Highly mass activity electrocatalysts with ultralow Pt loading on carbon black for hydrogen evolution reaction

Pt-based nanocatalysts offer excellent prospects for various industries.However,the low loading of Pt with excellent performance for efficient and stable nanocatalysts still presents a considerable challenge.In this study,nanocatalysts with ultralow Pt content,excellent performance,and carbon black as support were prepared through in-situ synthesis.These~2-nm particles uniformly and stably dispersed on carbon black because of the strong s-p-d orbital hybridizations between carbon black and Pt,which suppressed the agglomeration of Pt ions.This unique structure is beneficial for the hydrogen evolution reaction.The catalysts exhibited remarkable catalytic activity for hydrogen evolution reaction,exhibiting a potential of 100 mV at 100 mA·cm^(-2),which is comparable to those of commercial Pt/C catalysts.Mass activity(1.61 A/mg)was four times that of a commercial Pt/C catalyst(0.37 A/mg).The ultralow Pt loading(6.84wt%)paves the way for the development of next-generation electrocatalysts.

Role of iron ore in enhancing gasification of iron coke:Structural evolution,influence mechanism and kinetic analysis

The utilization of iron coke provides a green pathway for low-carbon ironmaking.To uncover the influence mechanism of iron ore on the behavior and kinetics of iron coke gasification,the effect of iron ore on the microstructure of iron coke was investigated.Furthermore,a comparative study of the gasification reactions between iron coke and coke was conducted through non-isothermal thermogravimetric method.The findings indicate that compared to coke,iron coke exhibits an augmentation in micropores and specific surface area,and the micropores further extend and interconnect.This provides more adsorption sites for CO_(2) molecules during the gasification process,resulting in a reduction in the initial gasification temperature of iron coke.Accelerating the heating rate in non-isothermal gasification can enhance the reactivity of iron coke.The metallic iron reduced from iron ore is embedded in the carbon matrix,reducing the orderliness of the carbon structure,which is primarily responsible for the heightened reactivity of the carbon atoms.The kinetic study indicates that the random pore model can effectively represent the gasification process of iron coke due to its rich pore structure.Moreover,as the proportion of iron ore increases,the activation energy for the carbon gasification gradually decreases,from 246.2 kJ/mol for coke to 192.5 kJ/mol for iron coke 15wt%.

Catalyst–Support Interaction in Polyaniline‑Supported Ni_(3)Fe Oxide to Boost Oxygen Evolution Activities for Rechargeable Zn‑Air Batteries

Catalyst–support interaction plays a crucial role in improving the catalytic activity of oxygen evolution reaction(OER).Here we modulate the catalyst–support interaction in polyaniline-supported Ni_(3)Fe oxide(Ni_(3)Fe oxide/PANI)with a robust hetero-interface,which significantly improves oxygen evolution activities with an overpotential of 270 mV at 10 mA cm^(-2)and specific activity of 2.08 mA cm_(ECSA)^(-2)at overpotential of 300 mV,3.84-fold that of Ni_(3)Fe oxide.It is revealed that the catalyst–support interaction between Ni_(3)Fe oxide and PANI support enhances the Ni–O covalency via the interfacial Ni–N bond,thus promoting the charge and mass transfer on Ni_(3)Fe oxide.Considering the excellent activity and stability,rechargeable Zn-air batteries with optimum Ni_(3)Fe oxide/PANI are assembled,delivering a low charge voltage of 1.95 V to cycle for 400 h at 10 mA cm^(-2).The regulation of the effect of catalyst–support interaction on catalytic activity provides new possibilities for the future design of highly efficient OER catalysts.

Low‑Temperature Oxidation Induced Phase Evolution with Gradient Magnetic Heterointerfaces for Superior Electromagnetic Wave Absorption

