Failure mechanism of a large-scale composite deposits caused by the water level increases

The failure of slope caused by variations in water levels on both banks of reservoirs is common.Reservoir landslides greatly threaten the safety of reservoir area.Taking large-scale composite deposits located on the Lancang River in Southwest China as a study case,the origin of the deposits was analyzed based on the field investigation and a multi-material model was established in the physical model test.Combined with numerical simulation,the failure mechanism of the composite deposits during reservoir water level variations was studied.The results indicate that the deformation of the large-scale composite deposits is a staged sliding mode during the impoundment process.The first slip deformation is greatly affected by the buoyancy weight-reducing effect,and the permeability of soil and variation in the water level are the factors controlling slope deformation initiation.The high water sensitivity and low permeability of fine grained soil play an important role in the re-deformation of deposits slope.During the impoundment process,the deformation trend of the deposit slope is decreasing,and vertical consolidation of soil and increasing hydrostatic pressure on the slope surface are the main reasons for deformation attenuation.It is considered that the probability of large-scale sliding of the deposits during the impoundment period is low.But the damage caused by local bank collapse of the deposit slope still needs attention.The results of this paper will further improve our understanding of the failure mechanism of composite deposits caused by water level increases and provide guidance for the construction of hydropower stations.

Electrodeposition of Ni-W Amorphous Alloy and Ni-W-SiC Composite Deposits

Ni-W alloys and their composite deposits are electroplated on the metals when an appropriate complex agent is selected on the base of the theories of electrochemistry and complex chemistry, and the principle of induced codeposition. Effects of the bath composition, pH value, temperature and current density on the electrode position of Ni-W alloys and their composite deposits have been investigated, and the effect of heat treatment temperature on the hardness, structure and cohesive force of the amorphous Ni-W alloys and their composite deposits are also discussed. Results showed that the alloys containing more than 44 wt pct W content and the composite deposits containing 7.8 wt pct SiC content could be obtained by making use of the appropriate bath composition and plating conditions. Alloys and their composite deposits with over 44 wt pct W content show amorphous structure. The hardness of amorphous Ni-W alloys and their composite deposits increases obviously when heated, and can reach to 1350 HV and 1520 HV respectively for 46 wt pct W content. The cohesion on Cu, carbon steel and stainless steel is very good.

Influence of additives and concentration of WC nanoparticles on properties of WC−Cu composite prepared by electroplating

The effects of additives(polyethylene glycol(PEG),sodium dodecyl sulfate(SDS))and WC nano-powder on the microstructure,relative density,hardness and electrical conductivity of electroplated WC−Cu composite were investigated.The preparation mechanism was also studied.The microstructure of samples was analyzed by XRD,SEM,EDS,TEM and HRTEM.The synergistic effect of PEG and SDS made the WC−Cu composite more compact during the electroplating process.The hardness of WC−Cu composites increased with the increase in WC content,while the electrical conductivity decreased with the increase in WC content.The density of samples tended to increase initially and then decreased with increase in the additive content.When the electroplating solution contained 10 g/L WC nanopowder,0.2 g/L PEG and 0.1 g/L SDS,the WC−Cu composite exhibited hardness of HV 221 and electric conductivity of 53.7 MS/m.Therefore,the results suggest that WC−Cu composite with excellent properties can be obtained by optimizing the content of additives and WC particles.

Electrochemical oxidation of polyethylene glycol in electroplating solution using paraffin composite copper hexacyanoferrate modified (PCCHM) anode

Electrochemical oxidation of polyethylene glycol(PEG) in an acidic(pH 0.18 to 0.42) and high ionic strength electroplating solution was investigated. The electroplating solution is a major source of wastewater in the printing wiring board industry. A paraffin composite copper hexacyanoferrate modified(PCCHM) electrode was used as the anode and a bare graphite electrode was used as the cathode. The changes in PEG and total organic carbon(TOC) concentrations during the course of the reaction were monitored. The efficiency of the PCCHM anode was compared with bare graphite anode and it was found that the former showed significant electrocatalytic property for PEG and TOC removal. Chlorides present in the solution were found to contribute significantly in the overall organic removal process. Short chain organic compounds like acetic acid, oxalic acid, formic acid and ethylene glycol formed during electrolysis were identified by HPLC method. Anode surface area and applied current density were found to influence the electro-oxidation process, in which the former was found to be dominating. Investigations of the kinetics for the present electrochemical reaction suggested that the two stage first-order kinetic model provides a much better representation of the overall mechanism of the process if compared to the generalized kinetic model.

