Optimization of micro milling electrical discharge machining of Inconel 718 by Grey-Taguchi method

The optimization of micro milling electrical discharge machining（EDM） process parameters of Inconel 718 alloy to achieve multiple performance characteristics such as low electrode wear,high material removal rate and low working gap was investigated by the Grey-Taguchi method.The influences of peak current,pulse on-time,pulse off-time and spark gap on electrode wear（EW）,material removal rate（MRR） and working gap（WG） in the micro milling electrical discharge machining of Inconel 718 were analyzed.The experimental results show that the electrode wear decreases from 5.6×10-9 to 5.2×10-9 mm3/min,the material removal rate increases from 0.47×10-8 to 1.68×10-8 mm3/min,and the working gap decreases from 1.27 to 1.19 μm under optimal micro milling electrical discharge machining process parameters.Hence,it is clearly shown that multiple performance characteristics can be improved by using the Grey-Taguchi method.

Micro Electrical Discharge Machining(μEDM):Holes Drilling and Characterization of the Process Parameters

μEDM(micro-electrical discharge machining)is a process for machining conductive materials without mechanical contact;it is particularly suitable for machining hard materials.The principle consists in creating electrical discharges between a micro-tool and a workpiece,both of which are immersed in a dielectric.It is a complementary process to mechanical,laser,micro-machining techniques,and even to techniques derived from silicon microtechnology(RIE,DRIE,LIGA).However,the resolution ofμEDM is limited;it depends on several electrical and physical parameters.The goal of this paper is to characterize the holes obtained by drilling usingμEDM with different micro-tool diameters(Φ=250μm;Φ=80μm;Φ=40μm;Φ=20μm)for an experimental time of t=2 h.The results obtained let us conclude that a large diameter micro-tool(Φ=250μm)leads to removing a larger amount of material(43×10^(5)μm^(3))than small diameters:Φ=80μm;Φ=40μm;Φ=20μm where the removed volume is equal to 2.6×10^(5)μm^(3);105μm^(3);0.4×10^(5)μm^(3),respectively.The electrode-tool diameter influences the maximum depth of the holes;a diameter ofΦ=250μm generates a hole where the maximum depth is 170μm while small diameters:Φ=80μm;Φ=40μm;Φ=20μm provide holes with a depth of 82μm;51μm;50μm respectively.Through these experiments,we can also conclude that the lateral gap of the holes is almost constant.It is about 40μm whatever the diameter.

Parameter optimization model in electrical discharge machining process

Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper, artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining（EDM） of 6061 aluminium alloy in terms of material removal rate,kerf/slit width,surface finish and wear of electrode wire for different pulse on time and wire tension was studied.Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension.It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate.It seems that the higher wire tension facilitates steady machining process,which generates low wear in wire electrode and better surface finish.The surface roughness does not change notably with the variation of pulse on time.The appearance of the machined surfaces is very similar under all the machining conditions.The machined surface contains solidified molten material,splash of materials and blisters.The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input.The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side.The higher electrode wear introduces higher taper.

Surface Modification Process by Electrical Discharge Machining with Ti Powder Green Compact Electrode

This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.

Statistical Description of Debris Particle Size Distribution in Electrical Discharge Machining

Gap debris as discharge product is closely related to machining process in electrical discharge machining（EDM）. A lot of recent researches have focused on the relationship among debris size, surfaces texture, remove rate, and machining stability. The study on statistical distribution of debris size contributes to the research, but it is still superficial currently. In order to obtain the distribution law of the debris particle size, laser particle size analyzer（LPSA） combined with scanning electron microscope（SEM） is used to analyze the EDM debris size. Firstly, the heating dried method is applied to obtain the debris particles. Secondly, the measuring range of LPSA is determined as 0.5–100 μm by SEM observation, and the frequency distribution histogram and the cumulative frequency distribution scattergram of debris size are obtained by using LPSA. Thirdly, according to the distribution characteristic of the frequency distribution histogram, the statistical distribution functions of lognormal, exponentially modified Gaussian（EMG）, Gamma and Weibull are chosen to achieve curve fitting of the histogram. At last, the distribute law of the debris size is obtained by fitting results. Experiments with different discharge parameters are carried out on an EDM machine designed by the authors themselves, and the machining conditions are tool electrode of red-copper material, workpiece of ANSI 1045 material and working fluid of de-ionized water. The experimental results indicate that the debris sizes of all experiment sample truly obey the Weibull distribution. The obtained distribution law is significantly important for all the models established based on the debris particle size.

