Photocarrier radiometry for noncontact evaluation of space monocrystalline silicon solar cell under low-energy electron irradiation

A space monocrystalline silicon（c-Si） solar cell under low-energy（〈 1 MeV） electron irradiation was investigated using noncontact photocarrier radiometry（PCR）. Monte Carlo simulation（MCS） was employed to characterize the effect of different energy electron irradiation on the c-Si solar cell. The carrier transport parameters（carrier lifetime, diffusion coefficient, and surface recombination velocities） were obtained by best fitting the experimental results with a theoretical one-dimensional two-layer PCR model. The results showed that the increase of the irradiation electron energy caused a large reduction of the carrier lifetime and diffusion length. Furthermore, the rear surface recombination velocity of the Si：p base of the solar cell at the irradiation electron energy of 1 Me V was dramatically enhanced due to 1 MeV electron passing through the whole cell. Short-circuit current（I sc） degradation evaluated by PCR was in good agreement with that obtained by electrical measurement.

Photoluminescence Analysis of Injection-Enhanced Annealing of Electron Irradiation-Induced Defects in GaAs Middle Cells for Triple-Junction Solar Cells

Photolumineseenee measurements are carried out to investigate the injection-enhanced annealing behavior of electron radiation-induced defects in a GaAs middle cell for GaInP/GaAs/Ge triple-junction solar cells which are irradiated by 1.8 MeV with a fluence of i ~ 1015 cm-2. Minority-carrier injection under forward bias is observed to enhance the defect annealing in the GaAs middle cell, and the removal rate of the defect is determined with photoluminescenee radiative efficiency recovery. Furthermore, the injection-enhanced defect removal rates obey a simple Arrhenius law. Therefore, the annealing activation energy is acquired and is equal to 0.58eV. Finally, in comparison of the annealing activation energies, the E5 defect is identified as a primary non-radiative recombination center.

TiO_(2)Electron Transport Layer with p-n Homojunctions for Efficient and Stable Perovskite Solar Cells

Low-temperature processed electron transport layer(ETL)of TiO_(2)that is widely used in planar perovskite solar cells(PSCs)has inherent low carrier mobility,resulting in insufficient photogenerated elec-tron transport and thus recombination loss at buried interface.Herein,we demonstrate an effective strategy of laser embedding of p-n homojunctions in the TiO_(2)ETL to accelerate electron transport in PSCs,through localized build-in electric fields that enables boosted electron mobility by two orders of magnitude.Such embedding is found significantly helpful for not only the enhanced crystallization quality of TiO_(2)ETL,but the fabrication of perovskite films with larger-grain and the less-trap-states.The embedded p-n homojunction enables also the modulation of interfacial energy level between perovskite layers and ETLs,favoring for the reduced voltage deficit of PSCs.Benefiting from these merits,the formamidinium lead iodide(FAPbI_(3))PSCs employing such ETLs deliver a champion efficiency of 25.50%,along with much-improved device stability under harsh conditions,i.e.,maintain over 95%of their initial efficiency after operation at maximum power point under continuous heat and illumination for 500 h,as well as mixed-cation PSCs with a champion efficiency of 22.02%and over 3000 h of ambient storage under humidity stability of 40%.Present study offers new possibilities of regulating charge transport layers via p-n homojunction embedding for high performance optoelectronics.

Mechanical properties of multi-scale germanium specimens from space solar cells under electron irradiation

