Design of photonic crystal fiber with elliptical air-holes to achieve simultaneous high birefringence and nonlinearity

A new type of V-shaped photonic crystal fiber with elliptical air-holes is proposed to realize simultaneous high bire- fringence and nonlinearity at a wavelength of 1.55 μm. The full vector finite element method was adopted to investigate its characteristics, including birefringence, nonlinearity, and dispersion. The PCF exhibited a very high birefringence of 2.89x10-2 and very high nonlinear coefficient of 102.69 W-1 .km 1. In particular, there were two zero-dispersion wave- lengths （ZDWs） in the visible （X： 640-720 nm and Y： 730-760 nm） and near-infrared regions （X： 1050-1606 nm and Y： 850-1500 nm）. The combination of high birefringence and nonlinearity allowed the PCF to maintain the polarization state and generate a broadband super continuum, with potential applications in nonlinear optics.

Numerical analysis of a photonic crystal fiber based on two polarized modes for biosensing applications

This paper presents a theoretical study on a photonic crystal fiber plasmonic refractive index biosensor. The proposed photonic crystal fiber sensor introduces the concept of simultaneous detection with the linearly polarized and radially polarized modes because the sensing performance of the sensor based on both modes is relatively high, which will be useful for selecting the modes to make the detection accurately. The sharp single resonant peaks of the linearly polarized mode and radially polarized mode, are stronger and more sensitive to the variation of analyte refractive index than that of any other polarized mode in this kind of photonic crystal fiber. For linearly polarized mode and radially polarized mode, the maximum sensitivities of 10448.5nm per refractive index unit and 8230.7nm per refractive index unit can be obtained, as well as 949.8 and 791.4 for figure of merits in the sensing range of 1.33-1.45, respectively. Compared with the conventional Au-metalized surface plasmon resonance sensors, our device is better and can be applied as a biosensor.

Recent developments in high power near-infrared super-continuum generation based on photonic crystal fiber

High power supercontinuum generation has witnessed rapid developments during the past few years. The mecha- nism and the latest achievements in high power supercontinuum generation are reviewed both for the continuous wave pump regime and the pulsed pump regime. The challenges in scaling the average power of supereontinuum generation are analyzed. Some of our works on high power supercontinuum generation are summarized, and perspectives for the future development are discussed.

Supercontinuum generation in seven-core photonic crystal fiber pumped by a broadband picosecond pulsed fiber amplifier

We report a supercontinuum source generated in seven-core photonic crystal fibers（PCFs） pumped by a self-made all-fiber picosecond pulsed broadband fiber amplifier. The amplifier＇s output average power is 60 W at 1150 nm with spectral width of 260 nm, and its repetition rate is 8.47 MHz with pulse width of 221 ps. With two different lengths of seven-core PCF, different output powers and spectra are obtained. When a 10 m long seven-core PCF is chosen, the output supercontinuum covers the wavelength range from 620 nm to 1700 nm, with the output power of 11.7 W. With only 2 m long seven-core PCF used in the same experiment, the wavelength of the supercontinuum spans from 680 nm to 1700 nm,with the output power of 20.4 W. The results show that the pulse width is 385 ps in the 10 m long seven-core PCF and 255 ps in the 2 m long one, respectively, due to the normal dispersion of the PCF.

Generation of a compact high-power high-efficiency normal-dispersion pumping supercontinuum in silica photonic crystal fiber pumped with a 1064-nm picosecond pulse

Broadband normal dispersion pumping supercontinuum （SC） generation in silica photonic crystal fiber （PCF） is investigated in this paper. A 1064-nm picosecond fiber laser is used to pump silica PCF for the SC generation. The length of PCF is optimized for the most efficient stimulated Raman scattering process in the picosecond pump pulse region. The first stimulated Raman Stokes peak is located in the anomalous dispersion regime of the PCF and near the zero dispersion wavelength; thus the SC generation process can benefit from both a normal dispersion pumping scheme and an anomalous dispersion pumping scheme. The 51.7-W SC spanning from about 700 nm to beyond 1700 nm is generated with an all-fiber configuration, and the pump-to-SC conversion efficiency is up to 90%. In order to avoid the output fiber end face damage and increase the stability of the system, an improved output solution for the high power SC is proposed in our experiment. This high-efficiency near-infrared SC source is very suitable for applications in which average output power and spectral power density are firstly desirable.