Experimental Research on Effects of Process Parameters on Servo Scanning 3D Micro Electrical Discharge Machining

Servo scanning 3D micro electrical discharge machining (3D SSMEDM) is a novel and effective method in fabricating complex 3D micro structures with high aspect ratio on conducting materials. In 3D SSMEDM process, the axial wear of tool electrode can be compensated automatically by servo-keeping discharge gap, instead of the traditional methods that depend on experiential models or intermittent compensation. However, the effects of process parameters on 3D SSMEDM have not been reported up until now. In this study, the emphasis is laid on the effects of pulse duration, peak current, machining polarity, track style, track overlap, and scanning velocity on the 3D SSMEDM performances of machining efficiency, processing status, and surface accuracy. A series of experiments were carried out by machining a micro-rectangle cavity (900 μm×600 μm) on doped silicon. The experimental results were obtained as follows. Peak current plays a main role in machining efficiency and surface accuracy. Pulse duration affects obviously the stability of discharge state. The material removal rate of cathode processing is about 3/5 of that of anode processing. Compared with direction-parallel path, contour-parallel path is better in counteracting the lateral wear of tool electrode end. Scanning velocity should be selected moderately to avoid electric arc and short. Track overlap should be slightly less than the radius of tool electrode. In addition, a typical 3D micro structure of eye shape was machined based on the optimized process parameters. These results are beneficial to improve machining stability, accuracy, and efficiency in 3D SSMEDM.

Micro Electrical Discharge Machining Deposition in Air for Fabrication of Micro Spiral Structures

Micro electrical discharge machining（EDM） deposition process is a new micro machining method for fabrication of metal micro structures. In this process, the high level of tool electrode wear is used to achieve the metal material deposition. Up to now, the studies of micro EDM deposition process focused mainly on the researches of deposition process, namely the effects of discharge parameters in deposition process on the deposition rate or deposition quality. The research of the formation of micro structures with different discharge energy density still lacks. With proper conditions and only by the z-axis feeding in vertical direction, a novel shape of micro spiral structure can be deposited, with 0.11 mm in wire diameter, 0.20 mm in outside diameter, and 3.78 mm in height. Then some new deposition strategies including angular deposition and against the gravity deposition were also successful. In order to find the forming mechanism of the spiral structures, the numerical simulation of the transient temperature distribution on the discharge point was conducted by using the finite-element method（FEM）. The results show that there are two major factors lead to the forming of the spiral structures. One is the different material removal form of tool electrode according with the discharge energy density, the other is the influenced degree of the movement of the removed material particles in the discharge gap. The more the energy density in single discharge is, the smaller the mass of the removed material particles is, and the easier the movements of which will be changed to form an order tendency. The fine texture characteristics of the deposited micro spiral structures were analyzed by the energy spectrum analysis and the metallographic analysis. It shows that the components of the deposited material are almost the same as those of the tool electrode. Moreover the deposited material has the brass metallic luster in the longitudinal profile and has compact bonding with the base material. This research is useful to understand the micro-process of micro EDM deposition better and helpful to increase the controllability of the new EDM method for fabrication of micro structures.

Machining performance on hybrid process of abrasive jet machining and electrical discharge machining

To develop a hybrid process of abrasive jet machining (AJM) and electrical discharge machining (EDM),the effects of the hybrid process parameters on machining performance were comprehensively investigated to confirm the benefits of this hybrid process.The appropriate abrasives delivered by high speed gas media were incorporated with an EDM in gas system to construct the hybrid process of AJM and EDM,and then the high speed abrasives could impinge on the machined surface to remove the recast layer caused by EDM process to increase the efficiency of material removal and reduce the surface roughness.In this study,the benefits of the hybrid process were determined as the machining performance of hybrid process was compared with that of the EDM in gas system.The main process parameters were varied to explore their effects on material removal rate,surface roughness and surface integrities.The experimental results show that the hybrid process of AJM and EDM can enhance the machining efficiency and improve the surface quality.Consequently,the developed hybrid process can fit the requirements of modern manufacturing applications.

