This paper aims to design a special exchanger to recover the exhaust gas heat of marine diesel engines used in small and medium-sized fishing vessels,which can then be used to heat water up to 55°C–85°C for...This paper aims to design a special exchanger to recover the exhaust gas heat of marine diesel engines used in small and medium-sized fishing vessels,which can then be used to heat water up to 55°C–85°C for membrane desalination devices to produce fresh water.A new exhaust-gas heat exchanger of fins and tube,with a reinforced heat transfer tube section,unequal spacing fins,a mixing zone between the fin groups and four routes tube bundle,was designed.Numerical simulations were also used to provide reference information for structural design.Experiments were carried out for exhaust gas waste heat recovery from a marine diesel engine in an engine test bench utilizing the heat exchanger.The experimental results show that the difference between heat absorption by water and heat reduction of exhaust gas is less than 6.5%.After the water flow rate was adjusted,the exhaust gas waste heat recovery efficiency was higher than 70%,and the exhaust-gas heat exchanger’s outlet water temperature was 55°C–85°C at different engine loads.This means that the heat recovery from the exhaust gas of a marine diesel engine meets the requirement to drive a membrane desalination device to produce fresh water for fishers working in small and medium-sized fishing vessels.展开更多
Diesel engines meeting the latest emission regulations must be equipped with exhaust gas aftertreatment system,including diesel oxidation catalysts(DOC),diesel particulate filters(DPF),and selective catalytic reductio...Diesel engines meeting the latest emission regulations must be equipped with exhaust gas aftertreatment system,including diesel oxidation catalysts(DOC),diesel particulate filters(DPF),and selective catalytic reduction(SCR).However,before the final integration of the aftertreatment system(DOC+DPF+SCR)and the diesel engine,a reasonable structural optimization of the catalytic converters and a large number of bench calibration tests must be completed,involving large costs and long development cycles.The design and optimization of the exhaust gas aftertreatment system for a heavy-duty diesel engine was proposed in this paper.Firstly,one-dimensional(1D)and threedimensional(3D)computational models of the exhaust gas aftertreatment system accounting for the structural parameters of the catalytic converters were established.Then based on the calibrated models,the effects of the converter’s structural parameters on their main performance indicators,including the conversion of various exhaust pollutants and the temperatures and pressure drops of the converters,were studied.Finally,the optimal design scheme was obtained.The temperature distribution of the solid substrates and pressure distributions of the catalytic converters were studied based on the 3D model.The method proposed in this paper has guiding significance for the optimization of diesel engine aftertreatment systems.展开更多
Exhaust waste heat recovery system based on organic Rankine cycle(ORC)has been considered as an effective method to achieve energy conservation and emissions reduction of engine.The performance of adiesel engine with ...Exhaust waste heat recovery system based on organic Rankine cycle(ORC)has been considered as an effective method to achieve energy conservation and emissions reduction of engine.The performance of adiesel engine with an on-board ORC exhaust heat recovery system was evaluated through simulations in this study.The combined system was optimized through controlling the exhaust gas mass flow rate entering the ORC system.The models of the engine with ORC system were developed in GT-suite and Simulink environment.The validation results showed