Umami taste components in chicken-spices blends and potential effect of aroma on umami taste intensity

In this study,umami taste intensity(UTI)and umami taste components in chicken breast(CB)and chickenspices blends were characterized using sensory and instrumental analysis.Our main objective was to assess the aroma-umami taste interactions in different food matrices and reconcile the aroma-taste perception to assist future product development.The impact of key aroma,including vegetable-note"2-pentylfuran",meaty"methional",green"hexanal",and spicy-note-estragole and caryophyllene"on UTI was evaluated in monosodium glutamate and chicken extract.We found that spices significantly decreased UTI and umami taste components in CB.Interestingly,the perceptually similar odorants and tastants exhibited the potential to enhance UTI in food matrices.Methional was able to increase the UTI,whereas spicy and green-note components could reduce the UTI significantly.This information would be valuable to food engineers and formulators in aroma selection to control the UTI perceived by consumers,thus,improving the quality and acceptability of the chicken products.

Evaporate prediction and compensation of intake port wall-wetting fuel film for spark ignition engines fueled with ethanol-gasoline blends

The fuel dynamic transfer process,including fuel injection,fuel film deposition and evaporation in the intake port,was analyzed for spark ignition(SI) engines with port fuel injection(PFI).The influence of wall-wetting fuel film,especially its evaporation rate,upon the air-fuel ratio of in-cylinder mixtures was also discussed.According to the similarity principle,Fick's law,the ideal gas equation and the Gilliland correlation,an evaporate prediction model of wall-wetting fuel film was set up and an evaporate prediction based dynamic fuel film compensator was designed.Through engine cold start tests,the wall-wetting temperature,which is the key input of the fuel film evaporate prediction model,was also modeled and predicted.Combined with the experimental data of the evaporation characteristics of ethanol-gasoline blends and engine calibration tests,all the parameters of the wall-wetting fuel film evaporate prediction model used in the fuel film compensator were identified.Square-wave disturbance tests of fuel injection showed that with the help of the fuel film compensator the response of the in-cylinder air-fuel ratio was significantly improved and the real air-fuel ratio always closely matched the expected ratio.The fuel film compensator was then integrated into the final air-fuel ratio controller,and the engine tests showed that the air-fuel ratio control error was less than 2% in steady-state conditions,and less than 4% in transient conditions.The fuel film compensator also showed good adaptability to different ethanol-gasoline blends.

基于Blending-Clustering集成学习的大坝变形预测模型

【目的】变形是反映大坝结构性态最直观的效应量,构建科学合理的变形预测模型是保障大坝安全健康运行的重要手段。针对传统大坝变形预测模型预测精度低、误报率高等问题导致的错误报警现象,【方法】选取不同预测模型和聚类算法集成,构建了一种Blending-Clustering集成学习的大坝变形预测模型,该模型以Blending对单一预测模型集成提升预测精度为核心,并通过Clustering聚类优选预测值改善模型稳定性。以新疆某面板堆石坝变形监测数据为实例分析,通过多模型预测性能比较,对所提出模型的预测精度和稳定性进行全面评估。【结果】结果显示:Blending-Clustering模型将预测模型和聚类算法集成,均方根误差(RMSE)和归一化平均百分比误差(nMAPE)明显降低,模型的预测精度得到显著提高;回归相关系数(R~2)得到提升,模型具备更强的拟合能力;在面板堆石坝上22个测点变形数据集上的预测评价指标波动范围更小,模型的泛化性和稳定性得到有效增强。【结论】结果表明:Blending-Clustering集成预测模型对于预测精度、泛化性和稳定性均有明显提升,在实际工程具有一定的应用价值。

基于Prophet算法和Blending集成学习的实时负荷中期预测

目前的中期负荷预测一般未考虑负荷实时状态,而负荷数据的非线性、季节性、随机性、时序性特征将影响实时负荷的中期预测。构建一个实时负荷中期预测的框架,采用Prophet算法提取负荷数据的季节性部分,采用Blending集成学习对负荷数据的非季节部分进行滚动预测,将季节性部分和非季节性部分合成中期负荷实时数据。爱尔兰电力系统的算例结果验证了模型的有效性和稳定性。

A review:Health benefits and physicochemical characteristics of blended vegetable oils

