Research on Traffic Safety at Tunnel Entrance and Exit

Highway tunnel entrances have a high rate of expressway traffic accidents.In this paper,the reasons for the high incidence of traffic accidents at highway tunnel entrances are analyzed in detail,and corresponding solutions are proposed,hoping to provide some reference to relevant parties.

Entrance and Exit Defects During Coarse Pitch Orbital Drilling of Carbon Fiber Reinforced Plastic Plates

Formation of entrance and exit defects in coarse pitch orbital drilling(CPOD)of carbon fiber reinforced plastic(CFRP)plates was investigated.Deep observation on entrance and exit morphology shows tear and burr are typical defects.Meanwhile,tear is more obvious than burr,and more entrance tears emerge than exit tears.As one of the major causes of entrance and exit defects in CPOD,cutting forces were substaintially studied by contrast experiments.Then,the effect of cutting parameters on entrance and exit tear was qualitatively analyzed through a single factor test.Experiment results indicate that the variation of rotation speed has little influence on entrance and exit tear.Increasing tangential feed per tooth can enlarge entrance tear,but bring little effect on exit tear.By increasing axial feed pitch,the hole entrance and exit show severe tear.When revolution radius grows bigger and bigger,entrance and exit tear firstly decreases,and then increases.Finally,the models of tear and delamination during CPOD of CFRP were established,the formation mechanisms of entrance and exit defects were revealed,and the control strategies were accordingly put forward.

Detection of keyhole entrance and exit in plasma arc welding

Sensing of keyhole shape and size is important for controlling of plasma arc welding process. In this study, a synchronous vision system is developed by using two CCD cameras to observe the keyhole entrance and exit simultaneously. Experiments are conducted on stainless steel workpiece, Whole keyhole exit image and part of keyhole entrance image are captured synchronously under different welding conditions. Image processing and calibration algorithms are proposed. The boundary and front point of the keyhole entrance and exit are extracted respectively. The effects of welding current and welding speed on ,front point of keyhole entrance and exit are analyzed. Compared to the front point of the keyhole entrance, the position of the front point of the keyhole exit is better to reflect the variation of the welding parameters.

Capacity models on expressway near a bus bay stop with an access

To determinate the expressway capacity near a bus bay stop with an access, capacity models on the expressway near a bus stop with an access were developed on the basis of gap acceptance theory and queuing theory. Depending on a bus stop position to an entrance or an exit ramp, the capacity models were developed for four cases. Bus bay stops with overflow and bus bay stops without overflow were considered. A comparison of simulation experiment and model calculation was carried out. Results show that the suggested models have high accuracy and reliability, at bus arrival rate below 60 vehicles per hour(veh/h) or vehicle volumes at the entrance and the exit below 200 passenger cars units per hour(pcu/h), and there are no significant difference in the capacities for four cases. When bus arrival rate is above 240 veh/h, the capacities of all four cases will decline rapidly. With berth number increasing, the increasing of the capacities is no obvious for four cases. As the bus arrival rate and vehicle volumes at the entrance and the exit increase, bus stops located downstream of an entrance and upstream of an exit have a remarkably effect on the capacities. The latter case is much heavier than the former. Those results can be used to traffic design and optimization on urban expressway near a bus stop with an access.

Construction of a refined population analysis unit based on urban forms and population aggregation patterns

The population analysis unit(PAU)is the basic unit employed in studies of urban populations.The commonly used PAUs are mostly administrative divisions,regular geographic grids.However,these units are different from urban forms,and cannot be used to consider the characteristics of population distributions and flow changes.In this study,we proposed a method for constructing a fine population analysis zone(FPAZ)based on the population aggregation pattern and urban form elements.First,considering the spatial structure of a city and the fine-grained demands of population analysis,the basic analysis unit was divided according to the functional heterogeneity of the population activity region at the micro-scale by combining urban form elements.Next,a population aggregation preference model was established by considering the spatial distribution characteristics of the local aggregation of the urban population flow and long-term stability characteristics depending on the dynamic changes in entrances and exits.Finally,we divided the FPAZ combined with the microstructural elements.Experimental results showed that compared with other types of PAUs,the FPAZ was more consistent with the urban morphology and was an appropriate and general spatial unit for expressing the accurate characteristics of population distributions and changes at the micro-scale.