Gradient magnetic heterointerfaces have injected infinite vitality in optimizing impedance matching,adjusting dielectric/magnetic resonance and promoting electromagnetic(EM)wave absorption,but still exist a significant challenging in regulating local phase evolution.Herein,accordion-shaped Co/Co_(3)O_(4)@N-doped carbon nanosheets(Co/Co_(3)O_(4)@NC)with gradient magnetic heterointerfaces have been fabricated via the cooperative high-temperature carbonization and lowtemperature oxidation process.The results indicate that the surface epitaxial growth of crystal Co_(3)O_(4) domains on local Co nanoparticles realizes the adjustment of magnetic-heteroatomic components,which are beneficial for optimizing impedance matching and interfacial polarization.Moreover,gradient magnetic heterointerfaces simultaneously realize magnetic coupling,and long-range magnetic diffraction.Specifically,the synthesized Co/Co_(3)O_(4)@NC absorbents display the strong electromagnetic wave attenuation capability of−53.5 dB at a thickness of 3.0 mm with an effective absorption bandwidth of 5.36 GHz,both are superior to those of single magnetic domains embedded in carbon matrix.This design concept provides us an inspiration in optimizing interfacial polarization,regulating magnetic coupling and promoting electromagnetic wave absorption.

Experimental Observing Damage Evolution in Cement Pastes Exposed to External Sulfate Attack by in situ X-ray Computed Tomography

The paper presents experimental investigation results of crack pattern change in cement pastes caused by external sulfate attack(ESA).To visualize the formation and development of cracks in cement pastes under ESA,an X-ray computed tomography(X-ray CT)was used,i e,the tomography system of Zeiss Xradia 510 versa.The results indicate that X-CT can monitor the development process and distribution characteristics of the internal cracks of cement pastes under ESA with attack time.In addition,the C3A content in the cement significantly affects the damage mode of cement paste specimens during sulfate erosion.The damage of ordinary Portland cement(OPC)pastes subjected to sulfate attack with high C3A content are severe,while the damage of sulfate resistant Portland cement(SRPC)pastes is much smaller than that of OPC pastes.Furthermore,a quadratic function describes the correlation between the crack volume fraction and development depth for two cement pastes immermed in sulfate solution.

Boosting Oxygen Evolution Reaction Performance on NiFe‑Based Catalysts Through d‑Orbital Hybridization

Anion-exchange membrane water electrolyzers(AEMWEs)for green hydrogen production have received intensive attention due to their feasibility of using earth-abundant NiFe-based catalysts.By introducing a third metal into NiFe-based catalysts to construct asymmetrical M-NiFe units,the d-orbital and electronic structures can be adjusted,which is an important strategy to achieve sufficient oxygen evolution reaction(OER)performance in AEMWEs.Herein,the ternary NiFeM(M:La,Mo)catalysts featured with distinct M-NiFe units and varying d-orbitals are reported in this work.Experimental and theoretical calculation results reveal that the doping of La leads to optimized hybridization between d orbital in NiFeM and 2p in oxygen,resulting in enhanced adsorption strength of oxygen intermediates,and reduced rate-determining step energy barrier,which is responsible for the enhanced OER performance.More critically,the obtained NiFeLa catalyst only requires 1.58 V to reach 1 A cm^(−2) in an anion exchange membrane electrolyzer and demonstrates excellent long-term stability of up to 600 h.

Ru⁃doped Co_(3)O_(4)/reduced graphene oxide:Preparation and electrocatalytic oxygen evolution property

Binary composites(ZIF-67/rGO)were synthesized by one-step precipitation method using cobalt nitrate hexahydrate as metal source,2-methylimidazole as organic ligand,and reduced graphene oxide(rGO)as carbon carrier.Then Ru3+was introduced for ion exchange,and the porous Ru-doped Co_(3)O_(4)/rGO(Ru-Co_(3)O_(4)/rGO)composite electrocatalyst was prepared by annealing.The phase structure,morphology,and valence state of the catalyst were analyzed by X-ray powder diffraction(XRD),scanning electron microscope(SEM),transmission electron microscopy(TEM),and X-ray photoelectron spectroscopy(XPS).In 1 mol·L^(-1)KOH,the oxygen evolution reaction(OER)performance of the catalyst was measured by linear sweep voltammetry,cyclic voltammetry,and chronoamperometry.The results show that the combination of Ru doping and rGO provides a fast channel for collaborative electron transfer.At the same time,rGO as a carbon carrier can improve the electrical conductivity of Ru-Co_(3)O_(4)particles,and the uniformly dispersed nanoparticles enable the reactants to diffuse freely on the catalyst.The results showed that the electrochemical performance of Ru-Co_(3)O_(4)/rGO was much better than that of Co_(3)O_(4)/rGO,and the overpotential of Ru-Co_(3)O_(4)/rGO was 363.5 mV at the current density of 50 mA·cm^(-2).

