Construction Safety Management of Mechanical and Electrical Installation Projects

Various industries today rely on the support of electromechanical equipment,expanding its scope of application and leading to an increase in electromechanical installation projects.However,due to the high level of expertise required and the potential risks involved,it is crucial to emphasize safety management during construction.This paper delves into the significance of construction safety management for electromechanical installation projects,identifies common problems encountered during construction,and proposes solutions.This analysis aims to provide relevant personnel with essential guidance and references for managing electromechanical installation projects safely.

Suitable contacting scheme for evaluating electrical properties of GaN-based p-type layers

A suitable contacting scheme for p-(Al)GaN facilitating quick feedback and accurate measurements is proposed in this study.22 nm p^(+)-GaN followed by 2 nm p-In_(0.2)Ga_(0.8)N was grown on p-type layers by metal-organic chemical vapor deposition.Samples were then cut into squares after annealing and contact electrodes using In balls were put at the corners of the squares.Good linearity between all the electrodes was confirmed inⅠ–Ⅴcurves during Hall measurements even with In metal.Serval samples taken from the same wafer showed small standard deviation of~4%for resistivity,Hall mobility and hole concentration.The influence of contact layer on the electrical characteristics of bulk p-type layers was then investigated by step etching technique using inductively coupled plasma etching and subsequent Hall-effect measurements.Identical values could be obtained consistently when a 28 nm non-conductive layer thickness at the surface was taken into account.Therefore,the procedures for evaluating the electrical properties of GaN-based p-type layers just using In balls proposed in this study are shown to be quick and useful as for the other conventionalⅢ–Ⅴmaterials.

Effects of vacancy and external electric field on the electronic properties of the MoSi_(2)N_(4)/graphene heterostructure

Recently,the newly synthesized septuple-atomic layer two-dimensional(2D)material MoSi_(2)N_(4)(MSN)has attracted attention worldwide.Our work delves into the effect of vacancies and external electric fields on the electronic properties of the MSN/graphene(Gr)heterostructure using first-principles calculation.We find that four types of defective structures,N-in,N-out,Si and Mo vacancy defects of monolayer MSN and MSN/Gr heterostructure are stable in air.Moreover,vacancy defects can effectively modulate the charge transfer at the interface of the MSN/Gr heterostructure as well as the work function of the pristine monolayer MSN and MSN/Gr heterostructure.Finally,the application of an external electric field enables the dynamic switching between n-type and p-type Schottky contacts.Our work may offer the possibility of exceeding the capabilities of conventional Schottky diodes based on MSN/Gr heterostructures.

Influence of alloy components on arc erosion morphology of Ag/MeO electrical contact materials

Arc erosion morphologies of Ag/MeO（10） electrical contact materials after 50000 operations under direct current of 19 V and 20 A and resistive load conditions were investigated using scanning electron microscope（SEM） and a 3D optical profiler（3DOP）. The results indicated that 3DOP could supply clearer and more detailed arc erosion morphology information. Arc erosion resistance of Ag/SnO_2（10） electrical contact material was the best and that of Ag/CuO（10） was the worst. Arc erosion morphology of Ag/MeO（10） electrical contact materials mainly included three different types. Arc erosion morphologies of Ag/ZnO（10） and Ag/SnO_2（10） electrical contact materials were mainly liquid splash and evaporation, and those of Ag/CuO（10） and Ag/CdO（10） were mainly material transfer from anode to cathode. Arc erosion morphology of Ag/SnO_2（6）In_2O_3（4） electrical contact materials included both liquid splash, evaporation and material transfer. In addition, the formation process and mechanism on arc erosion morphology of Ag/MeO（10） electrical contact materials were discussed.

Sliding electrical contact behavior of AuAgCu brush on Au plating

The sliding electrical contact behavior of AuAgCu brush on Au plating was investigated at various normal loads and sliding speeds.The contact voltage drop and electrical noise between the two brushes were measured and the resistance waveforms were recorded.The morphologies of the worn surfaces and wear debris of the brush and plating were observed.The results show that the contact voltage drop and electrical noise decrease with the addition of load whereas increase drastically with increasing sliding speed.With the electrical current in vacuum,the wear process of AuAgCu brush on Au plating involves adhesion,transfer of gold from the plating to the brush,rolling of wear debris between contact surfaces and arc-induced melt at the contact edge,and this gold-on-gold sliding electrical contact system is reliable within experiment period.

