Research on AC Electronic Load with Energy Recovery Based on Finite Control Set Model Predictive Control

Nowadays,AC electronic loads with energy recovery are widely used in the testing of uninterruptible power supplies and power supply equipment.To tackle the problems of control difficulty,strategy complexity,and poor dynamic performance of AC electronic load with energy recovery of the conventional control strategy,a control strategy of AC electronic load with energy recovery based on Finite Control Set Model Predictive Control(FCSMPC)is developed.To further reduce the computation burden of the FCS-MPC,a simplified FCS-MPC with transforming the predicted variables and using sector to select expected state is proposed.Through simplified model and equivalent approximation analysis,the transfer function of the system is obtained,and the stability and robustness of the system are analyzed.The performance of the simplified FCS-MPC is compared with space vector control(SVPWM)and conventional FCS-MPC.The results show that the FCS-MPC method performs better dynamic response and this advantage is more obvious when simulating high power loads.The simplified FCS-MPC shows similar control performance to conventional FCS-MPC at less computation burden.The control performance of the system also shows better simulation results.

Web Tension Regulation of Multispan Roll-to-Roll System using Integrated Active Dancer and Load Cells for Printed Electronics Applications

The mass production of primed electronics can be achieved by roll-to-roll（R2R） printing system, so highly accurate web tension is required that can minimize the register error and keep the thickness and roughness of printed devices in limits. The web tension of a R2R system is regulated by the use of integrated load cells and active dancer system for printed electronics applications using decentralized multi-input-single-output（MISO） regularized variable learning rate backpropagation artificial neural networks. The active dancer system is used before printing system to reduce disturbances in the web tension of process span. The classical PID control result in tension spikes with the change in roll diameter of winder and unwinder rolls. The presence of dancer in R2R system shows that improved web tension control in printing span and the web tension can be enhanced from 3.75 N to 4.75 N. The overshoot of system is less than ±2.5 N and steady state error is within ± 1 N where load cells have a signal noise of ±0.7 N. The integration of load cells and active dancer with self-adapting neural network control provide a solution to the web tension control of multispan roll-to-roll system.

Unbalanced Load Simulation of Electronic Power Transformer in Distribution System

A control scheme of electronic power transformer (EPT) in a three-phase four-wire distribution system, which included an input section, an isolating section and an output section, was researched under unbalanced loads. The simple and appropriate control scheme was developed through analyzing the system requirements of the primary side and the load requirements of the secondary side. In the input section, a dual-loop control in synchronous rotating d-q coordinates was introduced, and in the output section, a dual-loop control based on instantaneous output voltage was used. Load characteristics of EPT were investigated by using Matlab/Simulink software. Simulation results showed that, with the proposed control scheme, the EPT has good performances and the sinusoidal input current and constant output voltage can be realized under both balanced and unbalanced loads.

Review of Electronic Speckle Pattern Interferometry(ESPI) for Three Dimensional Displacement Measurement

Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorithms, several different 3D electronic speckle pattern interferometry（ESPl） systems for displacement and strain measurements have been achieved and commercialized. This paper provides a review of the recent developments in ESPI systems for 3D displacement and strain measurement. After an overview of the fundamentals of ESP! theory, temporal phase-shift, and spatial phase-shift techniques, 3D deformation measurements by the temporal phase-shift ESPI system, which is suited well for static measurement, and by the spatial phase-shift ESPI system, which is particularly useful for dynamic measurement, are discussed. For each method, the basic theory, a brief derivation and different optical layouts are presented. The state of art application, potential and limitation of the ESPI systems are shown and demonstrated.

Limit Load Solution for Electron Beam Welded Joints with Single Edge Weld Center Crack in Tension

