Palladium-catalyzed highly regioselective Heck reaction of aryl nonaflates with electron-rich olefins

Highly efficient palladium-catalyzed Heck coupling of aryl nonaflates with electron-rich vinyl ethers, and enamides is described. These reactions afforded exclusively the branched products in good yields. The results indicated that aryl nonaflates are effective alternative to the frequently employed aryl triflates.

Modeling and analysis of air combustion and steam regeneration in methanol to olefins processes

Light olefins is the incredibly important materials in chemical industry.Methanol to olefins(MTO),which provides a non-oil route for light olefins production,received considerable attention in the past decades.However,the catalyst deactivation is an inevitable feature in MTO processes,and regeneration,therefore,is one of the key steps in industrial MTO processes.Traditionally the MTO catalyst is regenerated by removing the deposited coke via air combustion,which unavoidably transforms coke into carbon dioxide and reduces the carbon utilization efficiency.Recent study shows that the coke species over MTO catalyst can be regenerated via steam,which can promote the light olefins yield as the deactivated coke species can be essentially transferred to industrially useful synthesis gas,is a promising pathway for further MTO processes development.In this work,we modelled and analyzed these two MTO regeneration methods in terms of carbon utilization efficiency and technology economics.As shown,the steam regeneration could achieve a carbon utilization efficiency of 84.31%,compared to 74.74%for air combustion regeneration.The MTO processes using steam regeneration can essentially achieve the near-zero carbon emission.In addition,light olefins production of the MTO processes using steam regeneration is 12.81%higher than that using air combustion regeneration.In this regard,steam regeneration could be considered as a potential yet promising regeneration method for further MTO processes,showing not only great environmental benefits but also competitive economic performance.

Effects of zinc on Fe-based catalysts during the synthesis of light olefins from the Fischer-Tropsch process

Fe‐based catalysts for the production of light olefins via the Fischer‐Tropsch synthesis were modi‐fied by adding a Zn promoter using both microwave‐hydrothermal and impregnation methods. The physicochemical properties of the resulting catalysts were determined by scanning electron mi‐croscopy, the Brunauer‐Emmett‐Teller method, X‐ray diffraction, H2 temperature‐programed re‐duction and X‐ray photoelectron spectroscopy. The results demonstrate that the addition of a Zn promoter improves both the light olefin selectivity over the catalyst and the catalyst stability. The catalysts prepared via the impregnation method, which contain greater quantities of surface ZnO, exhibit severe carbon deposition following activity trials. In contrast, those materials synthesized using the microwave‐hydrothermal approach show improved dispersion of Zn and Fe phases and decreased carbon deposition, and so exhibit better CO conversion and stability.

Production of Light Olefins from Biosyngas by Two-stage Catalytic Conversion Process via Dimethyl Ether

NiSAPO-34 and NiSAPO-34/HZSM-5 were prepared and evaluated for the performance of dimethyl ether （DME） conversion to light olefins （DTO）. The processes of two-stage light olefin production, DME synthesis and the following DTO, were also investigated using biosyngas as feed gas over Cu/Zn/A1/HZSM-5 and the optimized 2%NiSAPO-34/HZSM- 5. The results indicated that adding 2%Ni to SAPO-34 did not change its topology structure, but resulted in the forming of the moderately strong acidity with decreasing acid amounts, which slightly enhanced DME conversion activity and C2=-C3= selectiw ity. Mechanically mixing 2%NiSAPO-34 with HZSM-5 at the weight ratio of 3.0 further prolonged DME conversion activity to be more than 3 h, which was due to the stable acid sites from HZSM-5. The highest selectivity to light olefins of 90.8% was achieved at 2 h time on stream. The application of the optimized 2%NiSAPO-34/HZSM-5 in the second-stage reactor for DTO reaction showed that the catalytic activity was steady for more than 5 h and light olefin yield was as high as 84.6 g/m3syngas when the biosyngas （H2/CO/CO2/N2/CH4=41.5/26.9/14.2/14.6/2.89, vol%） with low H/C ratio of 1.0 was used as feed gas.

