A Two-Layer Fuzzy Control Strategy for the Participation of Energy Storage Battery Systems in Grid Frequency Regulation

To address the frequency fluctuation problem caused by the power dynamic imbalance between the power system and the loadwhen a large number of newenergy sources are connected to the grid,a two-layer fuzzy control strategy is proposed for the participation of the energy storage battery system in FM.Firstly,considering the coordination of FM units responding to automatic power generation control commands,a comprehensive allocation strategy of two signals under automatic power generation control commands is proposed to give full play to the advantages of two FM signals while enabling better coordination of two FM units responding to FM commands;secondly,based on the grid FM demand and battery FM capability,a double-layer fuzzy control strategy is proposed for FM units responding to automatic power generation control commands in a coordinated manner under dual-signal allocation mode to precisely allocate the power output depth of FM units,which can control the fluctuation of frequency deviation within a smaller range at a faster speed while maintaining the battery charge state;finally,the proposed Finally,the proposed control strategy is simulated and verified inMatlab/Simulink.The results show that the proposed control strategy can control the frequency deviation within a smaller range in a shorter time,better stabilize the fluctuation of the battery charge level,and improve the utilization of the FM unit.

An Investigation of Battery Energy Storage Aided Wind-Coal Integrated Energy System

This paper studies the feasibility of a supply-side wind-coal integrated energy system.Based on grid-side data,the load regulation model of coal-fired power and the wind-coal integrated energy system model are established.According to the simulation results,the reasons why the wind-coal combined power supply is difficult to meet the grid-side demand are revealedthrough scenario analysis.Basedon thewind-coal combinedoperation,a wind-coalstorage integrated energy system was proposed by adding lithium-iron phosphate battery energy storage system(LIPBESS)to adjust the load of the system.According to the four load adjustment scenarios of grid-side instructions of the wind-coal system,the difficulty of load adjustment in each scenario is analyzed.Based on the priority degree of LIPBESS charge/discharge in four scenarios at different time periods,the operation mode of two charges and two discharges per day was developed.Based on the independent operation level of coal-fired power,after the addition of LIPBESS(5.5 MWh),the average qualified rate of multi-power operation in March and June reached the level of independent operation of coal-fired power,while the average qualified rate of the remaining months was only 5.4%different from that of independent operation of coal-fired power.Compared with the wind storage mode,the energy storage capacity and investment cost of wind-coal-storage integrated energy system are reduced by 54.2%and 53.7%,respectively.

A novel coordinated control strategy considering power smoothing for a hybrid photovoltaic/battery energy storage system

This work presents a novel coordinated control strategy of a hybrid photovoltaic/battery energy storage(PV/BES) system. Different controller operation modes are simulated considering normal, high fluctuation and emergency conditions. When the system is grid-connected, BES regulates the fluctuated power output which ensures smooth net injected power from the PV/BES system. In islanded operation, BES system is transferred to single master operation during which the frequency and voltage of the islanded microgrid are regulated at the desired level. PSCAD/EMTDC simulation validates the proposed method and obtained favorable results on power set-point tracking strategies with very small deviations of net output power compared to the power set-point. The state-of-charge regulation scheme also very effective with SOC has been regulated between 32% and 79% range.

A distributed VSG control method for a battery energy storage system with a cascaded H-bridge in a grid-connected mode

With the high penetration of renewable energy,new challenges,such as power fluctuation suppression and inertial support capability,have arisen in the power sector.Battery energy storage systems play an essential role in renewable energy integration.In this paper,a distributed virtual synchronous generator(VSG)control method for a battery energy storage system(BESS)with a cascaded H-bridge converter in a grid-connected mode is proposed.The VSG is developed without communication dependence,and state-of-charge(SOC)balancing control is achieved using the distributed average algorithm.Owing to the low varying speed of SOC,the bandwidth of the distributed communication networks is extremely slow,which decreases the cost.Therefore,the proposed method can simultaneously provide inertial support and accurate SOC balancing.The stability is also proved using root locus analysis.Finally,simulations under different conditions are carried out to verify the effectiveness of the proposed method.