During long-term service in space,Gallium Arsenide(GaAs)solar cells are directly exposed to electron irradiation which usually causes a dramatic decrease in their performance.In the multilayer structure of solar cells,the germanium(Ge)layer occupies the majority of the thickness as the substrate.Due to the intrinsic brittleness of semiconductor material,there exist various defects during the preparation and assembly of solar cells,the influences of which tend to be intensified by the irradiation effect.In this work,first,Ge specimens for mechanical tests were prepared at scales from microscopic to macroscopic.Then,after different doses of electron irradiation,the mechanical properties of the Ge specimens were investigated.The experimental results demonstrate that electron irradiation has an obvious effect on the mechanical property variation of Ge in diverse scales.The four-point bending test indicates that the elastic modulus,fracture strength,and maximum displacement of the Ge specimens all increase,and reach the maximum value at the irradiation dose of 1×10^(15)e/cm^(2).The micrometer scale cantilever and nanoindentation tests present similar trends for Ge specimens after irradiation.Atomic Force Microscope(AFM)also observed the change in surface roughness.Finally,a fitting model was established to characterize the relation between modulus change and electron irradiation dose.

Toward high-efficiency perovskite solar cells with one-dimensional oriented nanostructured electron transport materials

The unique advantages of one-dimensional(1D)oriented nanostructures in light-trapping and chargetransport make them competitive candidates in photovoltaic(PV)devices.Since the emergence of perovskite solar cells(PSCs),1D nanostructured electron transport materials(ETMs)have drawn tremendous interest.However,the power conversion efficiencies(PCEs)of these devices have always significantly lagged behind their mesoscopic and planar counterparts.High-efficiency PSCs with 1D ETMs showing efficiency over 22%were just realized in the most recent studies.It yet lacks a comprehensive review covering the development of 1D ETMs and their application in PSCs.We hence timely summarize the advances in 1D ETMs-based solar cells,emphasizing on the fundamental and optimization issues of charge separation and collection ability,and their influence on PV performance.After sketching the classification and requirements for high-efficiency 1D nanostructured solar cells,we highlight the applicability of 1D TiO_(2)nanostructures in PSCs,including nanotubes,nanorods,nanocones,and nanopyramids,and carefully analyze how the electrostatic field affects cell performance.Other kinds of oriented nanostructures,e.g.,ZnO and SnO_(2)ETMs,are also described.Finally,we discuss the challenges and propose some potential strategies to further boost device performance.This review provides a broad range of valuable work in this fast-developing field,which we hope will stimulate research enthusiasm to push PSCs to an unprecedented level.

Thermally Evaporated ZnSe for Efficient and Stable Regular/Inverted Perovskite Solar Cells by Enhanced Electron Extraction

Electron transport layers(ETLs)are crucial for achieving efficient and stable planar perovskite solar cells(PSCs).Reports on versatile inorganic ETLs using a simple film fabrication method and applicability for both low-cost planar regular and inverted PSCs with excellent efficiencies(>22%)and high stability are very limited.Herein,we employ a novel inorganic ZnSe as ETL for both regular and inverted PSCs to improve the efficiency and stability using a simple thermal evaporation method.The TiO_(2)-ZnSe-FAPbl_(3)heterojunction could be formed,resulting in an improved charge collection and a decreased carrier recombination further proved through theoretical calculations.The optimized regular PSCs based on TiO_(2)/ZnSe have achieved 23.25%efficiency with negligible hysteresis.In addition,the ZnSe ETL can also effectively replace the unstable bathocuproine(BCP)in inverted PSCs.Consequently,the ZnSe-based inverted device realizes a champion efficiency of 22.54%.Moreover,the regular device comprising the TiO_(2)/ZnSe layers retains 92%of its initial PCE after 10:00 h under 1 Sun continuous illumination and the inverted device comprising the C_(60)/ZnSe layers maintains over 85%of its initial PCE at 85℃for 10:00 h.This highlights one of the best results among universal ETLs in both regular and inverted perovskite photovoltaics.

