The stability and ductility of four buckling-restrained braces (BRBs) with brace joints were studied. The load-carrying element of BRB was fabricated with steel (Chinese Q235), and a layer of colloidal silica sheet (0...The stability and ductility of four buckling-restrained braces (BRBs) with brace joints were studied. The load-carrying element of BRB was fabricated with steel (Chinese Q235), and a layer of colloidal silica sheet (0.5 mm in thickness) or four layers of plastic film (0.2 mm in thickness) were used as unbonding materials to provide space to prevent the buckling of inner core in higher modes and facilitate its lateral expansion in case of compression. Based on the equation of BRBs with brace joints of different restrained stiffnesses, the buckling load is calculated considering the initial geometric imperfections and residual stress, and the theoretical values agree well with the experiment results. It is concluded that the buckling load and ductility of BRBs are influenced greatly by the restrained stiffness of brace joints. If the restrained stiffness is deficient, the unstrained segment of BRBs with less stiffness will buckle firstly. As a result, the ultimate load of BRBs decreases, and the maximum compression load is reduced to about 65% of the maximum tension load; the stiffness also degenerates, and there is a long decreasing stage on the back-bone curve in compression phase; the ductility decreases, i.e., the ultimate tension ductility and ultimate compression ductility are approximately 15 and 1.3 respectively, and the cumulative plastic ductility is only approximately 200. If the restrained stiffness of joint is large enough, the stability will be improved as follows: the yielding strength and ultimate strength of BRBs are nearly the same, and there is an obvious strain intensification in both tension and compression phases; the ductility of brace also increases obviously, i.e., the ultimate tension ductility and ultimate compression ductility are both approximately 14, and the cumulative plastic ductility reaches 782.展开更多
In present study, free vibration of cracked beams resting on two-parameter elastic foundation with elastically restrained ends is considered. Euler-Bemoulli beam hypothesis has been applied and translational and rotat...In present study, free vibration of cracked beams resting on two-parameter elastic foundation with elastically restrained ends is considered. Euler-Bemoulli beam hypothesis has been applied and translational and rotational elastic springs in each end considered as support. The crack is modeled as a mass-less rotational spring which divides beam into two segments. After governing the equations of motion, the differential transform method （DTM） has been served to determine dimensionless frequencies and normalized mode shapes. DTM is a semi-analytical approach based on Taylor expansion series that converts differential equations to recursive algebraic equations. The DTM results for the natural frequencies in special cases are in very good agreement with results reported by well-known references. Also, the DTM procedure yields rapid convergence beside high accuracy without any frequency missing. Comprehensive studies to analyze the effects of crack location, crack severity, parameters of elastic foundation and boundary conditions on dimensionless frequencies as well as effects of elastic boundary conditions on cracked beams mode shapes are carried out and some problems handled for first time in this paper. Since this paper deals with general problem, the derived formulation has capability for analyzing free vibration of cracked beam with every boundary condition.展开更多
An exact approach for free transverse vibrations of a Timoshenko beam with ends elastically restrained against rotation and translation and arbitrarily located internal restraints is presented. The calculus of variati...An exact approach for free transverse vibrations of a Timoshenko beam with ends elastically restrained against rotation and translation and arbitrarily located internal restraints is presented. The calculus of variations is used to obtain the equations of motion, the boundary conditions and the transitions conditions which correspond to the described mechanical system. The derived differential equations are solved individually for each segment of the beam with the corresponding boundary and transitions conditions. The derived mathematical formulation generates as particular cases, and several mathematical models are used to simulate the presence of cracks. Some cases available in the literature and the presence of some errors are discussed. New results are presented for different end conditions and restraint conditions in the intermediate elastic constraints with their corresponding modal shapes.展开更多
基金Supported by the "Eleventh Five-Year Plan" for Science and Technology Research of China (No. 2006BAJ01B02-02-03)Natural Science Foundation of Heilongjiang Province (No. ZJG0701)+1 种基金National Natural Science Foundation of China (No. 90715021, No. 50678057, No. 50978080)Natural Scientific Research Innovation Foundation of Harbin Institute of Technology (No. HIT. NSRIF. 2009)
文摘The stability and ductility of four buckling-restrained braces (BRBs) with brace joints were studied. The load-carrying element of BRB was fabricated with steel (Chinese Q235), and a layer of colloidal silica sheet (0.5 mm in thickness) or four layers of plastic film (0.2 mm in thickness) were used as unbonding materials to provide space to prevent the buckling of inner core in higher modes and facilitate its lateral expansion in case of compression. Based on the equation of BRBs with brace joints of different restrained stiffnesses, the buckling load is calculated considering the initial geometric imperfections and residual stress, and the theoretical values agree well with the experiment results. It is concluded that the buckling load and ductility of BRBs are influenced greatly by the restrained stiffness of brace joints. If the restrained stiffness is deficient, the unstrained segment of BRBs with less stiffness will buckle firstly. As a result, the ultimate load of BRBs decreases, and the maximum compression load is reduced to about 65% of the maximum tension load; the stiffness also degenerates, and there is a long decreasing stage on the back-bone curve in compression phase; the ductility decreases, i.e., the ultimate tension ductility and ultimate compression ductility are approximately 15 and 1.3 respectively, and the cumulative plastic ductility is only approximately 200. If the restrained stiffness of joint is large enough, the stability will be improved as follows: the yielding strength and ultimate strength of BRBs are nearly the same, and there is an obvious strain intensification in both tension and compression phases; the ductility of brace also increases obviously, i.e., the ultimate tension ductility and ultimate compression ductility are both approximately 14, and the cumulative plastic ductility reaches 782.
文摘In present study, free vibration of cracked beams resting on two-parameter elastic foundation with elastically restrained ends is considered. Euler-Bemoulli beam hypothesis has been applied and translational and rotational elastic springs in each end considered as support. The crack is modeled as a mass-less rotational spring which divides beam into two segments. After governing the equations of motion, the differential transform method （DTM） has been served to determine dimensionless frequencies and normalized mode shapes. DTM is a semi-analytical approach based on Taylor expansion series that converts differential equations to recursive algebraic equations. The DTM results for the natural frequencies in special cases are in very good agreement with results reported by well-known references. Also, the DTM procedure yields rapid convergence beside high accuracy without any frequency missing. Comprehensive studies to analyze the effects of crack location, crack severity, parameters of elastic foundation and boundary conditions on dimensionless frequencies as well as effects of elastic boundary conditions on cracked beams mode shapes are carried out and some problems handled for first time in this paper. Since this paper deals with general problem, the derived formulation has capability for analyzing free vibration of cracked beam with every boundary condition.
文摘An exact approach for free transverse vibrations of a Timoshenko beam with ends elastically restrained against rotation and translation and arbitrarily located internal restraints is presented. The calculus of variations is used to obtain the equations of motion, the boundary conditions and the transitions conditions which correspond to the described mechanical system. The derived differential equations are solved individually for each segment of the beam with the corresponding boundary and transitions conditions. The derived mathematical formulation generates as particular cases, and several mathematical models are used to simulate the presence of cracks. Some cases available in the literature and the presence of some errors are discussed. New results are presented for different end conditions and restraint conditions in the intermediate elastic constraints with their corresponding modal shapes.