Limit loads are widely studied and several limit load solutions are proposed to some typical geometry of weldments.However,there are no limit load solutions exist for the single edge crack weldments in tension（SEC（T））,which is also a typical geometry in fracture analysis.The mis-matching limit load for thick plate with SEC（T） are investigated and the special limit load solutions are proposed based on the available mis-matching limit load solutions and systematic finite element analyses.The real weld configurations are simplified as a strip,and different weld strength mis-matching ratio M,crack depth/width ratio a/W and weld width 2H are in consideration.As a result,it is found that there exists excellent agreement between the limit load solutions and the FE results for almost all the mis-matching ration M,a/W and ligament-to-weld width ratio（W-a）/H.Moreover,useful recommendations are given for evaluating the limit loads of the EBW structure with SEC（T）.For the EBW joints with SEC（T）,the mis-matching limit loads can be obtained assuming that the components are wholly made of base metal,when M changing from 1.6 to 0.6.When M decreasing to 0.4,the mis-matching limit loads can be obtained assuming that the components are wholly made of base metal only for large value of（W-a）/H.The recommendations may be useful for evaluating the limit loads of the EBW structures with SEC（T）.The engineering simplifications are given for assessing the limit loads of electron beam welded structure with SEC（T）.

Oxygen vacancies with localized electrons direct a functionalized separator toward dendrite-free and high loading LiFePO_(4)for lithium metal batteries

The pursuit of high energy density has promoted the development of high-performance lithium metal batteries(LMBs).However,the underestimated but non-negligible dendrites of Li anode have been observed to shorten battery lifespan.Herein,a composite separator(TiO_(2-x)@PP),in which TiO_(2)with electron-localized oxygen vacancies(TiO_(2-x))is coated on a commercial PP separator,is fabricated to homogenize lithium ion transport and stabilize the lithium anode interface.With the utilization of TiO_(2-x)@PP separators,the symmetric lithium metal battery displays enhanced cycle stability over 800 h under a high current density of 8 m A cm^(-2).Moreover,the LMBs assembled with high-loading LiFePO_(4)(9.24 mg cm^(-2))deliver a stable cycling performance over 900 cycles at a rate of 0.5 C.Comprehensive theoretical studies based on density functional theory(DFT)further unveil the mechanism.The favorable TiO_(2-x)is beneficial for facilitating fast Li+migration and impeding anions transfer.In addressing the Li dendrite issues,the use of TiO_(2-x)@PP separator potentially provides a facile and attractive strategy for designing well-performing LMBs,which are expected to meet the application requirements of rechargeable batteries.

CHARACTERISTICS OF CYCLOTRON AUTORESONANCE MASER WITH A LARGE-ORBIT ELECTRON RING IN A PARTIALLY DIELECTRIC-LOADED WAVEGUIDE

The cyclotron autoresonace masers with a large-orbit electron ring in a dielectric-loaded waveguide have been analyzed.The stability properties are investigated self-consistentlyon the basis of the linearized Vlasov-Maxwell equations.The numerical results show that thedielectric liner can greatly reduce the energy of the electron beam,and a novel effective radiationdevice with low electron beam energy in the millimeter and submillimeter wave region have beenproposed.

一种L波段300W GaN脉冲功率模块

随着第三代半导体GaN器件技术的不断发展,GaN高电子迁移率晶体管(HEMT)在电子系统中逐步得到了广泛应用。研制了一款小型化L波段300 W GaN脉冲功率模块。研发了满足高压脉冲工作条件的GaN HEMT芯片,采用负载牵引技术进行了器件大信号阻抗参数提取,并以此为基础设计了小型化匹配网络进行阻抗变换。基于高压驱动芯片和开关器件芯片设计了小型化高压脉冲调制电路。测试结果表明,在工作频率990~1130 MHz、工作电压50 V、脉冲宽度100μs、占空比10%下,功率模块脉冲输出功率大于300 W,功率附加效率大于53%,功率增益大于38 dB。功率模块尺寸为30 mm×30 mm×8 mm。

高比例分布式电源配电网中低压柔性互联协调规划

柔性互联技术是解决高比例分布式电源(distributed generation,DG)配电网面临诸多问题的有效手段之一。提出了一种基于多层优化的配电网中压与低压柔性互联协调规划方法。首先,建立基于电力电子柔性互联设备(flexible interconnected devices,FID)的中低压柔性互联配电网潮流模型。然后,构建三层协调规划模型,上层以低压FID年运行成本及台区变压器负载率的年方差最小为目标,中层以中压FID年运行成本及从上级电网年购电成本最小为目标,分别决策低压和中压FID的安装位置与容量,下层以各场景的从上级电网购电成本最小为目标优化系统运行,并采用自适应粒子群优化和二阶锥规划相结合的混合算法求解。最后,采用含高比例DG的IEEE 33节点配电网进行算例分析,通过柔性互联规划系统的年综合运行成本降低了19.01%,台区变压器负载率的年方差减少了82.59%,验证了所提规划模型的有效性。

