Preparation and Application of the Hydrophilic Amino-Silicone Softener by Emulsion Polymerization

The amino poly-siloxane was modified with self-made polyether silicones by the crafts of emulsion polymerization. We studied the emulsifier, the dosage of emulsifier initiator, polyether/silane coupling agent, pH value. There are some results of the research indicated in the following. First, there are many factors for the hydrophilic amino-silicone softener both on the polymerization process and the performance, such as the proportion and amount of emulsifier, initiator dosage, the mass ratio of the polyether and hydrogen silicone oil, the choice of silicone coupling agent, and the ratio and dosage of polyether silicones silane coupling agent. Second, the amount of hydrogen of the hydrogen silicones and the choice of catalyst are the key points on the synthesis of polyether silicones. The amount of hydrogen should be low and the catalyst must be economical and efficient and its introduction should be small and times, other more the holding time is not too long. The next one is that, in the process of hydrolysis of silane coupling agent, we need some acid to adjust pH value, or they will be broken down. The most important one but not the last is that the epoxy group can improve the products low-temperature supple and the persistence of the finishing fabric, furthermore it can reduce yellowing and has a good stability of the inorganic salt, however, it will be destroyed if the reaction temperature for epoxy is too high. What’s more, it is very economical and environmental that the process of emulsion is simple and with less emulsifier.

Observation of a Chemical Softener’s Effects on Stem-Specific Lignocellulosic <i>Brassica napus</i>(Type: Canola) (Cultivar: HYHEAR 3) Fiber Quality

Chemical softener (Cepreton UN) is used to soften the cellulosic fiber (cotton) in the textile industries to make clothes better to touch. Therefore, this study investigated the effects of Cepreton UN on both physical (length, aspect ratio, contact angle, and moisture regain) and mechanical (load at break, elongation at break, tensile stress, young’s modulus, and tenacity) properties of the lignocellulosic canola (HYREAR 3) fibers extracted from narrow, medium, and wide stems. ANOVA showed that fiber diameter had strong effects on elongation at break, load at break, tensile stress, young’s modulus, and aspect ratio for all fibers. Corrgram values showed that tensile stress, young’s modulus, and aspect ratio were negatively correlated to fiber diameter whereas load at break and tenacity were mostly positively correlated to fiber diameter. The fibers were treated with 2% and 10% Cepreton UN and compared with control fibers. In most cases, the fiber diameter was decreased in both 2% and 10% treated medium stem fibers. The mean values of elongation at break, load at break, tenacity, and contact angle were decreased for 10% and increased for 2% and the mean values of tensile stress, young’s modulus, and aspect ratio were decreased for 2% and increased for 10% treated medium stem fibers. Moisture regain (%) mostly decreased for 2%, and increased for 10% treated fibers. Low pH (4.5) had an almost similar effect on fibers as 2% Cepreton UN. Overall, 2% Cepreton UN treatment is found to be better than 10% to make canola fibers less stiff and low pH was found to be an alternative softener treatment strategy.

A vector sum analysis method for stability evolution of expansive soil slope considering shear zone damage softening

Slope stability analysis is a classical mechanical problem in geotechnical engineering and engineering geology.It is of great significance to study the stability evolution of expansive soil slopes for engineering construction in expansive soil areas.Most of the existing studies evaluate the slope stability by analyzing the limit equilibrium state of the slope,and the analysis method for the stability evolution considering the damage softening of the shear zone is lacking.In this study,the large deformation shear mechanical behavior of expansive soil was investigated by ring shear test.The damage softening characteristic of expansive soil in the shear zone was analyzed,and a shear damage model reflecting the damage softening behavior of expansive soil was derived based on the damage theory.Finally,by skillfully combining the vector sum method and the shear damage model,an analysis method for the stability evolution of the expansive soil slope considering the shear zone damage softening was proposed.The results show that the shear zone subjected to large displacement shear deformation exhibits an obvious damage softening phenomenon.The damage variable equation based on the logistic function can be well used to describe the shear damage characteristics of expansive soil,and the proposed shear damage model is in good agreement with the ring shear test results.The vector sum method considering the damage softening behavior of the shear zone can be well applied to analyze the stability evolution characteristics of the expansive soil slope.The stability factor of the expansive soil slope decreases with the increase of shear displacement,showing an obvious progressive failure behavior.

