Controller Design for Electric Power Steering System Using T-S Fuzzy Model Approach

Pressure ripples in electric power steering （EPS） systems can be caused by the phase lag between the driver s steering torque and steer angle, the nonlinear frictions, and the disturbances from road and sensor noise especially during high-frequency maneuvers. This paper investigates the use of the robust fuzzy control method for actively reducing pressure ripples for EPS systems. Remarkable progress on steering maneuverability is achieved. The EPS dynamics is described with an eight-order nonlinear state-space model and approximated by a Takagi-Sugeno （T-S） fuzzy model with time-varying delays and external disturbances. A stabilization approach is then presented for nonlinear time-delay systems through fuzzy state feedback controller in parallel distributed compensation （PDC） structure. The closed-loop stability conditions of EPS system with the fuzzy controller are parameterized in terms of the linear matrix inequality （LMI） problem. Simulations and experiments using the proposed robust fuzzy controller and traditional PID controller have been carried out for EPS systems. Both the simulation and experiment results show that the proposed fuzzy controller can reduce the torque ripples and allow us to have a good steering feeling and stable driving.

Precise Compound Control of Loading Force for Electric Load Simulator of Electric Power Steering Test Bench

Electric load simulator(ELS) systems are employed for electric power steering(EPS) test benches to load rack force by precise control. Precise ELS control is strongly influenced by nonlinear factors. When the steering motor rapidly rotates, extra force is directly superimposed on the original static loading error, which becomes one of the main sources of the final error. It is key to achieve ELS precise loading control for the entire EPS test bench. Therefore, a three-part compound control algorithm is proposed to improve the loading accuracy. First, a fuzzy proportional–integral plus feedforward controller with force feedback is presented. Second, a friction compensation algorithm is established to reduce the influence of friction. Then, the relationships between each quantity and the extra force are analyzed when the steering motor rapidly rotates, and a net torque feedforward compensation algorithm is proposed to eliminate the extra force. The compound control algorithm was verified through simulations and experiments. The results show that the tracking performance of the compound control algorithm satisfies the demands of engineering practice, and the extra force in the ELS system can be suppressed by the net torque corresponding to the actuator’s acceleration.

H∞ control of novel active steering integrated with electric power steering function

Based on the traditional active steering system, a novel active steering system integrated with electric power steering function was introduced, which can achieve the functions of both active steering and electric power steering. In view of the interference from road random signal and sensor noise in the novel active steering system, the H∞ control model of the novel active steering system was built. With satisfying steering feel, good robust performance and steering stability being the control objectives, the H∞ controller for the novel active front steering (AFS) system was designed. The simulation results show that the novel AFS system with H∞ control strategy can attenuate the road interference quickly, and there is no resonance peak in the bode diagram. It can make the driver obtain more useful information in the low frequency range, and attenuate the road interference better in the high frequency range, thus the driver can get more satisfying road feeling. Therefore, the designed H∞ controller can synthesize the advantages of both robust performance and robust stability, and has certain contribution to the design of novel AFS system.

Recent Developments of Modulation and Control for High-Power Current-Source-Converters Fed Electric Machine Systems

The pulse-width-modulated(PWM)current-source converters(CSCs)fed electric machine systems can be considered as a type of high reliability energy conversion systems,since they work with the long-life DC-link inductor and offer high fault-tolerant capability for short-circuit faults.Besides,they provide motor friendly waveforms and four-quadrant operation ability.Therefore,they are suitable for high-power applications of fans,pumps,compressors and wind power generation.The purpose of this paper is to comprehensively review recent developments of key technologies on modulation and control of high-power(HP)PWM-CSC fed electric machines systems,including reduction of low-order current harmonics,suppression of inductor–capacitor(LC)resonance,mitigation of common-mode voltage(CMV)and control of modular PWM-CSC fed systems.In particular,recent work on the overlapping effects during commutation,LC resonance suppression under fault-tolerant operation and collaboration of modular PMW-CSCs are described.Both theoretical analysis and some results in simulations and experiments are presented.Finally,a brief discussion regarding the future trend of the HP CSC fed electric machines systems is presented.

A New Coordinated Fuzzy-PID Controller for Power System Considering Electric Vehicles

With penetration growing of renewable energy sources which integrated into power system have caused problems on grid stability. Electric Vehicles (EV) are one of the renewable energy sources that can bring significant impacts to power system during their charging and discharging operations. This article established a model of single machine infinite bus (SMIB) power system considering EV as a case study of load disturbance for power system oscillation. The objective of this research is to enhance stability and overcome the drawbacks of traditional control algorithms such as power system stabilizer (PSS), PID controller and fuzzy logic controller (FLC). The implementation’s effect of FLC parallel with PID controller (Fuzzy-PID) has been shown in this paper. The speed deviation (?ω) and electrical power (Pe) are the important factors to be taken into consideration without EV (only change in mechanical torque), EV with change in the mechanical torque and sudden plug-in EV. The obtained result by nonlinear simulation using Matlab/Simulink of a SMIB power system with EV has shown the effectiveness of using (Fuzzy-PID) against all disturbances.

