Saturation Estimation with Complex Electrical Conductivity for Hydrate-Bearing Clayey Sediments:An Experimental Study

Clays have considerable influence on the electrical properties of hydrate-bearing sediments.It is desirable to understand the electrical properties of hydrate-bearing clayey sediments and to build hydrate saturation(S_(h))models for reservoir evaluation and monitoring.The electrical properties of tetrahydrofuran-hydrate-bearing sediments with montmorillonite are characterized by complex conductivity at frequencies from 0.01 Hz to 1 kHz.The effects of clay and Sh on the complex conductivity were analyzed.A decrease and increase in electrical conductance result from the clay-swelling-induced blockage and ion migration in the electrical double layer(EDL),respectively.The quadrature conductivity increases with the clay content up to 10%because of the increased surface site density of counterions in EDL.Both the in-phase conductivity and quadrature conductivity decrease consistently with increasing Sh from 0.50 to 0.90.Three sets of models for Sh evaluation were developed.The model based on the Simandoux equation outperforms Archie’s formula,with a root-mean-square error(E_(RMS))of 1.8%and 3.9%,respectively,highlighting the clay effects on the in-phase conductivity.The fre-quency effect correlations based on in-phase and quadrature conductivities exhibit inferior performance(E_(RMS)=11.6%and 13.2%,re-spectively)due to the challenge of choosing an appropriate pair of frequencies and intrinsic uncertainties from two measurements.The second-order Cole-Cole formula can be used to fit the complex-conductivity spectra.One pair of inverted Cole-Cole parameters,i.e.,characteristic time and chargeability,is employed to predict S_(h) with an E_(RMS) of 5.05%and 9.05%,respectively.

Fabrication of Graphene/Cu Composite by Chemical Vapor Deposition and Effects of Graphene Layers on Resultant Electrical Conductivity

Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the problem of how to control graphene to form desired Gr/Cu composite is not well solved. This paper aims at exploring the best parameters for preparing graphene with different layers on Cu foil by chemical vapor deposition(CVD)method and studying the effects of different layers graphene on Gr/Cu composite’s electrical conductivity. Graphene grown on single-sided and double-sided copper was prepared for Gr/Cu and Gr/Cu/Gr composites. The resultant electrical conductivity of Gr/Cu composites increased with decreasing graphene layers and increasing graphene volume fraction. The Gr/Cu/Gr composite with monolayer graphene owns volume fraction of less than 0.002%,producing the best electrical conductivity up to59.8 ×10^(6)S/m,equivalent to 104.5% IACS and 105.3% pure Cu foil.

Study of material agglomeration during nozzle injection of multiviscosity liquid into a fluidized bed reactor by the electric conductance method

Fluidized bed agglomeration is an important and challenging problem for thermal cracking in fluid cokers. A low coker temperature can be problematic because the bitumen is injected into the fluidized bed with a different viscosity, resulting in formation of agglomerates of varying sizes, which slows the cracking reactions. In the present study, the bed material agglomeration process during nozzle injection of multi- viscosity liquid was investigated in a fluidized bed operated at different mass ratios of the atomization gas to the liquid jets （GLR= 1%-3.5%） and gas velocities （3.9Umf and 5,9Umf） based on a conductance method using a water-sand system to simulate the hot bitumen-coke system at room temperature. During the tests of liquid-jet dispersion throughout the bed, different agglomeration stages are observed at both gas velocities. The critical amount oftert-butanol in the liquid jets that could lead to severe agglomeration of the bed materials （poor fluidization） at GLR = 1% is about 10 wt% at the low fluidizing gas velocity （3.9Umf） and 18wt% at the high gas velocity （5,9Umf）. This study provides a new approach for on-line monitoring of bed agglomeration during liquid injection to guarantee perfect contact between the atomized liquid and the bed particles.

Transport and Conductance in Fibonacci Graphene Superlattices with Electric and Magnetic Potentials

We investigate the electron transport and conductance properties in Fibonacci quasi-periodic graphene superlat- rices with electrostatic barriers and magnetic vector potentials. It is found that a new Dirac point appears in the band structure of graphene superlattice and the position of the Dirac point is exactly located at the energy corresponding to the zero-averaged w^ve number. The magnetic and eleetr/c potentials modify the energy band structure and transmission spectrum in entirely diverse ways. In addition, the angular-dependent transmission is blocked by the potential barriers at certain incident angles due to the appearance of the evanescent states. The effects of lattice constants and different potentials on angular-averaged conductance are also discussed.