Alternative splicing of the PECTINESTERASE gene encoding a cell wall-degrading enzyme affects postharvest softening in grape

The firmness of table grape berries is a crucial quality parameter. Despite extensive research on postharvest fruit softening, its precise molecular mechanisms remain elusive. To enhance our comprehension of the underlying molecular factors, we initially identified differentially expressed genes(DEGs) by comparing the transcriptomes of folic acid(FA)-treated and water-treated(CK) berries at different time points. We then analyzed the sequences to detect alternatively spliced(AS) genes associated with postharvest softening. A total of 2,559 DEGs were identified and categorized into four subclusters based on their expression patterns, with subcluster-4 genes exhibiting higher expression in the CK group compared with the FA treatment group. There were 1,045 AS-associated genes specific to FA-treated berries and 1,042 in the CK-treated berries, respectively. Gene Ontology(GO) annotation indicated that the AS-associated genes in CK-treated berries were predominantly enriched in cell wall metabolic processes,particularly cell wall degradation processes. Through a comparison between treatment-associated AS genes and subcluster-4 DEGs, we identified eight genes, including Pectinesterase 2(VvPE2, Vitvi15g00704), which encodes a cell wall-degrading enzyme and was predicted to undergo an A3SS event. The reverse transcription polymerase chain reaction further confirmed the presence of a truncated transcript variant of VvPE2 in the FA-treated berries.Our study provides a comprehensive analysis of AS events in postharvest grape berries using transcriptome sequencing and underscores the pivotal role of VvPE2 during the postharvest storage of grape berries.

Influence of thermomechanical treatment on recrystallization and softening resistance of Cu-6.5Fe-0.3Mg alloy

The recrystallization and softening resistance of a Cu-6.5Fe-0.3Mg(mass fraction,%)alloy prepared by Process 1(cold rolling heat treatment)and Process 2(hot/cold rolling heat treatment)were studied using Vickers hardness tests,tensile tests,scanning electron microscopy and transmission electron microscopy.The softening temperature,hardness and tensile strength of the alloy prepared by Process 2 were 110°C,HV 15 and 114 MPa higher,respectively,than those of the alloy prepared by Process 1 after aging at 300°C.The recrystallization activation energy of the alloys prepared by Process 1 and Process 2 were 72.83 and 98.11 kJ/mol,respectively.The pinning effects of the precipitates of the two alloys on grain boundaries and dislocations were basically the same.The softening mechanism was mainly attributed to the loss of dislocation strengthening.The higher Fe fiber density inhibited the average free migration path of dislocations and grain boundary migration in the alloy,which was the main reason for higher softening temperature of the alloy prepared by Process 2.

Flow softening behavior and microstructure evolution of Al-5Zn-2Mg aluminum alloy during dynamic recovery

The flow stress behavior and microstructure development of Al-5Zn-2Mg （7005） aluminum alloy were studied by hot compression tests at deformation temperatures between 300-500 ＆#176;C and strain rates between 0.05-50 s-1. The deformed structures of the samples were observed by optical microscopy （OM）, transmission electron microscopy （TEM） and electron backscattering diffraction （EBSD） analysis. The calculated activation energy is 147 kJ/mol, which is very close to the activation energy for lattice self-diffusion in aluminum （142 kJ/mol）. Dynamic recovery is the dominant restoration mechanism during the deformation. At high strain rate of 50 s-1, temperature rise due to deformation heating leads to a significant flow softening. Microstructure observations indicated that the remaining softening after deformation heating correction at high strain rate and the softening observed at high temperature are associated with grain coarsening induced by grain boundary migration during dynamic recovery process.

Effect of strain rate and deformation temperature on strain hardening and softening behavior of pure copper

The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystallization critical stress, saturated stress, dynamic recovery volume fraction and dynamic recrystallization volume fraction were determined. According to the processing map, the instability regions occur in regions of 400?450 °C, 0.001?0.05 s?1 and 450?750 °C, 0.05?1 s?1. The deformation mechanism in the stability region is dynamic recrystallization. The flow stress was predicted. The results also show that the true stress–true strain curves predicted by the extracted model are in good agreement with the experimental results.