Surface plasmon resonance-induced tunable polarization filters based on nanoscale gold film-coated photonic crystal fibers

Surface plasmon resonance induced tunable polarization filters based on nanoscale gold film-coated photonic crystal fibers were proposed and analyzed. The characteristics of the polarization filter were calculated by finite element method （FEM）. The gold film was selectively coated on the inner wall of one cladding air hole which was located near the fiber core along the y-axis direction. When the phase of core fundamental mode and surface plasmon polaritons （SPPs） mode matches, the two modes couple with each other intensely. Numerical results show that the resonance wavelength and strength vary with fiber structural parameters and the index of the infilling liquid. The fiber parameters were optimized to achieve specific functions. Under the optimal structure, we realized a dual channel filter at the communication wavelength of 1.31 μm and 1.55 μm fory polarization direction and x polarization direction. Then a single channel polarized filter at the communication wavelength of 1.55 μm is also achieved by adjusting the refractive index of the infilling liquid. The proposed polarization filters realized dual channel filtering and single channel filtering simultaneously under the same structure for the first time to the best of our knowledge.

Coupling characteristics of high birefringence dual-core As_2S_3 rectangular lattice photonic crystal fiber

A type of As2S3 chalcogenide glass mid-infrared dual-core photonic crystal fiber has been proposed. The dualcore photonic crystal fiber （PCF） consists of two asymmetric cores. The high polarization property and the coupling characteristics have been studied by using the finite dement method and mode coupling theory. Numerical results show that the birefringence at wavelength λ = 10 μm is up to 0.01386 and the coupling length can reach wavelength = 5 μm, 261 μm and 271.44 μm for x-polarized mode and y-polarized mode, respectively. It demonstrates that a 6.786-ram-long fiber can exhibit an extinction ratio of better than -10 dB and a bandwidth of 180 nm.

Designing of a polarization beam splitter for the wavelength of 1310 nm on dual-core photonic crystal fiber with high birefringence and double-zero dispersion

We have proposed a novel kind of photonic crystal fiber which contains two asymmetric cores. The bireti＇ingence and the dispersion are numerically analyzed based on finite element method when the size of the air holes and the pitch of two adjacent air holes are changed. It is shown that the proposed photonic crystal fiber has high birefringence up to the order of 10-2 and double-zero dispersion points are at the wavelengths of 1310 nm and 800 rim, simultaneously. At the same time, the normalized power and the extinction ratios of the proposed photonic crystal fiber have been simulated. It is demonstrated that, at the wavelength of 1310 rim, the x-polarized mode and the y-polarized mode are separated when the propagation distance is 2.481 ram.

Numerical analysis of photonic crystal fiber with chalcogenide core tellurite cladding composite microstructure

Kinds of photonic crystal fibers with chalcogenide core tellurite cladding composite microstructure are proposed. The multi-core photonic crystal fiber can reach the higher nonlinearity coefficient and the larger effective mode area. The small single-core photonic crystal fiber has a very high nonlinearity coefficient. At the wavelength λ=0.8μm, the nonlinearity coefficient can reach 31.37053 W-1·m-1, at the wavelength λ=1.55μm, the nonlinearity coefficient is 11.19686W-1·m-1.

Six-bit all-optical quantization using photonic crystal fiber with soliton self-frequency shift and pre-chirp spectral compression techniques

In this paper, we propose an optical quantization scheme for all-optical analog-to-digital conversion that facilitates photonics integration. A segment of 10-m photonic crystal fiber with a high nonlinear coefficient of 62.8 W-1/kin is utilized to realize large scale soliton self-frequency shift relevant to the power of the sampled optical signal. Furthermore, a 100-m dispersion-increasing fiber is used as the spectral compression module for further resolution enhancement. Simulation results show that 317-nm maximum wavelength shift is realized with 1550-nm initial wavelength and 6-bit quantization resolution is obtained with a subsequent spectral compression process.

Optimizational 6-bit all-optical quantization with soliton self-frequency shift and pre-chirp spectral compression techniques based on photonic crystal fiber

In this paper, we optimize a proposed all-optical quantization scheme based on soliton self-frequency shift(SSFS)and pre-chirp spectral compression techniques. A 10m-long high-nonlinear photonic crystal fiber(PCF) is used as an SSFS medium relevant to the power of the sampled optical pulses. Furthermore, a 10m-long dispersion flattened hybrid cladding hexagonal-octagonal PCF(6/8-PCF) is utilized as a spectral compression medium to further enhance the resolution. Simulation results show that 6-bit quantization resolution is still obtained when a 100m-long dispersion-increasing fiber(DIF)is replaced by a 6/8-PCF in spectral compression module.