Prediction of microstructure evolution of ZK61 alloy during hot spinning by internal state variable model

An internal state variable(ISV)model was established according to the experimental results of hot plane strain compression(PSC)to predict the microstructure evolution during hot spinning of ZK61 alloy.The effects of the internal variables were considered in this ISV model,and the parameters were optimized by genetic algorithm.After validation,the ISV model was used to simulate the evolution of grain size(GS)and dynamic recrystallization(DRX)fraction during hot spinning via Abaqus and its subroutine Vumat.By comparing the simulated results with the experimental results,the application of the ISV model was proven to be reliable.Meanwhile,the strength of the thin-walled spun ZK61 tube increased from 303 to 334 MPa due to grain refinement by DRX and texture strengthening.Besides,some ultrafine grains(0.5μm)that played an important role in mechanical properties were formed due to the proliferation,movement,and entanglement of dislocations during the spinning process.

Operational optimization of copper flotation process based on the weighted Gaussian process regression and index-oriented adaptive differential evolution algorithm

Concentrate copper grade(CCG)is one of the important production indicators of copper flotation processes,and keeping the CCG at the set value is of great significance to the economic benefit of copper flotation industrial processes.This paper addresses the fluctuation problem of CCG through an operational optimization method.Firstly,a density-based affinity propagationalgorithm is proposed so that more ideal working condition categories can be obtained for the complex raw ore properties.Next,a Bayesian network(BN)is applied to explore the relationship between the operational variables and the CCG.Based on the analysis results of BN,a weighted Gaussian process regression model is constructed to predict the CCG that a higher prediction accuracy can be obtained.To ensure the predicted CCG is close to the set value with a smaller magnitude of the operation adjustments and a smaller uncertainty of the prediction results,an index-oriented adaptive differential evolution(IOADE)algorithm is proposed,and the convergence performance of IOADE is superior to the traditional differential evolution and adaptive differential evolution methods.Finally,the effectiveness and feasibility of the proposed methods are verified by the experiments on a copper flotation industrial process.

Geochemistry and petrogenesis of magnesian high-K granitoids from Bundelkhand Craton,Central India:New insights into crustal evolution

Background The Bundelkhand Craton is significant for preserving the multiphase granitoids magmatism from Paleoarchean to Neoarchean periods.It consists of a variety of granite rocks,including TTGs,sanukitoids,and high-K granitoids.This study presents geochemical characteristics of high-silica(68.97 wt.%–73.99 wt.%),low-silica(58.73wt.%–69.94 wt.%),and high K_(2)O(2.77 wt.%–6.16 wt.%)contents of granitoids.Objective The data on Bundelkhand Craton’s granitic magmatism and geodynamics is not sufficiently robust.Geochemical data from this study will be used to further understand the origin,source,and petrogenesis of granitoid rocks and their implications for the evolution of geodynamics.Methodology Twenty-one samples were collected and analyzed for major,trace,and REE elements.Major elements were measured using X-ray fluorescence spectrometry(XRF),and trace and REE elements were analyzed by ICP-MS.Standard procedures from the Geological Survey of India were followed.Results The geochemical analysis presents high-silica(68.97-73.99 wt.%),low-silica(58.73-69.94 wt.%),and high K2O(2.77-6.16 wt.%)contents in granitoids,classified as granite-granodiorite.The rocks are calcic to calcalkalic,magnesian,and range from peraluminous to metaluminous composition.REE patterns showed strong LREE enrichment relative to HREEs,with prominent negative Eu anomalies corresponding to earlier plagioclase fractionation.Multi-element patterns revealed negative anomalies in Nb,Sr,P,and Ti and positive anomalies in Pb.Conclusion The geochemical signatures attributed to the post-collisional magma generation and continental crustal contamination.The studied rocks show A-type and A2-type lineage,suggesting they originated from the melting of continental crust during transitional/post-collisional tectonic activity.The formation of hybrid granitoids in the Bundelkhand Craton is connected to the fractionation of hybrid magmas in shallow-seated magma chambers during these tectonic processes.