Effect of Polyaniline/manganese Dioxide Composite on the Thermoelectric Effect of Cement-based Materials

To enhance the thermoelectric effect of cement-based materials,conductive polyaniline(PANI)modified MnO_(2)powder was synthesized and used as a thermoelectric component in the cement composites.The nanostructured PANI was deposited on the surface of the nanorod-shapedα-MnO_(2)particle and the weight ratio of PANI to MnO_(2)was 22.3:77.7 in the composite.The synthesized PANI/MnO_(2)composite was nanostructured according to the SEM image.The test results of the thermoelectric properties proved that the PANI/MnO_(2)composite was effective as the Seebeck coefficient and electrical conductivity values of the cement composites with PANI/MnO_(2)inside were 3-4 orders of magnitude higher than those of pure cement paste and the thermal conductivity values of these cement samples were similar.The obtained maximum figure of merit(ZT)value(2.75×10^(-3))was much larger than that of conductive materials reinforced cement-based composites.The thermoelectric effect of cement composites is mainly enhanced by the increased Seebeck coefficient and electrical conductivity in this work.

Thermal and Electrical Properties of Liquid Metal Gallium During Phase Transition

Liquid metal gallium has been widely used in numerous fields, from nuclear engineering, catalysts, and energy storage to electronics owing to its remarkable thermal and electrical properties along with low viscosity and nontoxicity. Compared with high-temperature liquid metals, room-temperature liquid metals, such as gallium(Ga), are emerging as promising alternatives for fabricating advanced energy storage devices, such as phase change materials, by harvesting the advantageous properties of their liquid state maintained without external energy input. However, the thermal and electrical properties of liquid metals at the phase transition are rather poorly studied, limiting their practical applications. In this study, we reported on the physical properties of the solid–liquid phase transition of Ga using a custom-designed, solid–liquid electrical and thermal measurement system. We observed that the electrical conductivity of Ga progressively decreases with an increase in temperature. However, the Seebeck coefficient of Ga increases from 0.2 to 2.1 μV/K, and thermal conductivity from 7.6 to 33 W/(K·m). These electrical and thermal properties of Ga at solid–liquid phase transition would be useful for practical applications.

Machine Learning Mapping of Soil Apparent Electrical Conductivity on a Research Farm in Mississippi

Open-source and free tools are readily available to the public to process data and assist producers in making management decisions related to agricultural landscapes. On-the-go soil sensors are being used as a proxy to develop digital soil maps because of the data they can collect and their ability to cover a large area quickly. Machine learning, a subcomponent of artificial intelligence, makes predictions from data. Intermixing open-source tools, on-the-go sensor technologies, and machine learning may improve Mississippi soil mapping and crop production. This study aimed to evaluate machine learning for mapping apparent soil electrical conductivity (ECa) collected with an on-the-go sensor system at two sites (i.e., MF2, MF9) on a research farm in Mississippi. Machine learning tools (support vector machine) incorporated in Smart-Map, an open-source application, were used to evaluate the sites and derive the apparent electrical conductivity maps. Autocorrelation of the shallow (ECas) and deep (ECad) readings was statistically significant at both locations (Moran’s I, p 0.001);however, the spatial correlation was greater at MF2. According to the leave-one-out cross-validation results, the best models were developed for ECas versus ECad. Spatial patterns were observed for the ECas and ECad readings in both fields. The patterns observed for the ECad readings were more distinct than the ECas measurements. The research results indicated that machine learning was valuable for deriving apparent electrical conductivity maps in two Mississippi fields. Location and depth played a role in the machine learner’s ability to develop maps.