不均匀卵石持力层桩端后注浆效果试验研究

我国东南沿海尤其是温州地区广泛存在上覆深厚软土下覆不均匀卵石的地层。该区域的钻孔灌注桩常采用后注浆技术改善其承载性能。为了评价后注浆技术对这类地层中灌注桩承载力改善效果,开展了相应的模型试验,对比了不同注浆量对桩承载力的影响程度;并结合扫描电镜(scanning electron microscope,简称SEM)试验分析了浆液分布特点,探讨了浆液在卵石层中的扩散范围,研究了浆液扩散范围与桩承载力之间的关系。结果表明:浆液能够有效地填充桩端卵石层,注浆量的增加使得填充范围扩大,填充范围为3~4倍桩径时,桩的承载力改善最显著。在不均匀卵石持力层中存在一个最优注浆量,最优归一化注浆量约为2.8,若超过该最优注浆量归一化值,桩的承载力不再显著提高。单桩模型试验确定的最优注浆量与刘金砺公式[1]的预测结果接近。扫描电镜技术有助于评价桩的后注浆技术在上覆深厚软土下覆不均匀卵石的土层中的效果。

高能电子束辐照对黄精微生物及品质的影响

为探究高能电子束辐照对黄精的影响,以未辐照样品为对照,研究不同剂量(2、4、6、8、10 kGy)电子束辐照对黄精微生物含量、水分、总灰分、浸出物及色泽、挥发性物质的影响。结果表明,经2 kGy剂量辐照,黄精中微生物总数降低至《中国药典》要求限度;随着剂量增加,辐照杀菌效果更好。辐照对黄精水分和总灰分含量无显著影响(P>0.05)。辐照剂量≥4 kGy时,黄精浸出物含量、色度黄蓝值(b^(*)值)和饱和度显著增加(P<0.05),但不影响总色泽。辐照对黄精主要挥发性成分无明显影响,但在一定剂量下,会加速芳香成分、氮氧化合物、甲烷物质及醇类、醛酮类化合物挥发;主成分分析及线性判别分析表明,2 kGy剂量辐照对黄精挥发性影响最小。综合分析,2 kGy剂量高能电子束辐照能有效杀灭黄精中的微生物,且对其水分、总灰分、浸出物、色泽及挥发性成分无显著影响。

基于PSO改进BP算法的直流电子负载PID控制仿真

针对电子负载控制灵敏度低、稳定性差等问题,提出基于PSO-BP-PID的直流电子负载控制方法。分析电子负载基本结构,构建数学模型,分析电子负载在不同工作模式下的电流变化规律;建立三层BP网络模型,分别描述每层结构的输入与输出内容;为提高BP网络的学习能力,减少控制误差,将PSO算法作为学习算法,确定粒子群规模、惯性权重等重要参数,获得所有粒子适应度值,不断更新个体的位置与速度,当满足收敛条件时,输出最优解,实现控制参数的自适应调整;根据算法特征,设计控制器整体结构,利用该控制器即可实现直流电子负载控制。仿真结果表明,所提方法的控制误差小,响应速度快,且控制过程中能够有效抑制谐波。

单相PET级联整流SVPWM均压边界及拓展方法

电力电子变压器(power electronic transformer,PET)是交直流配电系统互联的重要接口设备,然而后级等效负载不平衡将造成前级整流器各模块的电压偏移。针对单相级联H桥整流器空间矢量调制均压失效问题,推导出基于最优矢量选择均压策略的边界计算方法。根据计算所得的负载不平衡度限制边界与级联模块数、调制度以及功率因数的关系,提出了变调制度和功率因数的控制策略以增加均压能力。该策略通过改变直流电压或降低功率因数来重建更宽的均压工作范围,确保原不平衡度均压极限的系统稳定运行。最后,通过三模块级联整流器的仿真与实验验证了该均压边界的正确性,以及所提均压拓展方法保障极端不平衡负载条件下均压的有效性。