high accuracy of the models.The performance of the system recovering heat from different exhaust gas mass flow rates was evaluated.The comparative analysis of the performance between the optimized and un-optimized system was also presented.The results indicated that the exhaust gas mass flow rate had significant effects on the system performance.Integration with the onboard ORC system could effectively improve the engine power performance.The power output of the engineORC combined system with optimization had further improvement,and the maximum improvement could reach up to 1.16 kW.展开更多
In the condition of constant speed and light load, an experimental study of a turbocharged and intercooled diesel engine with exhaust gas recirculation （EGR） system focuses on the influence of different EGR rates on...In the condition of constant speed and light load, an experimental study of a turbocharged and intercooled diesel engine with exhaust gas recirculation （EGR） system focuses on the influence of different EGR rates on combustion process, dynamic performance, economic performance and emission performance of a diesel engine. With the increase of EGR rate, the oxygen concentration of the intake-side decreases, the fuel air equivalence ratio increases, and the maximum explosion pressure in the cylinder decreases. Meanwhile, the average temperature in the cylinder drops, the ignition delay is prolonged, the ignition timing delays, and the maximum heat release rate decreases. The increase of EGR rate makes NOx emissions decrease obviously and continue to decline. When EGR is low, the smoke rate enlarges slowly with the increase of EGR rate, and enlarges greatly at the rate higher than 43% and reaches the maximum at the rate of 57%. When EGR rate is higher than 61%, the smoke rate drops rapidly, and the content of CO and hydrocarbon （HC） increases rapidly with high EGR rate.展开更多
采用柠檬酸络合燃烧法制备了纳米钙钛矿型复合氧化物 AMnO_3(A 为 La,Ce,Pr,Nd)和 La_(0.8)M_(0.2)MnO_3(M 为 K,Cs,Sr)催化剂。采用 X 射线衍射、H_2-程序升温还原和扫描电子显微镜等方法对催化剂试样进行了表征,利用程序升温反应评价...采用柠檬酸络合燃烧法制备了纳米钙钛矿型复合氧化物 AMnO_3(A 为 La,Ce,Pr,Nd)和 La_(0.8)M_(0.2)MnO_3(M 为 K,Cs,Sr)催化剂。采用 X 射线衍射、H_2-程序升温还原和扫描电子显微镜等方法对催化剂试样进行了表征,利用程序升温反应评价了催化剂用于同时消除柴油机尾气中炭颗粒和 NO 的催化活性。研究结果表明,A 位阳离子种类及 A 位掺杂离子的种类对催化剂的活性都有影响。A 位离子为 La 的催化剂(LaMnO_3)活性最好;用低价金属离子部分取代 A 位离子,催化剂活性得到改善,其中以K离子取代效果最好;LaMnO_3和 La_(0.8)K_(0.2)MnO_3催化剂的炭颗粒燃烧温度范围分别为321～521℃和311～425℃,NO 的转化率分别为7.6%和16.4%。展开更多
基金supported by the National Key Research and Development Program of China[Grant No.2017YFE0116100]the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China[Grant No.KYCX20_2821].
文摘This paper aims to design a special exchanger to recover the exhaust gas heat of marine diesel engines used in small and medium-sized fishing vessels,which can then be used to heat water up to 55°C–85°C for membrane desalination devices to produce fresh water.A new exhaust-gas heat exchanger of fins and tube,with a reinforced heat transfer tube section,unequal spacing fins,a mixing zone between the fin groups and four routes tube bundle,was designed.Numerical simulations were also used to provide reference information for structural design.Experiments were carried out for exhaust gas waste heat recovery from a marine diesel engine in an engine test bench utilizing the heat exchanger.The experimental results show that the difference between heat absorption by water and heat reduction of exhaust gas is less than 6.5%.After the water flow rate was adjusted,the exhaust gas waste heat recovery efficiency was higher than 70%,and the exhaust-gas heat exchanger’s outlet water temperature was 55°C–85°C at different engine loads.This means that the heat recovery from the exhaust gas of a marine diesel engine meets the requirement to drive a membrane desalination device to produce fresh water for fishers working in small and medium-sized fishing vessels.