Cross-linked polyelectrolyte reinforced SnO_(2)electron transport layer for robust flexible perovskite solar cells

SnO_(2)electron transport layer(ETL)is a vital component in perovskite solar cells(PSCs),due to its excellent photoelectric properties and facile fabrication process.In this study,we synthesized a water-soluble and adhesive polyelectrolyte with ethanolamine(EA)and poly-acrylic acid(PAA).The linear PAA was crosslinked by EA,forming a 3D network that stabilized the SnO_(2)nanoparticle dispersion.An organic–inorganic hybrid ETL is developed by introducing the cross-linked PAA-EA into SnO_(2)ETL,which prevents nano particle agglomeration and facilitates uniform SnO_(2)film formation with fewer defects.Additionally,the PAA-EA-modified SnO_(2)facilitated a uniform and compact perovskite film,enhancing the interface contact and carrier transport.Consequently,the PAA-EA-modified PSCs exhibited excellent PCE of 24.34%and 22.88%with high reproducibility for areas of 0.045 and 1.00 cm~2,respectively.Notably,owing to structure reinforce effect of PAA-EA in SnO_(2)ETL,flexible device demonstrated an impressive PCE of 23.34%while maintaining 90.1%of the initial PCE after 10,000 bending cycles with a bending radius of 5 mm.This successful approach of polyelectrolyte reinforced hybrid organic–inorganic ETL displays great potential for flexible,large-area PSCs application.

Alleviating Interfacial Recombination of Heterojunction Electron Transport Layer via Oxygen Vacancy Engineering for Efficient Perovskite Solar Cells Over 23%

Electron transport layer(ETL)is pivotal to charge carrier transport for PSCs to reach the Shockley-Queisser limit.This study provides a fundamental understanding of heterojunction electron transport layers(ETLs)at the atomic level for stable and efficient perovskite solar cells(PSCs).The bilayer structure of an ETL composed of SnO_(2) on TiO_(2) was examined,revealing a critical factor limiting its potential to obtain efficient performance.Alteration of oxygen vacancies in the TiO_(2) underlayer via an annealing process is found to induce manipulated band offsets at the interface between the TiO_(2) and SnO_(2) layers.In-depth electronic investigations of the bilayer structure elucidate the importance of the electronic properties at the interface between the TiO_(2) and SnO_(2) layers.The apparent correlation in hysteresis phenomena,including current density-voltage(J-V)curves,appears as a function of the type of band alignment.Density functional theory calculations reveal the intimate relationship between oxygen vacancies,deep trap states,and charge transport efficiency at the interface between the TiO_(2) and SnO_(2) layers.The formation of cascade band alignment via control over the TiO_(2) underlayer enhances device performance and suppresses hysteresis.Optimal performance exhibits a power conversion efficiency(PCE)of 23.45%with an open-circuit voltage(V_(oc))of 1.184 V,showing better device stability under maximum power point tracking compared with a staggered bilayer under one-sun continuous illumination.

Systematic Review on Critical Factors and Their Optimization for Solar Cell Performance Enhancement

Solar cells and other renewable energy sources are crucial in today's world where sustainability and environmental consciousness is at peak.Because of this,creating the optimal capacity is a fair aim for the operators of such technologies.The transformation of solar energy into either electricity by means of photovoltaics or into useable fuel by means of photo electrochemical cells remained a primary objective for research organizations and development sectors.In this piece,we will take a look back at the history of solar cells and examine their progression through the generations.The significant aspects which have an impact on the solar cells' performance are also discussed.This article provides a comprehensive and in-depth overview of the important aspects that affect the solar cells' performance,as well as a discussion of the application of bio-inspired optimization algorithms to improve the parameters of solar cells.Reviewing critical factors and their optimization for solar cell performance enhancement is crucial.It helps identify key performance factors,understand limitations,and challenges,and identify effective optimization strategies.By evaluating trade-offs and synergies,it guides future research and informs industrial applications,leading to more efficient and sustainable solar cell technologies.

Non-ionizing energy loss calculations for modeling electron-induced degradation of Cu(In,Ga)Se_2 thin-film solar cells

The lowest energies which make Cu,In,Ga,and Se atoms composing Cu（In,Ga）Se_2（CIGS） material displaced from their lattice sites are evaluated,respectively.The non-ionizing energy loss（NIEL） for electron in CIGS material is calculated analytically using the Mott differential cross section.The relation of the introduction rate（k） of the recombination centers to NIEL is modified,then the values of k at different electron energies are calculated.Degradation modeling of CIGS thin-film solar cells irradiated with various-energy electrons is performed according to the characterization of solar cells and the recombination centers.The validity of the modeling approach is verified by comparison with the experimental data.