Battery Energy Storage to Strengthen the Wind Generator in Integrated Power System

The wind energy generation,utilization and its grid penetration in electrical grid are increasing world-wide.The wind generated power is always fluctuating due to its time varying nature and causing stability problem.This weak interconnection of wind generating source in the electrical network affects the power quality and reliability.The localized energy storages shall compensate the fluctuating power and support to strengthen the wind generator in the power system.In this paper,it is proposed to control the voltage source inverter （VSI） in current control mode with energy storage,that is,batteries across the dc bus.The generated wind power can be extracted under varying wind speed and stored in the batteries.This energy storage maintains the stiff voltage across the dc bus of the voltage source inverter.The proposed scheme enhances the stability and reliability of the power system and maintains unity power factor.It can also be operated in stand-alone mode in the power system.The power exchange across the wind generation and the load under dynamic situation is feasible while maintaining the power quality norms at the common point of coupling.It strengthens the weak grid in the power system.This control strategy is evaluated on the test system under dynamic condition by using simulation.The results are verified by comparing the performance of controllers.

Multifunction Battery Energy Storage System for Distribution Networks

Battery Energy Storage System(BESS)is one of the potential solutions to increase energy system flexibility,as BESS is well suited to solve many challenges in transmission and distribution networks.Examples of distribution network’s challenges,which affect network performance,are:(i)Load disconnection or technical constraints violation,which may happen during reconfiguration after fault,(ii)Unpredictable power generation change due to Photovoltaic(PV)penetration,(iii)Undesirable PV reverse power,and(iv)Low Load Factor(LF)which may affect electricity price.In this paper,the BESS is used to support distribution networks in reconfiguration after a fault,increasing Photovoltaic(PV)penetration,cutting peak load,and loading valley filling.The paper presents a methodology for BESS optimal locations and sizing considering technical constraints during reconfiguration after a fault and PV power generation changes.For determining themaximumpower generation change due to PV,actual power registration of connected PV plants in South Cairo Electricity Distribution Company(SCEDC)was considered for a year.In addition,the paper provides a procedure for distribution network operator to employ the proposed BESS to perform multi functions such as:the ability to absorb PV power surplus,cut peak load and fill load valley for improving network’s performances.The methodology is applied to a modified IEEE 37-node and a real network part consisting of 158 nodes in SCEDC zone.The simulation studies are performed using the DIgSILENT PowerFactory software andDPL programming language.The Mixed Integer Linear Programming optimization technique(MILP)in MATLAB is employed to choose the best locations and sizing of BESS.

Typical Application Scenarios and Economic Benefit Evaluation Methods of Battery Energy Storage System

Energy storage system is an important means to improve the flexibility and safety of traditional power system,but it has the problem of high cost and unclear value recovery path.In this paper,the typical application scenarios of energy storage system are summarized and analyzed from the perspectives of user side,power grid side and power generation side.Based on the typical application scenarios,the economic benefit assessment framework of energy storage system including value,time and efficiency indicators is proposed.Typical battery energy storage projects are selected for economic benefit calculation according to different scenarios,and key factors are selected for sensitivity analysis.Finally,the key factors affecting economic benefit of the energy storage system are analyzed.

Multi-Scale Fusion Model Based on Gated Recurrent Unit for Enhancing Prediction Accuracy of State-of-Charge in Battery Energy Storage Systems

Accurate prediction of the state-of-charge(SOC)of battery energy storage system(BESS)is critical for its safety and lifespan in electric vehicles.To overcome the imbalance of existing methods between multi-scale feature fusion and global feature extraction,this paper introduces a novel multi-scale fusion(MSF)model based on gated recurrent unit(GRU),which is specifically designed for complex multi-step SOC prediction in practical BESSs.Pearson correlation analysis is first employed to identify SOC-related parameters.These parameters are then input into a multi-layer GRU for point-wise feature extraction.Concurrently,the parameters undergo patching before entering a dual-stage multi-layer GRU,thus enabling the model to capture nuanced information across varying time intervals.Ultimately,by means of adaptive weight fusion and a fully connected network,multi-step SOC predictions are rendered.Following extensive validation over multiple days,it is illustrated that the proposed model achieves an absolute error of less than 1.5%in real-time SOC prediction.

