An Analytical Model for the Surface Electrical Field Distribution and Optimization of Bulk-Silicon Double RESURF Devices

A new 2D analytical model for the surface electrical field distribution and optimization of bulk-silicon double RESURF devices is presented. Based on the solution to the 2D Poisson＇s equation, the model gives the influence on the surface electrical field of the drain bias and structure parameters such as the doping concentration,the depth and the position of the p-top region, the thickness and the doping concentration of the drift region, and the substrate doping concentration. The dependence of breakdown voltage on the length and doping concentration of the drift region is also calculated. Further more,an effective way to gain the optimum high-voltage is also proposed. All analytical results are verified by simulation results obtained by MEDICI and previous experimental data,showing the validity of the model presented here.

A Novel Analytical Model for Surface Electrical Field Distribution and Optimization of TFSOI RESURF Devices

A novel analytical model for the thin film silicon on insulator (TFSOI) reduced surface field (RESURF) devices has been proposed.Based on the 2-D Poisson equation solution,the analytical expressions for the surface potential and field distributions are derived.From this analysis,the optimum design condition for the maximum breakdown voltage is obtained.The dependence of the maximum breakdown voltage on the drift region length is examined and the relationship between the critical doping concentration and the front- and back- interface oxide layer thickness is discussed.The numerical simulation performed by the advanced semiconductor simulation tool,DESSIS-ISE,has been shown to support the analytical results.

Two-dimensional investigation of characteristic parameters and their gradients for the self-generated electric and magnetic fields of laser-induced zirconium plasma

Two-dimensional diagnosis of laser-induced zirconium(Zr)plasma has been experimentally performed using the time-of-flight method by employing Faraday cups in addition to electric and magnetic probes.The characteristic parameters of laser-induced Zr plasma have been evaluated as a function of different laser irradiances ranging from 4.5 to 11.7 GW cm-2 at different axial positions of 1–4 cm with a fixed radial distance of 2 cm.A well-supporting correlation between the plume parameters and the laser-plasma-produced spontaneous electric and magnetic(E and B)fields was established.The measurements of the characteristic parameters and spontaneously induced fields were observed to have an increasing trend with the increasing laser irradiance.However,when increasing the spatial distance in both the axial and radial directions,the plasma parameters(electron/ion number density,temperature and kinetic energy)did not show either continuously increasing or decreasing trends due to various kinetic and dynamic processes during the spatial evolution of the plume.However,the E and B fields were observed to be always diffusing away from the target.The radial component of electron number densities remained higher than the axial number density component,whereas the axial ion number density at all laser irradiances and axial distances remained higher than the radial ion number density.The higher axial self-generated electric field(SGEF)values than radial SGEF values are correlated with the effective charge-separation mechanism of electrons and ions.The generation of a self-generated magnetic field is observed dominantly in the radial direction at increasing laser irradiance as compared to the axial one due to the deflection of fast-moving electrons and the persistence of two-electron temperature on the radial axis.

Magnetic Field Curves and Magnetic Equipotential Surfaces around Crossing Electrical Wires Replacing Classical Magnetic Field Lines

This article is based on a recent model specifically defining magnetic field values around electrical wires. With this model, calculations of field around parallel wires were obtained. Now, this model is extended with the new concept of magnetic equipotential surface to magnetic field curves around crossing wires. Cases of single, double, and triple wires are described. Subsequent article will be conducted for more general scenarios where wires are neither infinite nor parallel.

The influence of electric field on the photodetachment of H^- near a metal surface

The influence of electric field on the photodetachment of H- near a metal surface is investigated based on the closed-orbit theory. It is found that the photodetachment of H- near a metal surface is not only related to the electric field strength but also to the electric field direction. If the electric field is along the ＋z axis, it can strengthen the oscillation in the photodetachment cross section. However, if the electric field is along the -z axis, since the direction of electric field force is opposite to that of static-image force caused by the metal surface, the situation becomes much more complicated. When the electric field is very weak, its influence can be neglected. The photodetachment cross section is nearly the same as that when a single metal surface exists. When the electric field strength is strong enough, the electric field force is able to counteract the metallic attraction, therefore no closed orbit is formed. If the electric field continues to increase until its influence becomes dominant, the photodetachment cross section approaches the case of the photodetachment of H^- in an electric field. Our results may be useful for guiding future experimental studies on the photodetachment of negative ions near surfaces.