Influence of dye molecular structure on electron transfer in 2,9,16,23-tetracarboxy zinc phthalocyanine sensitized solar cell

2, 9, 16, 23-tetracarboxy zinc phthalocyanine （ZnTCPc） is synthesized and characterized by physicochemical and theoretical methods and it is used as a photosensitizer in dye-sensitized solar cells （DSSC）. The excited lifetime, band gap and frontier orbital distribution of ZnTCPc are investigated by fluorescence spectra, cyclic voltammetry and quantum calculation. The results show that the excited lifetime and band gap are 0. 1 ns and 1.81 eV, respectively. Moreover, it is found that the highest occupied molecular orbital （HOMO） location is not shared by both the zinc metal and the isoindoline ligands, and the lowest unoccupied molecular orbital（LUMO） location does not strengthen the interaction coupling between ZnTCPc and TiO：. As a result, the ZnTCPc-DSSC gains a short-circuit current density of 0. 147 mA/cm2, an open-circuit photovoltage of 277 mV, a fill factor of 0. 51 and an overall conversion efficiency of 0. 021%.

Tin oxide(SnO_2) as effective electron selective layer material in hybrid organic–inorganic metal halide perovskite solar cells

The emergence of hybrid organic-inorganic metal halide perovskite solar cells （PSCs） causes a break through in the solar technology recently due to its fabrication processes. The dramatic enhancenlent in in 2009 to the recent certified record PCE of 22.7% superior optoelectronic properties and the low-cost power conversion efficiency （PCE） of PSCs flom 3.8% ndicates huge potential of PSCs for future high efficiency and large scale photovoltaic manufacturing. The electron selective layer （ESL） plays an important role in electron extraction and hole blocking function in PSCs, and there have been great interest in developing efficient ESL materials. Recently, tin oxide （SnO2） as an ESL has attracted significant research attentions owing to its low temperature preparation processes as well as yielding high PCE and good stability of PSCs. In this perspective article, we focus on the development progress of SnO2 as an ESL m PSCs, and discuss the strategies for preparing SnO2 to achieve PSCs with high efficiency, less hysteresis and good device stability.

Highly efficient flexible perovskite solar cells with vacuum-assisted low-temperature annealed SnO2 electron transport layer

The demand for lightweight, flexible, and high-performance portable power sources urgently requires high-efficiency and stable flexible solar cells. In the case of perovskite solar cells(PSCs), most of the common electron transport layer(ETL) needs to be annealed for improving the optoelectronic properties,while conventional flexible substrates could barely stand the high temperature. Herein, a vacuumassisted annealing SnO_(2) ETL at low temperature(100℃) is utilized in flexible PSCs and achieved high efficiency of 20.14%. Meanwhile, the open-circuit voltage(V_(oc)) increases from 1.07 V to 1.14 V. The flexible PSCs also show robust bending stability with 86.8% of the initial efficiency is retained after 1000 bending cycles at a bending radius of 5 mm. X-ray photoelectron spectroscopy(XPS), atomic force microscopy(AFM), and contact angle measurements show that the density of oxygen vacancies, the surface roughness of the SnO_(2) layer, and film hydrophobicity are significantly increased, respectively. These improvements could be due to the oxygen-deficient environment in a vacuum chamber, and the rapid evaporation of solvents. The proposed vacuum-assisted low-temperature annealing method not only improves the efficiency of flexible PSCs but is also compatible and promising in the large-scale commercialization of flexible PSCs.

