Effect of Flow Directions on Multiphase Flow Boiling Heat Transfer Enhanced by Suspending Particles in a Circulating Evaporation System

A circulating fluidized bed evaporator(including down-flow, horizontal, and up-flow beds) was constructed to study the effect of flow directions on multiphase flow boiling heat transfer. A range of experimental investigations were carried out by varying amount of added particles(0-2%), circulation flow rate(2.15-5.16 m^3/h) and heat flux(8-16 kW/m^2). The comparison of heat transfer performance in different vertical heights of the horizontal bed was also discussed. Results reveal that the glass bead particle can enhance heat transfer compared with vapor-liquid two-phase flow for all beds. At a low heat flux(q = 8 kW/m), the heat-transfer-enhancing factor of the horizontal bed is obviously greater than those of the up-flow and down-flow beds. With the increase in the amount of added particles, the heat-transfer-enhancing factors of the up-flow and down-flow beds increase, whereas that of the horizontal bed initially increases and then decreases. However, at a high heat flux(q=16 kW/m), the heat-transfer-enhancing factors of the three beds show an increasing tendency with the increase in the amount of added particles and become closer than those at a low heat flux. For all beds, the heat-transfer-enhancing factor generally increases with the circulation flow rate but decreases with the increase in heat flux.

High Efficient Synthesis of Enzymatic 2-Ethylhexyl Ferulate at Solvent-Free and Reduced Pressure Evaporation System

The use of immobilized lipase from Candida antarctica (Novozymò 435) to catalyze ferulic acid of esterification was investigated in this study. The synthesis product was analyzed using HPLC. The results revealed that the major product was 2-ethylhexyl ferulate. Response surface methodology and 3-level-3-factor central composite rotatable design were adopted to evaluate the effects of synthesis variables, including reaction temperature (60℃- 80℃), enzyme amount (500 - 1500 PLU) and reaction time (8 - 24 h) on the percentage molar conversion of 2-ethylhexyl ferulate. The results showed that reaction temperature and reaction time were the most important parameters on percentage molar conversion. Based on ridge max analysis, the optimum conditions for synthesis were: reaction time 23 h, reaction temperature 71℃?and enzyme amount 1422 PLU. The molar conversion of actual experimental values was 98% under optimal conditions.

Recent strategies for constructing efficient interfacial solar evaporation systems

Interfacial solar evaporation(ISE)is a promising technology to relieve worldwide freshwater shortages owing to its high energy conversion efficiency and environmentally sustainable potential.So far,many innovative materials and evaporators have been proposed and applied in ISE to enable highly controllable and efficient solar-to-thermal energy conversion.With rational design,solar evaporators can achieve excellent energy management for lowering energy loss,harvesting extra energy,and efficiently utilizing energy in the system to improve freshwater production.Beyond that,a strategy of reducing water vaporization enthalpy by introducing molecular engineering for water-state regulation has also been demonstrated as an effective approach to boost ISE.Based on these,this article discusses the energy nexus in two-dimensional(2D)and three-dimensional(3D)evaporators separately and reviews the strategies for design and fabrication of highly efficient ISE systems.The summarized work offers significant perspectives for guiding the future design of ISE systems with efficient energy management,which pave pathways for practical applications.

Ionization Engineering of Hydrogels Enables Highly Efficient Salt‑Impeded Solar Evaporation and Night‑Time Electricity Harvesting

