Comparative Analysis of Equal and Unequal Grounding Grid Configurations by Compression Ratio and Least Square Curve Fitting Techniques

The primary aim of the power system grounding is to safeguard the person and satisfying the performance of the power systemtomaintain reliable operation.With equal conductor spacing grounding grid design,the distribution of the current in the grid is not uniform.Hence,unequal grid conductor span in which grid conductors are concentrated more at the periphery is safer to practice than equal spacing.This paper presents the comparative analysis of two novel techniques that create unequal spacing among the grid conductors:the least-square curve fitting technique and the compression ratio techniquewith equal grid configuration for both square and rectangular grids.Particle Swarm Optimization(PSO)is adopted for finding out one optimal feasible solution among many feasible solutions of equal grid configuration for both square and rectangular grids.Comparative analysis is also carried out between square and rectangular grids using the least square curve fitting technique as it results in only one unequal grid configuration.Simulation results are obtained by theMATLAB software developed.Percentage of improvement in ground potential rise,step voltage,touch voltage,and grid resistancewith variation in compression ratios are plotted.

Curve Fitting and Least Square Analysis to Extrapolate for the Case of COVID-19 Status in Ethiopia

On 30 January 2020 World Health Organization (WHO), declared the novel corona virus as a Public Health Emergency of International Concern (PHEIC), COVID-19 virus as an epidemic transmitted virus. It was on 31 December 2019, the WHO China Country office was informed the cases of pneumonia unknown etiology detected in Wuhan city, Hubei Province of China. Just after WHO’s declaration, Ethiopia has taken different measures to protect from this public health emergency problem. The disease is human to human transmitted virus. It comes from outside of the country, so that it opens check points in different entrance of the country. However, in 13 March 2020 the first positive case was reported from Japanese man. The virus is continuing the transmission in the public progressively more. While this research has been working, within 90 days from the first case, the country reported 2506 positive cases, 35 deaths. The research has done after collecting the first 90 days of data in Ethiopian case. Daily report announced by Ethiopian MoH is based on the test. And hence, the reported data as positive cases with COVID-19 is not actual positive case data in the country. There for, this paper has contribution for planning and taking further measure on the viruses by demonstrating the next 90 days predictive data. I use best curve fitting analysis using python function of the module polyfit algorithm to predict the trend of COVID-19 cases in Ethiopia.

Estimation of mass transfer coefficient in ozone absorption by linear least square fitting and Simplex search methods

For physical ozone absorption without reaction,two parametric estimation methods,i.e.the common linear least square fitting and non-linear Simplex search methods,were applied,respectively,to determine the ozone mass transfer coefficient during absorption and both methods give almost the same mass transfer coefficient.While for chemical absorption with ozone decomposition reaction,the common linear least square fitting method is not applicable for the evaluation of ozone mass transfer coefficient due to the difficulty of model linearization for describing ozone concentration dissolved in water.The nonlinear Simplex method obtains the mass transfer coefficient by minimizing the sum of the differences between the simulated and experimental ozone concentration during the whole absorption process,without the limitation of linear relationship between the dissolved ozone concentration and absorption time during the initial stage of absorption.Comparison of the ozone concentration profiles between the simulation and experimental data demonstrates that Simplex method may determine ozone mass transfer coefficient during absorption in an accurate and high efficiency way with wide applicability.

LEAST-SQUARES METHOD-BASED FEATURE FITTING AND EXTRACTION IN REVERSE ENGINEERING

The main purpose of reverse engineering is to convert discrete data pointsinto piecewise smooth, continuous surface models. Before carrying out model reconstruction it issignificant to extract geometric features because the quality of modeling greatly depends on therepresentation of features. Some fitting techniques of natural quadric surfaces with least-squaresmethod are described. And these techniques can be directly used to extract quadric surfaces featuresduring the process of segmentation for point cloud.

Least squares fitting of coordinate parameters model

This paper starts with untime-diversification of the time-diversification deformation model and gives displacement distribution model of untime-diversification and simplifies further the study of deformation model. The paper discusses the problem of least squares fitting of coordinate parameters model—parameters of deformation model. During discussion, the basic means of cubic B splines and two steps of multidimensional disorder datum fitting are adopted which can make fitting function calculated mostly approximate coordinate parameters model and it can make calculation easier.