Oil blending is the method of choice used worldwide to improve oxidative stability and nutritional value.There is no such edible oil/fat that meets all the recommendations from the health point of view.The fatty acid composition of vegetable oils decides the fate of the oil.Pure single oil is unable to provide a balanced amount of fatty acids(FAs)required/recommended on a daily intake basis.Blending oils/fats is an appropriate procedure of physically mixing multiple oils in suitable proportions which may provide functional lipids with improved antioxidant potential and desirable physical and chemical properties.This review piled up the accessible data on the blending of diverse oils/fats in the combination of binary,ternary,quaternary,or other types of oils into a single blended oil.Blending can be found very convincing towards appropriate FA profile,enhancement in physicochemical characteristics,and augmented stability for the period of storage or when used as cooking/frying processes which could ultimately serve as an effectual dietary intervention towards the health protectiveness.

Research on Blended Teaching Mode:A Case Study of Floristry

In order to better carry out research on education and teaching,the author consulted relevant literature on blended teaching mode from 2011-2021 through CNKI,Web of Science and other websites,summarized and analyzed the research status of blended teaching mode,in order to lay a good foundation for studying blended teaching mode in course teaching.

An Analysis on the Blended Teaching Mode of College English

This paper explores blended teaching in college English from five aspects:the connotation,theoretical basis,design principles,advantages,and challenges of blended teaching and blended teaching models.The purpose is to attract more foreign language practitioners and learners to pay attention to this model and put it into practice.

基于Blending集成学习的多源信息液压系统多类故障诊断研究

针对传统故障诊断方法准确性不高、耗时长问题,研究通过多个EfficientNet模型对传感器数据进行预训练,并使用XGBoost作为元学习器,提出了一种基于Blending集成学习的多源信息液压系统多类故障诊断方法。实验结果表明,各个子分类器在训练次数达到300次后趋于收敛,准确率均达到95%左右。该方法具有较高的准确性和鲁棒性,为液压系统故障诊断提供了一种有效的解决方案。

Effects of Perceived Teacher Support on Student Behavioral Engagement in the Blended Learning Environment:Learning Experience as a Mediator

Blended learning(BL)has been widely adopted to improve students’academic achievements in higher education.However,its success relies mainly on student engagement,which plays an essential role in active learning and provides a rich understanding of students’experiences.The study utilized three self-designed scales-the Teacher Support Scale,Student Engagement Scale,and Student Learning Experience Scale-to gauge and examine the impact and relationship between perceived teacher support,student behavioral engagement,and the intermediary role of learning experiences.A cohort of 899 college students undertaking the obligatory College English course through BL modes across five Chinese universities actively participated by completing a comprehensive questionnaire.The results showed significant correlations between perceived teacher support,learning experience,and behavioral engagement.Perceived teacher support significantly predicted students’behavioral engagement,with socio-affective support exerting the most substantial predictive effects.All predictive effects were partially mediated by learning experience(learning mode,online resources,overall LMS-based learning,interaction with their instructor and peers,and learning outcome).The influence of perceived teacher support on behavioral engagement differed between students who reported the most positive(vs.negative)learning experiences.Suggestions for further research are offered for consideration.

Application Effect of Blended Education Strategy Based on the Learning Pass Platform in Phase III Cardiac Rehabilitation of Patients with Coronary Artery Disease

Objective:To explore the application effect of the blended education strategy based on the Learning Pass platform in the phase III cardiac rehabilitation of patients with coronary artery disease.Methods:90 patients diagnosed with coronary artery disease in the Department of Cardiology of our hospital from January 2019 to January 2021 were selected and divided into the control group and the experimental group according to the method of randomized numerical table,with 45 cases in each group.Both the experimental group and the control group received pre-discharge cardiac rehabilitation education by conventional means.The control group received education and supervision information via WeChat after discharge,while the experimental group joined the Learning Pass platform to receive online and offline hybrid education and supervision,with online as the mainstay and offline as a supplement.The disease cognitive level,self-management skills,quality of life,medication adherence,and emotional status of the two groups were compared.Results:The disease cognitive levels in the experimental group were significantly higher than those of the control group(P<0.05);the scores of the experimental group in terms of quality of life,self-management skills,and medication adherence were significantly higher than those of the control group(P<0.05);and the scores of anxiety and depression in the experimental group were significantly lower than those of the control group(P<0.05).Conclusion:The blended education strategy based on the Learning Pass platform has a significant application effect in phase III cardiac rehabilitation of patients with coronary artery disease.It can improve patients’disease cognitive level,self-management skills,and quality of life,and provide a basis for improving patients’prognosis.

