Optical channel pre-emphasis equalization is experimentally researched for a 270 km 40 × 40 Gbit/s wavelength division multiplexing （WDM） transmission system with three Erbium-doped fiber amplifiers （ED- FAs）...Optical channel pre-emphasis equalization is experimentally researched for a 270 km 40 × 40 Gbit/s wavelength division multiplexing （WDM） transmission system with three Erbium-doped fiber amplifiers （ED- FAs） and Raman amplifiers concatenated as booster amplifier. The channel imbalance of the overall system changes with different sets of power launched into EDFAs. By appropriately choosing the power input to concatenated EDFAs, the output spectrum of 40 channel signal can be equalized to the most extent. The merit of benefit can be around 5.5 dB by this pre-emphasis equalization. The requirement for the gain equalizer is therefore greatly released. Then the gain imbalance of the overall system and the power imbalance of 40 channels are compared and the two almost matches, but the significant difference lies on some channels. Finally, the pump power into Raman amplifier is also optimized, and another 1.3 dB improvement of channel equaliza- tion can be further achieved.展开更多
Presented is a theoretical study of double-clad Er-doped fiber power amplifier(EDFA). Two kinds of double clad fibers(DCF) with rectangular and "flower" inner clad shapes are studied, and these fibers have d...Presented is a theoretical study of double-clad Er-doped fiber power amplifier(EDFA). Two kinds of double clad fibers(DCF) with rectangular and "flower" inner clad shapes are studied, and these fibers have different coupling constants and propagation losses. We calculate the effective pump power absorption ratio along the fiber with different coupling constants from the first cladding to the doped core and with different propagation losses for the power in the inner cladding. Then the gains of the double clad Er-doped fiber amplifiers versus fiber lengths are calculated using the EDFA model based on propagation and rate equations of a homogeneous, two-level medium.展开更多
We propose a physical model of estimating noise and asymmetry brought by high isolation Bi-directional erbiumdoped fiber amplifiers(Bi-EDFAs),no spontaneous lasing even with high gain,in longdistance fiber-optic time ...We propose a physical model of estimating noise and asymmetry brought by high isolation Bi-directional erbiumdoped fiber amplifiers(Bi-EDFAs),no spontaneous lasing even with high gain,in longdistance fiber-optic time and frequency(T/F)synchronization system.It is found that the Rayleigh scattering noise can be suppressed due to the high isolation design,but the amplified spontaneous emission(ASE)noise generated by the high isolation Bi-EDFA and the bidirectional asymmetry of the transmission link caused by the high isolation Bi-EDFA will deteriorate the stability of the system.The calculated results show that under the influence of ASE noise,the frequency instability of a 1200 km system composed of 15 high isolation Bi-EDFAs is 1.773×10^(-13)/1 s.And the instability caused by asymmetry is 2.6064×10^(-16)/30000–35000 s if the total asymmetric length of the bidirectional link length is 30 m.The intensity noises originating from the laser and detector,the transfer delay fluctuations caused by the variation in ambient temperature and the jitter in laser output wavelength are also studied.The experiment composed of three high isolation Bi-EDFAs is done to confirm the theoretical analysis.In summary,the paper shows that the short-term instability of the T/F synchronization system composed of high isolation Bi-EDFAs is limited by the accumulation of ASE noise of amplifiers and the laser frequency drift,while the long-term instability is limited by the periodic variation in ambient temperature and the asymmetry of the amplifiers.The research results are useful for pointing out the direction to improve the stability of the fiber-optic T/F synchronization system.展开更多
A few-mode erbium-doped fiber（FM-EDF） is fabricated using modified chemical vapor deposition in combination with liquid solution. The core and cladding diameters of the fiber are approximately 19.44 and 124.12 μm,r...A few-mode erbium-doped fiber（FM-EDF） is fabricated using modified chemical vapor deposition in combination with liquid solution. The core and cladding diameters of the fiber are approximately 19.44 and 124.12 μm,respectively. The refractive index difference is 0.98%, numerical aperture（NA） is 0.17, and normalized cut-off frequency at 1550 nm is 6.81. Therefore, it is a five-mode fiber, and can be used as a higher-order mode gain medium. Furthermore, a long period fiber grating（LPFG） is fabricated, which can convert LP〈01 mode to LP11 mode, and its conversion efficiency is up to 99%. The first-order orbital angular momentum（OAM） is also generated by combining the LPFG and polarization controller（PC）. Then, an all-fiber amplification system based on the FM-EDF and LPFG, for LP11 mode and first-order OAM beams, is built up. Its on-off gain of the LP11 mode beam is 37.2 d B at 1521.2 nm. The variation, whose transverse mode field intensity of first-order OAM is increased with the increase of pumping power, is obvious. These show that both the LP11 mode and first-order OAM beams are amplified in the all-fiber amplification system. This is a novel all-fiber amplification scheme,which can be used in the optical communication fields.展开更多