Interfacial solar evaporation holds immense potential for brine desalination with low carbon footprints and high energy utilization.Hydrogels,as a tunable material platform from the molecular level to the macroscopic scale,have been considered the most promising candidate for solar evaporation.However,the simultaneous achievement of high evaporation efficiency and satisfactory tolerance to salt ions in brine remains a challenging scientific bottleneck,restricting the widespread application.Herein,we report ionization engineering,which endows polymer chains of hydrogels with electronegativity for impeding salt ions and activating water molecules,fundamentally overcoming the hydrogel salt-impeded challenge and dramatically expediting water evaporating in brine.The sodium dodecyl benzene sulfonate-modified carbon black is chosen as the solar absorbers.The hydrogel reaches a ground-breaking evaporation rate of 2.9 kg m−2 h−1 in 20 wt%brine with 95.6%efficiency under one sun irradiation,surpassing most of the reported literature.More notably,such a hydrogel-based evaporator enables extracting clean water from oversaturated salt solutions and maintains durability under different high-strength deformation or a 15-day continuous operation.Meantime,on the basis of the cation selectivity induced by the electronegativity,we first propose an all-day system that evaporates during the day and generates salinity-gradient electricity using waste-evaporated brine at night,anticipating pioneer a new opportunity for all-day resource-generating systems in fields of freshwater and electricity.

Nitrogen-doped microporous graphite-enhanced copper plasmonic effect for solar evaporation

Water scarcity is a global challenge,and solar evaporation technology offers a promising and eco-friendly solution for freshwater production.Photothermal conversion materials(PCMs)are crucial for solar evaporation.Improving photothermal conversion efficiency and reducing water evaporation enthalpy are the two key strategies for the designing of PCMs.The desired PCMs that combine both of these properties remain a challenging task,even with the latest advancements in the field.Herein,we developed copper nanoparticles(NPs)with different conjugated nitrogen-doped microporous carbon coatings(Cu@C–N)as PCMs.The microporous carbon enveloping layer provides a highly efficient pathway for water transport and a nanoconfined environment that protects Cu NPs and facilitates the evaporation of water clusters,reducing the enthalpy of water evaporation.Meanwhile,the conjugated nitrogen nodes form strong metal-organic coordination bonds with the surface of copper NPs,acting as an energy bridge to achieve rapid energy transfer and provide high solar-to-vapor conversion efficiency.The Cu@C–N exhibited up to 89.4%solar-to-vapor conversion efficiency and an evaporation rate of 1.94 kgm^(−2) h^(−1) under one sun irradiation,outperforming conventional PCMs,including carbon-based materials and semiconductor materials.These findings offer an efficient design scheme for high-performance PCMs essential for solar evaporators to address global water scarcity.

Evaluation of Water Losses by Evaporation in the Nakanbe Basin

A numerical approach to heat and mass transfer in a large water reservoir is presented. This water reservoir is likened to a parallelepiped reservoir whose vertical and lower walls are adiabatic and impermeable. The equations that govern natural convection in water are solved by the finite volume method and Thomas’salgorithm. The adequacy between the velocity and pressure fields is ensured by the SIMPLE algorithm. We are going to evaluate the water losses by evaporation from three dams in the Nakanbé basin in Burkina Faso for a period of thirty years, that is to say from January 1, 1991, to March 15, 2020. The three dams have a rate of evaporation greater than 40% of the volume of water stored. Indeed the rate of evaporation in each dam increases with the water filling rate in the reservoir: we have observed the following results for each dam in the Nakanbé basin;for the date of 02/27/1988 to 03/13/2020., the Loumbila dam received a total volume of stored water of 22.02 Mm3 and 10.57 Mm3 as the total volume of water evaporated at the same date. At the Ouaga dam (2 + 3), it stored a water volume of 4.06 Mm3 and evaporated 2.03 Mm3 of its storage volume from 01/01/1988 to 05/07/2016. Finally, with regard to the Bagré dam, it stored 745.16 Mm3 of water and 365.13 Mm3 as the volume of water evaporated from 01/01/1993 to 03/31/2020.