Aerodynamic instability evolution of a multi-stage combined compressor

Unstable operating conditions such as surge could cause damage to both aerodynamic performance and structural integrity of a compression system.This paper addresses the critical issue of aerodynamic instability in compressor design,particularly focusing on an axial-centrifugal combined compressor,a widely used yet underexplored configuration.An experimental investigation was conducted on a three-stage axial and one-stage centrifugal compressor(3A1C),using two pipe systems and employing fast-responding transducers to capture the dynamic instability process from choke condition to deep surge.Results reveal that at the design speed,3A1C enters deep surge directly,whereas at off-design speeds,it experiences rotating stall and mild surge across a wide mass flow range.Some special instability features in the combined compressor can be found in the steady state map and dynamic process.The characteristic curve of the first axial stage keeps a positive slope during the whole mass flow range at an off-design speed.The first stage could work stably on the stall characteristic curve because the centrifugal stage has stronger pressurization and plays a dominant role in global aerodynamic instability.Besides,rotating instability occurs at the first rotor tip and disappears as the back pressure increases,which is also rarely seen in a single-axial compressor.This is also related to the strong pressurization of the centrifugal stage.The findings of this paper will contribute to the understanding of aerodynamic instabilities in combined compressors.

Research progress in friction stir processing of magnesium alloys and their metal matrix surface composites: Evolution in the 21^(st )century

Rising concerns about climate change drive the demand for lightweight components.Magnesium(Mg)alloys are highly valued for their low weight,making them increasingly important in various industries.Researchers focusing on enhancing the characteristics of Mg alloys and developing their Metal Matrix Composites(MMCs)have gained significant attention worldwide over the past decade,driven by the global shift towards lightweight materials.Friction Stir Processing(FSP)has emerged as a promising technique to enhance the properties of Mg alloys and produce Mg-MMCs.Initially,FSP adapted to refine grain size from the micro to the nano level and accelerated the development of MMCs due to its solid-state nature and the synergistic effects of microstructure refinement and reinforcement,improving strength,hardness,ductility,wear resistance,corrosion resistance,and fatigue strength.However,producing defect-free and sound FSPed Mg and Mg-MMCs requires addressing several variables and their interdependencies,which opens up a broad range of practical applications.Despite existing reviews on individual FSP of Mg,its alloys,and MMCs,an attempt has been made to analyze the latest research on these three aspects collectively to enhance the understanding,application,and effectiveness of FSP for Mg and its derivatives.This review article discusses the literature,classifies the importance of Mg alloys,provides a historical background,and explores developments and potential applications of FSPed Mg alloys.It focuses on novel fabrication methods,reinforcement strategies,machine and tool design parameters,material characterization,and integration with other methods for enhanced properties.The influence of process parameters and the emergence of defects are examined,along with specific applications in mono and hybrid composites and their microstructure evolution.The study identifies promising reinforcement materials and highlights research gaps in FSP for Mg alloys and MMCs production.It concludes with significant recommendations for further exploration,reflecting ongoing advancements in this field.

Microstructural evolution and hot tensile behavior of Mg−3Zn−0.5Zr alloy subjected to multi-pass friction stir processing

The microstructures and hot tensile behaviors of ZK30 alloys subjected to single-and multi-pass friction stir processing(FSP)were systematically investigated.Following single-pass FSP(S-FSP),coarse grains underwent refinement to 1−2μm,with a distinct basal texture emerging in the stir zone(SZ).Additionally,second-phase particles were fragmented,dispersed,and partially dissolved.Multi-pass FSP(M-FSP)further enhanced the homogeneity of the microstructure,reduced texture intensity differences,and decreased the fraction of second-phase particles by 50%.Both S-FSP and M-FSP SZs demonstrated superplasticity at strain rates below 1×10^(−3)s^(−1)and at temperatures of 250−350℃.The S-FSP SZ exhibited an elongation of 390%at 250℃and 1×10^(−4)s^(−1),while the M-FSP SZ achieved an elongation of 406%at 350℃and 1×10^(−3)s^(−1).The superplastic deformation of SZ was co-dominated by grain boundary sliding(GBS)and the solute-drag mechanism in S-FSP and mainly by GBS in M-FSP.

