Experimental investigation on coal pore-fracture variation and fractal characteristics synergistically affected by solvents for improving clean gas extraction

Chemical solvents instead of pure water being as hydraulic fracturing fluid could effectively increase permeability and improve clean methane extraction efficiency.However,pore-fracture variation features of lean coal synergistically affected by solvents have not been fully understood.Ultrasonic testing,nuclear magnetic resonance analysis,liquid phase mass spectrometry was adopted to comprehensively analyze pore-fracture change characteristics of lean coal treated by combined solvent(NMP and CS_(2)).Meanwhile,quantitative characterization of above changing properties was conducted using geometric fractal theory.Relationship model between permeability,fractal dimension and porosity were established.Results indicate that the end face fractures of coal are well developed after CS2and combined solvent treatments,of which,end face box-counting fractal dimensions range from 1.1227 to 1.4767.Maximum decreases in ultrasonic longitudinal wave velocity of coal affected by NMP,CS_(2)and combined solvent are 2.700%,20.521%,22.454%,respectively.Solvent treatments could lead to increasing amount of both mesopores and macropores.Decrease ratio of fractal dimension Dsis 0.259%–2.159%,while permeability increases ratio of NMR ranges from 0.1904 to 6.4486.Meanwhile,combined solvent could dissolve coal polar and non-polar small molecules and expand flow space.Results could provide reference for solvent selection and parameter optimization of permeability-enhancement technology.

Insight into the experiment and extraction mechanism for separating carbazole from anthracene oil with quaternary ammonium-based deep eutectic solvents

Carbazole is an irreplaceable basic organic chemical raw material and intermediate in industry.The separation of carbazole from anthracene oil by environmental benign solvents is important but still a challenge in chemical engineering.Deep eutectic solvents (DESs) as a sustainable green separation solvent have been proposed for the separation of carbazole from model anthracene oil.In this research,three quaternary ammonium-based DESs were prepared using ethylene glycol (EG) as hydrogen bond donor and tetrabutylammonium chloride (TBAC),tetrabutylammonium bromide or choline chloride as hydrogen bond acceptors.To explore their extraction performance of carbazole,the conductor-like screening model for real solvents (COSMO-RS) model was used to predict the activity coefficient at infinite dilution (γ^(∞)) of carbazole in DESs,and the result indicated TBAC:EG (1:2) had the stronger extraction ability for carbazole due to the higher capacity at infinite dilution (C^(∞)) value.Then,the separation performance of these three DESs was evaluated by experiments,and the experimental results were in good agreement with the COSMO-RS prediction results.The TBAC:EG (1:2) was determined as the most promising solvent.Additionally,the extraction conditions of TBAC:EG (1:2) were optimized,and the extraction efficiency,distribution coefficient and selectivity of carbazole could reach up to 85.74%,30.18 and 66.10%,respectively.Moreover,the TBAC:EG (1:2) could be recycled by using environmentally friendly water as antisolvent.In addition,the separation performance of TBAC:EG (1:2) was also evaluated by real crude anthracene,the carbazole was obtained with purity and yield of 85.32%,60.27%,respectively.Lastly,the extraction mechanism was elucidated byσ-profiles and interaction energy analysis.Theoretical calculation results showed that the main driving force for the extraction process was the hydrogen bonding ((N–H...Cl) and van der Waals interactions (C–H...O and C–H...π),which corresponding to the blue and green isosurfaces in IGMH analysis.This work presented a novel method for separating carbazole from crude anthracene oil,and will provide an important reference for the separation of other high value-added products from coal tar.

Research Progress of Deep Eutectic Solvents in Extraction of Plant Flavonoids

As a new type of green solvents,deep eutectic solvents(DESs)have the advantages of strong extraction ability,designability,simple preparation,low price,recoverability and biodegradation,and show great application potential in the field of plant flavonoid extraction.In this paper,the definition,classification and preparation methods of DESs were introduced.The effects of DES composition,molar ratio of DES components,water content of DES systems,liquid-material ratio,extraction temperature,extraction time and extraction auxiliary techniques on the extraction yield of plant flavonoids were expounded.The recycling methods of DESs were summarized.Existing problems of DESs in the field of plant flavonoids extraction were pointed out,and further research direction and trend were analyzed and prospected.