Through the introduction of the overlapping factors between the light (pump and signal) intensities and the erbium doping distributions inside the fiber core, analytical solutions of homogeneously broadened two-level ...Through the introduction of the overlapping factors between the light (pump and signal) intensities and the erbium doping distributions inside the fiber core, analytical solutions of homogeneously broadened two-level systems for erbium-doped fiber amplifiers pumped in the 980 nm absorption band have been derived from EDFA rate equations and light propagation equations in steady-state case. By using these deduced expressions and numerical simulated methods, important features characterizing the amplifiers such as gain, pump threshold power, optimum fiber length have been analyzed and discussed.展开更多
In an erbium-doped fiber amplifier(EDFA), erbium ions act as a three-level system. Therefore, much higher pump energy is required to achieve the population inversion in an erbium-doped fiber(EDF). This higher pump ene...In an erbium-doped fiber amplifier(EDFA), erbium ions act as a three-level system. Therefore, much higher pump energy is required to achieve the population inversion in an erbium-doped fiber(EDF). This higher pump energy requirement complicates the efficient design of an EDFA. However, efficient use of the pump power can improve the EDFA performance. The improved performance of an EDFA can be obtained by reducing the doping radius of the EDF. A smaller doping radius increases pump–dopant interactions and subsequently increases the pump–photon conversion efficiency. Decreasing the doping radius allows a larger proportion of dopant ions,which are concentrated near the core, to interact with the highest pump intensity. However, decreasing the doping radius beyond a certain limit will bring the dopant ions much closer and introduce detrimental ion–ion interaction effects. In this Letter, we show that an optimal doping radius in an EDF can provide the best gain performance. Moreover, we have simulated the well-known numerical aperture effects on EDFA gain performance to support our claim.展开更多
Transient response of an erbium-doped fiber amplifier(EDFA) is studied in an externally-modulated analog link.Double tones represented as transmitted radio frequency and dither signals are introduced.Extra modulation ...Transient response of an erbium-doped fiber amplifier(EDFA) is studied in an externally-modulated analog link.Double tones represented as transmitted radio frequency and dither signals are introduced.Extra modulation is generated owing to the EDFA’s transient response caused by a low-frequency dither signal.Therefore,the parasitic modulation is superposed to the output signals and may significantly affect in-band electrical spectra.Analytical and numerical solutions are both given,which agree well with experimental results.This work indicates that a suitable dither signal should be selected to maximize the carrier to intermodulation ratio.In-band spurious free dynamic range is optimized in the meantime.展开更多
The dynamic gain of a few-mode erbium-doped fiber amplifier(FM-EDFA)is vital for the long-haul mode division multiplexing(MDM)transmission.Here,we investigate the mode-dependent dynamic gain of an FM-EDFA under variou...The dynamic gain of a few-mode erbium-doped fiber amplifier(FM-EDFA)is vital for the long-haul mode division multiplexing(MDM)transmission.Here,we investigate the mode-dependent dynamic gain of an FM-EDFA under various manipulations of the pump mode.First,we numerically calculate the gain variation with respect to the input signal power,where a modedependent saturation input power occurs under different pump modes.Even under the fixed intensity profile of the pump laser,the saturation input power of each spatial mode is different.Moreover,high-order mode pumping leads to a compression of the linear amplification region,even though it is beneficial for the mitigation of the differential modal gain(DMG)arising in all guided modes.Then,we develop an all-fiber 3-mode EDFA,where the fundamental mode of the pump laser can be efficiently converted to the LP_(11)mode using the all-fiber mode-selective coupler(MSC).In comparison with the traditional LP_(01)pumping scheme,the DMG at 1550 nm can be mitigated from 1.61 dB to 0.97 dB under the LP_(11)mode pumping,while both an average gain of 19.93 dB and a DMG of less than 1 dB can be achieved from 1530 nm to 1560 nm.However,the corresponding signal input saturation powers are reduced by 0.3 dB for the LP_(01)mode and 1.6 dB for the LP_(11)mode,respectively.Both theoretical and experimental results indicate that a trade-off occurs between the DMG mitigation and the extension of the linear amplification range when the intensity profile of pump laser is manipulated.展开更多
基金the National Natural Science Foundation of China (60777024)
文摘Optical channel pre-emphasis equalization is experimentally researched for a 270 km 40 × 40 Gbit/s wavelength division multiplexing （WDM） transmission system with three Erbium-doped fiber amplifiers （ED- FAs） and Raman amplifiers concatenated as booster amplifier. The channel imbalance of the overall system changes with different sets of power launched into EDFAs. By appropriately choosing the power input to concatenated EDFAs, the output spectrum of 40 channel signal can be equalized to the most extent. The merit of benefit can be around 5.5 dB by this pre-emphasis equalization. The requirement for the gain equalizer is therefore greatly released. Then the gain imbalance of the overall system and the power imbalance of 40 channels are compared and the two almost matches, but the significant difference lies on some channels. Finally, the pump power into Raman amplifier is also optimized, and another 1.3 dB improvement of channel equaliza- tion can be further achieved.
