In order to improve the effectiveness of traditional time domain identification methods in identifying damping ratios, a new damping ratio identification method based on pattern search is proposed by fluctuating the r...In order to improve the effectiveness of traditional time domain identification methods in identifying damping ratios, a new damping ratio identification method based on pattern search is proposed by fluctuating the reliable natural frequency obtained through traditional time domain identification methods by about 10% to build the boundary conditions, using all the initial identification results to establish the free decay response of the system, and using the pattern search method to correct the initial identification results with the residual sum of squares between the free decay response and the actually measured free-decay signal as the objective function. The proposed method deals with the actually measured free-decay signal with curve fitting and avoids enlarging the identified error caused by intermediate conversion, so it can effectively improve the identified accuracy of damping ratios. Simulations for a room-sized vibration isolation foundation show that the relative errors of analyzed three damping ratios are down to 1.05%, 1.51% and 3.7% by the proposed method from 8.42%, 5.85% and 8.5% by STD method when the noise level is 10%.展开更多
A model to describe the hysteresis damping characteristic of rubber material was presented.It consists of a parallel spring and damper,whose coefficients change with the vibration amplitude and frequency.In order to a...A model to describe the hysteresis damping characteristic of rubber material was presented.It consists of a parallel spring and damper,whose coefficients change with the vibration amplitude and frequency.In order to acquire these relations,force decomposition was carried out according to some sine vibration measurement data of nonlinear forces changing with the deformation of the rubber material.The nonlinear force is decomposed into a spring force and a damper force,which are represented by the amplitude-and frequency-dependent spring and damper coefficients,respectively.Repeating this step for different measurements gives different coefficients corresponding to different amplitudes and frequencies.Then,the application of a parameter identification method provides the requested approximation functions over amplitude and frequency.Using those formulae,as an example,the dynamic characteristic of a hollow shaft system supported by rubber rings was analyzed and the acceleration response curve in the centroid position was calculated.Comparisons with the sine vibration experiments of the real system show a maximal inaccuracy of 8.5%.Application of this model and procedure can simplify the modeling and analysis of mechanical systems including rubber materials.展开更多
基金Sponsored by the National Natural Science Foundation of China (Grant No.50675052)
文摘In order to improve the effectiveness of traditional time domain identification methods in identifying damping ratios, a new damping ratio identification method based on pattern search is proposed by fluctuating the reliable natural frequency obtained through traditional time domain identification methods by about 10% to build the boundary conditions, using all the initial identification results to establish the free decay response of the system, and using the pattern search method to correct the initial identification results with the residual sum of squares between the free decay response and the actually measured free-decay signal as the objective function. The proposed method deals with the actually measured free-decay signal with curve fitting and avoids enlarging the identified error caused by intermediate conversion, so it can effectively improve the identified accuracy of damping ratios. Simulations for a room-sized vibration isolation foundation show that the relative errors of analyzed three damping ratios are down to 1.05%, 1.51% and 3.7% by the proposed method from 8.42%, 5.85% and 8.5% by STD method when the noise level is 10%.
基金Project(50675042) supported by the National Natural Science Foundation of China
文摘A model to describe the hysteresis damping characteristic of rubber material was presented.It consists of a parallel spring and damper,whose coefficients change with the vibration amplitude and frequency.In order to acquire these relations,force decomposition was carried out according to some sine vibration measurement data of nonlinear forces changing with the deformation of the rubber material.The nonlinear force is decomposed into a spring force and a damper force,which are represented by the amplitude-and frequency-dependent spring and damper coefficients,respectively.Repeating this step for different measurements gives different coefficients corresponding to different amplitudes and frequencies.Then,the application of a parameter identification method provides the requested approximation functions over amplitude and frequency.Using those formulae,as an example,the dynamic characteristic of a hollow shaft system supported by rubber rings was analyzed and the acceleration response curve in the centroid position was calculated.Comparisons with the sine vibration experiments of the real system show a maximal inaccuracy of 8.5%.Application of this model and procedure can simplify the modeling and analysis of mechanical systems including rubber materials.