Arc erosion of AgSnO_2 electrical contacts at different stages of a break operation

Arc erosion studies are conducted on AgSnO2 contact materials at different stages in the break operation. A resistive load arrangement is used with up to 42 V DC at 24 A and a constant contact opening velocity. The arc current is terminated at different stages as the arc is drawn between the contacts enabling a study of the arcing phenomena up to that point. Surface profiling of the contacts is conducted to determine the extent of erosion at the different stages as the arc is drawn. Spectral analysis is also conducted on the arc and then related to the extent of erosion. The results show that particular features occur at different stages as the arc is drawn. As the arc is initially established, it goes through an ＂Arc Generation＂ regime where the arc roots are small and immobile on both the anode and the cathode. Material transfer occurs mainly from anode to cathode. The spectral analysis indicates that Sn and O species dominate the arc followed by the Ag species. As the arc is drawn further and enters the ＂Arc Degeneration＂ regime, the anode undergoes significantly larger erosion than the cathode. Also, both contacts indicate that multiple arc roots have formed, which are highly mobile in the later stages of the discharge. The spectral analysis indicates that Ag and N species are in high concentrations compared to other species. The mechanisms of erosion and deposition are discussed in relation to the species within the arc discharge. For the complete break operation, it is found that the anode undergoes major erosion, and it is thought that the gaseous ions species do not dominate the arc under these conditions of short arcs and voltage 〈42 V to cause cathode erosion.

Preparation and microstructure characterization of a nano-sized Ti^(4+)-doped AgSnO_2 electrical contact material

A Ti^4＋-doped nano-structured AgSnO2 material was prepared using sol-gel method and characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and scanning electron microscopy （SEM）. The results show that Ti^4＋ cations are successfully doped into the crystal lattice of SnO2, and thus significantly improve the electrical conductivity of the sample. Furthermore, the coating of Ag on Ti^4＋-doped SnO2 nano-sized particles enhances the surface wettability and enables the resulting AgSnO2 material to have better mechanical properties.

Effect of sintering temperature on the physical properties and electrical contact properties of doped AgSnO_2 contact materials

AgSnO_ 2 electrical contact materials doped with Bi_2O_3,La_2O_3,and TiO_2 were successfully fabricated by the powder metallurgy method under different initial sintering temperatures.The electrical conductivity,density,hardness,and contact resistance of the Ag Sn O_2/Bi_2O_3,AgSnO_2/La_2O_3,and AgSnO_2/Ti O_2 contact materials were measured and analyzed.The arc-eroded surface morphologies of the doped AgSnO_2 contact materials were investigated by scanning electron microscopy(SEM).The effects of the initial sintering temperature on the physical properties and electrical contact properties of the doped AgSnO_2 contact materials were discussed.The results indicate that the physical properties can be improved and the contact resistance of the AgSnO_2 contact materials can be substantially reduced when the materials are sintered under their optimal initial sintering temperatures.

Experiment and finite element method analysis mass erosion and transfer of Ag/La_2NiO_4-based electrical contacts during operation

A uniform transient temperature field model of electrical contacts operation was found by analyzing the process of closing arc constriction resistance Joule heat ~ breaking arc. Essential parameters of Ag/La2NiO4 electrical contact material for transient temperature field calculation were obtained through tests of electrical contact experimental instrument under 18 V DC in different cur- rents, other correlation experiments, and calculation anal- ysis. The finite element method was applied to solve the transient temperature field, and the features and distribution of the transient temperature field were obtained. The condition of material erosion and mass transfer can be forecasted by those calculation results. It is beneficial to research about the lifetime of Ag/La2NiO4 electrical material.

Evolution of the electrical contact of dynamic pantograph–catenary system

A good contact between the pantograph and catenary is critically important for the working reliability of electric trains, while the basic understanding on the electrical contact evolution during the pantograph--catenary system working is still ambiguous so far. In this paper, the evolution of electric contact was studied in respects of the contact resistance, temperature rise, and microstructure variation, based on a home-made pantograph-catenary simulation system. Pure carbon strips and copper alloy contact wires were used, and the experimental electrical current, sliding speed, and normal force were set as 80 A, 30 km/h, and 80 N, respectively. The contact resistance presented a fluctuation without obvious regularity, concentrating in the region of 25 and 50 mf~. Temperature rise of the contact point experienced a fast increase at the first several minutes and finally reached a steady state. The surface damage of carbon trips in microstructure analysis revealed a complicated interaction of the sliding friction, joule heating, and arc erosion.