基金Projects(2017YFC0211202,2017YFC0211301)supported by the National Key R&D Program of China。
文摘Diesel engines meeting the latest emission regulations must be equipped with exhaust gas aftertreatment system,including diesel oxidation catalysts(DOC),diesel particulate filters(DPF),and selective catalytic reduction(SCR).However,before the final integration of the aftertreatment system(DOC+DPF+SCR)and the diesel engine,a reasonable structural optimization of the catalytic converters and a large number of bench calibration tests must be completed,involving large costs and long development cycles.The design and optimization of the exhaust gas aftertreatment system for a heavy-duty diesel engine was proposed in this paper.Firstly,one-dimensional(1D)and threedimensional(3D)computational models of the exhaust gas aftertreatment system accounting for the structural parameters of the catalytic converters were established.Then based on the calibrated models,the effects of the converter’s structural parameters on their main performance indicators,including the conversion of various exhaust pollutants and the temperatures and pressure drops of the converters,were studied.Finally,the optimal design scheme was obtained.The temperature distribution of the solid substrates and pressure distributions of the catalytic converters were studied based on the 3D model.The method proposed in this paper has guiding significance for the optimization of diesel engine aftertreatment systems.
文摘Exhaust waste heat recovery system based on organic Rankine cycle(ORC)has been considered as an effective method to achieve energy conservation and emissions reduction of engine.The performance of adiesel engine with an on-board ORC exhaust heat recovery system was evaluated through simulations in this study.The combined system was optimized through controlling the exhaust gas mass flow rate entering the ORC system.The models of the engine with ORC system were developed in GT-suite and Simulink environment.The validation results showed high accuracy of the models.The performance of the system recovering heat from different exhaust gas mass flow rates was evaluated.The comparative analysis of the performance between the optimized and un-optimized system was also presented.The results indicated that the exhaust gas mass flow rate had significant effects on the system performance.Integration with the onboard ORC system could effectively improve the engine power performance.The power output of the engineORC combined system with optimization had further improvement,and the maximum improvement could reach up to 1.16 kW.
基金Supported by the Major Plan Projects of Science and Technology of Jiangxi Provincial Department of Education(GJJ151145)the Youth Science Fund Project Science and Technology of Jiangxi Provincial Department of Science and Technology(20114BAB216002)the Plan Projects of Science and Technology of Jiangxi Provincial Department of Science and Technology(2016BBE50074)
文摘In the condition of constant speed and light load, an experimental study of a turbocharged and intercooled diesel engine with exhaust gas recirculation （EGR） system focuses on the influence of different EGR rates on combustion process, dynamic performance, economic performance and emission performance of a diesel engine. With the increase of EGR rate, the oxygen concentration of the intake-side decreases, the fuel air equivalence ratio increases, and the maximum explosion pressure in the cylinder decreases. Meanwhile, the average temperature in the cylinder drops, the ignition delay is prolonged, the ignition timing delays, and the maximum heat release rate decreases. The increase of EGR rate makes NOx emissions decrease obviously and continue to decline. When EGR is low, the smoke rate enlarges slowly with the increase of EGR rate, and enlarges greatly at the rate higher than 43% and reaches the maximum at the rate of 57%. When EGR rate is higher than 61%, the smoke rate drops rapidly, and the content of CO and hydrocarbon （HC） increases rapidly with high EGR rate.
文摘采用柠檬酸络合燃烧法制备了纳米钙钛矿型复合氧化物 AMnO_3(A 为 La,Ce,Pr,Nd)和 La_(0.8)M_(0.2)MnO_3(M 为 K,Cs,Sr)催化剂。采用 X 射线衍射、H_2-程序升温还原和扫描电子显微镜等方法对催化剂试样进行了表征,利用程序升温反应评价了催化剂用于同时消除柴油机尾气中炭颗粒和 NO 的催化活性。研究结果表明,A 位阳离子种类及 A 位掺杂离子的种类对催化剂的活性都有影响。A 位离子为 La 的催化剂(LaMnO_3)活性最好;用低价金属离子部分取代 A 位离子,催化剂活性得到改善,其中以K离子取代效果最好;LaMnO_3和 La_(0.8)K_(0.2)MnO_3催化剂的炭颗粒燃烧温度范围分别为321～521℃和311～425℃,NO 的转化率分别为7.6%和16.4%。