Influence of non-uniform electric field distribution on the atmospheric pressure air dielectric barrier discharge

The dielectric barrier discharge(DBD)in air at atmospheric pressure is not suitable for industrial applications due to its randomly distributed discharge filaments.In this paper,the influence of the electric field distribution on the uniformity of DBD is theoretically analyzed and experimentally verified.It is found that a certain degree of uneven electric field distributions can control the development of electron avalanches and regulate their transition to streamers in the gap.The discharge phenomena and electrical characteristics prove that an enhanced Townsend discharge can be formed in atmospheric-pressure air with a curved-plate electrode.The spectral analysis further confirms that the gas temperature of the plasma produced by the curved-plate electrode is close to room temperature,which is beneficial for industrial applications.This paper presents the relationship between the electron avalanche transition and the formation of a uniform DBD,which can provide some references for the development and applications of the DBD in the future.

Electron beam modeling and analyses of the electric field distribution and space charge effect

In electron beam technology, one of the critical focuses of research and development efforts is on improving the measurement of electron beam parameters. The parameters are closely related to the generation, emission, operation environment, and role of the electron beam and the corresponding medium. In this study, a field calculation method is proposed, and the electric field intensity distribution on the electron beam’s cross-section is analyzed. The characteristics of beam diffusion caused by the space charge effect are investigated in simulation, and the obtained data are compared with the experiment. The simulation demonstrated that the cross-sectional electric field distribution is primarily affected by the electron beam current, current density distribution, and electron beam propagation speed.

Surface Electrical Field Distribution Simulation and Insulation Characteristics Test of Polluted Insulators

In this paper,the electrical fields along the insulator surface under different scenarios,such as asymmetric pollution on top/bottom surface,and uneven circumferential distribution of surface pollution,have been calculated with finite element method for field simulation.Tests on artificial pollution insulators are conducted to study the 50% withstand voltage U50 of artificial pollution suspension insulators under different NSDD(non-soluble deposit density)and asymmetric pollution on the top/bottom surface,and study the change of leakage current with air humidity under different voltage and different ESDD(equivalent salt deposit density).The result shows that asymmetric top/bottom surface pollution has a greater impact on the insulator electrical field distribution,and the leakage current will jump under low air humidity,if had large ESDD,which has practical meanings to the anti-pollution design of the transmission line under different pollution levels across the country.

Local field distribution and configuration of CO molecules adsorbed on the nanostructure platinum surface

This paper shows that the local electric field distribution near the nanostructure metallic surface is obtained by solving the Laplace equation, and furthermore, the configuration of CO molecules adsorbed on a Pt nanoparticle surface is obtained by using Monte Carlo simulation. It is found that the uneven local electric field distribution induced by the nanostructure surface can influence the configuration of carbon monoxide （CO） molecules by a force, which drags the adsorbates to the poles of the nanoparticles. This result, together with our results obtained before, may explain the experimental results that the nanostructure metallic surface can lead to abnormal phenomena such as anti-absorption infrared effects.

Electric field distribution around the chain of composite nanoparticles in ferrofluids

Composite nanoparticles （NPs） have the ability of combining materials with different properties together, thus receiving extensive attention in many fields. Here we theoretically investigate the electric field distribution around core/shell NPs （a type of composite NPs） in ferrofluids under the influence of an external magnetic field. The NPs are made of cobalt （ferromagnetic） coated with gold （metallic）. Under the influence of the external magnetic field, these NPs will align along the direction of this field, thus forming a chain of NPs. According to Laplace＇s equations, we obtain electric fields inside and outside the NPs as a function of the incident wavelength by taking into account the mutual interaction between the polarized NPs. Our calculation results show that the electric field distribution is closely related to the resonant incident wavelength, the metallic shell thickness, and the inter-particle distance. These analytical calculations agree well with our numerical simulation results. This kind of field-induced anisotropic soft-matter systems offers the possibility of obtaining an enhanced Raman scattering substrate due to enhanced electric fields.

