The Electromagnetic Compatibility and Distribution of Antenna System

The mathematical model of electromagnetic compatibility and the distribution of aircraft antenna system have been investigated. The solutions of the antenna gain and electromagnetic interference margin in the regions of low frequency, resonance and high frequency were discussed. By using the basic analytical method of the EMI margin the distributed antenna system can be determined. The main program flow chart of distributed antenna design were given, and illustrated with examples of the microstrip antennas.

Electromagnetic Compatibility Design for Powertrain Control Module

In order to improve the electromagnetic compatibility of powertrain control module （PCM）, a system procedure of vehicular PCM electromagnetic alteration is presented in this paper. First of all, the box of the PCM is divided into different cabins to eliminate interferences between power supply circuit, analog circuit and digital circuit. Secondly, the working principle and electromagnetic （EM） characters of all the signals adopted by a typical PCM are analyzed. Then according to specific electromagnetic characters, different measures are adopted in corresponding signal process circuits or signal transfer cables, such as ground layout designing, power supply protecting, signal shielding and drive cable interference suppressing. Finally, further improvement may also needed regarding to practical electromagnetic compatibility test effects. The final test shows that, with all the measures mentioned above, the conducted emission of a PCM can be reduced by 20 dB; meanwhile, the radiated emission can be reduced by 30 dB comparing to the original system.

Electromagnetic Compatibility Analysis of High-Power Pulse Drive Source

Due to the widespread application in recent years, high-power pulse sources have received special attention from large companies and R & D institutions around the world. Compared with foreign mid-range and high-end products, China’s development in this field is relatively lagging behind and lacks mature mid-range and high-end products. The reason is not only because of lack of theoretical support, but more importantly, in the pursuit of indicators and design, the electromagnetic compatibility of the equipment has not been studied thoroughly, resulting in a large degree of distortion in the output waveform, resulting in a reduction in actual value. This paper introduces the sources of high-power pulsed electromagnetic interference of the main driving source, conducts a reasonable high-power electromagnetic compatibility driving source dynamic analysis, and proposes measures to improve electromagnetic compatibility.

Study of Electromagnetic Compatibility in Hospital Environments

This paper presents a study on the effects of radiation from electronic equipment in hospitals. This study was performed in Argentinean, Colombian and Spanish hospitals. The work consists of two parts: a survey to determine the hospital personnel’s knowledge of the problem and a technical part consisting of a measurements campaign to determine the levels of radiated electrical and magnetic fields in several hospitals due to the presence of electromagnetic interferences, such as the use of mobile phones. The study of this problem has been of special interest in countries such as the USA and Canada, and this paper attempts to convey the necessity of creating regulations that can be applied to the hospitals of the countries analyzed. More than fifty hospitals were studied in these three countries, considering the following aspects: the hospital personnel’s awareness of the problem, whether the hospitals have performed previous studies of this type, the appearance of problems in medical equipment due to this interference, the origin of the interference, and the failures that have appeared in computers due to electromagnetic interference. The results show that, most hospitals have a lack of knowledge regarding this issue and that field levels above those allowed by international regulations are present. Therefore, a regulation must be established to avoid the problem.

Optical E-field probe using LiNbO_3 M-Z waveguides in the electromagnetic compatibility measurements

An integrated optical E-field probe with the segmented electrode using LiNbO3 Mach-Zehnder （M-Z） waveguides is proposed and an equivalent circuit of the segmented electrode is given. According to the circuit theory, the electrode structure of the probe is designed. The unpackaged size of the fabricated probe is as small as 60× 6 × 0.5 （mm）. The measured results show that the half wavelength voltage is 7.7 V, the ±5 dB baseband range is 3 GHz, and the minimum detectable field is lower than 90 dB.μV/m （bandwidth 100 Hz）. Therefore it can be used in the electromagnetic compatibility （EMC） measurements. OCIS codes： 130.3120, 130.6010, 230.4110.

