To prepare high wear resistance and high hardness coatings, electro-spark deposition was adopted for depositing an electrode of a mixture of 92wt%WC＋8wt%Co on a cast steel roll substrate. The coating was characterize...To prepare high wear resistance and high hardness coatings, electro-spark deposition was adopted for depositing an electrode of a mixture of 92wt%WC＋8wt%Co on a cast steel roll substrate. The coating was characterized by classical X-ray diffractometer （XRD） and scanning electron microscopy （SEM） with energy dispersive X-ray analysis （EDX）. The results indicate that the coating shows nanosized particulate structure and dendritic structure including columnar structure and equiaxed structure. The primary phases of the coating contain Fe3W3C, Co3W3C, Fe2C and Si2W. The coating has a low friction coefficient of 0.13, its average wear-resistance is 3.3 times that of the cast steel roll substrate and the main mechanism is abrasive wear. The maximum microhardness value of the coating is about 1573.9 Hv0.3. The study reveals that the electro-spark deposition process has the characteristic of better coating quality and the coating has higher wear resistance and hardness.展开更多
The cobalt-based alloy coating with different Co contents was deposited on 45 steel by electro-spark deposition with the self-made electrode. The coating has a compact and uniform microstructure with low porosity and ...The cobalt-based alloy coating with different Co contents was deposited on 45 steel by electro-spark deposition with the self-made electrode. The coating has a compact and uniform microstructure with low porosity and no visible microcracks. When Co content increases grad- ually, oxygen content of coating samples 1-5 decreases first and then increases in the range of 2.52 wt%-3.05 wt%; sample 3 has the lowest oxygen content of 2.52 %. Mi- crohardness of the coating is improved remarkably com- pared with the substrate （HV 230.18）. With Co content increasing, microhardness of the coating samples 1-5 first rises slightly and then declines rapidly in the range of HV 580.61-1052.33. Sample 3 gets the maximum of HV 1052.33, which is about 4.6 times that of the substrate. The coating presents excellent wear resistance, which first increases and then decreases when Co content increases. Sample 3 shows the best wear resistance of about 6.4 times that of the substrate. Main wear mechanism of the coating is abrasive wear and fatigue wear, along with oxidation wear under high speed or heavy load conditions.展开更多
Electro-spark deposition has been carried out on the 35CrMo steel by filling and restoring the simulated slot specimens, and continuous surface coating with extra low porosity was obtained with proper parameters. The ...Electro-spark deposition has been carried out on the 35CrMo steel by filling and restoring the simulated slot specimens, and continuous surface coating with extra low porosity was obtained with proper parameters. The microstructure transformation and interface behavior of deposited joint were observed and analyzed. It shows that a transition region with 15μm in depth was obtained between base metal and deposited metal, and metallurgical bonding was achieved between restored base metal and deposition coating.展开更多
Electro-spark deposition（ESD） was adopted for preparing high property coatings by depositing WC-8Co cemented carbide on an spheroidal graphite roll substrate.The microstructure and properties of the coating were inv...Electro-spark deposition（ESD） was adopted for preparing high property coatings by depositing WC-8Co cemented carbide on an spheroidal graphite roll substrate.The microstructure and properties of the coating were investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） with energy dispersive X-ray（EDX） and ball-disc configuration wear tester.The results show that nanosized particles and amorphous structures prevail in the coating which is metallurgically bonded to the substrate.The microstructures of the transition zone include columnar structure and equiaxed structure.The primary phases of the coating contain W2C, W6C2.54, Fe3W3C, and Co3W3C.The results of abrasive test show that the coating has low friction coefficients（μaverage = 0.18） and the wear mechanisms are mainly abrasive wear, fatigue wear, and oxidation wear.The maximum microhardness value of the coating is about 17410 N/mm2.The study reveals that the electro-spark deposition process has better coating quality and the coating has high wear resistance and hardness.展开更多