Study on the green extraction of corncob xylan by deep eutectic solvent

Corn as one of the world's major food crops,its by-product corn cob is also rich in resources.However,the unreasonable utilization of corn cob often causes the environmental pollution,waste of resources and other problems.As one of the most abundant polymers in nature,xylan is widely used in food,medicine,materials and other fields.Corn cob is rich in xylan,which is an ideal raw material for extracting xylan.However,the intractable lignin is covalently linked to xylan,which increases the difficulty of xylan extraction.It has been reported that the deep eutectic solvent(DES)could preferentially dissolve lignin in biomass,thereby dissolving the xylan.Then,the xylan in the extract was separated by ethanol precipitation method.The xylan precipitate was obtained after centrifugation,while the supernatant was retained.The components of the supernatant after ethanol precipitation were separated by the rotary evaporator.The ethanol,water and DES were collected for the subsequent extraction of corn cob xylan.In this study,a novel way was provided for the green production of corn cob xylan.The DES was used to extract xylan from corn cob which was used as the raw material.The effects of solid-liquid ratio,reaction time,reaction temperature and water content of DES on the extraction rate of corn cob xylan were investigated by the single factor test.Furthermore,the orthogonal test was designed to optimize the xylan extraction process.The structure of corn cob xylan was analyzed and verified.The results showed that the optimum extraction conditions of corn cob xylan were as follows:the ratio of corn cob to DES was 1:15(g:mL),the extraction time was 3 h,the extraction temperature was 60℃,and the water content of DES was 70%.Under these conditions,the extraction rate of xylan was 16.46%.The extracted corn cob xylan was distinctive triple helix of polysaccharide,which was similar to the structure of commercially available xylan.Xylan was effectively and workably extracted from corn cob by the DES method.This study provided a new approach for high value conversion of corn cob and the clean production of xylan.

The use of environmentally sustainable bio-derived solvents in solvent extraction applications——A review

Replacement of volatile organic compounds （VOCs） by greener or more environmentally sustainable solvents is becoming increasingly important due to the increasing health and environmental concerns as well as economic pressures associated with VOCs. Solvents that are derived from biomass, namely bio-derived solvents, are a type of green solvent that have attracted intensive investigations in recent years because of their advantages over con- ventional VOCs, such as low toxicity, biodegradability and renewability. This review aims to summarize the use of bio-derived solvents in solvent extraction applications, with special emphasis given to utilization of biodiesels and terpenes. Compared with the conventional VOCs, the overall performance of these bio-derived solvents is comparable in terms of extraction yields and selectivity for natural product extraction and no difference was found for metal extraction. To date most researchers have focused on laboratory scale thermodynamics studies. Future work is required to develop and test new bio-derived solvents and understand the kinetic performance as well as solvent extraction nilnt nlant studies.

Efficient Extraction of Astaxanthin from Phaffia rhodozyma with Polar and Non-polar Solvents after Acid Washing

method of extracting astaxanthin from Phaffia rhodozyma with various solvents after acid washing was investigated. The extraction efficiency was distinctly increased after acid washing of P. rhodozyma cells. When the concentration of HCl was 0.4 mol.L^-1, the highest extraction efficiency of astaxanthin was achieved which was about three times higher than the control. Acetone or benzene as single polar or non-polar solvent was the most ef- fective solvent in our research. With a combination of isopropanol and n-hexane （volume ratio of 2 ： 1）, the maxi- mal extraction efficiency was achieved, approximately 60% higher than that obtained with a single solvent. The liquid-solid ratio and the extracting time were also optimized. Under the optimum extraction conditions, the extraction yield of astaxanthin exceeded 98%.

Comparison of Extraction Techniques with Different Solvents for DDT Analogues in Sediments

Four techniques, Soxhlet extraction (SOX), ultrasonic extraction (USE), fluidized-bed extraction (FBE) and acce-lerated solvent extraction (ASE) with different solvents (methanol, hexane/acetone and acetonitrile) were used for theextraction of DDT analogues in sediments. Results revealed that the four extraction techniques had high recoveries (>86.0%) with low standard deviations (< 12.0%) for most of DDT analogues, meaning that they could all successfully extractDDT analogues in sediments. Accelerated solvent extraction using methanol and hexane/acetone (1:1), fluidized-bedextraction using hexane/acetone (1:1) and the ultrasonic extraction using hexane/acetone (1:1) were comparable or betterthan Soxhlet extraction using hexane/acetone (1:1). Considering solvent- and time-consumption, level of automation,and environmental risk, accelerated solvent extraction with hexane/acetone (1:1) was better than the other extractiontechniques.