Influence of the channel electric field distribution on the polarization Coulomb field scattering in In_(0.18) Al_(0.82) N/AlN/GaN heterostructure field-effect transistors

By making use of the quasi-two-dimensional （quasi-2D） model, the current-voltage （l-V） characteristics of In0AsA10.82N/A1N/GaN heterostructure field-effect transistors （HFETs） with different gate lengths are simulated based on the measured capacitance-voltage （C-V） characteristics and I-V characteristics. By analyzing the variation of the electron mobility for the two-dimensional electron gas （2DEG） with electric field, it is found that the different polarization charge distributions generated by the different channel electric field distributions can result in different polarization Coulomb field scatterings. The difference between the electron mobilities primarily caused by the polarization Coulomb field scatterings can reach up to 1522.9 cm2/V.s for the prepared In0.38AI0.82N/A1N/GaN HFETs. In addition, when the 2DEG sheet density is modulated by the drain-source bias, the electron mobility presents a peak with the variation of the 2DEG sheet density, the gate length is smaller, and the 2DEG sheet density corresponding to the peak point is higher.

Self-screening of the polarized electric field in wurtzite gallium nitride along[0001]direction

The strong polarization effect of GaN-based materials is widely used in high-performance devices such as white-lightemitting diodes(white LEDs),high electron mobility transistors(HEMTs),and GaN polarization superjunctions.However,the current researches on the polarization mechanism of GaN-based materials are not sufficient.In this paper,we studied the influence of polarization on electric field and energy band characteristics of Ga-face GaN bulk materials by using a combination of theoretical analysis and semiconductor technology computer-aided design(TCAD) simulation.The selfscreening effect in Ga-face bulk GaN under ideal and non-ideal conditions is studied respectively.We believe that the formation of high-density two-dimensional electron gas(2 DEG) in GaN is the accumulation of screening charges.We also clarify the source and accumulation of the screening charges caused by the GaN self-screening effect in this paper and aim to guide the design and optimization of high-performance GaN-based devices.

Off-Shore Sea Surface Electric Field Investigations around the Indian Sub-Continent during 9-20 May 1983

Sea surface electric field observations off the coast from Goa (15°25'N, 73°47'E) to Madras (13°04'N, 80°15'E) around Sri Lanka, in a distance range 25-135 km from coast, during 9-20 May 1983 were taken. In this paper we have examined the diurnal variation of electric field in the Arabian Sea, Indian Ocean and Bay of Bengal regions covered during the cruise of the research ship ORV Gaveshani. An aspect of electric field dependence on coastal distance and Aitken Nuclei concentration has also been studied. An attempt to examine the latitude dependence of field was also made. Results obtained in the above studies are presented and compared with those obtained elsewhere.

Impact of the Evolution of a Curved Charge Distribution on Electric Field

Theoretically, it is plausible to assume for a chosen charge distribution the electric field can be calculated. However, in practice depending on the geometry of the distribution one faces mathematical challenges. In this research- oriented project, we select a set of related familiar 2D geometric curves addressing the mathematical issues. Specifically, we consider a family of curves that evolved via step-by-step “evolution”. The evolution begins from a segment of a circular arc to a complete circle. The electric fields are formulated, evaluated, and graphed. Accomplishing these objectives relied heavily on utilizing a Computer Algebra System (CAS), specifically Mathematica [1]. The CPU’s expensive runtimes are circumvented by introducing mathematical procedures.

Impact of a Mobile Void within a Charge Distribution on the Electric Field

The electric field of a 3D spherical uniform charge distribution embodying a spherical mobile void at an exterior point is calculated. The size of the void and its path is arbitrary. Specifically, three different trajectories are analyzed. The movement of the void impacts the electric field so that the field becomes time-dependent. In terms of the chosen path and the size of the bubble, we evaluate the time-dependent electric field. The time profile of the field is calculated. Because of the computational challenges, the most of calculation is carried out utilizing a Computer Algebra System (CAS), specifically Mathematica [1]. This project makes the CAS an essential tool not only for calculating the field but for animating the features of the mobile void. An atlas of the study cases is included.