Nickel-base superalloy components with high Al+Ti content are difficult to weld repair using high strength filler materials with conventional welding methods like TIG welding. A feasibility study of electro-spark depo...Nickel-base superalloy components with high Al+Ti content are difficult to weld repair using high strength filler materials with conventional welding methods like TIG welding. A feasibility study of electro-spark deposition (ESD) for unweldable superalloy component repair with a high strength filler material was carried out. SEM analysis reveals that a fully dense, crack-free, metallurgical bonded deposition layer can be obtained on the K24 substrate. The as-deposited microstructure characterizes fine cellular structure and the post weld heat treatment precipitates fine γ′particles. The room temperature tensile testing and 975℃, 196MPa stress rupture life testing indicate that ESD makes positively contribution to mechanical performance of repaired specimens. Based on these results, ESD has the potential as an effective alternative to repair of damage and defects in superalloy components, but more efforts should be made before it can be applied in engineering repair.展开更多
This paper studies the mechanism of formation of the deposit layer by (ESD) electro-spark deposition process. Inconel 738 substrates are coated with a deposited layer of NI6625 (Inconel 625). Selections of these two a...This paper studies the mechanism of formation of the deposit layer by (ESD) electro-spark deposition process. Inconel 738 substrates are coated with a deposited layer of NI6625 (Inconel 625). Selections of these two alloys have been done because they had wide applications and importance in the industry especially in gas turban blades in inland stations and in aircraft engines. ESD is suggested because it has a low input heat process which eliminates the effect of HAZ in these Ni-superfluous due to their sustainability to micro-cracks. The coating contains many deposited sub-layers coming from evaporated and melted micro-regions as a result of locally high heat generated by discharging a series of capacitors charged and discharged in a controlled manner between electrode and substrate material. The maximum deposition rates at the beginning of the process and decreases until been in a steady state condition due to the nature of the resultant morphology of the created surface.展开更多
采用真空电弧熔炼法制备直径为7 mm AlCrNiFeTi高熵合金(high-entropy alloy,HEA)作为电极,使用电火花沉积技术在304不锈钢表面成功制备了AlCrNiFeTi高熵合金涂层。通过XRD、OM、EDS、SEM、显微硬度计、摩擦磨损试验机对涂层的微观组织...采用真空电弧熔炼法制备直径为7 mm AlCrNiFeTi高熵合金(high-entropy alloy,HEA)作为电极,使用电火花沉积技术在304不锈钢表面成功制备了AlCrNiFeTi高熵合金涂层。通过XRD、OM、EDS、SEM、显微硬度计、摩擦磨损试验机对涂层的微观组织结构和摩擦磨损性能进行研究。结果表明,AlCrNiFeTi电极与涂层均以BCC1和BCC2简单固溶体为主,电极微观组织结构呈典型的树枝晶。涂层由沉积点堆叠铺展形成,表面均匀致密呈橘皮状、凸凹不平,为喷溅花样展开,涂层截面结构无宏观缺陷,厚度约为59.67μm。AlCrNiFeTi涂层最大显微硬度为587.3HV0.2,比基材的硬度提高了约2.45倍。随着载荷的增大,涂层的磨损机制由氧化磨损和轻微磨粒磨损转变为磨粒磨损和黏着磨损。当摩擦载荷为5 N时,磨损率为1.213×10^(-3)mm^(3)/(N·m),摩擦因数仅为0.446,涂层的磨损率较基材的磨损率减小了约28.3%。展开更多
基金supported by the International Science and Technology Cooperation Project of the Ministry of Science and Technology of China (No.2006DFA52240)
文摘To prepare high wear resistance and high hardness coatings, electro-spark deposition was adopted for depositing an electrode of a mixture of 92wt%WC＋8wt%Co on a cast steel roll substrate. The coating was characterized by classical X-ray diffractometer （XRD） and scanning electron microscopy （SEM） with energy dispersive X-ray analysis （EDX）. The results indicate that the coating shows nanosized particulate structure and dendritic structure including columnar structure and equiaxed structure. The primary phases of the coating contain Fe3W3C, Co3W3C, Fe2C and Si2W. The coating has a low friction coefficient of 0.13, its average wear-resistance is 3.3 times that of the cast steel roll substrate and the main mechanism is abrasive wear. The maximum microhardness value of the coating is about 1573.9 Hv0.3. The study reveals that the electro-spark deposition process has the characteristic of better coating quality and the coating has higher wear resistance and hardness.
基金financially supported by the National Natural Science Foundation of China (No. 50875261)
文摘The cobalt-based alloy coating with different Co contents was deposited on 45 steel by electro-spark deposition with the self-made electrode. The coating has a compact and uniform microstructure with low porosity and no visible microcracks. When Co content increases grad- ually, oxygen content of coating samples 1-5 decreases first and then increases in the range of 2.52 wt%-3.05 wt%; sample 3 has the lowest oxygen content of 2.52 %. Mi- crohardness of the coating is improved remarkably com- pared with the substrate （HV 230.18）. With Co content increasing, microhardness of the coating samples 1-5 first rises slightly and then declines rapidly in the range of HV 580.61-1052.33. Sample 3 gets the maximum of HV 1052.33, which is about 4.6 times that of the substrate. The coating presents excellent wear resistance, which first increases and then decreases when Co content increases. Sample 3 shows the best wear resistance of about 6.4 times that of the substrate. Main wear mechanism of the coating is abrasive wear and fatigue wear, along with oxidation wear under high speed or heavy load conditions.
