Effect of wear conditions on tribological properties of electrolessly-deposited Ni-P-Gr-SiC hybrid composite coating

The friction and wear properties of the electrolessly-deposited Ni-P-Gr-SiC composites were investigated. The effects of graphite content, load and rotation speed on the friction coefficient and wear resistance of the composite coatings were mainly investigated. The worn surface and cross section of the coatings were characterized by scanning electron microscopy and energy-dispersive X-ray analysis. The results show that the composite coatings reveal good antifriction and wear resistance due to the synergic effect of graphite and SiC particles. The formation of graphite-rich mechanically mixed layer （GRMML） on the surface of Ni-P-Gr-SiC coating contributes to the good tribological behavior of the wear counterparts and SiC particles play a load bearing role in protecting GRMML from shearing easily.

Preparation and Tribological Properties of Ni-P Electroless Composite Coating Containing Potassium Titanate Whisker

Nickel-phosphorus （Ni-P） composite coatings containing potassium titanate （K2Ti6O13） whiskers （PTWs） were prepared by electroless plating. The surface morphology and component of coatings were investigated by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDX）, respectively before and after wear test. The tribological performance was evaluated using a pin-on-disk wear tester under dry conditions. It is found that the Ni-P-PTWs composite coatings exhibit higher wear resistance than Ni-P and Ni-P-SiC electroless coatings. The favorable effects of PTWs on the tribological properties of the composite coatings are attributed to the super-strong mechanical properties and the specific tunneling structures of PTWs. The PTWs greatly reinforce the structure of the Ni-P-based composite coatings and thereby greatly reduce the adhesive and plough wear of Ni-P-PTWs composite coatings.

Studies on electroless Ni-P-Cr_2O_3 and Ni-P-SiO_2 composite coatings

本文对化学镀镍及化学镀镍磷基质中SiO2与Cr2O3的共沉积进行了研究。微粒在不断生长的膜层中共沉积引起了新的化学复合镀层的出现,这些复合镀层许多都具有优异的耐磨及耐蚀性能。通过选取镀层合金/复合微粒/金属基体的组分可改进镀层,获得所需的性能,以满足特别的需求。在对这些复合镀层的应用需求正在迫近与增长的同时,其市场正在迅速扩张。本文开发出了一种合适的复合化学镀镍液,并通过维氏硬度法对化学复合镀镍层进行了表征。采用动电位极化及交流阻抗法测定了镀层的Taber耐磨性能及耐蚀性能。采用SEM及XRD对复合镀层的表面形貌进行了分析。

Preparation and tribological performances of Ni-P-multi-walled carbon nanotubes composite coatings

Multi-walled carbon nanotubes （MWNTs） were wet-milled in the presence of ammonia and cationic surfactant and then used as reinforcements to prepare Ni-P-MWNTs composite coatings by electroless plating. The tribological performances of the composite coatings under dry condition were investigated in comparison with 45 steel and conventional Ni-P coating, Micrographs show that short MWNTs with uniform length and open tips were obtained through the wet-milling process. The results of wear test reveal that the Ni-P-MWNTs composite coatings posses much better friction reduction and anti-wear performances when compared with 45 steel and Ni-P coating. Within the MWNTs content range of 0.74%-1.97%, the friction coefficient and the volume wear rate of the composite coatings decrease gradually and reach the minimum values of 0.08 and 6.22x10-15 m3/（N.m）, respectively. The excellent tribological performances of the composite coatings can be attributed to the introduction of MWNTs, which play both roles of reinforcements and solid lubricant during the wear process.

Erosion and Toughening Mechanisms of Electroless Ni-P-Nano-NiTi Composite Coatings on API X100 Steel under Single Particle Impact

The addition of superelastic NiTi to electroless Ni-P coating has been found to toughen the otherwise brittle coatings in static loading conditions, though its effect on erosion behaviour has not yet been explored. In the present study, spherical WC-Co erodent particles were used in single particle impact testing of Ni-P-nano-NiTi composite coatings on API X100 steel substrates at two average velocities—35 m/s and 52 m/s. Erosion tests were performed at impact angles of 30°, 45°, 60°, and 90°. The effect of NiTi concentration in the coating was also examined. Through examination of the impact craters and material response at various impact conditions, it was found that the presence of superelastic NiTi in the brittle Ni-P matrix hindered the propagation of cracks and provided a barrier to crack growth. The following toughening mechanisms were identified: crack bridging and deflection, micro-cracking, and transformation toughening.