The Application of Principle of Automatic Control in the site Management of Electric Power Construction Enterprise

It is need to establish site project department during the construction of electric power project.The head office should design and build the main structure,continually improve structure of project department,meantime,positively apply principle of automatic control to improve the site management of electric power construction.In this article,the application strategy of principle of automatic control is analyzed focusing on the site work of electric power construction.

The Combination of Two Control Strategies for Series Hybrid Electric Vehicles

With most countries paying attention to the environment protection, hybrid electric vehicles have become a focus of automobile research and development due to the characteristics of energy saving and low emission. Power follower control strategy(PFCS) and DC-link voltage control strategy are two sorts of control strategies for series hybrid electric vehicles(HEVs). Combining those two control strategies is a new idea for control strategy of series hybrid electric vehicles. By tuning essential parameters which are the defined constants under DClink voltage control and under PFCS, the points of minimum mass of equivalent fuel consumption(EFC) corresponding to a series of variables are marked for worldwide harmonized light vehicles test procedure(WLTP). The fuel economy of series HEVs with the combination control schemes performs better compared with individual control scheme. The results show the effects of the combination control schemes for series HEVs driving in an urban environment.

Battery Charger for Electric Vehicles based on a Wireless Power Transmission

In this paper,the case of a battery charger for electric vehicles based on a wireless power transmission is addressed.The specificity of every stage of the overall system is presented.Based on calculated and measured results,relevant capacitive compensations of the transformer and models are suggested and discussed in order to best match the operating mode and aiming at simplifying as much as possible the control and the electronics of the charger.

Study on Ultracapacitors Parameter Design and Control Strategy of Electric Bus

Based on the analysis of ultracapacitors efficiency and vehicle driving character, three conditions restricting the ultracapacitors charge/discharge time are derived. The study focuses on ultracapacitors specific design rules decided by charge/discharge time and how to integrate with battery packs and converter through ultracapacitors＇voltage and current double regulators. Through BFC6100-EV electric bus test, it is shown that the proposed method and control strategy are feasible and the system can effectively improve the bus dynamic performance and ability to receive braking energy effectively.

Comparison among Chargers of Electric Vehicle Based on Different Control Strategies

The charger of electric vehicle is a power electronic device which consists of rectifying devices and DC-DC converters. This nonlinear diode rectifier circuit has low power factor and high harmonic content. In order to improve power factor and reduce the harmonic distortion rate of the AC side current, single-phase non-controlled rectifier charger needs to install the active power factor correction device. A piece of power system analysis software which is called PSCAD is used in modeling of an EV charger which contains Boost-APFC. By means of simulation and analysis, differences of APFC characteristics between the hysteresis current control mode and average current control mode which has an influence on the power grid are compared. The consequence of simulation shows that the two control strategies achieve power factor correction and harmonic reduction requirements;Boost type power conversion circuit employs the average current control mode is better, which has following features: relatively faster settling time of the output voltage, relatively smaller overshoot, lower current harmonic distortion rate on AC side, lower switching frequency and better control effect.

An Innovative Approach in Balancing Real Power Using Plug in Hybrid Electric Vehicles

Many distribution systems operate under unbalanced loading conditions due to the connection of single phase loads to a three phase system. As PHEVs become more prevalent, it is expected that this unbalance will be further exacerbated due to the power draws from single phase chargers. Unbalanced loads reduce the overall system operating efficiency and power transfer capability of assets. In this paper, a new method of mitigating real power unbalance is suggested. It works by selecting which of the three phases that each single phase PHEV charger in a car park should be connected to. The algorithm is then tested on a simulation model of a real world distribution system. Using the balancing algorithm, balancing of the real power flowing through the feeder to the car park is accomplished.

An Improved Torque Sensorless Speed Control Method for Electric Assisted Bicycle With Consideration of Coordinate Conversion

In this paper,we propose an improved torque sensorless speed control method for electric assisted bicycle,this method considers the coordinate conversion.A low-pass filter is designed in disturbance observer to estimate and compensate the variable disturbance during cycling.A DC motor provides assisted power driving,the assistance method is based on the realtime wheel angular velocity and coordinate system transformation.The effect of observer is proved,and the proposed method guarantees stability under disturbances.It is also compared to the existing methods and their performances are illustrated through simulations.The proposed method improves the performance both in rapidity and stability.

Experimental Study on Cloud-Computing-Based Electric Power SCADA System

With the development of smart grid, the electric power supervisory control and data acquisition （SCADA） system is limited by the traditional IT infrastructure, leading to low resource utilization and poor scalability. Information islands are formed due to poor system interoperability. The development of innovative applications is limited, and the launching period of new businesses is long. Management costs and risks increase, and equipment utilization declines. To address these issues, a professional private cloud solution is introduced to integrate the electric power SCADA system, and conduct experimental study of its applicability, reliability, security, and real time. The experimental results show that the professional private cloud solution is technical and commercial feasible, meeting the requirements of the electric power SCADA system.

