Due to complicated rock structure and environment, a prototype test for a tunnel-type anchorage is infeasible. Based on the rock mass parameters from tests, a three-dimensional （3D） elastoplastic analysis was perfor...Due to complicated rock structure and environment, a prototype test for a tunnel-type anchorage is infeasible. Based on the rock mass parameters from tests, a three-dimensional （3D） elastoplastic analysis was performed to simulate the influence of the construction procedure of Siduhe bridge with tunnel-type anchorage （TTA） in Hubei Province, China. The surrounding rock and concrete anchorage body were simulated by 8 nodes 3D brick elements. The geostatic state of the complex geometric structure was established with initial data. The in-situ concrete casting of the anchorage body and excavation of the rock mass were simulated by tetrahedral shell elements. The results show that the surrounding rock is in an elastic state under the designed cable force. The numerical overloading analysis indicates that the capacity of the surrounding anchorage is 7 times that of the designed cable force. The failure pattern shows that two anchorage bodies would be pulled out in the end. The maximum shear stress appears 10 m before the back anchorage face. The maximum range influenced by the TTA under ultimate loads is about 16 m.展开更多
Based upon nonlinear analysis theories for single-layer reticulated shells under fire conditions,more than 800 FEA models for four types of single-layer reticulated shells(K8,Geodesic,Schwedler,and Lamella) with diffe...Based upon nonlinear analysis theories for single-layer reticulated shells under fire conditions,more than 800 FEA models for four types of single-layer reticulated shells(K8,Geodesic,Schwedler,and Lamella) with different geometric parameters were set,and nonlinear finite element complete-process analysis under fire condition were conducted on the two typical cases,i.e.,global non-uniform temperature distribution and localized high temperature.By analyzing the calculation results for elasto-plastic stability bearing capacity,the practical calculation formulae for calculating elasto-plastic stability bearing capacity under fire condition were obtained.展开更多
More than 30 bending beams with rectangular cross-section and different thicknesses and heights were pre- pared from Q295 steel. The specimen dimensions were about 240 mm （length） × 60 mm （height） ×70 mm...More than 30 bending beams with rectangular cross-section and different thicknesses and heights were pre- pared from Q295 steel. The specimen dimensions were about 240 mm （length） × 60 mm （height） ×70 mm （thick ness）. Flaws were cut along its middle line with a wire cutter, with lengths ranging from 6 to 35 mm. Each specimen was tested with three-point bend loading, and a process curve was obtained between load and the displacement of the loading point, in order to analyze the fracture process when opening the crack. A deformation near the prefabricated crack was observed in the testing period, and the variation of the fracture characteristic parameters was analyzed for different sizes. For a comprehensive understanding of carbon steel fracture resistance behavior, its elasticity and plas- ticity were established by determining its Young＇s modulus and Poisson＇s ratio with an optical strain gauge. This gauge was also used for the loading process test. It was found that the fracture toughness varied with the dimensions, and the toughness of the elastic limit loading was almost constant. Using the relationship of crack resistance stress intensity factor and fracture criterion, the bearing capacity of the material structure could be estimated, which shows a good agreement with the experimental test data.展开更多
文摘Due to complicated rock structure and environment, a prototype test for a tunnel-type anchorage is infeasible. Based on the rock mass parameters from tests, a three-dimensional （3D） elastoplastic analysis was performed to simulate the influence of the construction procedure of Siduhe bridge with tunnel-type anchorage （TTA） in Hubei Province, China. The surrounding rock and concrete anchorage body were simulated by 8 nodes 3D brick elements. The geostatic state of the complex geometric structure was established with initial data. The in-situ concrete casting of the anchorage body and excavation of the rock mass were simulated by tetrahedral shell elements. The results show that the surrounding rock is in an elastic state under the designed cable force. The numerical overloading analysis indicates that the capacity of the surrounding anchorage is 7 times that of the designed cable force. The failure pattern shows that two anchorage bodies would be pulled out in the end. The maximum shear stress appears 10 m before the back anchorage face. The maximum range influenced by the TTA under ultimate loads is about 16 m.
基金supported by the National Natural Science Foundation of China (Grant No. 51208019)the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20091102120034)
文摘Based upon nonlinear analysis theories for single-layer reticulated shells under fire conditions,more than 800 FEA models for four types of single-layer reticulated shells(K8,Geodesic,Schwedler,and Lamella) with different geometric parameters were set,and nonlinear finite element complete-process analysis under fire condition were conducted on the two typical cases,i.e.,global non-uniform temperature distribution and localized high temperature.By analyzing the calculation results for elasto-plastic stability bearing capacity,the practical calculation formulae for calculating elasto-plastic stability bearing capacity under fire condition were obtained.
基金Sponsored by National Natural Science Foundation of China(51008166,11172311,10272068)
文摘More than 30 bending beams with rectangular cross-section and different thicknesses and heights were pre- pared from Q295 steel. The specimen dimensions were about 240 mm （length） × 60 mm （height） ×70 mm （thick ness）. Flaws were cut along its middle line with a wire cutter, with lengths ranging from 6 to 35 mm. Each specimen was tested with three-point bend loading, and a process curve was obtained between load and the displacement of the loading point, in order to analyze the fracture process when opening the crack. A deformation near the prefabricated crack was observed in the testing period, and the variation of the fracture characteristic parameters was analyzed for different sizes. For a comprehensive understanding of carbon steel fracture resistance behavior, its elasticity and plas- ticity were established by determining its Young＇s modulus and Poisson＇s ratio with an optical strain gauge. This gauge was also used for the loading process test. It was found that the fracture toughness varied with the dimensions, and the toughness of the elastic limit loading was almost constant. Using the relationship of crack resistance stress intensity factor and fracture criterion, the bearing capacity of the material structure could be estimated, which shows a good agreement with the experimental test data.