Massive energy storage system for effective usage of renewable energy

The current energy trend indicates a strong thrust toward transforming renewable energy as a major power source.To achieve this mission,battery energy storage systems(BESSs)are indispensable.Although BESSs are expensive,cost reduction can be achieved by using BESSs for multiple purposes,such as load leveling,business continuity planning,frequency control,capacity market,arbitrage,and emergency power.In this paper,various applications of BESSs are classified.The possibility of achieving conflict-free combination of different applications is demonstrated.The total required energy storage capacity in Japan is estimated to be 150–200 GWh by 2030.The present status of NaS batteries for multipurpose use and new trends in battery-based businesses are introduced.

A PI+R Control Scheme Based on Multi-Agent Systems for Economic Dispatch in Isolated BESSs

Battery energy storage systems(BESSs)are widely used in smart grids.However,power consumed by inner impedance and the capacity degradation of each battery unit become particularly severe,which has resulted in an increase in operating costs.The general economic dispatch(ED)algorithm based on marginal cost(MC)consensus is usually a proportional(P)controller,which encounters the defects of slow convergence speed and low control accuracy.In order to solve the distributed ED problem of the isolated BESS network with excellent dynamic and steady-state performance,we attempt to design a proportional integral(PI)controller with a reset mechanism(PI+R)to asymptotically promote MC consensus and total power mismatch towards 0 in this paper.To be frank,the integral term in the PI controller is reset to 0 at an appropriate time when the proportional term undergoes a zero crossing,which accelerates convergence,improves control accuracy,and avoids overshoot.The eigenvalues of the system under a PI+R controller is well analyzed,ensuring the regularity of the system and enabling the reset mechanism.To ensure supply and demand balance within the isolated BESSs,a centralized reset mechanism is introduced,so that the controller is distributed in a flow set and centralized in a jump set.To cope with Zeno behavior and input delay,a dwell time that the system resides in a flow set is given.Based on this,the system with input delays can be reduced to a time-delay free system.Considering the capacity limitation of the battery,a modified MC scheme with PI+R controller is designed.The correctness of the designed scheme is verified through relevant simulations.

Virtual Transmission Solution Based on Battery Energy Storage Systems to Boost Transmission Capacity

The increasing penetration of variable renewable energy(VRE)generation along with the decommissioning of conventional power plants in Chile,has raised several operational challenges in the Chilean National Power Grid(NPG),including transmission congestion and VRE curtailment.To mitigate these limitations,an innovative virtual transmission solution based on battery energy storage systems(BESSs),known as grid booster(GB),has been proposed to increase the capacity of the main 500 kV corridor of the NPG.This paper analyzes the dynamic performance of the GB using a wide-area electromagnetic transient(EMT)model of the NPG.The GB project,composed of two 500 MVA BESS units at each extreme of the 500 kV corridor,allows increasing the transmission capacity for 15 min during N-1 contingencies,overcoming transmission limitations under normal operation conditions while maintaining system stability during faults.The dynamic behavior of the GB is also analyzed to control power flow as well as voltage stability.The results show that the GB is an effective solution to allow greater penetration of VRE generation while maintaining system stability in the NPG.

Improved Energy Management Strategy for Prosumer Buildings with Renewable Energy Sources and Battery Energy Storage Systems

The concept of utilizing microgrids(MGs)to convert buildings into prosumers is gaining massive popularity because of its economic and environmental benefits.These pro-sumer buildings consist of renewable energy sources and usually install battery energy storage systems(BESSs)to deal with the uncertain nature of renewable energy sources.However,because of the high capital investment of BESS and the limitation of available energy,there is a need for an effective energy management strategy for prosumer buildings that maximizes the profit of building owner and increases the operating life span of BESS.In this regard,this paper proposes an improved energy management strategy(IEMS)for the prosumer building to minimize the operating cost of MG and degradation factor of BESS.Moreover,to estimate the practical operating life span of BESS,this paper utilizes a non-linear battery degradation model.In addition,a flexible load shifting(FLS)scheme is also developed and integrated into the proposed strategy to further improve its performance.The proposed strategy is tested for the real-time annual data of a grid-tied solar photovoltaic(PV)and BESS-powered AC-DC hybrid MG installed at a commercial building.Moreover,the scenario reduction technique is used to handle the uncertainty associated with generation and load demand.To validate the performance of the proposed strategy,the results of IEMS are compared with the well-established energy management strategies.The simulation results verify that the proposed strategy substantially increases the profit of the building owner and operating life span of BESS.Moreover,FLS enhances the performance of IEMS by further improving the financial profit of MG owner and the life span of BESS,thus making the operation of prosumer building more economical and efficient.