The General Configuration of CEV1 Electric Vehicle's Electrical System and the Design of Its Control Sequence

The general configuration of CEV1 electric vehicle’s electrical system and the design scheme of its control sequence are presented, which are modularized by using VMU as master control unit, PMU as power management unit, BMU as battery management unit. It is a rather advanced and practical general design scheme of electric vehicle, because the division of its module function is definite, which is advantage for research, manufacture and maintenance.

Electrical power assisted steering for EVs and HEVs

Electrical power assisted steering (EPAS) is one of the key components, especially for electrical vehicle. It has attracted much attention for their advantages with respect to improved fuel economy and has been widely adopted as automotive power-steering equipment in recent years. EPS (electrical power steering) controllers contain MCU (microprocessor control unit) to implement the complex control algorithms. EPS control strategy development is the core technology of the whole system. To achieve the better performance of driving, both mechanical structures and electrical structures are totally designed as a whole. Model-based development is recommended to software design. There are several trends about EPS’ future, such as high power EPS development, high voltage EPS development and steering-by-wire technology.

Study on Transformer Magnetic Biasing Control Method for AC Power Supplies

This paper presents a novel transformer magnetic biasing control method for high-power high-performance AC power supplies. Serious consequences due to magnetic biasing and several methods to overcome magnetic biasing are first discussed. The causes of the transformer magnetic biasing are then analyzed in detail. The proposed method is based on a high-pass filter inserted in the forward path and the feedforward control. Without testing magnetic biasing of transformer, this method can eliminate magnetic biasing of transformer completely in real-time waveform feedback control systems though the zero error of the Hall effect sensors varies with time and temperature. The method has already been employed in a 90KVA AC power supply. It is shown that it offers improved performance over existing ones. In this method, no sensors are used such that the zero error of the Hall effect sensors has not any influence on the system. It is simple to design and implement. Furthermore, the method is suitable for various power applications.

Distributed Model Predictive Load Frequency Control of Multi-area Power System with DFIGs

Reliable load frequency control(LFC) is crucial to the operation and design of modern electric power systems. Considering the LFC problem of a four-area interconnected power system with wind turbines, this paper presents a distributed model predictive control(DMPC) based on coordination scheme.The proposed algorithm solves a series of local optimization problems to minimize a performance objective for each control area. The generation rate constraints(GRCs), load disturbance changes, and the wind speed constraints are considered. Furthermore, the DMPC algorithm may reduce the impact of the randomness and intermittence of wind turbine effectively. A performance comparison between the proposed controller with and without the participation of the wind turbines is carried out. Analysis and simulation results show possible improvements on closed–loop performance, and computational burden with the physical constraints.

Distributed Secondary Control and Optimal Power Sharing in Microgrids

We address the control problem of microgrids and present a fully distributed control system which consists of primary controller,secondary controller,and optimal active power sharing controller.Different from the existing control structure in microgrids,all these controllers are implemented as local controllers at each distributed generator.Thus,the requirement for a central controller is obviated.The performance analysis of the proposed control systems is provided,and the finite-time convergence properties for distributed secondary frequency and voltage controllers are achieved.Moreover,the distributed control system possesses the optimal active power sharing property.In the end,a microgrid test system is investigated to validate the effectiveness of the proposed control strategies.

Applications of Serial-Parallel Compensated Resonant Topology in Wireless Charger System Used in Electric Vehicles

There are lots of factors that can influence the wireless charging efficiency in practice, such as misalignment and air-gap difference, which can also change all the charging parameters. To figure out the relationship between those facts and system, this paper presents a serial-parallel compensated(SPC) topology for electric vehicle/plug-in hybrid electric vehicle(EV/PHEV) wireless charger and provides all the parameters changing with corresponding curves. An ANSYS model is built to extract the coupling coefficient of coils. When the system is works at constant output power, the scan frequency process can be applied to wireless power transfer(WPT) and get the resonant frequency. In this way, it could determine the best frequency for system to achieve zero voltage switching status and force the system to hit the maximum transmission efficiency. Then frequency tracking control(FTC) is used to obtain the highest system efficiency. In the paper, the designed system is rated at 500 W with 15 cm air-gap, the overall efficiency is 92%. At the end, the paper also gives the consideration on how to improve the system efficiency.

Smart Meter Development for Cloud-Based Home Electricity Monitor System

Αcloud-based home electricity data-monitoring system,which is based on an Arduino Mega controller,is proposed for monitoring the electricity consumption(electrical power)and power quality(PQ)in home.This system is also capable of monitoring the fundamental frequency and supply-voltage transients to ensure that the appliances operate in a safe operation range.The measured data(voltage and current)are transmitted through a Wi Fi device between the Arduino controller and server.The transmission control protocol(TCP)server is set up to acquire the high-data transmission rate.The server system immediately displays the calculated parameters and the waveform of the acquired signal.A comparison with a standard measurement device shows that the proposed system,which can be built at a low cost,exhibits the same functions as a factory product.