基金Foundation of Beijing Jiaotong University(2005RC034)
文摘Presented is a theoretical study of double-clad Er-doped fiber power amplifier(EDFA). Two kinds of double clad fibers(DCF) with rectangular and "flower" inner clad shapes are studied, and these fibers have different coupling constants and propagation losses. We calculate the effective pump power absorption ratio along the fiber with different coupling constants from the first cladding to the doped core and with different propagation losses for the power in the inner cladding. Then the gains of the double clad Er-doped fiber amplifiers versus fiber lengths are calculated using the EDFA model based on propagation and rate equations of a homogeneous, two-level medium.
基金the National Natural Science Foundation of China(Grant Nos.61701040,61771062,and 61871044)the Youth Program of the National Natural Science Foundation of China(Grant No.61901046)+1 种基金the Fundamental Research Funds for the Central Universities,China(Grant Nos.2019XD-A18and 2019PTB-004)the Youth Research and Innovation Program of BUPT(Grant No.2017RC13)。
文摘We propose a physical model of estimating noise and asymmetry brought by high isolation Bi-directional erbiumdoped fiber amplifiers(Bi-EDFAs),no spontaneous lasing even with high gain,in longdistance fiber-optic time and frequency(T/F)synchronization system.It is found that the Rayleigh scattering noise can be suppressed due to the high isolation design,but the amplified spontaneous emission(ASE)noise generated by the high isolation Bi-EDFA and the bidirectional asymmetry of the transmission link caused by the high isolation Bi-EDFA will deteriorate the stability of the system.The calculated results show that under the influence of ASE noise,the frequency instability of a 1200 km system composed of 15 high isolation Bi-EDFAs is 1.773×10^(-13)/1 s.And the instability caused by asymmetry is 2.6064×10^(-16)/30000–35000 s if the total asymmetric length of the bidirectional link length is 30 m.The intensity noises originating from the laser and detector,the transfer delay fluctuations caused by the variation in ambient temperature and the jitter in laser output wavelength are also studied.The experiment composed of three high isolation Bi-EDFAs is done to confirm the theoretical analysis.In summary,the paper shows that the short-term instability of the T/F synchronization system composed of high isolation Bi-EDFAs is limited by the accumulation of ASE noise of amplifiers and the laser frequency drift,while the long-term instability is limited by the periodic variation in ambient temperature and the asymmetry of the amplifiers.The research results are useful for pointing out the direction to improve the stability of the fiber-optic T/F synchronization system.
基金supported by the National Natural Science Foundation of China(Nos.61635006,61520106014,61475096,61422507,and 61635006)the Science and Technology Commission of Shanghai Municipality(No.15220721500)
文摘A few-mode erbium-doped fiber（FM-EDF） is fabricated using modified chemical vapor deposition in combination with liquid solution. The core and cladding diameters of the fiber are approximately 19.44 and 124.12 μm,respectively. The refractive index difference is 0.98%, numerical aperture（NA） is 0.17, and normalized cut-off frequency at 1550 nm is 6.81. Therefore, it is a five-mode fiber, and can be used as a higher-order mode gain medium. Furthermore, a long period fiber grating（LPFG） is fabricated, which can convert LP〈01 mode to LP11 mode, and its conversion efficiency is up to 99%. The first-order orbital angular momentum（OAM） is also generated by combining the LPFG and polarization controller（PC）. Then, an all-fiber amplification system based on the FM-EDF and LPFG, for LP11 mode and first-order OAM beams, is built up. Its on-off gain of the LP11 mode beam is 37.2 d B at 1521.2 nm. The variation, whose transverse mode field intensity of first-order OAM is increased with the increase of pumping power, is obvious. These show that both the LP11 mode and first-order OAM beams are amplified in the all-fiber amplification system. This is a novel all-fiber amplification scheme,which can be used in the optical communication fields.