Analysis of System Value Evolution Trends of Energy Storage in Decarbonization Process

With the continuous expansion of the scale of renewable energy installation,the demand for energy storage has increased significantly.However,there are significant differences in the value of energy storage in different scenarios,and the phenomenon of diminishing marginal benefits of energy storage is becoming more apparent.Therefore,themulti-dimensional value evolution trend of energy storage has become a key issue.This study selects indicators from three dimensions of energy storage:low-carbon emission reduction,smoothing wind and solar power fluctuations,and saving generation costs,quantifying the economic,environmental,and technical values of energy storage.This forms a quantitative evaluation system for energy storage value.By comparing the calculated system values under different energy storage capacities,the marginal value evolution trend of energy storage is obtained.Meanwhile,considering factors such as the utilization rate of renewable energy,the change in energy storage value under different scenarios is analyzed.The results show that the value of long-duration energy storage is significantly affected by the energy storage capacity.Specifically,when the charge-discharge efficiency of longduration energy storage reaches 0.6 or above,the system value increases significantly.Additionally,appropriately reducing the cost of energy storage capacity also helps to improve its system value.

Tectonic modes of mantle convection and their implications for Earth's tectonic evolution based on three-dimensional numerical simulations

Five tectonic modes of mantle convection are obtained and analyzed with three-dimensional numerical models in a spherical shell domain.The five tectonic convective modes are non-plate mobile-lid,plate-like mobile-lid,episodic plate-like mobile-lid,episodic stagnant-lid,and stagnant-lid convective modes,respectively.The typical characteristics of these five tectonic modes and their numerical classification criteria based on plateness,mobility,and their standard deviations are presented and discussed.The results show that the yield stress of the lithosphere has profound effects on the tectonic convective modes.With the gradual increase of yield stress,the tectonic mode of mantle convection changes from one to another sequentially through the aforementioned five modes.Additionally,as the Rayleigh number increases,the range of yield stress for the platelike mobile-lid convective mode decreases,and the dimensionless transition stress between different tectonic modes increases.Specifically,the dimensional transition stress between the non-plate mobile-lid convective mode and plate-like mobile-lid convective mode increases with the increase of Rayleigh number,but decreases between other tectonic modes.Furthermore,we find that the transition stress between different tectonic modes is inversely proportional to the internal heating rate,with the transition stress decreasing as the internal heating rate increases.The fitting analysis of the transition stress between tectonic modes shows that Earth's current plate tectonics correspond to a lithospheric yield stress of 150–250 MPa,which aligns with the strength of serpentinized mantle rock determined by experimental petrography.If the Archean mantle was 300℃warmer than it is today,then the Earth was in an episodic stagnant-lid convective mode.The tectonic evolution of the Earth's surface is closely related to the lithospheric strength and the process of thermal evolution.If the lithospheric strength was only 150 MPa,plate tectonics in the early mantle rapid cooling model would have begun before 3.8 Ga,and plate tectonics in the late mantle rapid cooling model would have begun at approximately 1.5 Ga.However,at a lithospheric strength of 200 MPa,plate tectonics in the late mantle rapid cooling model would have begun later than 0.95 Ga,and plate tectonics in the early mantle rapid cooling model would have begun at approximately 2 Ga.The early Earth was in the episodic stagnant-lid convective mode,which means that subduction might still have occurred at that time.The presence of the episodic plate-like mobile-lid convective mode in Earth's later history indicates that there might also have been intermittent surface stagnation during plate tectonics,which may provide an explanation for the quiet period of tectonic activity at approximately 1.0 Ga on Earth.This indicates that tectonic inactivity during a geological period is not an indicator that plate tectonics did not begin.

Mesozoic multi-direction collision tectonic evolution of the Ordos Basin, China: Insights from the detrital zircon and apatite (U-Th)/He analyses