Preparation of carbon nanotube composite material with metal matrix by electroplating

It is demonstrated that the nickel can be deposited directly on the surface of carbon nanotubes without pre-sensitization by Sn 2+ and Pd 2+ in a watt bath containing suspended nanotubes by electroplating. The nickel is deposited as spherical nanoparticle on the nanotubes. By increasing reaction time, the carbon nanotube is fully coated with nickel. A probable model, which represents the formation process of carbon nanotube-nickel composites by electroplating, is presented. The results show that this method is efficient and simple for preparing carbon nanotube-metal composite.

Effect of pH on Mechanical, Physical and Tribological Properties of Electroless Ni-P-Al2〇 3 Composite Deposits for Marine Applications

： Successful co-deposition of fine particulate matter within an Electroless Nickel-Phosphorous （ENi-P） matrix is dependent on various factors like bath composition, particle compatibility with metallic matrix, bath reactivity （pH）, particle size and their distribution. ENi-P deposits incorporating Al2O3/ Alumina in a disperse phase have varied effects on properties and attributes like surface roughness （Ra／ microhardness, wear resistance, corrosion resistance and surface morphology of the deposits obtained. This paper experimentally investigates the effect of alumina （1.55 g/L） on Ra, microhardness, surface morphology, deposition rate, wettability, wear resistance and corrosion resistance of ENi-P-Al2O3 composite deposits on mild steel substrates at bath pH 5, 7 and 9. Study reveals that optimum deposit parameters and deposition rates are achieved with bath pH. However, not much study has been undertaken concerning composite deposits obtained from higher bath pH or basic bath. This is attributable to the fact that at higher bath pH or alkaline baths, the bath gets unstable and eventually degrades or decomposes, thereby resulting in sub optimal or poor deposition. Hence, experimental investigations carried out by preparing suitable baths, operating under optimum conditions, and enabling successful composite deposition in acidic and alkaline baths have revealed that there is a significant improvement in the above mentioned properties of the as-deposited composite deposits, as the pH is increased from pH 5 to pH 9. This aspect can therefore be advantageously utilized for preparing various marine components like fasteners, nuts, bolts, washers, pipes, cables, components having relative motion etc.

In-situ deposition of apatite layer to protect Mg-based composite fabricated via laser additive manufacturing

Biodegradable magnesium(Mg) and its alloy show huge potential as temporary bone substitute due to the favorable biocompatibility and mechanical compatibility. However, one issue deserves attention is the too fast degradation. In this work, mesoporous bioglass(MBG)with high pore volume(0.59 cc/g) and huge specific surface area(110.78 m^(2)/g) was synthesized using improved sol-gel method, and introduced into Mg-based composite via laser additive manufacturing. Immersion tests showed that the incorporated MBG served as powerful adsorption sites, which promoted the in-situ deposition of apatite by successively adsorbing Ca2+and HPO42-. Such dense apatite film acted as an efficient protection layer and enhanced the corrosion resistance of Mg matrix, which was proved by the electrochemical impedance spectroscopy measurements. Thereby, Mg based composite showed a significantly decreased degradation rate of 0.31 mm/year. Furthermore,MBG also improved the mechanical properties as well as cell behavior. This work highlighted the advantages of MBG in the fabrication of Mg-based implant with enhanced overall performance for orthopedic application.