FEM modeling of softened base metal in narrow-gap joint by CMT+P MIX welding procedure

A required finite element method（FEM） model applicable for narrow gap CMT and CMT＋P MIX welding was established based on the interactions between arc,base metal and filler metal.A novel method of simplifying wire feeding pulses and heat input pulses was supposed under the conduction of equivalent input.The method together with composed double-ellipse heat sources was included in the model.The model was employed in the investigation of thermal cycling and the identification of the softened zone of AA7A52 base plates.Low-frequency behavior emerged in the form of low-cooling rate sects,which were not expected under experimental conditions.The softened zone including the quenched zone and averaging zone of the base plate was much wider internal the base plate than that close to the surfaces.The reliability of the predictions in thermal cycling was supported by infrared imaging test results of the thermal cycle process.

Effects of Acetylsalicylic Acid (ASA) and Ethylene Treatments onRipening and Softening of Postharvest Kiwifruit

Kiwifruit (Actinidia deliciosa (A. Chev.) C. F. Liang et A. R. Ferguson cv. Bruno) was used toinvestigate the effects of acetylsalicylic acid (ASA, 1.0 mmol/L, pH 3.5) and ethylene (100 mL/L) treat-ments on changes at endogenous salicylic acid (SA) levels and other senescence-related factors duringfruit ripening and softening at 20 ℃. The level of endogenous SA in ripening fruits declined and a closerelationship was observed between the change at endogenous SA level and the rate of fruit ripening andsoftening. ASA treatment elevated SA level in the fruit, slowed down the increases in lipoxygenase (LOX)and allene oxide synthase (AOS) activities, decreased the O22-. production in the preclimacteric phase andthe early phase of ethylene climacteric rise, maintained the stability of cell membrane, inhibited ethylenebiosynthesis, postponed the onset of the ethylene climacteric, and delayed the process of fruit ripeningand softening. On the contrary, application of ethylene to ripening kiwifruit resulted at a lower SA level, anaccelerated increases in the activities of LOX and AOS and the rate of O22-. production, an elevated relativeelectric conductivity and an advanced onset of ethylene climacteric, and a quicker fruit ripening andsoftening. It is suggested that the effects of ASA on ripening kiwifruit can be attributed to its ability toscavenge O22-. and/or to maintain stability of cell membrane.

Effect of MgO content in sinter on the softening–melting behavior of mixed burden made from chromium-bearing vanadium–titanium magnetite

The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.

ELASTO-PLASTIC CONSTITUTIVE MODEL OF SOIL-STRUCTURE INTERFACE IN CONSIDERATION OF STRAIN SOFTENING AND DILATION

The behavior of soil-structure interface plays a major role in the definition of soil-structure interaction. In this paper a bi-potential surface elasto-plastic model for soil-structure interface is proposed in order to describe the interface deformation behavior,including strain softening and normal dilatancy. The model is formulated in the framework of generalized potential theory,in which the soil-structure interface problem is regard as a two-dimensional mathematical problem in stress field,and plastic state equations are used to replace the traditional field surface. The relation curves of shear stress and tangential strain are fitted by a piecewise function composed by hyperbolic functions and hyperbolic secant functions,while the relation curves of normal strain and tangential strain are fitted by another piecewise function composed by quadratic functions and hyperbolic secant functions. The approach proposed has the advantage of deriving an elastoplastic constitutive matrix without postulating the plastic potential functions and yield surface. Moreover,the mathematical principle is clear,and the entire model parameters can be identified by experimental tests. Finally,the predictions of the model have been compared with experimental results obtained from simple shear tests under normal stresses,and results show the model is reasonable and practical.

Dynamic softening behaviors of 7075 aluminum alloy

The dynamic softening behaviors during hot deformation of 7075 aluminum alloy were studied by isothermal hot compression tested at temperatures of 250, 300, 350, 400 and 450 ℃ and strain rates of 0.01, 0.1, 1 and 10 s-1 on Gleeble1500. The results show that the temperature changes have a significant effect on the dynamic softening rate. It is indicated that the considerable dynamic softening rate associated with dynamic recrystallization leads flow stress value decreasing gradually. A group of coefficients needed by the phenomenological constitutive model containing a softening ratio item were calculated by the multiple linear regression method. The optical microstructures show that the grains of billets compressed become more and more refined with strain rate increasing as well as the degree of dynamic softening and work-hardening higher. The phenomenological constitutive description of 7075 aluminum alloy can accurately describe the relationships among flow stress, temperature, strain rate, strain and dynamic softening, and offer the basic model for plastic forming process simulation.

