension and uniaxial dynamic compression with the Instron 8032 test machine and the split Hopkinson bar respectively. The results indicate that the true stress increases with increasing strain rate,while decreases with increasing temperature. Under the 105 s-1 high strain rate and temperature higher than 673 K,the true stress would even be less than that under quasi-static condition. A new method incorporating TC16's stress-strain curve developing item was proposed to determine the coefficients in J-C model easily and to avoid the estimation of the adiabatic temperature rising. The Johnson-Cook dynamic constitutive relationship for TC16 was obtained for the first time. Good agreement was obtained between the model prediction and the experimental stress-strain curves for TC16 under both quasi-static and dynamic loadings.

Stochastic response of an axially moving viscoelastic beam with fractional order constitutive relation and random excitations

A convenient and universal residue calculus method is proposed to study the stochastic response behaviors of an axially moving viscoelastic beam with random noise excitations and fractional order constitutive relationship, where the random excitation can be decomposed as a nonstationary stochastic process, Mittag-Leffler internal noise, and external stationary noise excitation. Then, based on the Laplace transform approach, we derived the mean value function, variance function and covariance function through the Green＇s function technique and the residue calculus method, and obtained theoretical results. In some special case of fractional order derivative α , the Monte Carlo approach and error function results were applied to check the effectiveness of the analytical results, and good agreement was found. Finally in a general-purpose case, we also confirmed the analytical conclusion via the direct Monte Carlo simulation.

On the yield functions in Lagrangian stress space of elastic-plastic materials with internal constraints

In the present paper it is shown that the elastic range in the second Piola-Kirchhoff stress space can be chosen in a hyperplane which is through the origin of Lagrangian stress space and perpendicular to the normal of the constraint manifold at the plastic configuration, if the determinate stress response of the elastic-plastic material with simple internal constraints with some condition is correctly chosen, otherwise, it is in general in a hypersurface and the normal flow rule by Ⅱ yushin＇s postulate will have an indeterminate part. The choice of deterrninate stress response is probable because of its indeterminacy. Therefore the yield function should be a function of the second Piola-Kirchhoff stress lying in the hyperplane so that it is more simple and the back stress as the geometric center of the elastic range in general is inside the elastic range. Finally some examples are concerned.

Constitutive analysis of AZ31 magnesium alloy plate

The plastic deformation simulation of AZ31 magnesium alloy at different elevated temperatures （from 473 to 723 K） was performed on Gleeble-1500 thermal mechanical simulator at the strain rates of 0.01, 0.1, 1, 5 and 10 s-t and the maximum deformation degree of 80%. The relationship between the flow stress and deformation temperature as well as strain rate was analyzed. The materials parameters and the apparent activation energy were calculated. The constitutive relationship was established with a Zener-Hollomon （Z） parameter. The results show that the flow stress increases with the increase of strain rate at a constant temperature, but it decreases with the increase of deformation temperature at a constant strain rate. The apparent activation energy is estimated to be 129-153 kJ/mol, which is close to that for self-diffusion of magnesium. The established constitutive relationship can reflect the change of flow stress during hot deformation.

ELASTIC－PLASTIC CONSTITUTIVE MODELS BASED ON THE MULTIPLICATION PROCESSES OF DEFORMED GRAINS

According to the characteristics of micro-deformation of polycrystalline metal,the author divides grains intothree kinds and proposes a new conceplion of deformed grains.multiplication,from which some explicit elastic-Plastic constitutive equations can be deduced and some experimental results can be explained quantitativelv,It shows that the macro-yield,rate-correlativity work hardening and other phenomena are all closely related to the kinetic process of grains deformation.

STUDY ON THE GENERALIZED PRANDTL-REUSS CONSTITUTIVEEQUATION AND THE COROTATIONALRATES OF STRESS TENSOR

In this paper, the generalized Prandtl-Reuss (P-R) constitutive equations of elastic-plastic material in the presence of finite deformations through a new approach are studied. It analyzes the generalized P-R equation based on the material corotational rate and clarifies the puzzling problem of the simple shear stress oscillation mentioned in some literature. The paper proposes a modified relative rotational rate with which to constitute the objective rates of stress in the generalized P-R equation and concludes that the decomposition of total deformation rate into elastic and plastic parts is not necessary in developing the generalized P-R equations. Finally, the stresses of simple shear deformation are worked out.

Relationship Research between the Chinese Medicine Constitution and Sub-Health

With further development of the bio-psycho-social medical model, people began to re-examine the knowledge of disease and health. The concept of sub-health has also been proposed in western medicine. Because of the lack of a specific standard, it is difficult to make clinical diagnosis and treatments for sub-health. Chinese medicine constitution theory has been widely accepted in China, and has a set of executable standards. This paper puts forward a new research method that connects the sub-health in western medicine and Chinese medicine constitution theory together. The potential relationships and influences between Chinese medicine constitution theory and sub-health were analyzed and key content and research progress were discussed. The research method in this paper will provide new ideas for sub-health research.

Elastic-plastic analysis for pile-anchor supporting system of deep foundation pit

By using numerical analysis methods to simulate the deep excavation,a lot of analyses are established on the basis of two-dimensional plane strain,ignoring the fact that foundation pit possesses three dimensions. For soil constitutive relation,people always take linear and nonlinear model,without considering the plastic behavior of soil. Using plastic-elastic hardening model to simulate constitutive relation of soil characteristics,the authors carried out mechanical analysis for pit excavation and support. The results show that the analysis for the stress state of pile anchor system is an effective way which provides theoretical basis for calculation of soil displacement.

TEST AND STUDY ON THE CONSTITUTIV ERELATIONSHIP OF DESERT SAND UNDER MOVING VEHICLE

The mechanical properties of the sand of Takelamagan desert in Xinjiang under moving vehicle are studied by soil dynamic triaxial test apparatus. The nonlinear elastic constitutive model of the sand under moving vehicle is established first. These results lay the foundations for studying the interaction between vehicle running gear and the sand of Takelamagan desert in Xinjiang. and developing sand vehicle.