The Ordos Basin(OB)in the western part of the North China Craton(NCC),was located at the jointed area of multi-plates and has recorded the Mesozoic tectonic characteristics.Its tectonic evolution in the Mesozoic is significant to understand the tectonic transformation of the northern margin of the NCC.In this work,the detrital zircon and apatite(U-Th)/He chronological system were analyzed in the northern part of the OB,and have provided new evidence for the regional tectonic evolution.The(U-Th)/He chronological data states the weighted ages of 240‒235 Ma,141 Ma with the peak distribution of 244 Ma,219 Ma,173 Ma,147‒132 Ma.The thermal evolution,geochronological data,and regional unconformities have proved four stages of regional tectonic evolution for the OB and its surroundings in the Mesozoic:(1)The Late Permian-Early Triassic;(2)the Late Triassic-Early Jurassic;(3)the Late Jurassic-Early Cretaceous;(4)the Late Cretaceous-Early Paleogene.It is indicated that the multi-directional convergence from the surrounding tectonic units has controlled the Mesozoic tectonic evolution of the OB.Four-stage tectonic evolution reflected the activation or end of different plate movements and provided new time constraints for the regional tectonic evolution of the NCC in the Mesozoic.

Solidification process and microstructure evolution of bulk undercooled Co-Sn alloys

A series of Co-Sn alloys with Sn content ranging from 12% to 32%（mole fraction） were undercooled to different degrees below the equilibrium liquidus temperature and the solidification behaviors were investigated by monitoring the temperature recalescence and examing the solidification microstructures.A boundary clearly exists,which separates the coupled growth zone from the decoupled growth zone of eutectic phases for the alloys with Sn content ranging from 14% to 31%（mole fraction）.The other Co-Sn alloys out of this content range are hard to be undercooled into the coupled growth zone in the experiment.It is found that the so-called non-reciprocal nucleation phenomenon does not happen in the solidification of undercooled Co-Sn off-eutectic alloys.

Microstructure evolution in cooling process of Al-Zn-Mg-Cu alloy and kinetics description

The microstructure evolution of Al-Zn-Mg-Cu alloy was studied by differential scanning calorimetry （DSC） and transmission electron microscopy （TEM） during different rate cooling processes. Based on the DSC results, the kinetics analysis was carried out. The results indicate that the precipitation of η phase is the predominant transformation for the alloy during the cooling process after the solution treatment. And the η phase nucleates on dispersoids and at grain boundaries. The amount of η phase decreases with increasing cooling rate, and reduces by 75% as the cooling rate increases from 5 to 50 ℃/min. The kinetics of the precipitation of η phase can be described by the Kamamoto transformation model when the cooling rate is a constant.

Influence of thermomechanical processing on microstructure,texture evolution and mechanical properties of Al-Mg-Si-Cu alloy sheets

Influence of thermomechanical processing on the microstructure, texture evolution and mechanical properties of A1-Mg-Si-Cu alloy sheets was studied systematically. The quite weak mechanical properties anisotropy was obtained in the alloy sheet through thermomechanical processing optimizing. The highly elongated microstmcture is the main structure for the hot or cold-rolled alloy sheets. H {001 } （110） and E { 111 } （110） are the main texture components in the surface layer of hot-rolled sheet, while ]/-fibre is dominant in quarter and center layers. Compared with the hot-rolled sheet, the intensities offl-fibre components are higher after the first cold rolling, but H {001 }（110） component in the surface layer decreases greatly. Almost no deformation texatre can be observed after intermediate annealing. And fl-fibre becomes the main texture again after the final cold rolling. With the reduction of the thickness, the through-thickness texture gradients become much weaker. The through-thickness recrystallization texture in the solution treated sample only has cubeyD {001 }（310） component. The relationship among thermomechanical processing, microstructure, texture and mechanical orouerties was analyzed.

Application of novel physical picture based on artificial neural networks to predict microstructure evolution of Al-Zn-Mg-Cu alloy during solid solution process

The effects of the solid solution conditions on the microstructure and tensile properties of Al?Zn?Mg?Cu aluminum alloy were investigated by in-situ resistivity measurement, optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and tensile test. A radial basis function artificial neural network (RBF-ANN) model was developed for the analysis and prediction of the electrical resistivity of the tested alloy during the solid solution process. The results show that the model is capable of predicting the electrical resistivity with remarkable success. The correlation coefficient between the predicted results and experimental data is 0.9958 and the relative error is 0.33%. The predicted data were adopted to construct a novel physical picture which was defined as “solution resistivity map”. As revealed by the map, the optimum domain for the solid solution of the tested alloy is in the temperature range of 465?475 °C and solution time range of 50?60 min. In this domain, the solution of second particles and the recrystallization phenomenon will reach equilibrium.