基金Project supported by the Chinese Academy of Sciences
文摘Through the introduction of the overlapping factors between the light (pump and signal) intensities and the erbium doping distributions inside the fiber core, analytical solutions of homogeneously broadened two-level systems for erbium-doped fiber amplifiers pumped in the 980 nm absorption band have been derived from EDFA rate equations and light propagation equations in steady-state case. By using these deduced expressions and numerical simulated methods, important features characterizing the amplifiers such as gain, pump threshold power, optimum fiber length have been analyzed and discussed.
基金support from King Fahd University of Petroleum and Minerals(KFUPM)King Abdulaziz City for Science and Technology(KACST)via KACST-TIC in Solid State Lighting(Nos.EE2381 and KACST TIC R2-FP-008)
文摘In an erbium-doped fiber amplifier(EDFA), erbium ions act as a three-level system. Therefore, much higher pump energy is required to achieve the population inversion in an erbium-doped fiber(EDF). This higher pump energy requirement complicates the efficient design of an EDFA. However, efficient use of the pump power can improve the EDFA performance. The improved performance of an EDFA can be obtained by reducing the doping radius of the EDF. A smaller doping radius increases pump–dopant interactions and subsequently increases the pump–photon conversion efficiency. Decreasing the doping radius allows a larger proportion of dopant ions,which are concentrated near the core, to interact with the highest pump intensity. However, decreasing the doping radius beyond a certain limit will bring the dopant ions much closer and introduce detrimental ion–ion interaction effects. In this Letter, we show that an optimal doping radius in an EDF can provide the best gain performance. Moreover, we have simulated the well-known numerical aperture effects on EDFA gain performance to support our claim.
文摘Transient response of an erbium-doped fiber amplifier(EDFA) is studied in an externally-modulated analog link.Double tones represented as transmitted radio frequency and dither signals are introduced.Extra modulation is generated owing to the EDFA’s transient response caused by a low-frequency dither signal.Therefore,the parasitic modulation is superposed to the output signals and may significantly affect in-band electrical spectra.Analytical and numerical solutions are both given,which agree well with experimental results.This work indicates that a suitable dither signal should be selected to maximize the carrier to intermodulation ratio.In-band spurious free dynamic range is optimized in the meantime.
基金supported by the National Key R&D Program of China(No.2018YFB1800903)the National Natural Science Foundation of China(No.U22A2087)+1 种基金the Guangdong Introducing Innovative and Entrepreneurial Teams of the Pearl River Talent Recruitment Program(No.2021ZT09X044)the Guangdong Provincial Key Laboratory of Photonics Information Technology(No.2020B121201011)。
文摘The dynamic gain of a few-mode erbium-doped fiber amplifier(FM-EDFA)is vital for the long-haul mode division multiplexing(MDM)transmission.Here,we investigate the mode-dependent dynamic gain of an FM-EDFA under various manipulations of the pump mode.First,we numerically calculate the gain variation with respect to the input signal power,where a modedependent saturation input power occurs under different pump modes.Even under the fixed intensity profile of the pump laser,the saturation input power of each spatial mode is different.Moreover,high-order mode pumping leads to a compression of the linear amplification region,even though it is beneficial for the mitigation of the differential modal gain(DMG)arising in all guided modes.Then,we develop an all-fiber 3-mode EDFA,where the fundamental mode of the pump laser can be efficiently converted to the LP_(11)mode using the all-fiber mode-selective coupler(MSC).In comparison with the traditional LP_(01)pumping scheme,the DMG at 1550 nm can be mitigated from 1.61 dB to 0.97 dB under the LP_(11)mode pumping,while both an average gain of 19.93 dB and a DMG of less than 1 dB can be achieved from 1530 nm to 1560 nm.However,the corresponding signal input saturation powers are reduced by 0.3 dB for the LP_(01)mode and 1.6 dB for the LP_(11)mode,respectively.Both theoretical and experimental results indicate that a trade-off occurs between the DMG mitigation and the extension of the linear amplification range when the intensity profile of pump laser is manipulated.
