SiNx：H films with different N/Si ratios are synthesized by plasma-enhanced chemical vapor deposition （PECVD）. Composition and structure characteristics are detected by Fourier transform infrared spectroscopy （FTIR...SiNx：H films with different N/Si ratios are synthesized by plasma-enhanced chemical vapor deposition （PECVD）. Composition and structure characteristics are detected by Fourier transform infrared spectroscopy （FTIR） and X-ray photoelectron spectroscopy （XPS）. It indicates that Si-N bonds increase with increased NH3/SiH4 ratio. Electrical property investigations by I-V measurements show that the prepared films offer higher resistivity and less leakage current with increased N/Si ratio and exhibit entirely insulating properties when N/Si ratio reaches 0.9, which is ascribed to increased Si-N bonds achieved.展开更多
The construction of grouting butt joints of bamboo tubes is simple and efficient.However,when the joint is bent,the low tensile strength of the mortar easily leads to cracking of the mortar prior to the failure of the...The construction of grouting butt joints of bamboo tubes is simple and efficient.However,when the joint is bent,the low tensile strength of the mortar easily leads to cracking of the mortar prior to the failure of the bamboo tube.In this paper,a comparative test of the bending capacity was performed on grouting butt joints reinforced by nonperforated,fully perforated,and semiperforated steel plates embedded in bamboo tubes to obtain the loaddisplacement curves and ultimate bearing capacity of various specimens.The strengthening effect of CFRP pasted on bamboo tubes was also studied.The results show that the opening at the end of the steel plate is beneficial to resist the slip between the mortar and steel plate,while the complete section in the middle of the steel plate is conducive to making full use of the tensile strength of the steel plate.Therefore,it is best to insert the semiperforated steel plate with openings in the end and without openings in the middle into the mortar to enhance the bending properties of the grouting butt joint,which can make the failure mode of the joint change from brittle failure of mortar to ductile compression failure of bamboo tube.In addition,pasting CFRP sheets on the external wall of the bamboo tube helps to reduce the tensile stress of the mortar,while increasing the width of the steel plate can increase the bending moment of inertia of the mixture of the steel plate and mortar.These two complementary measures are very effective in delaying the cracking of the bamboo tube and improving the bending capacity of the joint.展开更多
We investigate the sensitivity of the angular rotation measurement with the method of homodyne detection in SU(2) and SU(1,1) interferometers by employing orbital angular momentum(OAM). By combining a coherent beam wi...We investigate the sensitivity of the angular rotation measurement with the method of homodyne detection in SU(2) and SU(1,1) interferometers by employing orbital angular momentum(OAM). By combining a coherent beam with a vacuum beam in an SU(2) interferometer, we get the sensitivity of the angular rotation measurement as 1/(2N^(1/2)l). We can surpass the limit of the angular rotation measurement in an SU(1,1) interferometer by combining a coherent beam with a vacuum beam or a squeezed vacuum beam when the probe beam has OAM. Without injection, the sensitivity can reach 1/(2N^(1/2)l). In addition, by employing another construction of an SU(1,1) interferometer where the pump beam has OAM, with the same injection of an SU(1,1) interferometer, the sensitivity of the angular rotation measurement can be improved by a factor of 2, reaching 1/(4Nl). The results confirm the potential of this technology for precision measurements in angular rotation measurements.展开更多
文摘SiNx：H films with different N/Si ratios are synthesized by plasma-enhanced chemical vapor deposition （PECVD）. Composition and structure characteristics are detected by Fourier transform infrared spectroscopy （FTIR） and X-ray photoelectron spectroscopy （XPS）. It indicates that Si-N bonds increase with increased NH3/SiH4 ratio. Electrical property investigations by I-V measurements show that the prepared films offer higher resistivity and less leakage current with increased N/Si ratio and exhibit entirely insulating properties when N/Si ratio reaches 0.9, which is ascribed to increased Si-N bonds achieved.
基金The authors are grateful for the financial support of the National Key Research and Development Program of China(2017YFC0703500).
文摘The construction of grouting butt joints of bamboo tubes is simple and efficient.However,when the joint is bent,the low tensile strength of the mortar easily leads to cracking of the mortar prior to the failure of the bamboo tube.In this paper,a comparative test of the bending capacity was performed on grouting butt joints reinforced by nonperforated,fully perforated,and semiperforated steel plates embedded in bamboo tubes to obtain the loaddisplacement curves and ultimate bearing capacity of various specimens.The strengthening effect of CFRP pasted on bamboo tubes was also studied.The results show that the opening at the end of the steel plate is beneficial to resist the slip between the mortar and steel plate,while the complete section in the middle of the steel plate is conducive to making full use of the tensile strength of the steel plate.Therefore,it is best to insert the semiperforated steel plate with openings in the end and without openings in the middle into the mortar to enhance the bending properties of the grouting butt joint,which can make the failure mode of the joint change from brittle failure of mortar to ductile compression failure of bamboo tube.In addition,pasting CFRP sheets on the external wall of the bamboo tube helps to reduce the tensile stress of the mortar,while increasing the width of the steel plate can increase the bending moment of inertia of the mixture of the steel plate and mortar.These two complementary measures are very effective in delaying the cracking of the bamboo tube and improving the bending capacity of the joint.
基金National Natural Science Foundation of China(NSFC)(11774286,11374238,11534008,11574247)
文摘We investigate the sensitivity of the angular rotation measurement with the method of homodyne detection in SU(2) and SU(1,1) interferometers by employing orbital angular momentum(OAM). By combining a coherent beam with a vacuum beam in an SU(2) interferometer, we get the sensitivity of the angular rotation measurement as 1/(2N^(1/2)l). We can surpass the limit of the angular rotation measurement in an SU(1,1) interferometer by combining a coherent beam with a vacuum beam or a squeezed vacuum beam when the probe beam has OAM. Without injection, the sensitivity can reach 1/(2N^(1/2)l). In addition, by employing another construction of an SU(1,1) interferometer where the pump beam has OAM, with the same injection of an SU(1,1) interferometer, the sensitivity of the angular rotation measurement can be improved by a factor of 2, reaching 1/(4Nl). The results confirm the potential of this technology for precision measurements in angular rotation measurements.