文摘Electro-spark deposition has been carried out on the 35CrMo steel by filling and restoring the simulated slot specimens, and continuous surface coating with extra low porosity was obtained with proper parameters. The microstructure transformation and interface behavior of deposited joint were observed and analyzed. It shows that a transition region with 15μm in depth was obtained between base metal and deposited metal, and metallurgical bonding was achieved between restored base metal and deposition coating.
基金supported by the International Science and Technology Cooperation Project of the Ministry of Science and Technology of China (No. 2006DFA52240)
文摘Electro-spark deposition（ESD） was adopted for preparing high property coatings by depositing WC-8Co cemented carbide on an spheroidal graphite roll substrate.The microstructure and properties of the coating were investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） with energy dispersive X-ray（EDX） and ball-disc configuration wear tester.The results show that nanosized particles and amorphous structures prevail in the coating which is metallurgically bonded to the substrate.The microstructures of the transition zone include columnar structure and equiaxed structure.The primary phases of the coating contain W2C, W6C2.54, Fe3W3C, and Co3W3C.The results of abrasive test show that the coating has low friction coefficients（μaverage = 0.18） and the wear mechanisms are mainly abrasive wear, fatigue wear, and oxidation wear.The maximum microhardness value of the coating is about 17410 N/mm2.The study reveals that the electro-spark deposition process has better coating quality and the coating has high wear resistance and hardness.
文摘Nickel-base superalloy components with high Al+Ti content are difficult to weld repair using high strength filler materials with conventional welding methods like TIG welding. A feasibility study of electro-spark deposition (ESD) for unweldable superalloy component repair with a high strength filler material was carried out. SEM analysis reveals that a fully dense, crack-free, metallurgical bonded deposition layer can be obtained on the K24 substrate. The as-deposited microstructure characterizes fine cellular structure and the post weld heat treatment precipitates fine γ′particles. The room temperature tensile testing and 975℃, 196MPa stress rupture life testing indicate that ESD makes positively contribution to mechanical performance of repaired specimens. Based on these results, ESD has the potential as an effective alternative to repair of damage and defects in superalloy components, but more efforts should be made before it can be applied in engineering repair.
文摘This paper studies the mechanism of formation of the deposit layer by (ESD) electro-spark deposition process. Inconel 738 substrates are coated with a deposited layer of NI6625 (Inconel 625). Selections of these two alloys have been done because they had wide applications and importance in the industry especially in gas turban blades in inland stations and in aircraft engines. ESD is suggested because it has a low input heat process which eliminates the effect of HAZ in these Ni-superfluous due to their sustainability to micro-cracks. The coating contains many deposited sub-layers coming from evaporated and melted micro-regions as a result of locally high heat generated by discharging a series of capacitors charged and discharged in a controlled manner between electrode and substrate material. The maximum deposition rates at the beginning of the process and decreases until been in a steady state condition due to the nature of the resultant morphology of the created surface.
文摘采用真空电弧熔炼法制备直径为7 mm AlCrNiFeTi高熵合金(high-entropy alloy,HEA)作为电极,使用电火花沉积技术在304不锈钢表面成功制备了AlCrNiFeTi高熵合金涂层。通过XRD、OM、EDS、SEM、显微硬度计、摩擦磨损试验机对涂层的微观组织结构和摩擦磨损性能进行研究。结果表明,AlCrNiFeTi电极与涂层均以BCC1和BCC2简单固溶体为主,电极微观组织结构呈典型的树枝晶。涂层由沉积点堆叠铺展形成,表面均匀致密呈橘皮状、凸凹不平,为喷溅花样展开,涂层截面结构无宏观缺陷,厚度约为59.67μm。AlCrNiFeTi涂层最大显微硬度为587.3HV0.2,比基材的硬度提高了约2.45倍。随着载荷的增大,涂层的磨损机制由氧化磨损和轻微磨粒磨损转变为磨粒磨损和黏着磨损。当摩擦载荷为5 N时,磨损率为1.213×10^(-3)mm^(3)/(N·m),摩擦因数仅为0.446,涂层的磨损率较基材的磨损率减小了约28.3%。