催化裂化装置多产丙烯助剂Olefins Max的应用试验

对多产丙烯的助剂OlefinsMax进行了小型和中型试验评价 ,并对该助剂在镇海炼油化工股份有限公司3 .0 0Mt/a催化裂化装置的工业应用试验作了总结 ,结果表明通过在主催化剂中配合使用多产丙烯助剂 ,能明显增加丙烯收率 ,在装置生产负荷为 80 %时主催化剂中添加 3 %～ 4%的OlefinsMax助剂 ,使装置每天多生产丙烯 5 0t以上 ,且对汽油质量无不利影响 。

Production of Low-carbon Light Olefins from Catalytic Cracking of Crude Bio-oil

Low-carbon light olefins are the basic feedstocks for the petrochemical industry. Catalytic cracking of crude bio-oil and its model compounds （including methanol, ethanol, acetic acid, acetone, and phenol） to light olefins were performed by using the La/HZSM-5 catalyst. The highest olefins yield from crude bio-oil reached 0.19 kg/（kg crude bio-oil）. The reaction conditions including temperature, weight hourly space velocity, and addition of La into the HZSM-5 zeolite can be used to control both olefins yield and selectivity. Moderate adjusting the acidity with a suitable ratio between the strong acid and weak acid sites through adding La to the zeolite effectively enhanced the olefins selectivity and improved the catalyst stability. The production of light olefins from crude bio-oil is closely associated with the chemical composition and hydrogen to carbon effective ratios of feedstock. The comparison between the catalytic cracking and pyrolysis of bio-oil was studied. The mechanism of the bio-oil conversion to light olefins was also discussed.

Preparation of modified Ce-SAPO-34 catalysts and their catalytic performances of methanol to olefins

The modified Ce-SAPO-34 catalysts were prepared with three methods, i.e., the liquid ion exchange with air calcination, impregnation with air calcination and impregnation with steam calcination methods. The catalytic performances of the catalysts for methanol to olefins were investigated. The properties of the catalysts were characterized using XRD, BET, XRF, FT-IR and NH3-TPD. The results indicated that compared to the SAPO-34 catalyst the catalyst prepared with the impregnation and air calcination prolonged the lifetime by 40 min and improved the selectivity to ethylene by 5% （mol） and the catalyst prepared with the impregnation and steam calcination showed the best modification effect, prolonging the lifetime by 70 min and improving the ethylene selectivity by 10% （mol）. The catalyst prepared with the liquid ion exchange showed similar behaviour as the SAPO-34 catalyst. It was verified that the porous structure and surface acidity of these catalysts determined their catalytic behaviors.

Iron-based Fischer–Tropsch synthesis of lower olefins: The nature of χ-Fe_5C_2 catalyst and why and how to introduce promoters

As a sustainable and short-flow process, iron-catalyzed direct conversion of CO-rich syngas to lower olefins without intermediate steps, i.e., Fischer–Tropsch-to-Olefins (FTO), has received increasing attention. However, its fundamental understanding is usually limited by the complex crystal phase composition in addition to the interferences of the promoter effects and inevitable catalyst deactivation. Until recently, the combination of multiple in-situ/ex-situ characterizations and theoretical studies has evidenced Hägg iron carbide (χ-Fe5C2) as the dominant active phase of iron-based Fischer–Tropsch catalysts. This perspective attempts to review and discuss some recent progresses on the nature of χ-Fe5C2catalyst and the crucial effects of promoters on the FTO performance from theoretical and experimental viewpoints, aiming to provide new insights into the rational design of iron-based FTO catalysts. © 2016 Science Press

Study on the deactivation and regeneration of the ZSM-5 catalyst used in methanol to olefins

