Subsidence prediction method based on equivalent mining height theory for solid backfilling mining

Based on the characteristics of strata movement of solid backfilling mining technology, the surface subsidence prediction method based on the equivalent mining height theory was proposed, and the parameters selection guideline of this method was also described. While comparing the parameters of caving mining with equivalent height, the subsidence efficient can be calculated according to the mining height and bulk factor of sagging zone and fracture zone, the tangent of main influence angle of solid backfilling mining is reduced by 0.2-0.5（while it cannot be less than 1.0）. For sake of safety, offset of the inflection point is set to zero, and other parameters, such as horizontal movement coefficient and main propagation angle are equal to the corresponding parameters of caving mining with equivalent height. In the last part, a case study of solid backfilling mining subsidence prediction was described. The results show the applicability of this method and the difference of the maximum subsidence point between the prediction and the observation is less than 5%.

CFD Simulation of Flow and Mass Transfer in Structured Packing Distillation Columns

Detailed investigation of flow behavior in structured packing distillation columns is of great importance in accurate prediction of process efficiency and development of more efficient and optimal equipment internals. In this study, a three-dimensional two-phase flow model based on VOF method for simulating the hydrodynamics and mass-transfer behavior in a typical representative unit of the structured packing is developed. In the proposed model, the c 2 - ε c model is used for the closure of turbulent mass transfer equation. By solving the proposed model, the velocity distribution, phase fraction profile and concentration field are obtained. Using these data, the total liquid holdup, the wetted area and the separation efficiency [height equivalent to a theoretical plate (HETP)] are estimated. For testing the model validation, the simulated HETPs are compared with our previous experimental data obtained in a 150 mm-diameter column containing Mellapak 350Y operating at the pressures of 0.6-1.8 MPa. The compari-son shows that they are in satisfactory agreement, with an average absolute deviation (AAD) of 25.4%.

An investigation of surface deformation after fully mechanized,solid back fill mining

The surface deformation after fully mechanized back filling mining was analyzed.The surface deformation for different backfill materials was predicted by an equivalent mining height model and numerical simulations.The results suggest that:(1) As the elastic modulus,E,of the backfill material increases the surface subsidence decreases.The rate of subsidence decrease drops after E is larger than 5 GPa;(2) Fully mechanized back fill mining technology can effectively control surface deformation.The resulting surface deformation is within the specification grade I,which means surface maintenance is not needed.A site survey showed that the equivalent mining height model is capable of predicting and analyzing surface deformation and that the model is conservative enough for engineering safety.Finally,the significance of establishing a complete error correction system based on error analysis and correction is discussed.

Numerical modeling investigation on turbulent oscillatory flow over a plane rough bed composed by randomly arrayed particles

A three-dimensional numerical model is established to simulate the turbulent oscillatory boundary layer over a fixed and rough bed composed by randomly arrayed solid spheres based on the lattice Boltzmann method and the large eddy simulation model.The equivalent roughness height,the location of the theoretical bed and the time variation of the friction velocity are investigated using the log-fit method.The time series of turbulent intensity and Reynolds stress are also investigated.The equivalent roughness height of cases with Reynolds numbers of 1×10^4–6×10^4 is approximately 2.81 d（grain size）.The time variation of the friction velocity in an oscillatory cycle exhibits sinusoidal-like behavior.The friction factor depends on the relative roughness in the rough turbulent regime,and the pattern of solid particles arrayed as the rough bed in the numerical simulations has no obvious effect on the friction factor.

A new method for retrieving equivalent cloud base height and equivalent emissivity by using the ground-based Atmospheric Emitted Radiance Interferometer (AERI)