Modeling and simulation of urea-water-solution droplet evaporation and thermolysis processes for SCR systems

A reliable mathematical model of urea-water-solution(UWS) droplet evaporation and thermolysis is developed.The well known Abramzon–Sirignano evaporation model is corrected by introducing an adjustment coefficient considering the different evaporation behaviors of UWS droplet at different ambient temperatures. A semidetailed kinetic scheme of urea thermolysis is developed based on Ebrahimian's work. Sequentially, the evaporation characteristics, decomposition efficiency of a single UWS droplet and deposit formation are simulated. As a result, the relation of evaporation time, relative velocity, exhaust temperature and droplet initial diameter is presented. Synchronously, it indicates that temperature is the decisive factor for urea thermolysis. Different temperatures result in different deposit components, and deposit yield is significantly influenced by temperature and decomposition time. The current work can provide guidance for designing urea injection strategy of SCR systems.

Recentadvancesincarbon‐basedmaterials for solar‐driven interfacial photothermal conversion water evaporation:Assemblies,structures,applications,and prospective

The shortage of fresh water in the world has brought upon a serious crisis to human health and economic development.Solar‐driven interfacial photothermal conversion water evaporation including evaporating seawater,lake water,or river water has been recognized as an environmentally friendly process for obtaining clean water in a low‐cost way.However,water transport is restricted by itself by solar energy absorption capacity's limits,especially for finite evaporation rates and insufficient working life.Therefore,it is important to seek photothermal conversion materials that can efficiently absorb solar energy and reasonably design solar‐driven interfacial photothermal conversion water evaporation devices.This paper reviews the research progress of carbon‐based photothermal conversion materials and the mechanism for solar‐driven interfacial photothermal conversion water evaporation,as well as the summary of the design and development of the devices.Based on the research progress and achievements of photothermal conversion materials and devices in the fields of seawater desalination and photothermal electric energy generation in recent years,the challenges and opportunities faced by carbon‐based photothermal conversion materials and devices are discussed.The prospect of the practical application of solar‐driven interfacial photothermal conversion evaporation technology is foreseen,and theoretical guidance is provided for the further development of this technology.

Polymer Modified Banana Pseudo Stem-based Interfacial Solar-driven Evaporation System

Interfacial solar-driven evaporation technique is an environmental friendly and cost-effective advanced approach for water purification using solar energy.Free energy sources are effectively utilized using the structural design of evaporators and functional materials.In this work,we have fabricated a solar-driven interfacial evaporation device with Banana Pseudo Stem(BPS)and a photothermal layer made up of PVA PDMS Carbon(PPC)is attached to it.High evaporation rate of 2.03 kg m^(−2) h^(−1) is achieved by the system under 1 sun illumination.Heat localization on interfacial surface,reflectance of photothermal layer,presence of micro-fluidic channels in BPS were studied using IR imaging,UV-DRS and SEM characterization techniques,respectively.Effective localization of interfacial temperature around 53℃ and very low reflectance of photothermal layer substantiates high photothermal conversion efficiency of the device.The complete purification of water containing high concentration of Rhodamine-B dye using BPS is a novel and simple approach for water purification.This is an eco-friendly,cost-efficient novel approach in fabrication of interfacial solar-driven evaporation system with high evaporation rate for purification of water containing high concentration of organic dye.

Semi Operational Prediction of the Dead Sea Evaporation—A Synoptic Systems Approach

The predictability of pan evaporation and air temperature in the southern part of the Dead-Sea region (Sdom) was investigated according to two approaches, prediction by mesoscale models and with the aid of synoptic classification. First, the predicted temperature, wind speed and relative humidity that directly affect the evaporation are obtained from the WRF mesoscale model predictions. Predictions according to multilinear regression equations and a Penman-Monteith approach were also validated against observations in Sdom. The WRF model predicts the temperature reasonably well. However, the wind speed and relative humidity predictions were found to be very poor. The unique approach in this paper is employing a semi-objective synoptic systems classification according to the global GFS model. Relationships were defined between the 19 Eastern Mediterranean’s (EM) synoptic systems and the Sdom evaporation, temperature, wind speed and relative humidity. A monthly evaluation was performed for each of the systems and the semi-objective prediction was verified by the semi-objective classification. Since some synoptic systems affect the evaporation and temperature similarly, the 19 synoptic systems were grouped into seven clusters, each containing systems with similar evaporation and temperature records. This method has yielded a significant improvement in the daily prediction of evaporation and temperature. Semi-objective definitions for the synoptic systems were performed for the ranges of 12 - 132 hours. The synoptic system approach succeeded in the prediction of the evaporation and temperature changes in Sdom for a few days in advance. The predictability skill for the 12 hour forecast achieved about 80% of success, dropping to 70% at 36 hours. For 60 to 132 hours the prediction stabilized at a skill of 60%.The method presented here is a new attempt to predict meteorological parameters by using a synoptic classification approach in the Dead-Sea area where even high-resolution mesoscale modeling forecasts are not very successful.