ZSM-5 zeolite catalyst modified by a trace of metal cations shows high activity and high selectivity for the reaction of methanol to olefins （MTO）, but it inclines to deactivate during the reaction. In this paper, the mechanism of the catalyst deactivation and the regeneration method were studied by X-ray diffraction （XRD）, N2 adsorption-desorption, infrared spectra （IR）, and infrared spectra coupled with NH3 molecular probes （IR-NH3）. These characterizations indicated that coke formation was the main reason for the catalyst deactivation. To regenerate the deactivated catalyst, two methods, i.e., calcination and methanol leaching, were used. N2 adsorption-desorption, IR and IR-NH3 characteriza-tions showed that both methods can eliminate coke deposited on the catalyst and make the catalyst reactivated. XRD showed that the structure of the catalyst did not change after regeneration. Interestingly, the regenerated catalyst even showed better catalytic performance of the MTO reaction than the fresh one. Besides, the calcination regeneration can eliminate coke more completely, however, the methanol leaching method can be more easily carried out in situ in the reactor.

Review of Directly Producing Light Olefins via CO Hydrogenation

Directly making light olefins via CO hydrogenation is a promising process toobtain a non-petroleum based supply of alkenes. Limited by the ASF distribution function ofFischer-Tropsch synthesis, the yield of light olefins (C_2-C_4) can not reach the desired levels,which is a great challenge to overcome. Beginning with a brief introduction of F-T synthesis, thispaper provides a review of current research, including thermodynamic analysis, the ASF distributionfunction, the reaction performance of CO hydrogenation and slurry reactor studies. The problemscurrently faced by this research area are presented at the end of the article.

TiO_2 supported cobalt-manganese nano catalysts for light olefins production from syngas

Cobalt-manganese nano catalysts were prepared by sol-gel method. This research investigated the effects of different cobalt-manganese （Co/Mn = 1/1） loading, pH and calcination conditions on the catalytic performance of Co-Mn/TiO2 catalysts for Fischer-Tropsch synthesis （FTS） in a fixed bed reactor. It was found that the catalyst containing 30wt%（Co-Mn）/TiO2 was an optimal catalyst for the conversion of synthesis gas to light olefins especially propylene. The activity and selectivity of optimal catalyst were studied under different operational conditions. The results showed that the best operational conditions were H2/CO = 1/1 molar feed ratio at 250 ℃ and GHSV = 1300 h-1 un- der atmospheric pressure. Characterization of catalysts was carried out by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, N2 adsorption-desorlation measurements.

Systematic variation of the sodium/sulfur promoter content on carbon-supported iron catalysts for the Fischer–Tropsch to olefins reaction

The Fischer–Tropsch to olefins（FTO） process is a method for the direct conversion of synthesis gas to lower C–Colefins. Carbon-supported iron carbide nanoparticles are attractive catalysts for this reaction.The catalytic activity can be improved and undesired formation of alkanes can be suppressed by the addition of sodium and sulfur as promoters but the influence of their content and ratio remains poorly understood and the promoted catalysts often suffer from rapid deactivation due to particle growth. A series of carbon black-supported iron catalysts with similar iron content and nominal sodium/sulfur loadings of 1–30/0.5–5 wt% with respect to iron are prepared and characterized under FTO conditions at 1and 10 bar syngas pressure to illuminate the influence of the promoter level on the catalytic properties.Iron particles and promoters undergo significant reorganization during FTO operation under industrially relevant conditions. Low sodium content（1–3 wt%） leads to a delay in iron carbide formation. Sodium contents of 15–30 wt% lead to rapid loss of catalytic activity due to the covering of the iron surface with promoters during particle growth under FTO operation. Higher activity and slower loss of activity are observed at low promoter contents（1–3 wt% sodium and 0.5–1 wt% sulfur） but a minimum amount of alkali is required to effectively suppress methane and C–Cparaffin formation. A reference catalyst support（carbide-derived carbon aerogel） shows that the optimum promoter level depends on iron particle size and support pore structure.

Fe-modified HZSM-5 catalysts for ethanol conversion into light olefins

A series of Fe/HZSM-5 catalysts with different iron loadings were prepared by impregnation method.Characterization was performed by N2 adsorption-desorption,X-ray diffraction（XRD）,NH3 temperature-programmed desorption（NH3-TPD）,temperature-programmed reduction （TPR）,temperature-programmed oxidation（TPO）and thermogravimetry（TG）analysis.Iron content in the synthesized samples varied from 1.1 wt%to 20 wt%.The obtained samples have been used for ethanol conversion into light olefins.It was found that the amount of strong acidity at 300 -5 50-C on Fe-modified samples was decreased,going with another new acid site appearance at 550- 600-C and that Fe/HZSM-5 catalysts were highly selective towards light olefins,especially the 9FZ sample.In addition,Fe-modified catalysts suppressed the conversion of ethanol to aromatics and paraffins and enhanced their anti-carbon deposit ability.