An Analytical Method for Delineating Feasible Region for PV Integration Capacities in Net-zero Distribution Systems Considering Battery Energy Storage System Flexibility

To provide guidance for photovoltaic(PV)system integration in net-zero distribution systems(DSs),this paper proposes an analytical method for delineating the feasible region for PV integration capacities(PVICs),where the impact of battery energy storage system(BESS)flexibility is considered.First,we introduce distributionally robust chance constraints on network security and energy/carbon net-zero requirements,which form the upper and lower bounds of the feasible region.Then,the formulation and solution of the feasible region is proposed.The resulting analytical expression is a set of linear inequalities,illustrating that the feasible region is a polyhedron in a high-dimensional space.A procedure is designed to verify and adjust the feasible region,ensuring that it satisfies network loss constraints under alternating current(AC)power flow.Case studies on the 4-bus system,the IEEE 33-bus system,and the IEEE 123-bus system verify the effectiveness of the proposed method.It is demonstrated that the proposed method fully captures the spatio-temporal coupling relationship among PVs,loads,and BESSs,while also quantifying the impact of this relationship on the boundaries of the feasible region.

Dynamic Economic Dispatch for Microgrids Including Battery Energy Storage

Microgrids integrate distributed renewable energy resources, controllable loads and energy storage in a more economic and reliable fashion. Battery energy storage units are essential for microgrid operation, which make microgird become a strong coupling system in the time domain. Hence, the traditional methods of static dispatch are no longer suitable for microgrids. This paper proposes a dynamic economic dispatch method for microgrids. Considering microgrid as a discrete time system, the dynamic economic dispatch is to find the optimal control strategy for the system in finite time period. Based on this idea, the dynamic economic dispatch model for microgrids is established, and then the corresponding dynamic programming algorithm is designed. Finally, an example of microgrid is given, and the dynamic economic dispatch results are compared with that of the static dispatch. The comparison confirms the effectiveness of the proposed dynamic dispatch method.

Deep reinforcement learning for online scheduling of photovoltaic systems with battery energy storage systems

A new online scheduling algorithm is proposed for photovoltaic(PV)systems with battery-assisted energy storage systems(BESS).The stochastic nature of renewable energy sources necessitates the employment of BESS to balance energy supplies and demands under uncertain weather conditions.The proposed online scheduling algorithm aims at minimizing the overall energy cost by performing actions such as load shifting and peak shaving through carefully scheduled BESS charging/discharging activities.The scheduling algorithm is developed by using deep deterministic policy gradient(DDPG),a deep reinforcement learning(DRL)algorithm that can deal with continuous state and action spaces.One of the main contributions of this work is a new DDPG reward function,which is designed based on the unique behaviors of energy systems.The new reward function can guide the scheduler to learn the appropriate behaviors of load shifting and peak shaving through a balanced process of exploration and exploitation.The new scheduling algorithm is tested through case studies using real world data,and the results indicate that it outperforms existing algorithms such as Deep Q-learning.The online algorithm can efficiently learn the behaviors of optimum non-casual off-line algorithms.

Energy Storage and Multi-Source System for Reduction Energy Costs in the Consumer-Side

The objective of this work is to reduce energy costs for a consumer with multiple available energy resources and with an energy storage system. To achieve this, it is developed a methodology with a multi-criterion analysis that considers the demand side, the real-time prices, and the availability of the energy resources. In other words, the developed methodology manages the multi-source system, allowing savings for a consumer. In addition to the presentation of the methodology, it is made an application in a case study. It is considered and modeled a real consumer that has three different energy resources, including energy storage by battery. The situation comprehends solar generation, diesel generator and the electrical power grid. There are simulations and the results comprehend the savings for this consumer, considering the methodology application. The main result is a reduction in energy costs by 33.3%, considering the situation without this methodology. For the purpose of indicating the use of the storage system, it is presented the battery’s state of charge along the simulation. Also, there is a verification of the methodology’s robustness, through another simulation, using theoretical data for the consumer. In this case, the consumer has energy storage system, solar generation, biogas generator and the electrical power grid. In this situation, there is a reduction in energy costs by 30.2%, considering the situation without this methodology. In conclusion, the results show that the developed methodology is effective. In the two case studies presented there are significant savings for the consumer.