Review on laser directed energy deposited aluminum alloys

Lightweight aluminum(Al)alloys have been widely used in frontier fields like aerospace and automotive industries,which attracts great interest in additive manufacturing(AM)to process high-value Al parts.As a mainstream AM technique,laser-directed energy deposition(LDED)shows good scalability to meet the requirements for large-format component manufacturing and repair.However,LDED Al alloys are highly challenging due to their inherent poor printability(e.g.low laser absorption,high oxidation sensitivity and cracking tendency).To further promote the development of LDED high-performance Al alloys,this review offers a deep understanding of the challenges and strategies to improve printability in LDED Al alloys.The porosity,cracking,distortion,inclusions,element evaporation and resultant inferior mechanical properties(worse than laser powder bed fusion)are the key challenges in LDED Al alloys.Processing parameter optimizations,in-situ alloy design,reinforcing particle addition and field assistance are the efficient approaches to improving the printability and performance of LDED Al alloys.The underlying correlations between processes,alloy innovation,characteristic microstructures,and achievable performances in LDED Al alloys are discussed.The benchmark mechanical properties and primary strengthening mechanism of LDED Al alloys are summarized.This review aims to provide a critical and in-depth evaluation of current progress in LDED Al alloys.Future opportunities and perspectives in LDED high-performance Al alloys are also outlined.

A Single-Layer Piezoelectric Composite Separator for Durable Operation of Li Metal Anode at High Rates

Piezoelectric ceramic and polymeric separators have been proposed to effectively regulate Li deposition and suppress dendrite growth,but such separators still fail to satisfactorily support durable operation of lithium metal batteries owing to the fragile ceramic layer or low-piezoelectricity polymer as employed.Herein,by combining PVDF-HFP and ferroelectric BaTiO_(3),we develop a homogeneous,single-layer composite separator with strong piezoelectric effects to inhibit dendrite growth while maintaining high mechanical strength.As squeezed by local protrusion,the polarized PVDF-HFP/BaTiO_(3)composite separator generates a local voltage to suppress the local-intensified electric field and further deconcentrate regional lithium-ion flux to retard lithium deposition on the protrusion,hence enabling a smoother and more compact lithium deposition morphology than the unpoled composite separator and the pure PVDF-HFP separator,especially at high rates.Remarkably,the homogeneous incorporation of BaTiO_(3)highly improves the piezoelectric performances of the separator with residual polarization of 0.086 pC cm^(-2)after polarization treatment,four times that of the pure PVDF-HFP separator,and simultaneously increases the transference number of lithium-ion from 0.45 to 0.57.Beneficial from the prominent piezoelectric mechanism,the polarized PVDF-HFP/BaTiO_(3)composite separator enables stable cyclic performances of Li||LiFePO_(4)cells for 400 cycles at 2 C(1 C=170 mA g^(-1))with a capacity retention above 99%,and for 600 cycles at 5 C with a capacity retention over 85%.

Electrolytic Co-Deposition Mechanisms, Texture Layers, and Residual Stresses in Nanocomposite Coatings Processes: A Review

The composite coating has gained wider attention due to its property to protect materials used in energy, bridges, offshore platforms, underground pipelines, and the aviation industry from corrosion and deterioration. In this work, a literature review was conducted about the processes of nanocomposite coating, the mechanisms of electrolytic co-deposition, the texture of layers, and the residual stresses. An important aspect, residual stress, was emphasized, which represents the persistent stress after removing the external force affecting a metal in the plastic region. Because it cannot be measured directly and may be determined by measuring strain and indirect methods, the sources and methods for measuring residual stresses (XRD, SEM, TEM, EDS) were described in the last section to provide a comprehensive overview. Based on the thorough analysis of the published literature, it was concluded that nanoparticles could be electrodeposited with Ni on an Al substrate using a direct current and Ni sulfamate as an electrolytic solution, and Nickel will not reside on the oxide layer covering Al, so chemical changes are needed to prepare the Al surface. In addition, texture changes with the thickness of the coated layer must be investigated.

Properties of Zn-Bi composite coatings prepared by ionic co-discharge deposition

Zn-Bi composite was synthesized by ionic co-discharge deposition and its properties were investigated. The results show that the Zn-Bi composite with the incorporation of Bi has a finer grain size than the pure Zn coating and improves the mechanical properties. The microhardness is increased by approximately two times simply by adding a small amount of Bi electrolyte into a Zn bath solution. A lower volume loss of the Zn-Bi composite coating compared with the pure Zn coating also indicates that the Zn-Bi coating has a better wear resistance.