Quantifying the Euphrates Electric Conductivity Depending on Parameters by Dimensional Analysis Method

The searching about methods to connect the variables with each other to reach equations including multi variables. The dimensional analysis is a method to facilitate the solution of difficult mathematic equations and experimental formulas;therefore methods of simplifying the difficult equations and obtaining a new equation with different variables is needed. In this study will use 2 methods (statically with dimensionally analysis) to obtain electric conductivity of water of Euphrates river by multi parameters that are time (t), temperature (Te), density, viscosity, discharge and water depth in upstream of Alhindya barrage which located in Babylon governorate, Iraq during winter 2019. The equations were obtained for EC with Te and t by data were collected from Alhindya barrage office with R2 = 0.999 and R2 = 0.995 by statically ways. Dimension analysis was utilized via 2 stages. In first stage was obtained on equation of EC with respect to Te, water density (ρ) and dynamic viscosity (μ) with constant time, depth of water and discharge and we obtain on R2 was 0.994 and R2 = 0.986. In second stage was obtained formula of EC with respect to Te, water density (ρ), dynamic viscosity (μ), with variable time, depth of water and discharge with we obtain on R2 = 0.945 and R2 = 0.94. The result of research indicates that applying the dimension analysis to connect more than one variable with each other to find best solutions and best methods to facilitate the solving the equations. From dimension analysis gave a clear visualization of the association of several variables to give a result that helps measure the electrical conductivity of water in the absence of a water test device.

Boosting overall saline water splitting by constructing a strain-engineered high-entropy electrocatalyst

High-entropy materials(HEMs),which are newly manufactured compounds that contain five or more metal cations,can be a platform with desired properties,including improved electrocatalytic performance owing to the inherent complexity.Here,a strain engineering methodology is proposed to design transition-metal-based HEM by Li manipulation(LiTM)with tunable lattice strain,thus tailoring the electronic structure and boosting electrocatalytic performance.As confirmed by the experiments and calculation results,tensile strain in the LiTM after Li manipulation can optimize the d-band center and increase the electrical conductivity.Accordingly,the asprepared LiTM-25 demonstrates optimized oxygen evolution reaction and hydrogen evolution reaction activity in alkaline saline water,requiring ultralow overpotentials of 265 and 42 mV at 10 mA cm−2,respectively.More strikingly,LiTM-25 retains 94.6%activity after 80 h of a durability test when assembled as an anion-exchange membrane water electrolyzer.Finally,in order to show the general efficacy of strain engineering,we incorporate Li into electrocatalysts with higher entropies as well.

A layered multifunctional framework based on polyacrylonitrile and MOF derivatives for stable lithium metal anode

Composite Li metal anodes based on three-dimensional(3D) porous frameworks have been considered as an effective material for achieving stable Li metal batteries with high energy density.However,uneven Li deposition behavior still occurs at the top of 3D frameworks owing to the local accumulation of Li ions.To promote uniform Li deposition without top dendrite growth,herein,a layered multifunctional framework based on oxidation-treated polyacrylonitrile(OPAN) and metal-organic framework(MOF) derivatives was proposed for rationally regulating the distribution of Li ions flux,nucleation sites,and electrical conductivity.Profiting from these merits,the OPAN/carbon nano fiber-MOF(CMOF) composite framework demonstrated a reversible Li plating/stripping behavior for 500 cycles with a stable Coulombic efficiency of around 99.0% at the current density of 2 mA/cm~2.Besides,such a Li composite anode exhibited a superior cycle lifespan of over 1300 h under a low polarized voltage of 18 mV in symmetrical cells.When the Li composite anode was paired with LiFePO_(4)(LFP) cathode,the obtained full cell exhibited a stable cycling over 500 cycles.Moreover,the COMSOL Multiphysics simulation was conducted to reveal the effects on homogeneous Li ions distribution derived from the above-mentioned OPAN/CMOF framework and electrical insulation/conduction design.These electrochemical and simulated results shed light on the difficulties of designing stable and safe Li metal anode via optimizing the 3D frameworks.

Effect of laser surface melting treatment on properties of electric copper busbar joints

Electrical conductance and temperature of electric copper busbar joints were measured under different torque moments. Experimental results show that laser surface melting can increase hardness and refine structure of the copper, and it does not deteriorate electric resistance. Meanwhile, the temperature of laser treated joints under electric current is slightly lower than that of original sample. Salt spray test shows that laser treated sample has better salt spray corrosion resistance than the original sample does. The electric resistance of both laser treated and original samples are increased with salt spray time. For the same salt spray time, the electric resistance of busbar joint is decreased with increasing torque moment.