Strain Softening and Hardening Behavior in AZ61 Magnesium Alloy

The deformation behavior of AZ61 Mg alloy during hot deformation has been investigated in wide temperature and strain rate range by a Gleeble simulator. Specimens are deformed in compression in the temperature range of 523-673 K and at strain rates of 0.001-1 s-1. It is found that the flow curves exhibit a peak and then decrease towards steady-state of classical DRX, which decrease with rising temperature and decreasing strain rate. The deformation behavior of the specimens can be attributed to the occurrence of strain hardening and softening. As stress decreases, the strain hardening rate declines at a fast rate when temperature rises or strain rate decreases. The shapes of θ-σ curves indicate some important features such as subgrain formation, the criticai stress, the peak stress and steady stress. The onset of DRX can be determined by the point of inflection on θ-σ or Inθ-σ curves.

ANALYTICAL SOLUTIONS TO EXPANSION OF CYLINDRICAL CAVITY IN LINEAR SOFTENING SOIL

Based on the results of conventional triaxial compression tests for a soil, a trilinear elasto-plastic model is proposed to simulate the stress-strain softening curve. According to this curve, the constitutive relation between the bulk strain and two principal strains is established. By using Mohr-Coulomb’s yield criterion as the initial yield function with plastic ?ow phases stage and constructing the rational yield function for the strain softening phase stage, the analytical solutions to the stress, strain, and displacement ?elds for the expansion of cylindrical cavity are presented. Finally, a computational example is used to show the radii of di?erent stress zones and the corresponding internal pressure.

EFFECT OF MICROSTRUCTURE ON THE HARDENING AND SOFTENING BEHAVIORS OF POLYCRYSTALLINE SHAPE MEMORY ALLOYS PART Ⅰ:MICROMECHANICS CONSTITUTIVE MODELING

The effects of microstructure and its evolution on the macroscopic superelastic stress-strain response of polycrystalline Shape Memory Alloy(SMA)are studied by a microstructure-based constitutive model developed in this paper.The model is established on the following basis:(1)the transformation conditions of the unconstrained single crystal SMA microdomain(to be distinguished from the bulk single crystal),which serve as the local criterion for the derivation of overall transfor- mation yield conditions of the polycrystal;(2)the micro-to macro-transition scheme by which the connection between the polycrystal aggregates and the single crystal microdomain is established and the macroscopic transformation conditions of the polycrystal SMA are derived;(3)the quantitative incorporation of three microstruc- ture factors(i.e.,nucleation,growth and orientation distribution of martensite)into the modeling.These microstructural factors are intrinsic of specific polycrystal SMA systems and the role of each factor in the macroscopic constitutive response is quan- titatively modeled.It is demonstrated that the interplay of these factors will result in different macroscopic transformation kinematics and kinetics which are responsible for the observed macroscopic stress-strain hardening or softening response,the latter will lead to the localization and propagation of transformation bands in TiNi SMA.

Hydrophilic and strength-softening characteristics of calcareous shale in deep mines

To better understand the mechanism of the strength weakening process of soft rocks in deep mines after interacting with water, a self-developed experimental system, Intelligent Testing System for Water Absorption in Deep Soft Rocks （ITSWADSR）, is employed to analyze the hydrophilic behavior of deep calcareous shale sampled from Daqiang coal mine. Experimental results demonstrate that the relation between water absorption and time can be expressed by power functions, and the soakage rate decreases while the soakage increases with time. In order to quantitatively calculate the weight coefficients of the influential factors for water absorbing capacity of rocks, a series of testing methods are adopted, including scanning electron microscope （SEM）, X-ray diffraction and mercury injection test. It is demonstrated that the effective porosity has a positive correlation with the water absorbing capacity of rocks and the contents of illite and illite/smectite. The initial water content presents a negative correlation with the water absorption capacity of rocks. According to the absolute value of weight coefficients of various influential factors, the order of magnitude from high to low is captured： initial water content, illite, illite/smectite formation （S=5%）, and the effective porosity. After water absorption tests, uniaxial compressive strength （UCS） tests were performed on rock specimens allowing a linear relationship between the UCS and the water content of rock to be established, indicating that the strength of calcareous shale decreases linearly with the increasing water content.