Analysis and Simulation of the Influence of Electromagnetic Fields on Living Beings near HV Power Lines Using the FDTD Method

Recent decades have seen rapid advances in the field of electrical engineering, such that our environment has become a sea of electrical and magnetic signals, raising questions about the possible effects of low-frequency electromagnetic fields on the environment and which are capable of modifying and destroying our ecosystem. Particular interest was given in this article due to a massive influx of population living near high voltage lines. The analysis and simulation of the influence of low frequency electromagnetic fields on living beings in the vicinity of high voltage sources 132 kV and 220 kV in urban areas in DR Congo is the subject of our research with a view to estimating the level of exposure of humans to low frequency electromagnetic fields. To carry out our research, we used the classic method of analyzing the field produced near a high voltage line based on Maxwell’s image theory, the Maxwell-Gauss theorem and Maxwell-Ampère theorem to model and quantify low-frequency electromagnetic fields in the vicinity of high-voltage lines. The 2D FDTD numerical formulation was developed from telegraphers’ equations and allowed us to obtain models of current and voltage induced by electromagnetic fields on living beings below and near HV lines. The different simulations carried out on the proposed models illustrate the effects of the electrical and geometric parameters of the pylons on the distribution of the electromagnetic field in the vicinity of the HV lines. The results obtained were compared to the safety limits recommended by the standards.

Filter Design of Wireless Base Station Power Supply

The design of electromagnetic interference(EMI)filters needs to fulfill the EMI standards.Designing a filter is a time-consuming process for new engineers as well as for those experienced engineers.This paper measures and compares the noise spectrum of the wireless base station power prototype with and without the original filter.The ideal insertion loss(IL)of the original filter is obtained by combining calculation and simulation.It is pointed out that the effect of the original filter is not good.Based on the improved insertion-loss method,the source impedance model of the prototype is established by combining measurement and theory.A procedure for designing EMI filters for switch power supply will be presented.The filter design procedure makes it possible to design filters quickly and easily.Finally,the proposed filter design method is proved to be effective by the EMI measurement of the wireless base station power supply prototype.

Design and Modeling of Electromagnetic Impedance Surfaces to Reduce Coupling between Antennas

We study the coupling problem of two waveguide antennas using the design of a two-dimensional inhomogeneous impedance structure with a fixed reflected field. Since this structure enables electromagnetic compatibility between antennas located on a plane, the behaviors of the electromagnetic field along the impedance structure are investigated. The method of moments is used to solve the integral equations and the numerical results are presented and analyzed. To reduce coupling between antennas, we need to take into account both the amplitude distribution of the field along the structure and in the openings of the antennas. In addition, while designing the structure, it is necessary to control the coefficient of decoupling.

Study of Electromagnetism Compatibility of Single-chip Switching Power Supply and Suppression Technique

As for the Domino effect dv/dt and electromagnetic interference during the rapid switching course of single-chip switching power supply,this article firstly analyzes electromagnetic interference source,and then diagnoses the essential interaction relationship between interference and switching activity based on the timely and area measured waveform,analyzes and studies the production mechanism and coupling path of interference mode,and sets up circuit model according to the features of transverse mode interference and common mode interference.Put forward different suppression methods finally.

Progress of Expert Systems in Electromagnetic Engineering

It is urgent to solve various problems in electromagnetic （EM） engineering under the increasingly complicated environment. Some expert systems （ES） come into being just to keep up with the demand for solving these problems. Combined with the analysis of development orES technology and the development trend of EM engineering software in recent years, the application orES technology in EM engineering is discussed, and especially the progress of complete ES in electromagnetic compatible （EMC） is introduced.

Simulation and Modeling of Common Mode EMI Noise in Planar Transformers

The transformer is the key circuit component of the common-mode noise current when an isolated converter is working.The highfrequency characteristics of the transformer have an important influence on the common-mode noise of the converter.Traditionally,the measurement method is used for transformer modeling,and a single lumped device is used to establish the transformer model,which cannot be predicted in the transformer design stage.Based on the transformer common-mode noise transmission mechanism,this paper derives the transformer common-mode equivalent capacitance under ideal conditions.According to the principle of experimental measurement of the network analyzer,the electromagnetic field finite element simulation software three-dimensional(3D)modeling and simulation method is used to obtain the two-port parameters of the transformer,extract the high-frequency parameters of the transformer,and establish its electromagnetic compatibility equivalent circuit model.Finally,an experimental prototype is used to verify the correctness of the model by comparing the experimental measurement results with the simulation prediction results.