Supercontinuum generated in all-normal dispersion photonic crystal fibers with picosecond pump pulses

The supercontinuum （SC） generation in all-normal dispersion （ANDi） photonic-crystal fiber （PCF） pumped by high power picosecond pulses are investigated in this paper. Our results show that an octave SC may be achieved by pumping the ANDi PCF with picosecond pump pulses. However, the PCF length required may have to be lengthened to several tens of centimeters, which is much longer than that with femtosecond pump pulses. The relatively long PCF gives rise to much higher Raman gain and stronger Raman frequency shift compared to those with femtosecond pump pulses, which in turn not only cause a distorted temporal waveform and an un-flattened spectrum, but also severely degrade the coherence of the generated SC.

Periodic Modulation of Nonlinearity in a Two-Core Photonic Crystal Fiber: A Numerical Investigation

We present a numerical investigation of the propagation and the switching of ultra-short pulses (100 fs) in a two-core nonlinear coupler of photonic crystal fibers constructed with periodically modulated the non-linearity fiber (PMNL-PFC). Our simulations are taking into account different amplitude and frequency modulations of the PMNL-PFC. A coupler for coupling whose length is Lc = 1.8 cm, the transmission characteristics, the compression factor, the crosstalk (Xtalk) and extinction ratio (Xratio) levels of the first order solitons were studied for low to high pump energies considering 2Lc. By an analysis on the reference channel (channel 2), it is observed that at low modulation frequencies an increase occurs in the switching power increasing transmission efficiency. For high modulation frequencies, the transmitted energy efficiency loses. The switching pulses are stronger for low frequency and high amplitude modulation. The Xtalk is a function of the measurement made on the secondary channel (channel 1). It was observed that this unwanted high-frequency energy increases to lessen the measure of the amplitude modulation. In summary, we have demonstrated that introduction of a non-linearity profile takes the periodically modulated PMNL-PFC to strong variations at transmission efficiency, Xtalk, Xratio a function of frequency and modulation amplitude and the input power.

Generation of a mid-infrared broadband polarized supercontinuum in As_2Se_3 photonic crystal fibers

A simplified structure of birefringent chalcogenide As 2 Se 3 photonic crystal fiber（PCF） is designed.Properties of birefringence,polarization extinction ratio,chromatic dispersion,nonlinear coefficient,and transmission are studied by using the multipole method,the finite-difference beam propagation method,and the adaptive split-step Fourier method.Considering that the zero dispersion wavelength of our proposed fiber is about 4 μm,we have analysed the mechanism of spectral broadening in PCFs with different pitches in detail,with femtosecond pulses at a wavelength of 4 μm as the pump pulses.Especially,mid-infrared broadband polarized supercontinuums are obtained in a 3-cm PCF with an optimal pitch of 2 μm.Their spectral width at 20 dB reaches up to 12 μm.In the birefringent PCF,we find that the supercontinuum generation changes with the pump alignment angle.Research results show that no coupling between eigenpolarization modes are observed at the maximum average power（i.e.,37 mW）,which indicates that the polarization state is well maintained.

Design of Photonic Crystal Fiber Capable of Carrying Multiple Orbital Angular Momentum Modes Transmission

For the traditional photonic crystal fibers with circular air holes, rectangular air holes are added to the fiber cladding. The periodic arrangement of the inner rectangular air holes allows the fiber structure to better match the annular mode field distribution of the vortex beam. The fiber structure was analyzed and calculated by COMSOL Multiphysics 5.4 finite element software, and the characteristics of fiber were analyzed, such as the dispersion, confinement loss, effective mode area and nonlinear coefficient. The results reveal that the photonic crystal fiber structure capable of carrying 50 orbital angular momentum (OAM) modes at the wavelength of 1.15 to 2.0 μm (850 nm). The effective refractive index difference Δneff between vector modes can reach 1 × 10-3, and larger difference can effectively separate the vector modes and improve the transmission performance of OAM modes. Moreover, the fiber has good performance, such as flat dispersion distribution of the low-order modes, low confinement loss below 10-9 dB·m-1, large effective mode field area and small nonlinear coefficient in the 850 nm wavelength range. Therefore, this fiber structure can be applied to the high-capacity communication system of fiber multiplexing OAM. In addition, the good characteristics of this fiber structure are of great significance for the transmission of vortex beam in fiber.