Deep eutectic solvents and alkaline extraction of protein from seabuckthorn seed meal: a comparison study

Seabuckthorn seed meal(SSM) is a waste of oil extraction industry that rich in protein. In order to seek suitable protein extraction method, three different deep eutectic solvents(DESs)(including choline chlorideglycerol, choline chloride-oxalic acid and choline chloride-urea) were developed for extracting protein from SSM and compared with alkaline. Result indicated that alkaline could effectively extract 56.9% protein from SSM and its protein content was 73.1%, higher than DES at 31.0%-41.4% and 64.3%-67.5%, respectively. However, compared to alkali, DES led to a product with less β-sheet, more β-turn, more essential amino acids, higher total amino acid content, especially choline chloride-urea which extracted protein showing an integrated and similar protein weight distribution compared to SSM. Also, this protein extracted chloride-urea showed a highest digestibility in vitro(by pepsin)(54.2%). These results indicated that choline chloride-urea extraction is better than alkaline extraction for SSM.

Improved Production of Paclitaxel from Suspension Culture of Taxus chinensis var. mairei by in situ Extraction with Organic Solvents

The production of paclitaxel from suspension culture of Taxus chinensis var,mairei was improved by in situ extraction with organic solvents to avoid feedback repression and product degradation.Oleic acid and dibutyl phthalate were proved to be suitable solvents .The optimal volumetric percentage of organic solvents in the culture medium was found to be around 8%,and the favorable time for their introduction was at the exponential phase of cell growth,Paclitaxel production with the in situ extraction was ca 3-fold of that without extraction.

Long-chain alkanol-alkyl carboxylic acid-based low-viscosity hydrophobic deep eutectic solvents for one-pot extraction of anthraquinones from Rhei Radix et Rhizoma

Natural long-chain alkanol and alkyl carboxylic acid were used to prepare novel hydrophobic deep eutectic solvents(HDESs).These HDESs are liquid at room temperature and have low viscosity(<12.26 mPa·s),low polarity(lower than that of methanol,ChCl-based deep eutectic solvents and other reported HDESs),and low density(<0.928 g/mL).A simple one-pot method based on a novel HDES-water two-phase extraction system was constructed for the extraction of weak-polarity bioactive components,anthraquinones,from Rhei Radix et Rhizoma.This HDES-based new extraction method does not consume hazardous organic solvents and can obtain a total anthraquinone yield of 21.52 mg/g,which is close to that obtained by the Chinese pharmacopoeia method(21.22 mg/g)and considerably higher than those by other reported HDESs-based extraction methods(14.20-20.09 mg/g,p<0.01).The high extraction yield can be mainly attributed to the severe destruction of the RRR cell walls by the extraction system and the excellent dissolving ability of novel HDESs for anthraquinones.

Efficient and selective extraction of sinomenine by deep eutectic solvents

Sinomenine is the main bio-active ingredient of Sinomenii Caulis and usually produced by solventextraction techniques. However, the extraction of sinomenine suffers from the lack of highly efficient and environmentally-benign solvents. In this work, deep eutectic solvents(DESs) based on fragrances were synthesized, hydrogen-bond donors(HBDs) and hydrogen-bond acceptors(HBAs) components of DESs were identified and their extraction ability for sinomenine was evaluated and the extraction conditions were optimized by single-factor and orthogonal design experiments. It was found that the hydrogen-bonding interaction between sinomenine and DESs was the main extraction driving force and there was no explicit relationship between the extraction ability and the hydrophobicity of the DESs. The DESs could be recycled and sinomenine could be recovered quantitatively via backextraction. High-purity sinomenine((95.0 ± 2.3)%) could be produced. These findings suggest that DESs are highly-effective solvents for the isolation of sinomenine and exhibit great potential for the extraction of other bio-active compounds.

Effect of Different Solvents on the Extraction of Phytochemicals in Colored Potatoes

Colored potatoes are an interesting alternative to the traditional, white-creamed potatoes, due to their high phytochemical content, which have been proved to have antioxidative properties. The extraction of polyphenols is highly dependent on using the appropriate solvent systems. Therefore, polyphenol extraction in colored potatoes [Vermillion Fingerling (VF);Jester Potato (JP);Magic Molly (MM);Blue Belle (BB);All Blue (AB)] using different solvents [Solvent A (24% water, 67% ethanol 9% acetic acid);Solvent B (5% acetic acid);and Solvent C (95% water, 5% acetic acid, 0.5 g sodium bisulfate)] may have significant effects on extraction efficiency and phytochemical content. Total phenolic content (TPC), Total flavonoid content (TFC), Total anthocyanin content (TAC) and antioxidant activities [Trolox Equivalent Antioxidant Capacity (TEAC) and Ferric reducing-antioxidant power (FRAP)] were determined. Solvent A extracted significantly (p < 0.05) higher TPC from BB (13.93 mg GAE/100g) compared to the other solvents. VF and JP displayed higher TFC (14.53 and 19.46 mg CE/100g, respectively) when Solvent C was utilized. VF and JP extracts with Solvent C displayed the highest FRAP value compared to Solvent B. MM displayed the highest TAC using Solvent A and C. Potato variety resulted in high variability in polyphenols content and antioxidant activity. The utilization of colored potatoes or extracts in the food industry could provide innovative products and a functional alternative to the traditional.