Characteristic evaluation of Al_2O_3/CNTs hybrid materials for micro-electrical discharge machining

The characteristic evaluation of aluminum oxide （A1203）/carbon nanotubes （CNTs） hybrid composites for micro-electrical discharge machining （EDM） was described. Alumina matrix composites reinforced with CNTs were fabricated by a catalytic chemical vapor deposition method. A1203 composites with different CNT concentrations were synthesized. The electrical characteristic of A1203/CNTs composites was examined. These composites were machined by the EDM process according to the various EDM parameters, and the characteristics of machining were analyzed using field emission scanning electron microscope （FESEM）. The electrical conductivity has a increasing tendency as the CNTs content is increased and has a critical point at 5% A1203 （volume fraction）. In the machining accuracy, many tangles of CNT in A1203/CNTs composites cause violent spark. Thus, it causes the poor dimensional accuracy and circularity. The results show that conductivity of the materials and homogeneous distribution of CNTs in the matrix are important factors for micro-EDM of A1203/CNTs hybrid composites.

MICRO ELECTRICAL DISCHARGE MACHINING DEPOSITION IN AIR

A new deposition method is described using micro electrical discharge machining （EDM） to deposit tool electrode material on workpiece in air. The basic principles of micro electrical discharge deposition （EDD） are analyzed and the realized conditions are predicted. With an ordinary EDM shaping machine, brass as the electrode, high-speed steel as the workpiece, a lot of experiments are carried out on micro EDD systematically and thoroughly. The effects of major processing parameters, such as the discharge current, discharge duration, pulse interval and working medium, are obtained, As a result, a micro cylinder with 0.19 mm in diameter and 7.35 mm in height is deposited. By exchanging the polarities of the electrode and workpiece the micro cylinder can be removed selectively. So the reversible machining of deposition and removal is achieved, which breaks through the constraint of traditional EDM. Measurements show that the deposited material is compact and close to workpiece base, whose components depend on the tool electrode, material.

Micro electrical discharge machining of small hole in TC4 alloy

Aiming at machining deeply small holes in TC4 alloy,a series of experiments were carried out on a self-developed multi-axis micro electrical discharge machining(micro-EDM)machine tool.To improve machining efficiency and decrease relative wear of electrode in machining deeply small hole in TC4 alloy,many factors in micro-EDM,such as polarity,electrical parameters and supplying ways of working fluid were studied.Experimental results show that positive polarity machining is far superior to negative polarity machining;it is more optimal when open-circuit voltage,pulse width and pulse interval are 130 V,5μs and 15μs respectively on the self developed multi-axis micro-EDM machine tool;when flushing method is applied in micro-EDM,the machining efficiency is higher and relative wear of electrode is smaller.

Analysis of Wire Vibration in Wire Electric Discharge Machining Process

Wire electric discharge machining(WEDM)process is used for precision manufacturing.The accuracy of machining is function of various parameters like current,voltage,wire speed,gap between wire and work piece,wire oscillation,work material,wire material,etc.Once the process parameters are selected,it is important that the wire vibrations are less to obtain a good surface finish.Due to the importance of wire vibration in obtaining the surface finish,it is necessary to study the wire vibration.This paper discusses different models of wire vibration presented in the literature and simulates a closed form solution of wire vibration using MATLAB.The transverse vibration of wire is analysed as forced vibration of moving wire with excitation due to the sparks during machining.The resulting partial differential equation is solved by using finite difference method and vibration is also simulated in the finite element package‘ANSYS’.The wire behaviour is investigated under different operating conditions and results of the two methods are

Material properties and machining performance of hybrid Ti_2AlN bulk material for micro electrical discharge machining

Mn+1AXn(MAX) phases are a family of nanolaminated compounds that possess unique combination of typical ceramic properties and typical metallic properties.As a member of MAX phase,Ti2 AlN bulk materials are attractive for some high-temperature applications.The synthesis,characteristics and machining performance of hybrid Ti2 AlN bulk materials were focused on in this work.The bulk samples mainly consisting of Ti2 AlN MAX phase with density close to theoretic one were synthesized by a spark plasma sintering method.Scanning electron microscopy results indicate homogenous distribution of Ti2 AlN grains in the samples.Micro-hardness values are almost constant under different loads (6-6.5 GPa).A machining test was carried out to compare the effect of material properties on micro-electrical discharge machining (micro-EDM) performance for Ti2 AlN bulk samples and Ti6242 alloy.The machining performance of the Ti2 AlN sample is better than that of the Ti6242 alloy.The inherent mechanism was discussed by considering their electrical and thermal conductivity.