Dispersion Properties in Total Internal Reflective Photonic Crystal Fiber

The dispersion properties in the short wavelength region of total internal reflective photonic crystal fiber have been studied by using the models of the equivalent twin waveguide soliton coupling,effective refractive index,effective normalized frequency and dispersion management solitons.It is shown that the dispersion in the cladding waveguide of the total internal reflective photonic crystal fiber is a positive dispersion,and the dispersion of its core waveguide is a negative dispersion.The method of the compensated probing laser diffraction by the phase hole induced by the stationary pumping laser in the cladding waveguide enables the average dispersion value of the total internal reflective photonic crystal fiber to be close to zero and the zero dispersion point to shift to the short wavelength region.

Ultraviolet and mid-infrared continuum generation by cross-phase modulation between red-shifted solitons and blue-shifted dispersive waves in a photonic crystal fiber

Using a photonic crystal fiber with a zero dispersion wavelength of the fundamelItal mode at 780 nm designed and fabricated in our lab, the ultraviolet and mid-infrared continua are generated by cross-phase modulation between red-shift solitons and blue-shift dispersive waves. The dependences of continuum on the pump power and wavelength are investigated. With the pump working at 820 nm, when the pump power increases froul 300 to 500 mW, the bandwidths of ultraviolet and mid-infrared continua change from 80 to 140 nm and 100 to 200 nm, respectively. The wavelength of ultraviolet continuum is below 246 nm, and the wavelength of mid-infrared continuum exceeds 2500 nm. Moreover, the influences of pump power on wavelength and conversion efficiency of different parts of continua are also demonstrated.

Highly efficient Cherenkov radiation generation in the irregular point of hollow-core photonic crystal fiber

Highly efficient Cherenkov radiation （CR） is generated by the soliton self-frequency shift （SSFS） in the irregular point of a hollow-core photonic crystal fiber （HC-PCF） in our laboratory. The impacts of pump power and wavelength on the CR are investigated, and the corresponding nonlinear processes are discussed. When the average power of the 120 fs pump pulse increases from 500 mW to 700 mW, the Raman soliton shifts from 2210 nm to 2360 nm, the output power of the CR increases by 2.3 times, the maximum output power ratio of the CR at 539 nm to that of the residual pump is calculated to be 24.32：1, the width of the output optical spectrum at the visible wavelength broadens from 35 nm to 62 nm, and the conversion efficiency η of the CR in the experiment can be above 32%.

Supercontinuum Generationin Normal-dispersion Photonic Crystal Fiber Using Picosecond Pulse

Studied is the Super-continuum(SC) generation of a normal-dispersion photonic crystal fiber(PCF) using picosecond pulse excitation. In experimental analyses, a 237 nm broadband infrared continuum was generated pumped at 1 550 nm(normal dispersion regime) by 1.6 ps pulses from an erbium-doped fiber laser. In addition, we conduct the numerical analyses of SC based on generalized nonlinear Schr dionger equation. The results have been applied to investigate the dominant physical processes underlie the generation of SC. We conclude that dispersion, self-phase modulation(SPM),four-wave-mixing(FWM) and Raman scattering are determinants of SC generation rather than fission of soliton in normal-dispersion PCF.

Design of a polarization splitter for an ultra-broadband dual-core photonic crystal fiber

A novel ultra-broadband polarization splitter based on a dual-core photonic crystal fiber(DC-PCF)is designed.The full-vector finite element method and coupled-mode theory are employed to investigate the characteristics of the polarization splitter.According to the numerical results,a graphene-filled layer not only broadens the working bandwidth but also reduces the size of the polarization splitter.Furthermore,the fluorine-doped region and the germanium-doped region can broaden the bandwidth.Also,the 4.78 mm long polarization splitter can achieve an extinction ratio of-98.6 d B at a wavelength of 1550 nm.When extinction ratio is less than-20 d B,the range of the wavelength is 1027 nm-1723 nm with a bandwidth of 696 nm.Overall,the polarization splitter can be applied to all-optical network communication systems in the infrared and near-infrared wavelength range.