Extraction and Characterization of Oil from <i>Moringa oleifera</i>Using Supercritical CO₂and Traditional Solvents

The present work presents a first characterization of the oil from the Moringa (Moringa oleifera) kernel as a potential candidate for biodiesel production. Moringa is an indigenous tree in the Yucatan Peninsula in Mexico, where there is a nascent biodiesel industry. Several extraction methods are compared in terms of the extraction yields, including solvent extraction (n-hexane and ethanol), and supercritical extraction (Sc-CO2). The results are also compared against previ- ously reported data. For supercritical extraction pressures of 200 to 400 bar and temperatures of 40℃ and 60℃ were tested. Gas Chromatography analysis reveals that the main fatty acids in Moringa oil are oleic acid (69%), palmitic acid (10%), and stearic acid (8%).

A Comparison Study of Phenolic Contents and <i>in Vitro</i>Antioxidant Activities of Australian Grown Faba Beans (<i>Vicia faba</i>L.) Varying in Seed Coat Colours as Affected by Extraction Solvents

Twelve Australian grown faba bean genotypes with seed colour ranging from white, different shades of buff/beige, green, red and purple, were extracted using 80% methanol (v/v) or 70% acetone (v/v). The findings showed that commonly consumed buff-coloured genotypes have comparable phenolic contents and antioxidant activities to those with exotic seed coat colour (red, green and purple). In general, the extraction yield for methanol and acetone extracts of faba bean genotypes were similar. However, the acetone extracts of faba bean varieties with coloured seed coats exhibited higher antioxidant activities than their methanol extracts counterparts. Phenolic compounds and antioxidant activities of the genotypes were compared in an array of chemical-based assays and profiled using an on-line high-performance liquid chromatography-post column derivatization (HPLC-PCD) system. The total phenolic content (TPC) and total flavonoid content (TFC) of acetone extracts were approximately twice those of methanol extracts. The acetone extracts contained six times higher levels of di(phenyl)-(2,4,6-trinitrophenyl) imi- noazanium radical scavenging activity (DPPH), six times higher Total Equivalent Antioxidant Capacity (TEAC) and two times higher Ferric Reducing Antioxidant Power (FRAP) than those of methanol extracts. In general, the methanol extracts of white-coloured faba bean genotype exhibited comparable phenolic contents and antioxidant activities to varieties with coloured seed coats. However, the TPC, TFC, DPPH, TEAC and FRAP of acetone extracts from white-coloured genotype were 2 - 4, 1 - 2, 5 - 9, 2 - 3 and 1 - 2 times lower than those of faba bean varieties with coloured seed coats. HPLC-PCD analyses showed substantial antioxidant responses, represented as a dense “hump” of peaks in the HPLC chromatograms of acetone extracts from coloured-genotypes. This “hump” was not detected in the chromatograms of white-genotype acetone extracts, or in chromatograms of methanol extracts regardless of genotype or seed coat colour. All coloured-beans had higher phenolic contents and antioxidant activities than the white-genotype. Hydroxybenzoic acids/flavanols, hydroxycinnamic acids and flavonols were dominant in coloured beans. The findings suggest potentials in selecting commonly consumed buff-coloured faba bean genotypes within the breeding programs for enhanced levels of phenolic compounds and antioxidant activities, potentially increasing their health-promoting properties. And, there might also be potentials in developing faba bean extracts for pharmaceutical or natural medicines.