Effect of rare earth addition on microstructural,mechanical and electrical characteristics of Cu-6% Fe microcomposites

Cu-6%Fe（mass fraction） microcomposites containing（0-0.30）% rare earth elements were prepared by cold drawing and intermediate heat treatments.Microstructure was observed, and mechanical properties and electrical conductivity were measured for alloys at various drawing strain levels.Adding rare earth elements could reduce the size of primary Fe and Cu dendrites of Cu-6%Fe.Ultimate tensile strength increased but electrical conductivity decreased with the increase of drawing strain.Rare earth additions in Cu-6%Fe slightly increased the strength at low strain and effectively improved the conductivity at high strain.Both strain hardening rate and conductivity loss of Cu-6%Fe containing rare earths were reduced at lower strain than Cu-6%Fe.

Influence of Metal Additives on the Electrical Conductivities of the Oxide Ceramics as an Electrode Material

The electrical conductivities are reported for various oxide ceramics and cermets at 1000°C.Adding metal can greatly enhance the electrical condnctivities of the oxide materials.The conductivity of the ceramic added with metal depends on:(1)the conductivity σ_o of the oxides;(2)the content of metal additives;(3)the dispersion of the metal phase among oxide phase.The conductivity of the metal added does not affect the con- ductivity of the metal-containing ceramic.Although the metal-containing ceramic has much higher conductivi- ty than oxide ceramic,the change rate of their conductivities with temperature is similar and is controlled by E_g of the oxide.

Effects of physical properties on electrical conductivity of compacted lateritic soil

Natural soils of various types have different electrical properties due to the composition,structure,water content,and temperature.In order to investigate the electrical properties of lateritic soil,electrical conductivity experiments have been conducted on a self-developed testing device.Test results show that the electrical conductivity of laterite increases with the increase of water content,degree of saturation and dry density.When the water content is below the optimum water content,the electrical conductivity of soils increases nonlinearly and the variation rate increases dramatically.However,when the water content,degree of saturation,or dry density increases to a certain value,the electrical conductivity tends to be a constant.In addition,soil electrical conductivity increases with the increase of temperature,and it is observed that the electrical conductivity decreases with the increase of the number of wetting–drying cycles.

Facile synthesis of high electrical conductive CoP via solid-state synthetic routes for supercapacitors

Co-P precursor was prepared by a mechanical alloying method and then is controlled to synthesis of CoP phase through an annealing method. The optimal conditions of ball milling and annealing temperature are investigated. The CoP exhibits higher electrical conductivity than graphite and cobalt oxide, showing excellent pseudocapacitive properties due its high electrical conductivity which can result in a fast electron transfer in high rate charge-discharge possess. The as-obtained CoP electrode achieves a high specific capacitance of 447.5 Fig at 1 Aug, and displays an excellent rate capability as well as good cycling stability. Besides, the asymmetric supercapacitor (ASC) based on the CoP as the positive electrode and activated carbon (AC) as the negative electrode was assembled and displayed a high rate capability (60% of the capacitance is retained when the current density increased from 1 Aug to 12 Aug), excellent cycling stability (96.7% of the initial capacitance is retained after 5000 cycles), and a superior specific energy of 19 Wh/kg at a power density of 350.8 W/kg. The results, suggest that the CoP electrode materials have a great potential for developing high-performance electrochemical energy storage devices. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

Effects of Annealing on Microstructure, Mechanical and Electrical Properties of AlCrCuFeMnTi High Entropy Alloy

The multi-component A1CrCuFeMnTi high entropy alloy was prepared using a vacuum arc melting process. Serial annealing processes were subsequently performed at 590 ℃, 750 ℃, 955 ℃ and 1 100 ℃ respectively with a holding time of 4 h at each temperature. The effects of annealing on microstructure, mechanical and electrical properties of as-cast alloy were investigated by using differential thermal analysis （DTA）, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results show that two C14 hexagonal structures remain unchanged after annealing the as-cast A1CrCuFeMnTi alloy specimens being heated to 1 100℃. Both annealed and as-cast microstructures show typical cast-dendrite morphology and similar elemental segregation. The hardness of alloys declines as the annealing temperature increases while the strength of as-cast alloy improves obviously by the annealing treatment. The electrical conductivities of annealed and as-cast alloys are influenced by the distribution of interdendrite re^ions which is rich in Cu element.