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.

Optimization of electrical discharge machining process parameters for Al6061/cenosphere composite using grey-based hybrid approach

Fly ash has congregated considerable attention as a potential reinforcement for aluminum matrix composites(AMCs)to enhance selective properties and reduce the cost of fabrication.However,poor machinability of such AMCs limits their application.The present study focuses on the preparation of cenosphere fly ash reinforced Al6061alloys by compo casting method.X-ray diffraction analysis of the prepared AMCs exposes the presence of cenosphere particles without any formation of other intermetallic compounds.In this study,electrical discharge machining(EDM)was engaged to examine the machinability of the prepared metal matrix composite(MMCs).The measured performance characteristics for the various combinations of input process parameters were considered to be MRR,EWR and SR.Face centered central composite design(CCD)of response surface method(RSM)was employed to design the number of experimental trials required and a hybrid approach of grey-based response surface methodology(GRSM)was imposed for predicting the optimal combination of processing parameter in EDM process.Generous improvement was observed in the performance characteristics obtained by employing both the optimal setting of machining parameters.The optical3D surface profile graphs of the ED machined surface also revealed the improvement in surface quality and texture employing the optimal processing conditions proposed by hybrid GRSM approach.

Comparative study on discharge conditions in micro-hole electrical discharge machining of tungsten carbide (WC-Co) material

WC-Co is used widely in die and mold industries due to its unique combination of hardness, strength and wear-resistance. For machining difficult-to-cut materials, such as tungsten carbide, micro-electrical discharge machining(EDM) is one of the most effective methods for making holes because the hardness is not a dominant parameter in EDM. This paper describes the characteristics of the discharge conditions for micro-hole EDM of tungsten carbide with a WC grain size of 0.5 μm and Co content of 12%. The EDM process was conducted by varying the condenser and resistance values. A R-C discharge EDM device using arc erosion for micro-hole machining was suggested. Furthermore, the characteristics of the developed micro-EDM were analyzed in terms of the electro-optical observation using an oscilloscope and field emission scanning electron microscope.

Three-dimensional machining of insulating ceramics materials with electrical discharge machining

The insulating ceramics were processed with sinking and wire cut electrical discharge machining(EDM). The new technology was named as the assisting electrode method. In the machining, the electrical conductive material was adhered on the surface of insulating workpiece as the starting point of electrical discharge. As the processing operated in oil, the electrical conductive product composed of decomposition carbon element from working oil adhered on the workpiece during discharge. The discharges generated continuously with the formation of the electrical conductive layer. So, the insulating ceramics turn to the machinable material by EDM. We introduced the mechanism and the application of the machining of insulating ceramics such as Si3N4 and ZrO2.

Scale Effects and a Method for Similarity Evaluation in Micro Electrical Discharge Machining

Electrical discharge machining（EDM） is a promising non-traditional micro machining technology that offers a vast array of applications in the manufacturing industry. However, scale effects occur when machining at the micro-scale, which can make it difficult to predict and optimize the machining performances of micro EDM. A new concept of ＂scale effects＂ in micro EDM is proposed, the scale effects can reveal the difference in machining performances between micro EDM and conventional macro EDM. Similarity theory is presented to evaluate the scale effects in micro EDM. Single factor experiments are conducted and the experimental results are analyzed by discussing the similarity difference and similarity precision. The results show that the output results of scale effects in micro EDM do not change linearly with discharge parameters. The values of similarity precision of machining time significantly increase when scaling-down the capacitance or open-circuit voltage. It is indicated that the lower the scale of the discharge parameter, the greater the deviation of non-geometrical similarity degree over geometrical similarity degree, which means that the micro EDM system with lower discharge energy experiences more scale effects. The largest similarity difference is 5.34 while the largest similarity precision can be as high as 114.03. It is suggested that the similarity precision is more effective in reflecting the scale effects and their fluctuation than similarity difference. Consequently, similarity theory is suitable for evaluating the scale effects in micro EDM. This proposed research offers engineering values for optimizing the machining parameters and improving the machining performances of micro EDM.

Integrated CAD/CAPP/CAM system for electric discharge machining

An integrated CAD/CAPP/CAM system modeling for Electric Discharge Machining (EDM) is constructed on the basis of an integrated engineering database. EDM feature objects are developed using the object oriented database provided by AutoCAD R14, and EDM feature modeling is realized in AutoCAD environments.