Effects of silver powder particle size on the microstructure and properties of Ag-Yb_2O_3 electrical contact materials prepared by spark plasma sintering

mg-Yb203 electrical contact materials were fabricated by spark plasma sintefing （SPS）. The effects of silver powder particle size on the microstructure and properties of the samples were investigated. The surface morphologies of the sintered samples were examined by optical microscope （OM）, and the fracture morphologies were observed by scanning electron microscopy （SEM）. The physical and mechanical properties such as density, electrical resistivity, microhardness, and tensile strength were also tested. The results show that the silver powder particle size has evident effects on the sintered materials. Comparing with coarse silver powder （5 ktm）, homogeneous and fme microstmcture was obtained by fine silver powder （_〈0.5-1am）. At the same time, the electrical conductivity, microhardness, and tensile strength of the sin- tered samples with fine silver powder were higher than those of the samples with coarse silver powder. However, silver powder particle size has little influence on the relative densities, which of all samples （both by free and coarse silver powders） is more than 95%. The fracture characteristics are ductile.

Morphology and electrical contact properties of electrical connection materials in corrosive atmosphere

The impact mechanism of environmental fac tors, such as corrosive atmosphere, on connector materials was investigated, and the porosity of gold plating was tested. Series of inspections and analytical research meth ods were introduced in this article. The surface morphology of specimens after corrosion was observed by stereoscopic microscope and scanning electron microscope. Chemical constitution was examined by Xray energy spectrum. The contact resistances were measured by fourpoint method. The experiment results show that after exposure to certain environment, the corrosion products, such as Cu20, Cu（NO3）2.3H20, and NiO, are observed on the surface of the specimens without gold coatings, whereas the corrosion products appear to have circleshaped spots on goldplating surface after corrosion test, which indicate that the gold plating has good corrosion protection. The porosity is increased with the increase of corrosion time for every kind of specimens gold plated, and the corrosion degree of gold plating specimens is decreased with the increase of the thickness of gold coatings. The static contact resistances of circleshaped spots appear higher contact resistance than normal value, which can reach to 2,000 mr2 nearly. It is found that the high and unstable contact resistance of the pore and products is more likely to cause contact failure.

Testing results analysis of contact materials’electrical contact performance

Because of the different ways in which contact materials work, the basic requirements for silver metal oxide contact materials are different. They are anti-welded and anti-erosion when closed, anti-erosion when broken, and arc easily moved and have smaller contact resistance. In this paper, La2O3 is used as a stable oxide in contact material to replace CdO. A new type of Ag/SnO2-La2O3-Bi2O3 contact material is first obtained through using powder metallurgical method. Then electrical contact material parameter tester is used to test the electrical contact performance of the contact material. Through experiments, the arcing voltage and current curves, arcing energy curves, fusion power curves while broken and contact resistance while closed were obtained. Analysis of the results showed that the addition of La2O3 makes the contact material have the following advantages: smaller electrical wear, smaller arc energy, smaller contact resistance and arc is more easily extinguished.

Influence of the ambient air temperature on the electrical contact reliability of electromagnetic relay

The dynamic contact resistances of HH52P electromagnetic relays are measured under different ambient air tem- perature. Their diagnostic parameters are extracted and determined. It is found that the ambient air temperature obviously influ- ences some parameters. In order to research its influence on the electrical contact reliability of electromagnetic relay, the statistic analysis is applied to study the static contact resistance, the max of the dynamic contact resistance and the bounce time. It is found that the ambient air temperature regularly influences the three parameters. Thoroughly, the phenomenon is studied and analyzed in the point of material science so as to probe into the essential matter of it.

Technical research on optimization design of contacts of electrical connector

Pin and socket contacts are the key parts of electrical connector as aerospace electronic components. The contacts are also the direct carriers for signal transmitting of electronic equipments, passing the signal from the input end to the output end of electrical connector. The reliability of pin and socket contacts directly influences signal transmission. The goal of this study is to enhance the contact reliability of aerospace electrical connector. Computer simulation analysis was made on contacts performance data by utilizing the simulation system developed by PCL Language of MSC software. Furthermore, the results were experi- mentally validated so as to realize the objective of optimizing contacts design.