Molecular Cloning and Characterization of Fruit Softening Related Gene β-Mannanase from Banana Fruit

A 1 250 bp cDNA fragment encoding β-mannanase, named MaMAN, was cloned from banana （Musa spp cv. Baxi） fruit using degenerate primers designed with reference to the conserved nucleic acid sequences of known β-mannanase genes by RT-PCR. Sequence analysis showed that MaMAN cDNA encompassed a 1 085 bp open-reading frame （ORF）, encoding a predicted polypeptide of 395 amino acids. Alignment of the deduced amino acid sequence of MaMAN and other putative β-mannanases showed that MaMAN has an identity of 86, 70, 69, 54, and 57%, respectively, to β-mannanases from tomato, lettuce, arabidopsis, carrot and oryza sativa. The catalytic residues： Asn203, Glu204, Glu318 and the active site residues： Arg86, His277, Tyr279, and Trp360, which were strictly conserved in the glycoside hydrolase family 5 to which all β-mannanases belonged, were found in MaMAN. Semi-quantitative RT-PCR revealed that the level of MaMAN transcript in the pulp increased during banana fruit ripening, suggesting that MaMAN was likely to be involved highly in banana fruit softening.

Damage constitutive model for strain-softening rock based on normal distribution and its parameter determination

Firstly, using the damage model for rock based on Lemaitre hypothesis about strain equivalence, a new technique for measuring strength of rock micro-cells by adopting the Mohr-Coulomb criterion was developed, and a statistical damage evolution equation was established based on the property that strength of micro-cells is consistent with normal distribution function, through discussing the characteristics of random distributions for strength of micro-cells, then a statistical damage constitutive model that can simulate the full process of rock strain softening under specific confining pressure was set up. Secondly, a new method to determine the model parameters which can be applied to the situations under different confining pressures was proposed, by deeply studying the relations between the model parameters and characteristic parameters of the full stress-strain curve under different confining pressures. Therefore, a unified statistical damage constitutive model for rock softening which can reflect the effect of different confining pressures was set up. This model makes the physical property of model parameters explicit, contains only conventional mechanical parameters, and leads its application more convenient. Finally, the rationality of this model and its parameters-determining method were identified via comparative analyses between theoretical and experimental curves.

Estimation of compaction grouting pressure in strain softening soils

A new method was proposed to predict the limited compaction grouting pressure for the soft soils. Theoretical basis of the method considered the conical shear failure above the grout bulb. Using the Mohr-Coulomb yield criterion as the initial yield function, the limited compaction grouting pressure was determined, according to the softening elastic-plastic model based on the conventional triaxial compression tests to simulate the strain softening soils. The small strain in the elastic zone and large stain in the plastic zone and the rational yield function for the strain softening phase stage, the analytical solutions to the compaction grouting pressure were presented. The results indicate reasonable agreement and show a good potential of the proposed method for rationally optimizing the design of compaction grouting operations.

A COMBINED PARAMETRIC QUADRATIC PROGRAMMING AND PRECISE INTEGRATION METHOD BASED DYNAMIC ANALYSIS OF ELASTIC-PLASTIC HARDENING/SOFTENING PROBLEMS

The objective of the paper is to develop a new algorithm for numerical solution of dynamic elastic-plastic strain hardening/softening problems. The gradient dependent model is adopted in the numerical model to overcome the result mesh-sensitivity problem in the dynamic strain softening or strain localization analysis. The equations for the dynamic elastic-plastic problems are derived in terms of the parametric variational principle, which is valid for associated, non-associated and strain softening plastic constitutive models in the finite element analysis. The precise integration method, which has been widely used for discretization in time domain of the linear problems, is introduced for the solution of dynamic nonlinear equations. The new algorithm proposed is based on the combination of the parametric quadratic programming method and the precise integration method and has all the advantages in both of the algorithms. Results of numerical examples demonstrate not only the validity, but also the advantages of the algorithm proposed for the numerical solution of nonlinear dynamic problems.