Electroless plating Ni-P matrix composite coating reinforced by carbon nanotubes

Ni-P matrix composite coating reinforced by carbon nanotubes (CNTs) was deposit ed by electroless plating. The most important factors that influence the content of carbon nanotubes in deposits,such as agitation,surfactant and carbon nanot ubes concentration in the plating bath were investigated. The surface morphology,structure and properties of the Ni-P-CNTs coating were examined. It is found that the maximum content of carbon nanotubes in the deposits is independent of carbon nanotubes concentration in the plating bath when it is up to 5 mg/L. The test results show that the carbon nanotubes co-deposited do not change the str ucture of the Ni-P matrix of the composite coating,but greatly increase the ha rdness and wear resistance and decrease the friction coefficient of the Ni-P-C NTs composite coating with increasing content of carbon nanotubes in deposits.

Influence of vacuum heat treatment on structure and micro-hardness of electroless Ni-P-SiC composite coating

The electroless Ni-P-SiC composite coatings were prepared and the influence of vacuum heat treatment on its structure and properties was analyzed. The Ni-P-SiC composite coatings were characterized by morphology,structure and micro-hardness. The morphology and structure of the Ni-P-SiC composite coatings were studied by scanning electron microscopy(SEM) and X-ray diffractometry(XRD),respectively. A great deal of particles incorporation and uniform distribution were found in Ni-P-SiC composite coatings. XRD results show a broad peak of nickel and low intensity SiC peaks present on as-deposited condition. Micro-hardness of as-deposited Ni-P-SiC composite coatings is improved greatly,and the best micro-hardness is obtained after heat treatment in a high vacuum at 400 ℃ .

Wear Behaviour of Electroless Ni-P-Diamond Composite Coatings

The wear behaviour of composite coatings is related to the nature of embedded particles.The effects of particle size on the wear behaviour of composite coatings are analyzed.Electroless nickel composite coatings containing diamond particles with the sizes in the range of 0—0.5,0.5—1,1—2μm are prepared.The surface morphology of diamond particles and composite coatings are observed by scanning electron microscopy(SEM).The wear tests of composite coatings are comparatively evaluated by sliding against a cemented tungsten carbide ball.The 3D morphology of worn scar is evaluated by using a 3Dprofiler.The results show that the hardness and wear resistance of composite coatings can increase with the increase of particle sizes.The mixture mechanism of adhesive wear and abrasive wear turn into single abrasive wear with the increase of particle sizes as well.The transformation of wear behaviour is mainly attributed to particle roles during wear process.

PROCESS AND PROPERTIES OF ELECTROLESS PLATING RE-Ni-B-SiC COMPOSITE COATINGS

Technology and properties of electroless composite RE-Ni-B-SiC coatings have been investigated.Results show that stabilizer plys a decisive role in electroless composite Ni-B-SiC,the addition of appropriate quantity of RE(rare earth) into the Ni-B-SiC bath not only increases SiC content in composite coatings,their hardness and wear resistance but also improves crystalline fineness,Wear resistance increases with the increase of SiC.Hardness and wear resistance of composite coatings reach peak values a fter heat treatment at 4OO and 500℃ for 1h respectively.

ELECTROLESS PLATING COMPOSITE COATINGS OF Ni-Ti-Re ON THE SURFACE OF DIAMOND

The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2～3 μm Ti particles and trace rare earth salt to bath solution. Ti particles deposited on the surface of diamond were found by SEM and formation of TiC was verified by X ray diffraction analysis after heat treatment of the coatings in vacuum at 900 ℃. The binding strength between the coated diamond and the metal matrix was improved effectively in the diamond composite based on metal cement.

Composite Ni-Nanodiamond Coating Deposited by Electroless Method

The work in this study is focused on investigation of composite nickel coatings. The coatings were deposited on ductile cast iron samples of different composition by electroless method EFTTOM NICKEL with addition of strengthening nanodiamond particles （2-4 nm）, The samples were prepared by casting and austempering. The microstructure, microhardness and wear resistance of the coatings were investigated. The thickness of the coatings was also determined （8-10μm）. Metallographic analyses, SEM （scanning electron microscopic） investigation, microhardness measurements by knoop method, wear resistance tests were carried out. The coatings with and without heat treatment at 290℃, 6 h were tested. Duplication of microhardness value and improvement of the coating＇s properties of heat treated coatings were observed.