INTERACTION MODELS FOR EFFECTIVE THERMAL AND ELECTRIC CONDUCTIVITIES OF CARBON NANOTUBE COMPOSITES

The present article provides supplementary information of previous works of analytic models for predicting conductivity enhancements of carbon nanotube composites. The models, though fairly simple, are able to take account of the effects of conductivity anisotropy, nonstraightness, and aspect ratio of the CNT additives on the conductivity enhancement of the composite and to give predictions agreeing well with existing experimental data. The omitted detailed derivation of this model is demonstrated in the present article with a more systematical analysis, which may help with further development in this direction. Furthermore, the effects of various orientation distributions of CNTs are reported here for the first time. The information may be useful in design or fabrication technology of CNT composites for better or specified conductivities.

Electrical conductivity optimization of the Na3AlF6–Al2O3–Sm2O3 molten salts system for Al–Sm intermediate binary alloy production

Metal Sm has been widely used in making Al–Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al–Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant(CVCC) technique was used to measure the conductivity for the Na3AlF6–AlF3–LiF–MgF2–Al2O3–Sm2O3electrolysis medium in the temperature range from 905 to 1055°C. The temperature(t) and the addition of Al2O3(W(Al2O3)), Sm2O3(W(Sm2O3)), and a combination of Al2O3and Sm2O3into the basic fluoride system were examined with respect to their effects on the conductivity(κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature(t) and decreases with the addition of Al2O3or Sm2O3or both. We concluded that the optimal operation conditions for Al–Sm intermediate alloy production in the Na3AlF6–AlF3–LiF–MgF2–Al2O3–Sm2O3system are W(Al2O3) + W(Sm2O3) = 3wt%, W(Al2O3):W(Sm2O3) = 7:3, and a temperature of 965 to 995°C, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.

Experimental Study on the Electrical Conductivity of Orthopyroxene at High Temperature and High Pressure under Different Oxygen Fugacities

At presure 1.0-4.0 GPa and temperature 1073-1423 K and under oxygen partial pressure conditions, a YJ-3000t multi-anvil solid high-pressure apparatus and Sarltron-1260 Impedance/Gain-Phase analyzer were employed to conduct an in-situ measurement of the electrical conductivity of orthopyroxene. The buffering reagents consist of Ni＋NiO, Fe＋Fe3O4, Fe＋FeO and Mo＋MoO2 in order to control the environmental oxygen fugacity. Experimental results made clear that： （1） within the measuring frequency range from 10-1 to 106 Hz, the complex impedance （R） is of intensive dependence on the frequency; （2） The electrical conductivity （a） tends to increase along to the rise of temperature （T）, and Log a vs. 1/ T fit the Arrenhius linear relations; （3） Under the control of oxygen buffer Fe＋Fe3O4, with the rise of pressure, the activation enthalpy tends to increase whereas the electrical conductivity tends to decrease. The activation energy and activation volume of the main current carders of orthopyroxene have been obtained, which are （1.715±0.035） eV and （0.03±0.01） cm^3/mol, respectively; （4） Under given pressure and temperature, the electrical conductivity tends to increase with increasing oxygen fugacity, while under given pressure the activation enthalpy tends to decrease with increasing oxygen fugacity; and （5） The sample＇s small polarons mechanism has provided a reasonable explanations to the conduction behavior at high temperature and high pressure.

Influential Factors on Deicing Performance of Electrically Conductive Concrete Pavement

The deicing experiment of carbon fiber reinforced electrically conductive concrete （CFRC） slab was conducted in laboratory at first, then the deicing process of CFRC parement was analyzed by means of finite element method （FEM）. At last, based on the energy conservation law and the computing restdts of finite element method, the influential factors including the setting of electric heating layer, environmental temperature, the thickness of ice, material parameters, and deicing power on deicing performance and energy consumption were discussed.