Micro–Nano Water Film Enabled High‑Performance Interfacial Solar Evaporation

Interfacial solar evaporation holds great promise to address the freshwater shortage.However,most interfacial solar evaporators are always filled with water throughout the evaporation process,thus bringing unavoidable heat loss.Herein,we propose a novel interfacial evaporation structure based on the micro–nano water film,which demonstrates significantly improved evaporation performance,as experimentally verified by polypyrrole-and polydopamine-coated polydimethylsiloxane sponge.The 2D evaporator based on the as-prepared sponge realizes an enhanced evaporation rate of 2.18 kg m^(−2)h^(−1)under 1 sun by fine-tuning the interfacial micro–nano water film.Then,a homemade device with an enhanced condensation function is engineered for outdoor clean water production.Throughout a continuous test for 40 days,this device demonstrates a high water production rate(WPR)of 15.9–19.4 kg kW^(−1)h^(−1)m^(−2).Based on the outdoor outcomes,we further establish a multi-objective model to assess the global WPR.It is predicted that a 1 m^(2)device can produce at most 7.8 kg of clean water per day,which could meet the daily drinking water needs of 3 people.Finally,this technology could greatly alleviate the current water and energy crisis through further large-scale applications.

Facile synthesis of chromium chloride/poly(methyl methacrylate) core/shell nanocapsules by inverse miniemulsion evaporation method and application as delayed crosslinker in secondary oil recovery

Cr(III)ehydrolyzed polyacrylamide(HPAM)gels have been extensively studied as a promising strategy controlling waste water production for mature oilfields.However,the gelation time of the current technologies is not long enough for in-depth placement.In this study,we report a novel synthesis method to obtain chromium chloride/poly(methyl methacrylate)(PMMA)nanocapsules which can significantly delay the gelation of HPAM through encapsulating the chromium chloride crosslinker.The chromium chloride-loaded nanocapsules(CreNC)are prepared via a facile inverse miniemulsion evaporation method during which the hydrophobic PMMA polymers,pre-dispersed in an organic solvent,were carefully controlled to precipitate onto stable aqueous miniemulsion droplets.The stable aqueous nanodroplets(W)containing Cr(III)are dispersed in a mixture of organic solvent(O1)with PMMA and nonsolvent medium(O2)to prepare an inverse miniemulsion.With the evaporation of the O1,PMMA forms CreNCs around the aqueous droplets.The CreNCs are readily transferred into water from the organic nonsolvent phase.The CreNCs exhibit the tunable size(358-983 nm),Cr loading(7.1%-19.1%),and Cr entrapment efficiency(11.7%-80.2%),with tunable zeta potentials in different PVA solutions.The CreNCs can delay release of Cr(III)and prolong the gelation time of HPAM up to 27 days.