A novel true triaxial test system for microwave-induced fracturing of hard rocks

This study introduces a test system for microwave-induced fracturing of hard rocks under true triaxial stress.The test system comprises a true triaxial stress loading system,an open-ended microwaveinduced fracturing system,a data acquisition system,an acoustic emission(AE)monitoring system,and an auxiliary specimen loading system.Microwave-induced surface and borehole fracturing tests under true triaxial stress were fulfilled for the first time,which overcomes the problem of microwave leakage in the coupling loading of true triaxial stress and microwave.By developing the dynamic monitoring system,the thermal response and fracture evolution were obtained during microwave irradiation.The monitoring system includes the infrared thermometry technique for monitoring rock surface temperature,the distributed optic fiber sensing technique for monitoring temperature in borehole in rock,the AE technique and two-dimensional digital speckle correlation technique for monitoring the evolution of thermal damage and the rock fracturing process.To validate the advantages of the test system and investigate the characteristics of microwave-induced fracturing of hard rocks,the study demonstrates the experimental methods and results for microwave-induced surface and borehole fracturing under true triaxial stress.The results show that thermal cracking presented intermittent characteristics(calm eactiveecalm)during microwave-induced surface and borehole fracturing of basalt.In addition,true triaxial stress can inhibit the development and distribution of thermal cracks during microwave-induced surface fracturing.When microwave-induced borehole fracturing occurs,it promotes the distribution of thermal cracks in rock,but inhibits the width of cracks.The results also prove the reliability of the test system.

A transceiver frequency conversion module based on 3D micropackaging technology

The idea of Ku-band transceiver frequency conversion module design based on 3D micropackaging technology is proposed. By using the double frequency conversion technology,the dual transceiver circuit from Ku-band to L-band is realized by combining with the local oscillator and the power control circuit to complete functions such as amplification, filtering and gain. In order to achieve the performance optimization and a high level of integration of the Ku-band monolithic microwave integrated circuits(MMIC) operating chip, the 3 D vertical interconnection micro-assembly technology is used. By stacking solder balls on the printed circuit board(PCB), the technology decreases the volume of the original transceiver to a miniaturized module. The module has a good electromagnetic compatibility through special structure designs. This module has the characteristics of miniaturization, low power consumption and high density, which is suitable for popularization in practical application.

Conducted EMI Suppression in Plasma Cutting Power Supply

A systematic approach to the design of the conducted electromagnetic interference （EMI） filter of high-density plasma cutting power supply has been developed. Converter components have been accurately modeled, with parasitic elements extracted to reveal their impacts on the EMI noises. Circuit simulations have been used to analyze and minimize the EMI noises. Conducted EMI noise measurement and filter design of this power supply have been achieved which successfully satisfy the FCC class B limits in the frequency range from 150 kHz to 30 MHz. The analyses and experimental results show that the designed filter guarantees that the required attenuation will be achieved.

Adaptive Maxwell’s Equations Derived Optimization and Its Application in Antenna Array Synthesis

In this paper,a self-adaptive method for the Maxwell’s Equations Derived Optimization(MEDO)is proposed.It is implemented by applying the Sequential Model-Based Optimization(SMBO)algorithm to the iterations of the MEDO,and achieves the automatic adjustment of the parameters.The proposed method is named as adaptive Maxwell’s equations derived optimization(AMEDO).In order to evaluate the performance of AMEDO,eight benchmarks are used and the results are compared with the original MEDO method.The results show that AMEDO can greatly reduce the workload of manual adjustment of parameters,and at the same time can keep the accuracy and stability.Moreover,the convergence of the optimization can be accelerated due to the dynamical adjustment of the parameters.In the end,the proposed AMEDO is applied to the side lobe level suppression and array failure correction of a linear antenna array,and shows great potential in antenna array synthesis.

EMC design for actuators in the FAST reflector

An active reflector is one of the three main innovations incorporated in the Five-hundredmeter Aperture Spherical radio Telescope（FAST）.The deformation of such a huge spherically shaped reflector into different transient parabolic shapes is achieved by using 2225 hydraulic actuators which change the position of the 2225 nodes through the connected down tied cables.For each different tracking process of the telescope,more than 1/3 of these 2225 actuators must be in operation to tune the parabolic aperture accurately and meet the surface error restriction.This means that some of these actuators are inevitably located within the main beam of the receiver,and Electromagnetic Interference（EMI）from the actuators must be mitigated to ensure the scientific output of the telescope.Based on the threshold level of interference detrimental to radio astronomy described in ITU-R Recommendation RA.769 and EMI measurements,the shielding efficiency（SE）requirement for each actuator is set to be 80 d B in the frequency range from 70 MHz to 3 GHz.Therefore,Electromagnetic Compatibility（EMC）was taken into account in the actuator design by measures such as power line filters,optical fibers,shielding enclosures and other structural measures.In 2015,all the actuators had been installed at the FAST site.Till now,no apparent EMI from the actuators has been detected by the receiver,which demonstrates the effectiveness of these EMC measures.