MXene-based materials for electrochemical energy storage

Rechargeable batteries and supercapacitors are widely investigated as the most important electrochemical energy storage devices nowadays due to the booming energy demand for electric vehicles and hand-held electronics. The large surface-area-to-volume ratio and internal surface areas endow two-dimensional（2D） materials with high mobility and high energy density; therefore, 2D materials are very promising candidates for Li ion batteries and supercapacitors with comprehensive investigations. In 2011, a new kind of 2D transition metal carbides, nitrides and carbonitrides, MXene, were successfully obtained from MAX phases. Since then about 20 different kinds of MXene have been prepared. Other precursors besides MAX phases and even other methods such as chemical vapor deposition（CVD） were also applied to prepare MXene, opening new doors for the preparation of new MXene. Their 2D nature and good electronic properties ensure the inherent advantages as electrode materials for electrochemical energy storage. In this review, we summarize the recent progress in the development of MXene with emphasis on the applications to electrochemical energy storage. Also, future perspective and challenges of MXene-based materials are briefly discussed regrading electrochemical energy storage.

Battery energy storage-based system damping controller for alleviating sub-synchronous oscillations in a DFIG-based wind power plant

This paper presents the issue of the Sub-synchronous resonance(SSR)phenomenon in a series compensated DFIG-based wind power plant and its alleviation using a Battery Energy Storage-based Damping Controller(BESSDCL).A supplementary damping signal is developed considering the angular speed deviation and is incorporated into the BESS control system.Wide-area Measurement System data is used to determine the angular speed deviation.A lin-earized system model is developed to perform eigenvalue analysis,and to detect and examine unstable SSR modes.The variation of wind speed and three-phase fault are also taken into consideration to validate the robustness of the controller.To further verify the efficacy of the proposed damping controller,time-domain simulations are performed using MATLAB/Simulink.The application of the proposed BESSDCL stabilizes all the unstable system modes effectively at wind speeds of 7 m/s,9 m/s,and 11 m/s,and at 40%,50%,and 60%series compensation levels,as well three-phase fault conditions.

Post lithium ion batteries for emerging energy storage technologies

It is obvious that in the next ten years,lithium ion batteries are still the dominating power source for a wide range of products including consumable electronics,vehicles(cars,motorbikes,scooters,buses),drones,and even robots and tanks.However,in the pursuit of cost-effective,safety-reliable,and highly efficient energy storage technologies,researchers are developing

Provision of Ramp-rate Limitation as Ancillary Service from Distribution to Transmission System:Definitions and Methodologies for Control and Sizing of Central Battery Energy Storage System

The variability of the output power of distributed renewable energy sources(DRESs)that originate from the fastchanging climatic conditions can negatively affect the grid stability.Therefore,grid operators have incorporated ramp-rate limitations(RRLs)for the injected DRES power in the grid codes.As the DRES penetration levels increase,the mitigation of high-power ramps is no longer considered as a system support function but rather an ancillary service(AS).Energy storage systems(ESSs)coordinated by RR control algorithms are often applied to mitigate these power fluctuations.However,no unified definition of active power ramps,which is essential to treat the RRL as AS,currently exists.This paper assesses the various definitions for ramp-rate RR and proposes RRL method control for a central battery ESS(BESS)in distribution systems(DSs).The ultimate objective is to restrain high-power ramps at the distribution transformer level so that RRL can be traded as AS to the upstream transmission system(TS).The proposed control is based on the direct control of theΔP/Δt,which means that the control parameters are directly correlated with the RR requirements included in the grid codes.In addition,a novel method for restoring the state of charge(So C)within a specific range following a high ramp-up/down event is proposed.Finally,a parametric method for estimating the sizing of central BESSs(BESS sizing for short)is developed.The BESS sizing is determined by considering the RR requirements,the DRES units,and the load mix of the examined DS.The BESS sizing is directly related to the constant RR achieved using the proposed control.Finally,the proposed methodologies are validated through simulations in MATLAB/Simulink and laboratory tests in a commercially available BESS.