Janus membrane with enhanced interfacial activation for solar evaporation

Low solar spectrum coverage,high evaporation enthalpy,and undesired salt deposition severely limited the solar-driven interfacial evaporation technology for further sewage purification and seawater desalination.To overcome these problems,we designed an amphiphilic Janus-structured polyaniline(PANI)/ZrC/cellulose acetate(CA)(J-PZCA) membrane.Firstly,the interfacial interaction between PANI and ZrC enhances the photoabsorption and photothermal conversion efficiency.Secondly,low thermal conductivity reduces the heat lost at the interface.Most importantly,ZrC could facilitate interfacial activation,which weakens the intermolecular forces of water by affecting the hydrogen bond.Under 1 solar irradiation(1 sun),the composite membrane exhibits a high evaporation rate of 1.31 kg m^(-2)h^(-1) and an excellent efficiency of 79.4%.In addition,the sewage purification and seawater desalination experiments reveal a remarkable purification capability of J-PZCA membrane.Especially for the treatment of high-concentration salt solution,it realizes a long-term stable evaporation performance due to the excellent salt deposition resistance.Therefore,the J-PZCA membrane constructed in this study provides a new perspective for the design of efficient interfacial evaporation devices.

Controllable growth of wafer-scale PdS and PdS_(2) nanofilms via chemical vapor deposition combined with an electron beam evaporation technique

Palladium(Pd)-based sulfides have triggered extensive interest due to their unique properties and potential applications in the fields of electronics and optoelectronics.However,the synthesis of large-scale uniform PdS and PdS_(2)nanofilms(NFs)remains an enormous challenge.In this work,2-inch wafer-scale PdS and PdS_(2) NFs with excellent stability can be controllably prepared via chemical vapor deposition combined with electron beam evaporation technique.The thickness of the pre-deposited Pd film and the sulfurization temperature are critical for the precise synthesis of PdS and PdS_(2) NFs.A corresponding growth mechanism has been proposed based on our experimental results and Gibbs free energy calculations.The electrical transport properties of PdS and PdS_(2) NFs were explored by conductive atomic force microscopy.Our findings have achieved the controllable growth of PdS and PdS_(2) NFs,which may provide a pathway to facilitate PdS and PdS_(2) based applications for next-generation high performance optoelectronic devices.

Effects of Groundwater with Various Salinities on Evaporation and Redistribution of Water and Salt in Saline-sodic Soils in Songnen Plain,Northeast China

Groundwater mineralization is one of the main factors affecting the transport of soil water and salt in saline-sodic areas.To investigate the effects of groundwater with different levels of salinity on evaporation and distributions of soil water and salt in Songnen Plain,Northeast China,five levels of groundwater sodium adsorption ration of water(SARw)and total salt content(TSC mmol/L)were conducted in an oil column lysimeters.The five treated groundwater labeled as ST0:0,ST0:10,ST5:40,ST10:70 and ST20:100,were prepared with NaCl and CaCl2 in proportion,respectively.The results showed the groundwater evaporation(GWE)and soil evaporation(SE)increased firstly and then decreased with the increase of groundwater salinity.The values of GWE and SE in ST10:70 treatment were the highest,which were 2.09 and 1.84 times the values in the ST0:0 treatment with the lowest GWE and SE.There was a positive linear correlation between GWE and the Ca^(2+)content in groundwater,with R^(2)=0.998.The soil water content(SWC)of ST0:0 treatment was significantly(P<0.05)less than those of other treatments during the test.The SWC of the ST0:0 and ST0:10 treatments increased with the increase of soil depth,while the other treatments showed the opposite trend.Statistical analysis indicated the SWC in the 0–60 cm soil layer was positively correlated with the groundwater TSC and its ion contents during the test.Salt accumulation occurred in the topsoil and the salt accumulation in the 0–20 cm soil layer was significantly(P<0.05)greater than that in the subsoil.This study revealed the effects of the salinity level of groundwater,especially the Ca^(2+)content and TSC of groundwater,on the GWE and distributions of soil water and salt,which provided important support for the prevention and reclamation of soil salinization and sodificaton in shallow groundwater regions.