Distribution of Electrical Field Energy for Conversion of Methane to C_2 Hydrocarbons via Dissymmetrical Electric Field Enhanced Plasma

Direct conversion of methane into C2 hydrocarbons through alternating current electric field enhanced plasma was studied under room temperature, atmospheric pressure and low power conditions. The distribution of electrical field intensity and distribution of energy were calculated with software that was developed by us according to the charge simulation method. The results indicated that the energy of tip of electrode was 0.36 J/mm^3 and it was higher than the methane dissociation energy （0.0553 J/mm^3）. The methane located at this area can be activated easily. The higher-energy particles produced by dissociation collided with molecules around them and initiated consecutive reactions between free radicals and molecules. The method was proved to be valided and could be taken as a basis for the electrical field study concerned.

Terahertz Electric Field Induced Double Strand Breakage and Vibrations of dsDNA in a Gold Nanoslit

Objective This work examines the impact of external electric fields at terahertz(THz)frequencies on doublestranded deoxyribonucleic acid(dsDNA)systems adsorbed on Au(111)surfaces in aqueous environments.Methods The investigation utilizes a molecular dynamics(MD)approach at the atomic level and vibrational dynamics calculations using the GolDNA-Amber force field.Results The results reveal that the sugar-phosphate backbone of the DNA exhibits reduced adherence to the gold surface,while the side chains display a stronger affinity.When subjecting the hydrated DNA strands to an electric field with frequencies up to 10 THz,peak intensities of vibrational dynamic density(VDoS)are observed at five different frequencies.Moreover,the strong electric field causes hydrogen bonds in the DNA within the slit to break.The sensitivity to the electric field is particularly pronounced at 8.8 THz and 9.6 THz,with different vibrational modes observed at varying electric field strengths.Conclusion These findings contribute to an enhanced understanding of the molecular organization of gold-plated charged biological interfaces.

Photodetachment of negative ion in a gradient electric field near a metal surface

Based on closed-orbit theory, the photodetachment of H- in a gradient electric field near a metal surface is studied. It is demonstrated that the gradient electric field has a significant influence on the photodetachment of negative ions near a metal surface. With the increase of the gradient of the electric field, the oscillation in the photodetachment cross section becomes strengthened. Besides, in contrast to the photodetachment of H- near a metal surface in a uniform electric field, the oscillating amplitude and the oscillating region in the cross section of a gradient electric field also become enlarged. Therefore, we can use the gradient electric field to control the photodetachment of negative ions near a metal surface. We hope that our results will be useful for understanding the photodetachment of negative ions in the vicinity of surfaces, cavities, and ion traps.

An AlGaN/GaN HEMT with a reduced surface electric field and an improved breakdown voltage

A reduced surface electric field in an AlGaN/GaN high electron mobility transistor （HEMT） is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas （2-DEG） channel as an electric field shaping layer. The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions. Compared with the HEMTs with conventional sourceconnected field plates and double field plates, the HEMT with a Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge. By optimizing both the length of Mg-doped layer, Lm, and the doping concentration, a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure, respectively. In a device with VGS = -5 V, Lm 1.5 m, a peak Mg doping concentration of 8×10^17 cm-3 and a drift region length of 10 m, the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.

Electric field distribution and effective nonlinear AC and DC responses of graded cylindrical composites

The perturbation method is used to study the localization of electric field distribution and the effective nonlinear response of graded composites under an external alternating-current（AC） and direct-current（DC） electric field E app = E 0（1 ＋ sin ωt）.The dielectric profile of the cylindrical inclusions is modeled by function ε i（r） = C k r k（r ≤ a）,where r is the radius of the cylindrical inclusion,and C k,k,a are parameters.In the dilute limit,the local potentials and the effective nonlinear responses at all harmonics are derived.Meanwhile,the general effective nonlinear responses are also derived and compared with the effective nonlinear responses at harmonics under the AC and DC external field.It is found that the effective nonlinear AC and DC responses at harmonics can be calculated by those of the general effective nonlinear of the graded composites under the external DC electric field.Moreover,the obtained local electrical fields show that the electrical field distribution in the cylindrical inclusions is controllable,and the maximum of the electric field inside the cylinder is at its center.