SUPPRESSING CONDUCTED EMI FROM A DC/DC HIGH POWER CONVERTER BASED ON MIXED-MODE FILTER

Conducted electromagnetic interference (EMI) from a 7.5kVA DC/DC high power converter is investigated to agree with EN class A. Here in some passive methods of suppressing conducted EM Noise, such as mixed-mode (MM) EMI filters, snubbing circuits and other means, are used. Based on measurement, the sources of noise are detected with the characteristics analyzed in detail. The MM EMI filters is valuable means with which low-frequency part and some of the high frequency part of conducted EM Noise can be efficiently reduced. How to lay out the MM filters on both sides of the converter is outlined in detail. In addition, multiple grounding and RDC snubbing circuits are employed to improve the performance in high frequency. The experimental results confirm the methods adopted.

EXTREMELY LOW FREQUENCY MAGNETIC FIELD SUSCEPTIBILITY OF VISUAL DISPLAY UNITS

Extremely low frequency (ELF) magnetic field susceptibility is an index of visual display unit (VDU) quality and performance. This paper provided field measured data on the susceptibility for a large variety of VDUs. A test rig was built to study the susceptibility of VDUs to magnetic fields at fundamental and third harmonic frequencies. It was found that the susceptibility level is largely dependent on refresh rate of the VDU and the orientation of the external ELF field. It was also found that the VDU susceptibility is significantly increased in the presence of harmonic frequency magnetic fields. About 30% of the tested samples have susceptibility levels higher than that stated in IEC 1000-4-8 standard.

Low Intensity Microwave Fields and Radiation and Their Interaction with the Human Body

Sources of low-intensity microwave signals formation,which affect the metabolism processes when they interact with human body,are considered in the article.It’s noticed that increasing intensity level of the technogenic signals in environment significantly exceeds natural electromagnetic fields and radiation(EMR).The peculiarities of the registration and measurement of low-intensity signals parameters of the microwave range are considered.The processes of the interaction of the microwave signals and human organism are analyzed.Formation mechanisms of the positive and negative microwave flows of the electromagnetic radiation are revealed.Particularly,possible formation mechanism of the microwave EMR fluxes of implants in the human body.The results of the experimental study of the EMR signals levels of the objects contacting with human body,partly materials for bone defects replacement and soft tissues regeneration so as materials for physiotherapy,are given.The use of the term“electromagnetic compatibility”for materials which contacting the human body,is proposed.The expediency of its use is proven.Microwave properties of materials for clothes,minerals and building materials,which can affect the human body and environment,have been also studied.

Dual-current-injection CSCC Active Common-mode EMI Filters with High Insertion Loss for DC-DC Converters

With the increase in the switching frequency and power density,DC-DC converters encounter more severe electromagnetic interference(EMI)problems.To suppress the common-mode EMI generated by converters,as well as maintain the high-power-density of converters,the active EMI filter(AEF)has attracted increasing interest owing to its small volume.The EMI suppression effect of the common single-stage single-sense single-injection AEF is confined because of the limited insertion loss,and the volume of the multi-stage AEF will be bulky.To solve this problem,this paper proposes a compact dual-current-injection current-sense current-compensation(DCJ-CSCC)AEF to increase the insertion loss in the entire conducted EMI frequency band,as well as considering the volume of the AEF.The structure and operating principle of the proposed AEF are introduced.Finally,taking a boost converter as an example,the effectiveness and advantages of the proposed DCJ-CSCC AEF were verified through a simulation and experiment,the results show that the proposed AEF has a better EMI suppression effect on the entire conducted EMI frequency band with a similar volume compared with existing single-injection feedforward current-sense current-compensation(FF-CSCC)and feedback current-sense current-compensation(FB-CSCC)AEFs.This paper provides a new selection for EMI suppression in DC-DC converters.