Weighted Least-Squares for a Nearly Perfect Min-Max Fit

In this note, we experimentally demonstrate, on a variety of analytic and nonanalytic functions, the novel observation that if the least squares polynomial approximation is repeated as weight in a second, now weighted, least squares approximation, then this new, second, approximation is nearly perfect in the uniform sense, barely needing any further, say, Remez correction.

Generalized Kumaraswamy Generalized Power Gompertz Distribution: Statistical Properties, Application, and Validation Using a Modified Chi-Squared Goodness of Fit Test

A new six-parameter continuous distribution called the Generalized Kumaraswamy Generalized Power Gompertz (GKGPG) distribution is proposed in this study, a graphical illustration of the probability density function and cumulative distribution function is presented. The statistical features of the Generalized Kumaraswamy Generalized Power Gompertz distribution are systematically derived and adequately studied. The estimation of the model parameters in the absence of censoring and under-right censoring is performed using the method of maximum likelihood. The test statistic for right-censored data, criteria test for GKGPG distribution, estimated matrix Ŵ, Ĉ, and Ĝ, criteria test Y2n, alongside the quadratic form of the test statistic is derived. Mean simulated values of maximum likelihood estimates and their corresponding square mean errors are presented and confirmed to agree closely with the true parameter values. Simulated levels of significance for Y2n (γ) test for the GKGPG model against their theoretical values were recorded. We conclude that the null hypothesis for which simulated samples are fitted by GKGPG distribution is widely validated for the different levels of significance considered. From the summary of the results of the strength of a specific type of braided cord dataset on the GKGPG model, it is observed that the proposed GKGPG model fits the data set for a significance level ε = 0.05.

Calculation of stratum surface principal curvature based on a moving least square method

With the east section of the Changji sag Zhunger Basin as a case study, both a principal curvature method and a moving least square method are elaborated. The moving least square method is introduced, for the first time, to fit a stratum surface. The results show that, using the same-degree base function, compared with a traditional least square method, the moving least square method can produce lower fitting errors, the fitting surface can describe the morphological characteristics of stratum surfaces more accurately and the principal curvature values vary within a wide range and may be more suitable for the prediction of the distribution of structural fractures. The moving least square method could be useful in curved surface fitting and stratum curvature analysis.

Large Scattered Data Fitting Based on Radial Basis Functions

Solving large radial basis function （RBF） interpolation problem with non-customized methods is computationally expensive and the matrices that occur are typically badly conditioned. In order to avoid these difficulties, we present a fitting based on radial basis functions satisfying side conditions by least squares, although compared with interpolation the method loses some accuracy, it reduces the computational cost largely. Since the fitting accuracy and the non-singularity of coefficient matrix in normal equation are relevant to the uniformity of chosen centers of the fitted RBE we present a choice method of uniform centers. Numerical results confirm the fitting efficiency.

A CONCISE M-METRIC LEAST SQUARE FORMULA FOR POLYNOMIAL ANALOGY

An M-metric least square method for polynomial analogy is presented. The relative normal eqUation is of diagonal form, such that the concise solution formula is explicit, and it is suitable to Parallel computation. On the other hand, by error analysis of a typical example, we can see that the presented method is reliable.

Iterative circle fitting based on circular attracting factor

An intuitive method for circle fitting is proposed. Assuming an approximate circle(CA,n) for the fitting of some scattered points, it can be imagined that every point would apply a force to CA,n, which all together form an overall effect that "draws" CA,n towards best fitting to the group of points. The basic element of the force is called circular attracting factor(CAF) which is defined as a real scalar in a radial direction of CA,n. An iterative algorithm based on this idea is proposed, and the convergence and accuracy are analyzed. The algorithm converges uniformly which is proved by the analysis of Lyapunov function, and the accuracy of the algorithm is in accord with that of geometric least squares of circle fitting. The algorithm is adopted to circle detection in grayscale images, in which the transferring to binary images is not required, and thus the algorithm is less sensitive to lightening and background noise. The main point for the adaption is the calculation of CAF which is extended in radial directions of CA,n for the whole image. All pixels would apply forces to CA,n, and the overall effect of forces would be equivalent to a force from the centroid of pixels to CA,n. The forces from would-be edge pixels would overweigh that from noisy pixels, so the following approximate circle would be of better fitting. To reduce the amount of calculation, pixels are only used in an annular area including the boundary of CA,n just in between for the calculation of CAF. Examples are given, showing the process of circle fitting of scattered points around a circle from an initial assuming circle, comparing the fitting results for scattered points from some related literature, applying the method proposed for circular edge detection in grayscale images with noise, and/or with only partial arc of a circle, and for circle detection in BGA inspection.