In the paper, we propose a new method of identifying the clear sky based on the Atmospheric Emitted Radiance Interferometer （AERI）. Using the Atmospheric Radiation Measurement （ARM） Mobile Facility （AFM） dataset in Shouxian in 2008, we sim- ulate the downwelling radiances on the surface in the 8-12 μm window region using Line-By-Line Radiative Transfer Model （LBLRTM）, and compare the results with the AERI radiances, The differences larger （smaller） than 3 mW （cm2 sr cm-1）-1 suggest a cloudy （clear） sky. Meanwhile, we develop the new algorithms for retrieving the zenith equivalent cloud base height （CBHe） and the equivalent emissivity （ee）, respectively. The retrieval methods are described as follows. （1） An infinitely thin and isothermal blackbody cloud is simulated by the LBLRTM. The cloud base height （H） is adjusted iteratively to satisfy the situation that the contribution of the blackbody to the downwelling radiance is equal to that of realistic cloud. The final H is considered as CBHe. The retrieval results indicate that the differences between the CBHe and observational cloud base height （CBH） are much smaller for thick low cloud, and increase with the increasing CBH. （2） An infinitely thin and isothermal gray body cloud is simulated by the LBLRTM, with the CBH specified as the observed value. The cloud base emissivity （co） is ad- justed iteratively until the contribution of the gray body to the downwelling radiance is the same as that of realistic cloud. The corresponding εc is εe. The average εe for the low, middle, and high cloud is 0.967, 0.781, and 0.616 for the 50 cases, respec- tively. It decreases with the increasing CBH. The retrieval results will be useful for studying the role of cloud in the radiation budget in the window region and cloud parameterizations in the climate model.

WHU-Grace01s:A new temporal gravity field model recovered from GRACE KBRR data alone

A new temporal gravity field model called WHU-Grace01s solely recovered from Gravity Recovery and Climate Experiment （GRACE） K-Band Range Rate （KBRR） data based on dynamic integral approach is presented in this paper. After meticulously preprocessing of the GRACE KBRR data, the root mean square of its post residuals is about 0.2 micrometers per second, and seventy-two monthly temporal solutions truncated to degree and order 60 are computed for the period from January 2003 to December 2008. After applying the combi- nation filter in WHU-Grace01s, the global temporal signals show obvious periodical change rules in the large-scale fiver basins. In terms of the degree variance, our solution is smaller at high degrees, and shows a good consistency at the rest of degrees with the Release 05 models from Center for Space Research （CSR）, GeoForschungsZentrum Potsdam （GFZ） and Jet Pro- pulsion Laboratory 0PL）. Compared with other published models in terms of equivalent water height distribution, our solution is consistent with those published by CSR, GFZ, JPL, Delft institute of Earth Observation and Space system （DEOS）, Tongji University （Tongji）, Institute of Theoretical Geodesy （ITG）, Astronomical Institute in University of Bern （AIUB） and Groupe de Recherche de Geodesie Spatiale （GRGS}, which indicates that the accuracy of WHU-Grace01s has a good consistency with the previously published GRACE solutions.

Monthly gravity field recovery from GRACE orbits and K-band measurements using variational equations approach

The Gravity Recovery and Climate Experiment（GRACE） mission can significantly improve our knowledge of the temporal variability of the Earth＇s gravity field.We obtained monthly gravity field solutions based on variational equations approach from GPS-derived positions of GRACE satellites and K-band range-rate measurements.The impact of different fixed data weighting ratios in temporal gravity field recovery while combining the two types of data was investigated for the purpose of deriving the best combined solution.The monthly gravity field solution obtained through above procedures was named as the Institute of Geodesy and Geophysics（IGG） temporal gravity field models.IGG temporal gravity field models were compared with GRACE Release05（RL05） products in following aspects：（i） the trend of the mass anomaly in China and its nearby regions within 2005-2010; （ii） the root mean squares of the global mass anomaly during 2005-2010; （iii） time-series changes in the mean water storage in the region of the Amazon Basin and the Sahara Desert between 2005 and 2010.The results showed that IGG solutions were almost consistent with GRACE RL05 products in above aspects（i）-（iii）.Changes in the annual amplitude of mean water storage in the Amazon Basin were 14.7 ± 1.2 cm for IGG,17.1 ± 1.3 cm for the Centre for Space Research（CSR）,16.4 ± 0.9 cm for the GeoForschungsZentrum（GFZ） and 16.9 ± 1.2 cm for the Jet Propulsion Laboratory（JPL） in terms of equivalent water height（EWH）,respectively.The root mean squares of the mean mass anomaly in Sahara were 1.2 cm,0.9 cm,0.9 cm and 1.2 cm for temporal gravity field models of IGG,CSR,GFZ and JPL,respectively.Comparison suggested that IGG temporal gravity field solutions were at the same accuracy level with the latest temporal gravity field solutions published by CSR,GFZ and JPL.