Melting Behavior of PA6 and PA6/PE Blends Crystallized from Amorphous State

目的研究尼龙６及其与线性低密度聚乙烯共混物的非晶样品的熔融行为．方法采用ＤＳＣ技术探讨了退火温度、退火时间、ＤＳＣ扫描速率、以及连续多步退火等因素与冰水淬火样品中的尼龙６组分的熔融峰间的相互关系．结果与结论上述因素对尼龙６组分的熔融行为有较大的影响，共混使尼龙６的结晶度和结晶完善度降低，随退火时间的延长结晶度提高．与纯尼龙６相比，共混物中高温熔融峰的峰高明显降低．

Effect of Thermal Treatment on the PA-6 in the Blends

目的研究热处理条件对尼龙６及其在线性低密度聚乙烯共混物中的结晶非晶态样品的结晶熔融行为．方法采用ＤＳＣ技术探讨退火温度、退火时间、ＤＳＣ扫描速率以及连续多步退火等因素与尼龙６组分的熔融行为的相互关系．结果与结论存在一个临界ＤＳＣ扫描速率，对尼龙６的中间熔融峰有较大的影响．在尼龙６的熔点温度附近退火后，尼龙６的主熔融峰向高温方向移动．短时间退火处理对纯尼龙６的熔融行为比对共混物中尼龙６的影响大，与聚乙烯共混使得尼龙６的熔融峰的峰高明显降低。尼龙６的熔融行为与聚乙烯。

IMPROVED PROPERTIES OF METALLOCENE-CATALYZED LINEAR LOW-DENSITY POLYETHYLENE/POLYPROPYLENE BLENDS DURING ULTRASONIC EXTRUSION

Metallocene-catalyzed linear low-density polyethylene/polypropylene （mLLDPE/PP） blends were prepared by ultrasonic extrusion in this work. Their extrusion processing behaviors were estimated by online measured data, such as the die pressure and flow rate. Crystallization and mechanical properties of the blends were also investigated. The results show that the addition of PP improves the processing behaviors of mLLDPE, but has little effect on its mechanical properties. On the other hand, the addition of mLLDPE improves the impact strength of PP, but has little effect on its processing behavior. The processing behaviors and mechanical properties of mLLDPE/PP blends get further improved due to the presence of ultrasonic oscillation during extrusion. Compared with PP-rich blends, the apparent viscosity drop of mLLDPE-rich blends is more sensitive to ultrasonic oscillation. The ultrasonic oscillation affects the crystal nucleation, while barely the other crystalline behaviors of the blends.

THE EFFECT OF BLENDING SEQUENCE ON PHASE MORPHOLOGY OF NYLON 6/ABS/SMA BLENDS

The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene- styrene(ABS)over a composition range of 30-70 wt% using a styrene-maleic anhydride(SMA)copolymer as the compatibilizing agent with a constant content(5phr)was investigated.The results of the scanning electron microscope (SEM)observation revealed that compared with the binary blends of nylon 6 and ABS,the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of ny...

Preparation and emission characteristics of ethanol-diesel fuel blends

The preparation of ethanol-diesel fuel blends and their emission characteristics were investigated. Results showed the absolute ethanol can dissolve in diesel fuel at an arbitrary ratio and a small quantity of water(0.2%) addition can lead to the phase separation of blends. An organic additive was synthesized and it can develop the ability of resistance to water and maintain the stability of ethanol-diesel-trace amounts of water system. The emission characteristics of 10%, 20%, and 30% ethanol-diesel fuel blends, with or without additives, were compared with those of diesel fuel in a direct injection(DI) diesel engine. The experimental results indicated that the blend of ethanol with diesel fuel significantly reduced the concentrations of smoke, hydrocarbon(HC), and carbon monoxide(CO) in exhaust gas. Using 20% ethanol-diesel fuel blend with the additive of 2% of the total volume, the optimum mixing ratio was achieved, at which the bench diesel engine testing showed a significant decrease in exhaust gas. Bosch smoke number was reduced by 55%, HC emission by 70%, and CO emission by 45%, at 13 kW/1540 r/min. However, ethanol-diesel fuel blends produced a few ppm acetaldehydes and more ethanol in exhaust gas.