Cu(II) Extraction in Ionic Liquids and Chlorinated Solvents: Temperature Effect

Room temperature ionic liquids have been currently used in liquid/liquid extraction processes in order to substitute conventional organic solvents. In this paper, a series of chlorinated solvents and 1-alkyl-3-me- thylimidazolium-based ionic liquids were selected to study the extraction efficiency of a lipophilic polya- mine 1,1,7,7-tetraethyl-4-tetradecyldiethylenetriamine (TE14DT) towards the model ion Cu(II) in such dif-ferent media. The effect of temperature on the extraction efficiency was also investigated. The metal ion par-tition was found to be strongly dependent on both the nature of the solvent and on the working temperature. The viscosity of ionic liquids and the water content in ionic liquid were found to affect the extraction effi-ciency of TE14DT. The chemical nature of the cation of ionic liquids, and in particular the alkyl chain length on imidazolium ring, also seemed to be important in determining the efficiency of the extraction process. Finally, preliminary experiments on back-extraction of Cu(II) ions from ionic liquid also revealed interesting hints to the development of a continuous transport process.

Selection of Extraction Solvents for Bitumen from Indonesian Oil Sands through Solubility Parameters

Indonesian oil sands were systematically separated to investigate their basic composition.The extraction effects of the solvents with different Hilderbrand solubility parameters(HSPs)on the bitumen of Indonesian oil sands were compared.Furthermore,the Hansen solubility combination parameter(HSCP)and Teas triangle were used to explore rules in the separation of oil sands bitumen via solvent extraction.Finally,the saturates,aromatics,resins,and asphaltenes(SARA)fractions of the bitumen from Indonesian oil sands were analyzed.The results showed that the Indonesian oil sands were oil-wet with a bitumen content of 24.93%.The solvent extraction for bitumen could be accurately and conveniently selected based on the solubility parameter.When the HSPs of the extraction solvent were around 18–19 and the HSCPs were closer to a certain range(δ_(d)=17.5–18.0,δ_(p)=1–3.5,and δ_(h)=2–6),the extraction effect of bitumen from Indonesian oil sands improved,and the primary component affecting the extraction rate of bitumen were asphaltenes.

Effect of Temperature on Extraction of Castor Oil from Castor Seeds Using Potential Green Solvents

Extraction of castor oil from castor seeds was investigated using different green solvents which include d-limonene, p-cymene, α-pinene, ethanol, and furfural at the temperature range of (323 - 413) K. The Soxhlet extraction method was employed to investigate the effect of temperature at atmospheric pressure. The focus of the study was to investigate a potential green solvent that can produce the high yields compared to the traditional solvent (hexane). The results show that at the average time of 3 hours and 30 minutes, the castor oil yield for green solvents were ranked as furfural (47.13%) > ethanol (45.37%) > p-cymene (39.15%) > d-limonene (39.13%) > α-pinene (38.11%). These castor oil yields were obtained at optimum temperatures for each green solvent. The castor oil yields were compared to the yield of hexane (31.36%) at same average time. The green solvents were recovered by using simple distillation, except furfural which was difficult to be recovered.

Influence of solvents on extraction of U(VI)by N,N’-didecanoylpiperazine

Extraction behavior of N,N'-didecanoylpiperazine(DDPEZ)for U(VI) in a series of solvents from aqueous nitric acid media was investigated for the first time.The dependence of distribution ratios on the concentration of aqueous nitric acid,extractant and temperature has been discussed.The increasing sequence of extractive ability of DDPEZ is given:chloroform,carbon tetrachloride,dimethylbenzene,toluene,benzene.

Study on Extraction of Tea Saponin from Camellia oleifera Cake Using Water as Extraction Solvent

This paper studied the effects of liquid-solid ratio, temperature, time and pH value on the extraction rate of tea saponin from the cake of Camellia oleifera seeds by using single factor experiment with the cake of Camellia oleifera seeds as the raw materials, and water as the extraction solvent, and orthogonal test was used to determine the optimal extraction process conditions. The results showed that the extraction ratio of tea saponin could reach up to 95.50% when the liquidsolid ratio was 11：1, extracting temperature of 80 ℃, extraction time of 6 h, and pH value of 9.

Removal of chromium(Ⅲ) from aqueous waste solution by predispersed solvent extraction

The extraction experiments of chromium（W） from aqueous waste solution by predispersed solvent extraction （PDSE） process with extractant （HEHPEHE） and its mixture, including acidic extractant （D2EHPA）, alkaline extractant （TOA） and neutral extractant （TBP） were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium（III） from aqueous waste solution. The colloidal liquid aphrons （CLAs） were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate （SDBS） as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate （Tween-20） in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium（III）, the effects of major factors, such as initial chromium（III） concentration, volume of colloidal gas aphrons （CGAs）, HEHPEHE volume fraction, phase ratio （solvent phase to water phase）, mass fraction of dodecyl trimethylammonium bromide （HTAB）, mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium（III） above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.