Design of Ballistic Consistency Based on Least Squares Support Vector Machine and Particle Swarm Optimization

In order to improve the firing efficiency of projectiles,it is required to use the universal firing table for gun weapon system equipped with a variety of projectiles.Moreover,the foundation of sharing the universal firing table is the ballistic matching for two types of projectiles.Therefore,a method is proposed in the process of designing new type of projectile.The least squares support vector machine is utilized to build the ballistic trajectory model of the original projectile,thus it is viable to compare the two trajectories.Then the particle swarm optimization is applied to find the combination of trajectory parameters which meet the criterion of ballistic matching best.Finally,examples show the proposed method is valid and feasible.

A SPACE THEORY BASIS FOR CURVE FITTING PROBLEMS

itherto, a precision Concept for curve fitting problems has not been set. By using the theory of functional analysis, the author of this paper established a space theory basis for curve fitting problems. Also given in the paper is the precision concept of the curve fitting problems and the method for constructing the fitting of a curve satisfying given precision requirements.

Study on Coal Consumption Curve Fitting of the Thermal Power Based on Genetic Algorithm

Coal consumption curve of the thermal power plant can reflect the function relationship between the coal consumption of unit and load, which plays a key role for research on unit economic operation and load optimal dispatch. Now get coal consumption curve is generally obtained by least square method, but which are static curve and these curves remain unchanged for a long time, and make them are incompatible with the actual operation situation of the unit. Furthermore, coal consumption has the characteristics of typical nonlinear and time varying, sometimes the least square method does not work for nonlinear complex problems. For these problems, a method of coal consumption curve fitting of the thermal power plant units based on genetic algorithm is proposed. The residual analysis method is used for data detection;quadratic function is employed to the objective function;appropriate parameters such as initial population size, crossover rate and mutation rate are set;the unit’s actual coal consumption curves are fitted, and comparing the proposed method with least squares method, the results indicate that fitting effect of the former is better than the latter, and further indicate that the proposed method to do curve fitting can best approximate known data in a certain significance, and they can real-timely reflect the interdependence between power output and coal consumption.

Perturbation Analysis of Structured Least Squares Problems and Its Application in Calibration of Interest Rate Term Structure

A structured perturbation analysis of the least squares problem is considered in this paper.The new error bound proves to be sharper than that for general perturbations. We apply the new error bound to study sensitivity of changing the knots for curve fitting of interest rate term structure by cubic spline.Numerical experiments are given to illustrate the sharpness of this bound.

Research on the Model of Linear Data Fitting Method

By using the method of least square linear fitting to analyze data do not exist errors under certain conditions, in order to make the linear data fitting method that can more accurately solve the relationship expression between the volume and quantity in scientific experiments and engineering practice, this article analyzed data error by commonly linear data fitting method, and proposed improved process of the least distance squ^re method based on least squares method. Finally, the paper discussed the advantages and disadvantages through the example analysis of two kinds of linear data fitting method, and given reasonable control conditions for its application.

基于幂加权最小二乘拟合的红外相机辐射定标方法

分析了现有线性度计算方法的不足,提出基于偏差/测量值的新线性度评价方式,通过该方式最小二乘拟合的低端温度偏差比高端大一个数量级,并采用加权拟合提高系统响应线性度。在分析不同光谱的温度和辐亮度拟合函数基础上,提出一种基于辐亮度倒数幂加权最小二乘线性拟合的地面和星上辐射定标方法,确认最佳权重幂次,建立了幂次n=1的加权最小二乘拟合外黑体线性定标方程、内黑体线性定标方程、内外黑体辐亮度转换模型。针对星上内黑体高精度两点定标建立了基于加权最小二乘拟合内外黑体辐亮度转换模型;针对星上黑体发射率退化提出了基于恒星定标的红外相机星上内黑体辐亮度定标修正方法,建立了外黑体辐亮度、内黑体辐亮度和恒星辐亮度转换模型。采用加权线性拟合后,积分时间10 ms的低温端外黑体反演偏差由1.63 K下降到0.52 K,内黑体偏差反演温度偏差由0.83 K下降到0.39 K,系统响应线性度明显提升。