Effect of ball peening of substrate on microstructure, phase evolution and properties of electrophoretically deposited YSZ/(Ni,Al) composite coatings

YSZ/（Ni, Al） composite coatings were deposited on Inconel600 superalloy with ball peening （BP） and without （non BP）treatment using the electrophoretic deposition （EPD） technique, followed by vacuum sintering method. The structures and phaseevolution of the coatings were studied with X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersivespectrometry （EDS）. The relation between microstructures and properties of the BPs-coated samples was discussed. The results showthat the adhesion strength and gain mass of the BPs-coated samples with isothermal oxidation at 1100℃ for 100 h are 3.3 N and0.00817 mg/cm^2, respectively, while those of the non-BPs-coated sample are 2.6 N and 0.00559 mg/cm^2, respectively. The EDSmapping analysis indicates that an obvious outward diffusion of Cr from the substrate to BPs coated samples occurs after isothermaloxidation. The BPs-coated sample shows the superior adhesion and oxidation resistance compared with non-BPs-coated samples.

Wear resistance of Zr/WC composite coatings on Cr12MoV steel surface by electric spark deposition

Zr/WC composite coating was prepared on the surface of Cr12MoV steel by electric spark deposition technology to change its surface properties. The surface and worn surface morphology of the coating were observed using scanning electron microscope. Dry friction and wear tests of the coatings were carried out at room temperature. The results show that the coating is continuous and uniform, and the thickness was about 50-60 μm. The microhardness of the coating surface was highest at 1140 HV_(200g), which was significantly higher than that of the substrate. The ear tests results show that the wear weight loss, wear volume and wear rate follow the following rules: Cr12MoV>WC coating> Zr/WC composite coating.

Direct deposition of graphene nanowalls on ceramic powders for the fabrication of a ceramic matrix composite

Uniform mixing of ceramic powder and graphene is of great importance for producing ceramic matrix composite. In this study, graphene nanowalls(GNWs) are directly deposited on the surface of Al2 O3 and Si3 N4 powders using chemical vapor deposition system to realize the uniform mixing. The morphology and the initial stage of the growth process are investigated. It is found that the graphitic base layer is initially formed parallel to the powder surface and is followed by the growth of graphene nanowalls perpendicular to the surface. Moreover, the lateral length of the graphene sheet could be well controlled by tuning the growth temperature. GNWs/Al2 O3 powder is consolidated by using sparking plasma sintering method and several physical properties are measured. Owing to the addition of GNWs, the electrical conductivity of the bulk alumina is significantly increased.

Wear mechanism for spray deposited Al-Si/SiC_p composites under dry sliding condition

Al-Si/15%SiCp(volume fraction) composites with different silicon contents were fabricated by spray deposition technique, and typical microstructures of these composites were studied by optical microscopy(OM). Dry sliding wear tests were carried out using a block-on-ring wear machine to investigate the effect of applied load range of 10-220 N on the wear and friction behavior of these composites sliding against SAE 52100 grade bearing steel. Scanning electron microscopy(SEM) and energy-dispersive X-ray microanalysis(EDAX) were utilized to examine the morphologies of the worn surfaces in order to observe the wear characteristics and investigate the wear mechanism. The results show that the wear behavior of these composites is dependent on the silicon content in the matrix alloy and the applied load. Al-Si/15%SiCp composites with higher silicon content exhibit better wear resistance in the applied load range. Under lower loads, the major wear mechanisms are oxidation wear and abrasive wear for all tested composites. Under higher loads, severe adhesive wear becomes the main wear mechanisms for Al-7Si/15%SiCp and Al-13Si/15%SiCp composites, while Al-20Si/15%SiCp presents a compound wear mechanism, consisting of oxidation, abrasive wear and adhesion wear.

Growth of BaTiO_3-Ag hybrid composite films at room temperature by aerosol deposition

Barium titanate (BaTiO3) and silver (Ag) composite film with high dielectric constant was grown at room temperature by an aerosol deposition method.The dielectric constant increases by 0.5 times after adding Ag to the BaTiO3 matrix,compared with pure BaTiO3.The high dielectric constant can be attributed to the percolation effect of Ag inclusions in the BaTiO3 matrix.The Ag was present in the form of discrete layer in the BaTiO3 film.The dielectric properties of BaTiO3 Ag were discussed in detail taking into account the changes in microstructures.