SUPER POLYOLEFIN BLENDS ACHIEVED VIA DYNAMIC PACKING INJECTION MOLDING:MORPHOLOGY AND PROPERTIES

As a long-term project aimed at developing super polyolefin blends, in this paper we summarize our work on themechanical reinforcement and phase morphology of polyolefin blends achieved by dynamic packing injection molding(DPIM). The main feature of this technology is that the specimen is forced to move repeatedly in the model by two pistonsthat move reversibly with the same frequency during cooling, which results in preferential orientation of the dispersed phaseas well as the matrix. The typical morphology of samples obtained via DPIM is a shear-induced morphology with a core inthe center, an oriented zone surrounding the core and a skin layer in the cross-section areas. Shear-induced phase dissolutionat a higher shear rate but phase separation at low shear rates is evident from AFM examination of LLDPE/PP (50/50) blends.The super polyolefin blends having high modulus (1.9-2.2 GPa), high tensile strength (100-120 MPa) and high impactstrength (6 times as that of pure HDPE) have been prepared by controlling the phase separation, molecular orientation andcrystal morphology.

EFFECTS OF COMPATIBILIZERS ON THE MECHANICAL PROPERTIES OF LOW DENSITY POLYETHYLENE/LIGNIN BLENDS

Low density polyethylene(LDPE)/lignin blends were prepared using melt blending.Two kinds of compatibilizers, ethylene-vinylacetate(EVA) which is softer than LDPE and polyethylene grafted with maleic anhydride(PE-g-MA) which is harder than LDPE were used to improve the interfacial adhesion.Scanning electron microscope(SEM) was used to investigate the dispersion of lignin in LDPE matrix.The results showed that both of the compatibilizers could improve the interaction between the low density polyethylene and l...

Blends of Poly(lactic acid) with Thermoplastic Acetylated Starch

Blends of poly（lactic acid）（PLA） and thermoplastic acetylated starch（ATPS） were prepared by means of the melt mixing method. The results show that PLA and ATPS were partially miscible, which was confirmed with the measurement of Tg by dynamic mechanical analysis（DMA） and differrential scanning calorimetry（DSC）. The mechanical and thermal properties of the blends were improved. With increasing the ATPS content, the elongation at break and impact strength were increased. The elongation at break increased from 5% of neat PLA to 25% of the blend PLA/ATPS40. It was found that the cold crystallization behavior of PLA changed evidently by addition of ATPS. The cold crystallization temperature（Tcc） of each of PLA/ATPS blends was found to shift to a lower temperature and the width of exothermic peak became narrow compared with that of neat PLA. The thermogravimetry analysis（TGA） results showed that the peak of derivative weight for ATPS moved to higher temperature with increasing PLA content in PLA/ATPS blends. It can be concluded that PLA could increase the thermal stability of ATPS. The rheological measurement reveals the melt elasticity and viscosity of the blends decreased with the increased concentration of ATPS, which was favorable to the processing properties of PLA.

Rheological Properties of Polymers: Structure and Morphology of Molten Polymer Blends

The article reviews a brief literature on the rheological properties of polymer melts and blends. Experimental results on polymer blends are summarized. Technically, vital types of multi-phase polymers such as compounds and blends are discussed. The importance of the rheological properties of polymer mixtures in the development of the phase structure is discussed. And the importance of considering the stress and/or strain history of a material sample in a rheological investigation is discussed. Finally, the outlook on the past, present and future developments in the field of polymer rheology are given. The review concludes with a brief discussion on the opportunities and challenges in the field of polymer blends and blend rheology.

STUDIES ON MISCIBILITY OF POLY (ε-CAPROLACTONE) AND ALIPHATIC POLYCARBONATE BLENDS AND DETERMINATION OF THEIR INTERACTION PARAMETER

In this paper the miscibility of poly (ε-caprolactone) (PCL) and aliphatic polycarbonate (APC) is studied by using DSC. The results show that PCL and APC are miscible in all ranges of composition. The interaction parameter between the polymers is calculated from the melting point depression data. Using optical microscope, the shapes of the PCL spherulites in the blends are observed.