The indexing transmission chain error of gear cutting machines is an obviously periodic timefunction. If data are acquired properly while surveying and analyzing the error with grating typeinstrument attached to a mic...The indexing transmission chain error of gear cutting machines is an obviously periodic timefunction. If data are acquired properly while surveying and analyzing the error with grating typeinstrument attached to a micro-computer, the analysis will be easier and quicker. In this paper,such a system is introduced; a data acquiring interface is designed. Therefore, real-time samplingcan be performed. The results obtained from the indexing tramsmission chain error of several gearhobbing and shaping machines with this system were satisfactory.展开更多
We investigate chain teleportation of a qutrit-state via the non-maximally two-qutrit entangled channels.For the case of four parties,the efficiencies of two chain teleportation protocols,the separate chain teleportat...We investigate chain teleportation of a qutrit-state via the non-maximally two-qutrit entangled channels.For the case of four parties,the efficiencies of two chain teleportation protocols,the separate chain teleportation protocol(SCTP),and the global chain teleportation protocol (GCTP),are calculated.In SCTP the errors are corrected betweenevery step while in GCTP the errors are corrected only at the end.Furthermore,we present a piecewise global chainteleportation protocol (PGCTP) for keeping away from the inconvenience of error-correction of GCTP.We show thatPGCTP is more efficient than SCTP.展开更多
Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load, Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, a...Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load, Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, analysis, and noise characteristics of the chain drive system are weak. System design and noise characteristic are studied for a new type Gemini chain of dual-clutch automatic transmission. Based on the meshing theory of silent chain, the design parameters of the Gemini chain system are calculated and the mathematical models and dynamic analysis models of the Gemini chain system are established. Dynamic characteristics of the Gemini chain system is simulated and the contact force of plate and pin, plate and sprockets, the chain tension forces, the transmission error and the stress of plates and pins are analyzed. According to the simulation results of the Gemini chain system, the noise experiment about system is carried out. The noise values are tested at different speed and load and spectral characteristics are analyzed. The results of simulation and experimental show that the contact forces of plate and pin, plate and sprockets are smaller than the allowable stress values, the chain tension force is less than ultimate tension and transmission error is limited in 1.2%. The noise values can meet the requirements of industrial design, and it is proved that the design and analysis method of the Gemini chain system is scientific and feasible. The design and test system is built from analysis to test of Gemini chain system. This research presented will provide a corresponding theoretical guidance for the design and dynamic characteristics and noise characteristics of chain drive system.展开更多
Based on the two-level supply chain composed of suppliers and retailers, we assume that market demand is subject to an ARIMA(1, 1, 1). The supplier uses the minimum mean square error method (MMSE), the simple moving a...Based on the two-level supply chain composed of suppliers and retailers, we assume that market demand is subject to an ARIMA(1, 1, 1). The supplier uses the minimum mean square error method (MMSE), the simple moving average method (SMA) and the weighted moving average method (WMA) respectively to forecast the market demand. According to the statistical properties of stationary time series, we calculate the mean square error between supplier forecast demand and market demand. Through the simulation, we compare the forecasting effects of the three methods and analyse the influence of the lead-time L and the moving average parameter N on prediction. The results show that the forecasting effect of the MMSE method is the best, of the WMA method is the second, and of the SMA method is the last. The results also show that reducing the lead-time and increasing the moving average parameter improve the prediction accuracy and reduce the supplier inventory level.展开更多
文摘The indexing transmission chain error of gear cutting machines is an obviously periodic timefunction. If data are acquired properly while surveying and analyzing the error with grating typeinstrument attached to a micro-computer, the analysis will be easier and quicker. In this paper,such a system is introduced; a data acquiring interface is designed. Therefore, real-time samplingcan be performed. The results obtained from the indexing tramsmission chain error of several gearhobbing and shaping machines with this system were satisfactory.
基金Supported by the National Natural Science Foundation of China under Grant Nos.10971247 and 10905016Hebei Natural Science Foundation of China under Grant Nos.F2009000311and A2010000344the Key Project of Science and Technology Research of Education Ministry of China under Grant No.207011
文摘We investigate chain teleportation of a qutrit-state via the non-maximally two-qutrit entangled channels.For the case of four parties,the efficiencies of two chain teleportation protocols,the separate chain teleportation protocol(SCTP),and the global chain teleportation protocol (GCTP),are calculated.In SCTP the errors are corrected betweenevery step while in GCTP the errors are corrected only at the end.Furthermore,we present a piecewise global chainteleportation protocol (PGCTP) for keeping away from the inconvenience of error-correction of GCTP.We show thatPGCTP is more efficient than SCTP.
基金Supported by National Natural Science Foundation of China(Grant No.51305154)Jilin Provincial Science and Technology Development Program:Automobile Coordinated Action,China(Grant No.20116004)
文摘Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load, Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, analysis, and noise characteristics of the chain drive system are weak. System design and noise characteristic are studied for a new type Gemini chain of dual-clutch automatic transmission. Based on the meshing theory of silent chain, the design parameters of the Gemini chain system are calculated and the mathematical models and dynamic analysis models of the Gemini chain system are established. Dynamic characteristics of the Gemini chain system is simulated and the contact force of plate and pin, plate and sprockets, the chain tension forces, the transmission error and the stress of plates and pins are analyzed. According to the simulation results of the Gemini chain system, the noise experiment about system is carried out. The noise values are tested at different speed and load and spectral characteristics are analyzed. The results of simulation and experimental show that the contact forces of plate and pin, plate and sprockets are smaller than the allowable stress values, the chain tension force is less than ultimate tension and transmission error is limited in 1.2%. The noise values can meet the requirements of industrial design, and it is proved that the design and analysis method of the Gemini chain system is scientific and feasible. The design and test system is built from analysis to test of Gemini chain system. This research presented will provide a corresponding theoretical guidance for the design and dynamic characteristics and noise characteristics of chain drive system.
文摘Based on the two-level supply chain composed of suppliers and retailers, we assume that market demand is subject to an ARIMA(1, 1, 1). The supplier uses the minimum mean square error method (MMSE), the simple moving average method (SMA) and the weighted moving average method (WMA) respectively to forecast the market demand. According to the statistical properties of stationary time series, we calculate the mean square error between supplier forecast demand and market demand. Through the simulation, we compare the forecasting effects of the three methods and analyse the influence of the lead-time L and the moving average parameter N on prediction. The results show that the forecasting effect of the MMSE method is the best, of the WMA method is the second, and of the SMA method is the last. The results also show that reducing the lead-time and increasing the moving average parameter improve the prediction accuracy and reduce the supplier inventory level.