冲击载荷作用下钽电容的电压瞬变特性及微观机理

为探究钽电容在冲击载荷作用下的失效机制,设计并开展了5组不同强度的钽电容水下爆炸冲击实验,研究了冲击载荷作用下钽电容的电压瞬变特性,通过漏电、充电电流变化分析了钽电容的失效模式,利用扫描电镜观察钽电容的微观结构,讨论了冲击载荷作用下钽电容的失效机理。结果表明:钽电容受冲击后发生短路失效,电压大幅度降低,在自愈完成后电压缓慢上升。随着冲击波超压的增大,钽电容失效的概率增大,钽电容失效的临界超压约为32 MPa。不同类型的电压变化对应不同的失效模式,包括击穿后瞬间自愈、击穿后缓慢自愈和多次击穿自愈。不同类型电压变化的初始漏电电流峰值有较大差别,Ⅰ类电流峰值为2.5~5 A,Ⅱ类为1~2 A,Ⅲ类为8~9 A,且峰值越大,峰宽越小。冲击载荷作用下钽电容的微观失效机理与其氧化膜的瑕疵相关,机理包括氧化膜中微裂缝扩展使得局部电场强度超过击穿场强造成击穿、氧化膜较薄区域下方的杂质及晶态膜突出形成导电通道、贯穿型裂缝形成后气体电离导致的击穿。

循环加卸载过程中灰岩微细观损伤特征的试验研究

岩石的动力学性质是影响岩质边坡地震动力稳定性的关键内因。地震产生的循环往复作用会造成岩石损伤和破坏,劣化岩石性能,降低岩质边坡的稳定性。为了深入研究岩石在动力荷载下的损伤特征,以某岩质斜坡出露的二叠系灰岩为研究对象,联合单轴循环加卸载试验和微细观试验,从微细观角度研究了岩样在循环加卸载过程中的损伤特征和损伤演化规律,分析了不同加载条件对微细观损伤的影响,开展了宏观和微细观参数的关联分析。研究结果表明:岩样内部的损伤是一个渐进性过程,在破坏前,随着应力幅值和循环周次的增加,表现为以小孔隙的生成、扩展和贯通为主,大孔隙的数量轻微增加且数量相对少得多;与变上限应力加载相比,变下限应力加载更有利于小孔隙的连通和大孔隙的形成,导致岩样内部微裂隙面积更大,在宏观上表现为平均弹性模量的降低;在变上限应力时,低应力幅值的循环荷载对岩石内部结构劣化效应比单轴压缩条件下的大,而高应力幅值的循环荷载反而可能对岩石内部孔隙有一定压密作用,导致孔隙度相对较小,劣化效应相对减弱;综合多种微细观损伤变量演化趋势,可判断岩样在循环加卸载下经历了一段裂纹稳定扩展的阶段,对应的上限应力和下限应力范围分别为(0.4~0.6)σ_(f)(σ_(f)为静态峰值强度)和(0.3~0.5)σ_(f)。研究成果有助于从微细观层次更好地理解岩石的动力学特性,为岩质斜坡在地震作用下的动力响应行为和灾害孕育及启动过程提供理论解释。

能量回馈型电子负载DC/AC并网变流器

为实现负载能量回馈,完成负载和电源间可靠和高效的电能回收,构建了能量回馈型电子负载的DC/AC并网变流器硬件电路及其控制算法。首先设计了包含功率因数校正(PFC)升压模块、DC/DC隔离模块、DC/AC转换模块和输出滤波器模块在内的DC/AC并网变流器硬件电路,然后建立了DC/AC并网变流器级联控制模型,随后提出了包含同步锁相环、电流内环和电压外环在内的DC/AC并网变流器PID控制策略,以实现交流电子负载中的能量回馈。最后,研制并测试了能量回馈型电子负载的DC/AC并网变流器,测试结果表明所研制设备能实现低总谐波畸变率(THD)并网,能量回收效率达到95%。

基于能馈型电子负载的简化双环控制策略

为了在简化控制的前提下提升能馈型电子负载后级的并网逆变环节性能,针对系统后级逆变环节双环控制系统进行了改进,在替换了电流内环的控制方式的前提下,参考万向节死锁的原理,通过拟似演化博弈的方式比较了电压外环受控参数的关系,对其进行了简化与寻优,仿真结果表明,所提出的控制方法相较之原有控制,将受控参数由4个降低为2个,中间母线电压超调量降低29.8%,并网电流谐波畸变率降低25.3%,且能简单地应用于实验中。