Characteristics of microstructure and performance of laser-treated electroless Ni-P/Ni-W-P duplex coatings

Characteristics of microstructures of electroless Ni-P/Ni-W-P duplex coatings were investigated using SEM/EDX and XRD analysis techniques. Microhardness and wear behaviour of the coatings before and after laser crystallization were evaluated by measurements of hardnesses of coating surface and cross-section, and by unlubricated friction and wear experiments. The results indicate that it is possible to prepare electroless Ni-P/Ni-W-P duplex coatings by sequential immersion in two different plating baths. After laser crystallization, the microstructures of electroless Ni-P/Ni-W-P duplex coatings present the characteristics of higher degree of crystallization and larger grain size for outer layer Ni-W-P than inner Ni-P, but outer layer has a higher hardness. The wear resistance of laser-treated duplex coatings in a given process parameter conditions is superior to the as-plated ones. Laser treatment was performed directly in air without argon protection, which provides the possibility for application of industrialized production.

Electroless plating and growth kinetics of Ni-P alloy film on SiC_p/Al composite with high SiC volume fraction

After Sn/Pd activating, the SiCp/Al composite with 65% SiC (volume fraction) was coated by electroless Ni?P alloy plating. Surface morphology of the composite and its effect on the Ni?P alloy depositing process and bonding action of Ni and P atoms in the Ni?P alloy were studied. The results show that inhomogeneous distribution of the Sn/Pd activating points results in preferential deposition of the Ni?P alloy particles on the Al alloy and rough SiC particle surfaces and in the etched caves. The Ni?P alloy film has an amorphous structure where chemical bonding between Ni and P atoms exists. After a continuous Ni?P alloy film formed, electroless Ni?P alloy plating is not affected by surface morphology and characteristics of the SiCp/Al composite any longer, but by the electroless plating process itself. The Ni?P alloy film follows linear growth kinetics with an activation energy of 68.44 kJ/mol.

Study of Electroless Ni-P-CNTs Composite Plating

The electroless Ni-P-carbon nanotubes composite plating was studied on the copper substrate. Metallurgical microscope, scanning electronic microscope, X-ray diffractometer and micro hardness tester were used to study the structure, constitution and performance of the electroless Ni-P-carbon nanotubes composite deposit. Experiential results show that, with the increment of carbon nanotubes content in electroless plating solution, the grain size on the sample surface decreases whereas the density of grains and the hardness for composite deposit increases. Moreover, adding carbon nanotubes not only improves the degree of crystallization for the composite deposit but also helps their transformation from the amorphous state to the nanocrystal state.

Mechanical assisted electroless barrel-plating Ni-P coatings on magnesium alloy

A mechanically assisted electroless barrel-plating Ni-P was carried out in a rolling drum containing Mg alloy specimens and ceramic balls, which was submerged in a bath containing electroless plating solution deposited by this novel technique have a It is demonstrated that the Ni-P coatings crystallized Ni-P solid solution structure, showing fine-grains, higher hardness, and higher corrosion resistance compared with the conventional electroless plated amorphous Ni-P coatings. After heat treatment at 400 ℃ for 1 h, the structure of such Ni-P coatings were transformed to a structure with Ni-Ni3P double phases, and cracks in these coatings could not be observed, whereas cracks appeared seriously in the conventional electroless plated Ni-P coating after same heat treatment. Therefore, both hardness and corrosion resistance of these Ni-P coatings can be improved further by heat treatment. All of these beneficial effects can be attributed to the role of mechanical attrition during the mechanically assisted electroless barrel-plating process.