Boosting extraction of Pb in contaminated soil via interfacial solar evaporation of multifunctional sponge

Interfacial solar water evaporation is a reliable way to accelerate water evaporation and contaminant remediation.Embracing the recent advance in photothermal technology,a functional sponge was prepared by coating a sodium alginate(SA)impregnated sponge with a surface layer of reduced graphene oxide(rGO)to act as a photothermal conversion medium and then subsequently evaluated for its ability to enhance Pb extraction from contaminated soil driven by interfacial solar evaporation.The SA loaded sponge had a Pb adsorption capacity of 107.4 mg g^(-1).Coating the top surface of the SA sponge with rGO increased water evaporation performance to 1.81 kg m^(-2)h^(-1)in soil media under one sun illumination and with a wind velocity of 2 m s^(-1).Over 12 continuous days of indoor evaporation testing,the Pb extraction efficiency was increased by 22.0%under 1 sun illumination relative to that observed without illumination.Subsequently,Pb extraction was further improved by 48.9%under outdoor evaporation conditions compared to indoor conditions.Overall,this initial work shows the significant potential of interfacial solar evaporation technologies for Pb contaminated soil remediation,which should also be applicable to a variety of other environmental contaminants.

Experimental study on the desulfurization and evaporation characteristics of Ca(OH)_(2) droplets

The experiments were conducted to focus on the desulfurization and evaporation characteristics of lime slurry droplets at 298-383 K. We designed an evaporation-reaction chamber with quartz glass windows.The monodisperse slurry droplet stream was injected into the evaporation reaction chamber, and the inlet gas components(air, air + SO_(2)) were introduced into the chamber. We applied the magnified digital in-line holography to measure the droplet parameters and calculated the evaporation rate. The effects of temperature, droplet concentration, and SO_(2) concentration on the evaporation rate of Ca(OH)_(2) droplets were discussed. Moreover, the Ca(OH)_(2) droplets under different experimental conditions were sampled,and the droplets were observed and analyzed using an off-line microscope. The evaporation rate of the Ca(OH)_(2) droplet increased at first, and then decreased during the falling process, and remained constant at last. The average evaporation rate of the Ca(OH)_(2) droplets increased significantly with the temperature increasing.

A Model for Droplet Evaporation

Based on the kinetic theory of gases, a simple model for droplet vaporization, in particular mercury, is developed to study the variation of droplet radius as a function of time. This model is in agreement with more sophisticated models for water, such as the kinetic model and the Kulmala model. Findings indicate that complete evaporation of a 1-mm-radius mercury droplet, in a ventilated room at normal temperatures, should take about 1.8 × 104 seconds or 5 hours. The findings of this study can be utilized to direct further research in the field of toxin remediation.

Chemical Scissors Tailored Nano‑Tellurium with High‑Entropy Morphology for Efficient Foam‑Hydrogel‑Based Solar Photothermal Evaporators

The development of tellurium(Te)-based semiconductor nanomaterials for efficient light-to-heat conversion may offer an effective means of harvesting sunlight to address global energy concerns.However,the nanosized Te(nano-Te)materials reported to date suffer from a series of drawbacks,including limited light absorption and a lack of surface structures.Herein,we report the preparation of nano-Te by electrochemical exfoliation using an electrolyzable room-temperature ionic liquid.Anions,cations,and their corresponding electrolytic products acting as chemical scissors can precisely intercalate and functionalize bulk Te.The resulting nano-Te has high morphological entropy,rich surface functional groups,and broad light absorption.We also constructed foam hydrogels based on poly(vinyl alcohol)/nano-Te,which achieved an evaporation rate and energy efficiency of 4.11 kg m^(−2)h^(−1)and 128%,respectively,under 1 sun irradiation.Furthermore,the evaporation rate was maintained in the range 2.5-3.0 kg m^(−2)h^(−1)outdoors under 0.5-1.0 sun,providing highly efficient evaporation under low light conditions.

A hierarchical salt-rejection strategy for sustainable and high-efficiency solar-driven desalination

Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.