曲线曲面局部最小二乘渐进迭代逼近

作为一种有效的大数据拟合方法,曲线曲面最小二乘渐进迭代逼近方法(LSPIA)吸引了众多研究者的关注,并获得了广泛的应用。针对LSPIA算法拟合局部数据点效果较差的问题,提出了一种局部的LSPIA算法,称为LOCAL-LSPIA。首先,给定初始曲线(曲面)并从给定的数据点中选择部分数据点;然后在初始曲线(曲面)上选择需要调整的控制点;最后,LOCAL-LSPIA通过迭代调整这一部分控制点来生成一系列局部变化的拟合曲线(曲面),并且保证生成的曲线(曲面)的极限是在仅调整这部分控制点的情况下拟合部分数据点的最小二乘结果。在多个曲线曲面拟合上的实验结果表明,为达到相同的拟合精度,LOCAL-LSPIA算法比LSPIA算法需要的步骤和运算时间更少。因此,LOCAL-LSPIA是有效的,而且在拟合局部数据的情况下比LSPIA算法的收敛速度更快。

具有多MO喷嘴垂直MOCVD反应腔外延层厚度均匀性的优化理论及应用

金属有机物化学气相淀积(metal organic chemical vapor deposition,MOCVD)作为异质结半导体材料外延的关键手段,其外延层厚度均匀性会直接影响产品的良率.本文将理论与实验相结合,针对3个MO源喷嘴的垂直反应腔MOCVD,将各MO源喷嘴等效为蒸发面源,并引入一等效高度来涵盖MOCVD的相关外延参数,建立外延层厚度与各MO源喷嘴流量间的定量关系,设计并利用EMCORE D125 MOCVD系统外延生长了AlGaAs谐振腔结构,根据实验测得的外延层厚度分布结果,利用最小二乘法对模型参数进行了拟合提取,基于提取的模型参数,给出了优化外延层厚度均匀性的方法.4 in(1 in=2.54 cm)外延片mapping反射谱的统计结果为,腔模的平均波长为651.89 nm,标准偏差为1.03 nm,厚度均匀性达到0.16%.同时外延生长了GaInP量子阱结构,4 in外延片mapping荧光光谱的统计结果为,峰值波长平均值为653.3 nm,标准偏差仅为0.46 nm,厚度均匀性达到0.07%.本文提出的调整外延层厚度均匀性的方法具有简单、有效、快捷的特点,且可以进一步推广至具有4个MO喷嘴以上的垂直反应腔MOCVD系统.

广场舞和健步走锻炼对绝经后女性体成分影响的研究

为探讨长期广场舞与健步走锻炼在改善绝经后女性体成分方面的优劣以及锻炼年限与体成分之间的相关关系,本研究招募长期分别以广场舞与健步走锻炼为主的绝经后女性各40人(广场舞组和健步走组),长期为非体育人口的绝经后女性40人(对照组),测量其体成分。结果显示:除了骨骼肌外,广场舞组各指标值与对照组之间均具有统计学差异(P<0.05);健步走组体脂肪、体脂率和健康评估指标值与对照组之间均具有统计学差异(P<0.05);广场舞组体脂率指标值显著低于健步走组(P<0.05)。在相关性方面,广场舞组绝经后女性锻炼年限均分别与体脂肪、体脂率、骨肌比和健康评估指标值间存在高度负相关关系(P<0.01);健步走组绝经后女性的锻炼年限与体脂率指标值之间呈高度负相关关系,而与体脂肪、骨肌比和健康评估指标值之间呈中度正相关关系(P<0.01)。结果表明:长期广场舞与健步走锻炼均能改善绝经后女性的体成分,主要表现为降低体脂,提高健康水平,且广场舞的改善效果优于健步走。广场舞与健步走的锻炼年限与绝经后女性的体脂肪、体脂率、骨肌比和健康评估均呈高度相关关系,但广场舞锻炼的相关程度大于健步走锻炼,这可能与广场舞锻炼的运动强度高于健步走有关。