Influence of operation number on arc erosion behavior of Ag/Ni electrical contact materials

Arc erosion behavior of Ag/Ni materials with different operation numbers was investigated by OM,3DOP and SEM.The results indicated that the arc erosion of Ag/10Ni electrical contact material fabricated by sintering−extrusion technology was more and more serious with the operation numbers increasing from 1000 to 40000.With the same operation numbers,the arc erosion on anode was more serious than that on cathode.Besides,the pores preferred to emerge around the arc effect spot during the first 10000 operations.And the morphology of the molten silver on cathode and anode was different due to the action of gravity and arc erosion.Furthermore,the relationships among arc energy,arc time,welding force,electric resistivity,temperature and mass change on contacts were discussed,which indicated that the mass loss on cathode was mainly caused by the fracture of molten bridge.

Oxidized film on C_p/Cu-Cd electrical contact material

Constituents of the oxidized surface film on diamond particles reinforced Cu-Cd alloy matrix composite （Cp/Cu-Cd） were investigated by XPS. The results show that Cu2O is the main constituent when the oxidized film is thin; CuO appears only after the film is rather thick. The originally formed oxidized film on the Cp/Cu-Cd is about 10nm in thickness and is mainly composed of Cu2O and Cu. After oxidized at 120℃ over 30h, CuO is detected in the film.

Improving the Electrical Contact Property of Single-Walled Carbon Nanotube Arrays by Electrodeposition

A parallel method for the fabrication of metal contacts on single-walled carbon nanotube(SWNT)arrays was presented and the electrical contact property was evaluated by a SWNT-field effect transistor structure. Copper and gold contacts were fabricated on both semiconducting SWNTs and metallic SWNTs by using a maskless electrodeposition process. The SWNT array remained a p-type semiconductor after the electrodeposition. The contact resistance between SWNT array and microelectrodes was reduced more than 50% by the established copper contacts. The source-drain current of the carbon nanotube field-effect transistor(CNT-FET)structure can be further increased from 7.9 μA to 9.2 μA when the copper contacts were replaced by gold ones,which is probably due to the better contact property to SWNT of gold contacts with fine grain size.

Electrical Conductivity of Spark Plasma Sintered W-Cu and Mo-Cu Composites for Electrical Contact Applications

Tungsten copper and molybdenum copper composites, with weight percent copper in the range of 20% - 40%, have been produced using the spark plasma sintering (SPS) technique. Other specimens having similar compositions were also developed using the conventional techniques of Liquid Phase Sintering (LPS) and Infiltration. Electrical conductivity measurements showed that the specimens produced by the SPS process had substantially higher levels of electrical conductivity than those produced by the other methods. Relative density measurements showed that the SPS specimens achieved very high densification, with relative densities in the range of 99.1% - 100%. On the other hand, the specimens produced by LPS and infiltration had relative densities in the range of 88% - 92% and 96% - 98% respectively. The superior conductivity of the SPS specimens has been attributed to the virtually full densification achieved by the process. The effect of porosity on electrical conductivity has been discussed and three standard models were assessed using results from porous sintered skeletons of pure tungsten and pure molybdenum.

Influence of graphite content on sliding wear characteristics of CNTs-Ag-G electrical contact materials

CNTs-Ag-G electrical contact composite material was prepared by means of powder metallurgical method. The influence of the graphite content on sliding wear characteristics of electrical contact levels was examined. In experiments, CNTs content was retained as 1% (mass fraction), and graphite was added at content levels of 8%, 10%, 13%, 15% and 18%, respectively. The results indicate that with the increase of graphite content, the contact resistance of electrical contacts is enhanced to a certain level then remains constant. Friction coefficient decreases gradually with the increase of graphite content. Wear mass loss decreases to the minimum value then increases. With the small content of graphite, the adhesive wear is hindered, which leads to the decrease of wear mass loss, while excessive graphite brings much more worn debris, resulting in the increase of mass loss. It is concluded that wear mass loss reaches the minimum value when the graphite mass fraction is about 13%. Compared with conventional Ag-G contact material, the wear mass loss of CNTs-Ag-G composite is much less due to the obvious increase of hardness and electrical conductivity, decline of friction surface temperature and inhibition of adhesive wear between composites and slip rings.