Catalytic Transformation of Bio-oil to Olefins with Molecular Sieve Catalysts

Catalytic conversion of bio-oil into light olefins was performed by a series of molecular sieve catalysts, including HZSM-5, MCM-41, SAPO-34 and Y-zeolite. Based on the light olefins yield and its carbon selectivity, the production of light olefins decreased in the following order： HZSM-5〉SAPO-34〉MCM-41〉Y-zeolite. The highest olefins yield from bio-oil using HZSM- 5 catalyst reached 0.22 kg/kgbio-oil with carbon selectivity of 50.7% and a nearly complete bio-oil conversion. The reaction conditions and catalyst characterization were investigated in detail to reveal the relationship between the catalyst structure and the production of olefins. The comparison between the pyrolysis and catalytic pyrolysis of bio-oil was also performed.

ZSM-5/MAPO Composite Catalyst for Converting Methanol to Olefins in a Two-Stage Unit with a Dimethyl Ether Pre-Reactor

A ZSM-5/MAPO composite catalyst was prepared by adding ZSM-5 zeolite powder to a conventional molecular sieve synthesis system, followed by modification with NH_4H_2PO_4. The samples were characterized by XRD, SEM, IR, NH_3-TPD, and BET analyses. The catalytic property of the samples toward the methanol-to-olefin(MTO) reaction was evaluated in a connected in series two-stage unit equipped with a continuous flow(once-through) fixed-bed tubular reactor similar to an industrial reactor. The first reactor mainly converted methanol into dimethyl ether and water, followed by being subject to continuous reaction in the second reactor, in which DME was converted to hydrocarbons. The composites exhibited the typical framework topology of MFI, AEI and AFI, which represented the ZSM-5 zeolite, the molecular sieves AlPO-18 or SAPO-18, AlPO-5 or SAPO-5, respectively. The composites showed several advantages for optimizing the zeolite acidity, enhancing the mass transfer, and restraining the side reactions. Catalytic reaction results showed that the composites exhibited higher selectivity to light olefins(84.0%) and lower selectivity to C_2―C_4 alkanes and C_5^+ hydrocarbons than pure ZSM-5. Moreover, the composite zeolite loaded with 3% of P demonstrated improved catalytic activity and stability for the conversion of methanol to propylene, because the coking rate was obviously suppressed.

Effect of the support on cobalt carbide catalysts for sustainable production of olefins from syngas

Co2C‐based catalysts with SiO2,γ‐Al2O3,and carbon nanotubes(CNTs)as support materials were prepared and evaluated for the Fischer‐Tropsch to olefin(FTO)reaction.The combination of catalytic performance and structure characterization indicates that the cobalt‐support interaction has a great influence on the Co2C morphology and catalytic performance.The CNT support facilitates the formation of a CoMn composite oxide during calcination,and Co2C nanoprisms were observed in the spent catalysts,resulting in a product distribution that greatly deviates from the classical Anderson‐Schulz‐Flory(ASF)distribution,where only 2.4 C%methane was generated.The Co3O4 phase for SiO2‐andγ‐Al2O3‐supported catalysts was observed in the calcined sample.After reduction,CoO,MnO,and low‐valence CoMn composite oxide were generated in theγ‐Al2O3‐supported sample,and both Co2C nanospheres and nanoprisms were identified in the corresponding spent catalyst.However,only separated phases of CoO and MnO were found in the reduced sample supported by SiO2,and Co2C nanospheres were detected in the spent catalyst without the evidence of any Co2C nanoprisms.The Co2C nanospheres led to a relatively high methane selectivity of 5.8 C%and 12.0 C%of theγ‐Al2O3‐and SiO2‐supported catalysts,respectively.These results suggest that a relatively weak cobalt‐support interaction is necessary for the formation of the CoMn composite oxide during calcination,which benefits the formation of Co2C nanoprisms with promising catalytic performance for the sustainable production of olefins via syngas.