基于实测载荷的牵引车双腔油箱失效研究

针对某牵引车双腔油箱内部实心隔板结构失效且载荷不易获取、量化等问题,提出了一种基于实测载荷的油箱失效研究方法。使用扫描电镜对样件断口进行观测分析,确定失效模式为疲劳失效;基于燃油的力学特性分析,双腔油箱失效主要原因是由单阻尼挡板提供的晃动阻尼不足,导致实心隔板受到冲击力过大;增加多孔阻尼挡板,可降低行车过程中燃油晃动对实心隔板的冲击力,对油箱进行结构优化;油箱优化前、后关键位置安装了传感器,在试验场进行双腔油箱优化前、后两种状态下实心隔板应变载荷采集,对载荷数据进行幅值、雨流及统计分析,对优化前、后油箱实测载荷进行量化分析,优化后载荷最大幅值下降比例超过60%,表明增加阻尼挡板可显著减小实心隔板受到的冲击载荷;优化后试验场路试未出现油箱失效问题,表明优化后实心隔板应变载荷低于油箱的疲劳极限,提高了油箱实心隔板的疲劳寿命;油箱结构优化后满足安全需求,为产品后续优化和下一代新产品开发提供理论指导和数据依据。

Metal-free two-dimensional phosphorene-based electrocatalyst with covalent P-N heterointerfacial reconstruction for electrolyte-lean lithium-sulfur batteries

The use of lithium-sulfur batteries under high sulfur loading and low electrolyte concentrations is severely restricted by the detrimental shuttling behavior of polysulfides and the sluggish kinetics in redox processes.Two-dimensional(2D)few layered black phosphorus with fully exposed atoms and high sulfur affinity can be potential lithium-sulfur battery electrocatalysts,which,however,have limitations of restricted catalytic activity and poor electrochemical/chemical stability.To resolve these issues,we developed a multifunctional metal-free catalyst by covalently bonding few layered black phosphorus nanosheets with nitrogen-doped carbon-coated multiwalled carbon nanotubes(denoted c-FBP-NC).The experimental characterizations and theoretical calculations show that the formed polarized P-N covalent bonds in c-FBP-NC can efficiently regulate electron transfer from NC to FBP and significantly promote the capture and catalysis of lithium polysulfides,thus alleviating the shuttle effect.Meanwhile,the robust 1D-2D interwoven structure with large surface area and high porosity allows strong physical confinement and fast mass transfer.Impressively,with c-FBP-NC as the sulfur host,the battery shows a high areal capacity of 7.69 mAh cm^(−2) under high sulfur loading of 8.74 mg cm^(−2) and a low electrolyte/sulfur ratio of 5.7μL mg^(−1).Moreover,the assembled pouch cell with sulfur loading of 4 mg cm^(−2) and an electrolyte/sulfur ratio of 3.5μL mg^(−1) shows good rate capability and outstanding cyclability.This work proposes an interfacial and electronic structure engineering strategy for fast and durable sulfur electrochemistry,demonstrating great potential in lithium-sulfur batteries.

新型电力系统中异质调频机组分布式协同AGC方法研究

“双碳”目标的实施加速了新型电力系统发展。然而,新型电力系统的转动惯量和调节能力逐渐难以适应复杂多变的负荷变化。因此,开发更高效、更快速的调频资源参与自动发电控制(automatic generation control,AGC)已成为刻不容缓之事。但是,不同调频机组之间的异质性显著,包括机组模型、容量和响应速度的差异,这对AGC提出了挑战。为了提升异质调频资源参与AGC的性能,该文提出了一种分布式协同AGC方法。首先,基于分布式固定时间一致性理论提出了一种分布式固定时间区域控制偏差(area control error,ACE)发掘算法。随后,各AGC机组根据获取的ACE信息设计独立的PI控制器参与频率调节。在ACE调节的最后阶段,根据各机组出力的标幺值,设计了分布式固定时间功率均分控制器,控制低速AGC机组承担更多的功率调整量,从而释放高速AGC机组的容量并为下一轮AGC服务做好准备。通过对包含5种不同调频单元的两区域电力系统进行仿真研究,验证了所提分布式协同AGC方法的性能。结果表明,所提方法可以有效地提高系统的调频性能,且能够在设计的时间内实现期望的有功功率分配。