Non-fullerene small molecule electron acceptors for high-performance organic solar cells

Fullerenes and their derivatives are important types of electron acceptor materials and play a vital role in organic solar cell devices. However, the fullerene acceptor material has some difficulties to overcome the intrinsic shortcomings, such as weak absorption in the visible range, difficulty in modification and high cost, which limit the performance of the device and the large-scale application of this type of acceptors. In recent years, non-fullerene electron acceptor material has attracted the attention of scientists due to the advantages of adjustable energy level, wide absorption, simple synthesis, low processing cost and good solubility. Researchers can use the rich chemical means to design and synthesize organic small molecules and their oligomers with specific aggregation morphology and excellent optoelectronic prop- erties. Great advances in the field of synthesis, device engineering, and device physics of non-fullerene acceptors have been achieved in the last few years. At present, non-fullerene small molecules based photovoltaic devices achieve the highest efficiency more than 13% and the efficiency gap between fullerenetype and non-fullerene-type photovoltaic devices is gradually narrowing. In this review, we explore recent progress of non-fullerene small molecule electron acceptors that have been developed and led to highefficiency photovoltaic devices and put forward the prospect of development in the future.

Composite electron transport layer for efficient N-I-P type monolithic perovskite/silicon tandem solar cells with high open-circuit voltage

Perovskite/silicon tandem solar cells(PSTSCs) have exhibited huge technological potential for breaking the Shockley-Queisser limit of single-junction solar cells. The efficiency of P-I-N type PSTSCs has surpassed the single-junction limit, while the performance of N-I-P type PSTSCs is far below the theoretical value. Here, we developed a composite electron transport layer for N-I-P type monolithic PSTSCs with enhanced open-circuit voltage(VOC) and power conversion efficiency(PCE). Lithium chloride(Li Cl) was added into the tin oxide(SnO_(2)) precursor solution, which simultaneously passivated the defects and increased the electron injection driving force at the electron transfer layer(ETL)/perovskite interface.Eventually, we achieved monolithic PSTSCs with an efficiency of 25.42% and V_(OC) of 1.92 V, which is the highest PCE and VOCin N-I-P type perovskite/Si tandem devices. This work on interface engineering for improving the PCE of monolithic PSTSCs may bring a new hot point about perovskite-based tandem devices.

Effects of 50keV and 100keV Proton Irradiation on GaInP/GaAs/Ge Triple-Junction Solar Cells

GaInP/GaAs/Ge triple-junction solar cells were irradiated with 50 keV and 100 keV protons at fluences of 5 × 10^10 cm^-2, 1 × 10^11 cm^-2,1 × 10^12 cm^-2, and 1 × 10^13 cm^-2. Their performance degradation is analyzed using current-voltage characteristics and spectral response measurements, and then the changes in Isc, Voc, Pmax and the spectral response of the cells are observed as functions of proton irradiation fluence and energy. The results show that the spectral response of the top cell degrades more significantly than that of the middle cell, and 100 keV proton-induced degradation rates of Isc, Voc and Pmax are larger compared with 50 keV proton irradiation.

Spatial configuration engineering of perylenediimide-based non-fullerene electron transport materials for efficient inverted perovskite solar cells

Due to their excellent photoelectron chemical properties and suitable energy level alignment with perovskite,perylene diimide(PDI)derivatives are competitive non-fullerene electron transport material(ETM)candidates for perovskite solar cells(PSCs).However,the conjugated rigid plane structure of PDI units result in PDI-based ETMs tending to form large aggregates,limiting their application and photovoltaic performance.In this study,to restrict aggregation and further enhance the photovoltaic performance of PDI-type ETMs,two PDI-based ETMs,termed PDO-PDI2(dimer)and PDO-PDI3(trimer),were constructed by introducing a phenothiazine 5,5-dioxide(PDO)core building block.The research manifests that the optoelectronic properties and film formation property of PDO-PDI2 and PDO-PDI3 were deeply affected by the molecular spatial configuration.Applied in PSCs,PDO-PDI3 with threedimensional spiral molecular structure,exhibits superior electron extraction and transport properties,further achieving the best PCE of 18.72%and maintaining 93%of its initial efficiency after a 720-h aging test under ambient conditions.