Catalytic Cracking of Cycloparaffins Admixed with Olefins:1. Single-Event Microkinetic(SEMK) Modeling

Single-event microkinetic(SEMK) model of the catalytic cracking of methylcyclohexane admixed with 1-octene over REUSY zeolites at 693 K—753 K in the absence of coke formation is enhanced. To keep consistency with the wellknown carbenium ion chemistry, hydride transfer forming and consuming allylic carbenium ions in the aromatization of cycloparaffins are further investigated and differentiated. The reversibility of endocyclic β-scission and cyclization reactions is refined by accounting explicitly for the reacting olefins and resulting cycloparaffins in the corresponding thermodynamics. 24 activation energies for the reactions involved in the cracking of cycloparaffins are obtained by the regression of 15 sets of experimental data upon taking the resulting 37 main cracking products, i. e., responses into account. The enhanced SEMK model can adequately describe the catalytic behavior of 37 main products with conversion and temperature.

Phosphite Ligand Modified Supported Rhodium Catalyst for Hydroformylation of Internal Olefins to Linear Aldehydes

A phosphite ligand modified heterogeneous catalyst was developed for the hydroformylation of internal olefins to linear aldehydes, which showed a high activity and high regioselectivity and could be separated easily by filtration after reaction in an autoclave. Three nanoporous silica sieves were used to investigate the influence of pore structure and shape selective performance of support on the regioselectivity to the linear products.

In situ Synthesis of SAPO-34 Zeolites in Kaolin Microspheres for a Fluidized Methanol or Dimethyl Ether to Olefins Process

SAPO-34 zeolite is considered to be an effective catalyst for methanol or dimethyl ether conversion to olefins. In this study,we developed the in situ synthesis technology to prepare SAPO-34 zeolite in kaolin micro-spheres as a catalyst for fluidized methanol or dimethyl ether to olefins process. The silicoaluminophosphate zeolite was first time reported to be synthesized in kaolin microspheres. The SAPO-34 content of synthesized catalyst was about 22% as measured by three different quantitative methods(micropore area,X-ray fluorescence and energy dispersive spectroscopy element analysis) . Most of the SAPO-34 zeolites were in nanoscale size and distributed uniformly inside the spheres. The catalytic performance was evaluated in fixed bed and fluidized bed reactors. Compared with the conventional spray-dry catalyst,SAPO/kaolin catalyst showed superior catalytic activities,bet-ter olefin selectivities(up to 94%,exclusive coke) ,and very good hydrothermal stability. The in situ synthesis of SAPO-34 in kaolin microspheres is a facile and economically feasible way to prepare more effective catalyst for fluidized MTO/DTO(methanol to olefins/dimethyl ether to olefins) process.

Effect of In_(2)O_(3)particle size on CO_(2) hydrogenation to lower olefins over bifunctional catalysts

A reaction-coupling strategy is often employed for CO_(2)hydrogenation to produce fuels and chemicals using oxide/zeolite bifunctional catalysts.Because the oxide components are responsible for CO_(2)activation,understanding the structural effects of these oxides is crucial,however,these effects still remain unclear.In this study,we combined In_(2)O_(3),with varying particle sizes,and SAPO‐34 as bifunctional catalysts for CO_(2)hydrogenation.The CO_(2)conversion and selectivity of the lower olefins increased as the average In_(2)O_(3)crystallite size decreased from 29 to 19 nm;this trend mainly due to the increasing number of oxygen vacancies responsible for CO_(2) and H_(2) activation.However,In_(2)O_(3)particles smaller than 19 nm are more prone to sintering than those with other sizes.The results suggest that 19 nm is the optimal size of In_(2)O_(3)for CO_(2)hydrogenation to lower olefins and that the oxide particle size is crucial for designing catalysts with high activity,high selectivity,and high stability.