Study on the Structures and Properties of Ni-W-B-CeO_2 Composite Coatings Prepared by Pulse Electrodeposition

The aim of this research is to pulse co-deposit nano-CeO2 particles into Ni-W-B alloy coatings in order to improve the surface properties. The influence of pulse frequency and duty circle on deposition rate, microhardness and microstructures, and the influence of heat treatment temperature on phase structures, microhardness and abrasivity of Ni-W-B-CeO2 composite coatings were investigated. The results indicated that the pulse co-deposition of nickel, tungsten, boron and nano-CeO2 particle from the bath which nano-CeO2 particle was suspended by high speed mechanical stirring led to the Ni-W-B-CeO2 composite coatings, possessing better microhardness and abrasion resistance when heat-treated at 400 ℃ for 1 h. The microhardness as-deposited with 636 Hz and the deposition rate with 0.0281 mm·h-1 was the highest at pulse frequency with 1000 Hz and pulse duty circle with 10%. Microstructures analysis displays that decreasing pulse duty cycle leads to refinement in grain structures and the improvement of microstructures. X-ray diffraction shows that the composite coating as-deposited was mainly in the amorphous state and partially crystallized, but when heat treated at 400 ℃, the crystallization trend was strengthened further.

In situ TiB2/Cu composites fabricated by spray deposition using solid-liquid and liquid-liquid reactions

In situ TiB2/Cu composites were fabricated by both solid-liquid(S-L)and liquid-liquid(L-L)reactive spray deposition in combination with cold rolling and annealing.The microstructure and properties of the fabricated TiB2/Cu composites were investigated.The results show that the reactive mode and rolling treatment are the main factors affecting the microstructure and properties of the TiB2/Cu composite.The in situ reaction in the L-L reaction can be carried out more completely.By controlling the rolling and annealing process,the relative density and the properties of the as-deposited composites are optimized.The comprehensive performance of the deformed TiB2/Cu composite prepared by L-L reactive spray deposition(401 MPa and 83.5%IACS)is better than that by S-L reactive spray deposition(520 MPa and 20.2%IACS).

PREPARATION OF 6066 Al/SiC_p(+Gr) COMPOSITES BY MULTI-LAYER SPRAY DEPOSITION

ＰＲＥＰＡＲＡＴＩＯＮＯＦ６０６６Ａｌ／ＳｉＣ_ｐ（＋Ｇｒ）ＣＯＭＰＯＳＩＴＥＳＢＹＭＵＬＴＩ－ＬＡＹＥＲＳＰＲＡＹＤＥＰＯＳＩＴＩＯＮ￥ＣｈｅｎＺｈｅｎｈｕａ；ＺｈａｎｇＨａｏ；ＣｈｅｎＧａｎｇ；ＬｉｕＱｉｕｌｉｎ；ＳｕｎＺｈａｎｇｍｉｎｇ；Ｙａｎ?..

Preparation and characteristics of C/C composite brake disc by multi-cylindrical chemical vapor deposition processes

The C/C composite brake discs were prepared by tri-cylindrical chemical vapor deposition （CVD） process. The optimum processing parameters were as follows： deposition temperature was 830 - 930 ℃, the gas- flow rates of N2 and propylene were 4.8 - 5.2 m^3/h and 5.8 - 6.2 m^3/h, respectively, the furnace pressure was 4.5 - 5.5 kPa and the deposition time was 200 h. The effects of processing parameters on the densified rates, thermal-physical property and mechanical performance of C/C composite brake discs were studied. The results show that density, heat conductivity, bend strength and abrasion ratio of the multi-cylindrica brake discs are 1. 02 - 1. 78 g/cm^3 , 31 W/（m·K）, 114 MPa and 7μm/s, respectively, which are approximately similar to those of the singlecylindrical ones. The gas tlow rate has no relation to the number of the cylinder and furnace loading. The utilization ratio of carbon can be improved by multi-cylinder CVD process without changing the characteristics of brake disc.