Non-conjugated polymers as thickness-insensitive electron transport materials in high-performance inverted organic solar cells

Two non-conjugated polymers PEIE-DBO and PEIE-DCO, prepared by quaternization of polyethyleneimine ethoxylate by 1,8-dibromooctane and 1,8-dichlorooctane respectively, are developed as electron transport layer(ETL) in high-performance inverted organic solar cells(OSCs), and the effects of halide ions on polymeric photoelectric performance are fully investigated. PEIE-DBO possesses higher electron mobility(3.68×10-4 cm2 V-1s-1), higher conductivity and more efficient exciton dissociation and electron extraction, attributed to its lower work function(3.94 eV) than that of PEIE-DCO, which results in better photovoltaic performance in OSCs. The inverted OSCs with PTB7-Th: PC71BM as photoactive layer and PEIE-DBO as ETL exhibit higher PCE of 10.52%, 9.45% and 9.09% at the thickness of 9, 35 and 50 nm,respectively. To our knowledge, PEIE-DBO possesses the best thickness-insensitive performance in polymeric ETLs of inverted fullerene-based OSCs. Furthermore, PEIE-DBO was used to fabricate the inverted non-fullerene OSCs(PM6:Y6) and obtained a high PCE of 15.74%, which indicates that PEIE-DBO is effective both in fullerene-based OSCs and fullerene-free OSCs.

Molecular design towards two-dimensional electron acceptors for efficient non-fullerene solar cells

Non-fullerene polymer solar cells(NF-PSCs) have gained wide attention recently. Molecular design of non-fullerene electron acceptors effectively promotes the photovoltaic performance of NF-PSCs. However,molecular electron acceptors with 2-dimensional(2 D) configuration and conjugation are seldom reported.Herein, we designed and synthesized a series of novel 2 D electron acceptors for efficient NF-PSCs. With rational optimization on the conjugated moieties in both vertical and horizontal direction, these 2 D electron acceptors showed appealing properties, such as good planarity, full-spectrum absorption, high absorption extinction coefficient, and proper blend morphology with donor polymer. A high PCE of 9.76%was achieved for photovoltaic devices with PBDB-T as the donor and these 2 D electron acceptors. It was also found the charge transfer between the conjugated moieties in two directions of these 2 D molecules contributes to the utilization of absorbed photos, resulting in an exceptional EQE of 87% at 730 nm. This work presents rational design guidelines of 2 D electron acceptors, which showed great promise to achieve high-performance non-fullerene polymer solar cells.

Inverted organic solar cells with solvothermal synthesized vanadium-doped TiO2 thin films as efficient electron transport layer

We investigated the effects of using different thicknesses of pure and vanadium-doped thin films of TiO2 as the electron transport layer in the inverted configuration of organic photovoltaic cells based on poly（3-hexylthiophene） P3HT：[6-6] phenyl-（6） butyric acid methyl ester（PCBM）. 1% vanadium-doped TiO2nanoparticles were synthesized via the solvothermal method. Crystalline structure, morphology, and optical properties of pure and vanadium-doped TiO2 thin films were studied by different techniques such as x-ray diffraction, scanning electron microscopy, transmittance electron microscopy, and UV–visible transmission spectrum. The doctor blade method which is compatible with roll-2-roll printing was used for deposition of pure and vanadium-doped TiO2 thin films with thicknesses of 30 nm and 60 nm. The final results revealed that the best thickness of TiO2 thin films for our fabricated cells was 30 nm. The cell with vanadium-doped TiO2 thin film showed slightly higher power conversion efficiency and great Jsc of 10.7 mA/cm^2 compared with its pure counterpart. In the cells using 60 nm pure and vanadium-doped TiO2 layers, the cell using the doped layer showed much higher efficiency. It is remarkable that the external quantum efficiency of vanadium-doped TiO2 thin film was better in all wavelengths.