Evaluation of residual stress and corrosion behaviour of electroless plated Ni-P/Ni-Mo-P coatings

Single Ni-P and Ni-Mo-P coatings as well as duplex Ni-P/Ni-Mo-P coatings with the same compositions were prepared by electroless plating.The residual stresses of the coatings on the surface and cross sections were measured by nanoindentation and AFM analysis,and the corrosion behaviour of the coatings in10%HCl solution was evaluated by electrochemical methods,to establish the correlation between the residual stresses and corrosion behaviour of the coatings.The results showed that the single Ni-P and duplex Ni-P/Ni-Mo-P coatings presented residual compressive stresses of241and206MPa respectively,while the single Ni-Mo-P coating exhibited a residual tensile stress of257MPa.The residual compressive stress impeded the growth of the pre-existing porosity in the coatings,protecting the integrity of the coating.The duplex Ni-P/Ni-Mo-P coatings had better corrosion resistance than their respective single coating.In addition,the stress states affect the corrosive form of coatings.

Wear and Corrosion Resistance of Electroless Plating Ni-P Coating on P110 Steel

In order to improve the surface performance and increase the lifetime of P 110 oil casing tube steel during operation, electroless plating was conducted to form Ni-P coating onto its surface. The surface morphology/element distribution and phase constitution of the Ni-P coating were analyzed using scanning electron microscope （SEM） equipped with energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. Tribological and electrochemical measurement tests were applied to investigate the wear and corrosion resistance of P110 steel and the Ni-P coating. The results showed that a uniform and compact, high phosphorous Ni-P coating was formed. The obtained Ni-P coating indicated certain friction-reduction effect and lower mass loss during friction-wear tests. The Ni-P coating also exhibited higher corrosion resistance in comparison with bared P 110 steel. The obtained N i-P coating has significantly improved the surface performance of P110 steel.

Microstructure and Corrosive Property of Ni-P/nano-CeO_2 Coating Electrolessly Prepared in Acidic Condition

Electroless Ni-P/nano-CeO2 composite coating was prepared in acidic condition, and its microstructure and corrosive property were compared with its CeO2-free counterpart. Scanning electronic microscopy （SEM）, transmission electronic microscopy （TEM） and differential scanning calorimeter （DSC） were used to examine surface morphology and microstructure of the coating. Aqueous corrosion was done in 3%NaCl＋5%H2SO4 solution and high temperature oxidation was done at 750 ℃ in air. The results showed that Ni-P coating had partial amorphous structure mixed with nano-crystals, while the Ni-P/CeO2 coating had perfect amorphous structure. At high temperature, Ni3P precipitation and Ni crystallization took place in both coatings at different temperatures. Aqueous corrosion property and high temperature oxidation property of the composite coating were remarkably improved due to the coating＇s microstructure change and the rare earth doping effect. During the co-deposition process, some Ce^n＋（n=3, 4） ions may be adsorbed to metal/solution interface and hinder nickel deposition. Ni-P/CeO2 coating＇s perfect amorphous structure results from the hindered crystal-typed deposition of nickel and the promoted deposition of phosphorous.

Effect of Sodium Dodecyl Sulphate on the Composition of Electroless Nickel – Yttria Stabilized Zirconia Coatings

The influence of a surfactant on the composition of nickel – yttria stabilised zirconia (YSZ) cermet coatings, applied by electroless nickel plating technique was examined. The amphiphilic characteristics of anionic surfactant sodium dodecyl sulphate (SDS), was relied upon for enhanced dispersion of YSZ particles co-deposited for use as anodes in solid oxide fuel cell technology and potential heat absorbing layers in thermal barrier coatings. Optical microscopy was employed to study the correlation between the plating thickness, level of ceramic loading and SDS concentration while the effect of the surfactant and fineness of YSZ particles on the as-deposited coating’s ceramic to metal ratio, was analysed using energy dispersive X-ray analysis (EDXA) characterisation technique.

Preparation and characterization of molybdenum powders with copper coating by the electroless plating technique

Molybdenum powders with a diameter of approximately 3 μn were coated with copper using the electroless plating technique in the pH 12.5-13 and temperature range of 55-75℃. The optimization of the electroless copper bath was evaluated through the combination of process parameters like pH and temperature. The optimized values ofpH and temperature were found to be 12.5 and 60℃, respectively, which attributes to the bright maroon color of the coating with an increase in weight of 46%. The uncoated and coated powders were subjected to microstructural studies using scanning electron microscope （SEM） and the phases were analyzed using X-my diffrction （XRD）. An attempt was made to understand the growth mechanism of the coating. The diffusion-shrinkage autocatalytic model was suggested for copper growth on the molybdenum surface.