PREPARATION OF HIGH THERMAL EXPANSION COEFFICIENT PORCELAINS FUSED TO METALS

Usually the thermal expansion coefficients (TEC) of metals are higher than that of porcelains. In order to match the TECs in the case of coating porcelains on metals, high TEC porcelains are needed. In this research, the high TEC phase leucite (KAlSi2 O6) in the high TEC porcelain was prepared by sol-gel method. The crystal size of leucite made by sol-gel is about 77nm through controlling the process parameters. The process from xerogel to leucite was investigated by means of DSC (differential scanning calorimetry), TG (thermogravimetry), XRD ( X-ray diffraction) and IR (infrared absorption spectrum). Leucite had been detected after the gel was treated at 900℃, this formation temperature is about 250℃ lower than that of melting method. The porcelain made from 50% of the leucite powder and 50% of low fused temperature frit has an average TEC of 19.2×10-6/℃ C from room temperature to 450℃, which is much higher than the common porcelains.

Preparation, Characterization and Thermal Expansion of Pr Co-Dopant in Samarium Doped Ceria

The compositions Ce0.8-xSm0.2O2-δ(X=0, 0.02, 0.04, 0.06) were prepared through the sol–gel route. The effect of Pr addition on the crystal structure, densification and thermal expansion of Ce0.8Sm0.2O2-δ was studied. The phase identification and morphology was studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). X-ray diffraction analysis showed that all the samples exhibit a fluorite structure. The lattice parameters? were determined by X-ray powder diffraction. Lattice parameters and volume of the unit cell increases with Pr doping. Density of the all samples is more than 90% of theoretical density. The thermal expansion was measured using dilatometric technique in the temperature range 30–1000°C. It was observed that the thermal expansion increased linearly with increasing temperature for all the samples.

EFFECT OF PREPARATION CONDITION ON THERMAL EXPANSION ANISOTROPY FOR AMORPHOUS Fe_(78)B_(13)Si_9 ALLOY

The thermal expansion along the longitudinal and transverse directions for amorphous Fe_(78)B_(13)Si_9 alloy prepared under various preparing conditions were investigated.The thermal expansion anisotropy appears in all specimens.The expansion along the longitudinal direction is less than that along the transverse direction.The cooling rate,the melt temperature before jet casting and the cycling temperature affect the thermal expansion coefficients and anisotropy.The amisotropy of thermal expansion originates from the orientation of atomic interaction force,the atomic oscillatory frequency and short range order structure or the directional arrangement of defects in the alloy.

Preparation and Characteristic of Glass-Ceramics with Super Low Thermal Expansion Coefficient

The preparation technics of glass-ceramics with super low coefficient of thermal expansion containing β-quartz solid solution as a main crystal phase based on the glass in the system Li2O-Al2O3-SiO2 was introduced. The composition of base glass, technics of melting and heat treatment effecting on characteristic of glass-ceramics was described. Specimens were prepared by melting, anneal and controlled two steps heat treatment. Crystal phase, microstructure and elementary distributing were studied by using XRD, SEM and EDS respectively. Prepared specimens show excellent transparency and super low thermal expansion coefficient of 2×10-8 ·K-1, which reaches international advanced level.

Expansion of human umbilical cord derived mesenchymal stem cells in regenerative medicine

BACKGROUND Stem cells are undifferentiated cells that possess the potential for self-renewal with the capacity to differentiate into multiple lineages.In humans,their limited numbers pose a challenge in fulfilling the necessary demands for the regeneration and repair of damaged tissues or organs.Studies suggested that mesenchymal stem cells(MSCs),necessary for repair and regeneration via transplantation,require doses ranging from 10 to 400 million cells.Furthermore,the limited expansion of MSCs restricts their therapeutic application.AIM To optimize a novel protocol to achieve qualitative and quantitative expansion of MSCs to reach the targeted number of cells for cellular transplantation and minimize the limitations in stem cell therapy protocols.METHODS Human umbilical cord(hUC)tissue derived MSCs were obtained and re-cultured.These cultured cells were subjected to the following evaluation pro-cedures:Immunophenotyping,immunocytochemical staining,trilineage differentiation,population doubling time and number,gene expression markers for proliferation,cell cycle progression,senescence-associatedβ-galactosidase assay,human telomerase reverse transcriptase(hTERT)expression,mycoplasma,cytomegalovirus and endotoxin detection.RESULTS Analysis of pluripotent gene markers Oct4,Sox2,and Nanog in recultured hUC-MSC revealed no significant differences.The immunophenotypic markers CD90,CD73,CD105,CD44,vimentin,CD29,Stro-1,and Lin28 were positively expressed by these recultured expanded MSCs,and were found negative for CD34,CD11b,CD19,CD45,and HLA-DR.The recultured hUC-MSC population continued to expand through passage 15.Proliferative gene expression of Pax6,BMP2,and TGFb1 showed no significant variation between recultured hUC-MSC groups.Nevertheless,a significant increase(P<0.001)in the mitotic phase of the cell cycle was observed in recultured hUC-MSCs.Cellular senescence markers(hTERT expression andβ-galactosidase activity)did not show any negative effect on recultured hUC-MSCs.Additionally,quality control assessments consistently confirmed the absence of mycoplasma,cytomegalovirus,and endotoxin contamination.CONCLUSION This study proposes the development of a novel protocol for efficiently expanding stem cell population.This would address the growing demand for larger stem cell doses needed for cellular transplantation and will significantly improve the feasibility of stem cell based therapies.

Research Progress of Bowel Preparation for Colonoscopy

Colorectal cancer ranks third in the global cancer data in 2020. Colorectal scope is the most effective method to diagnose colorectal diseases such as benign and malignant colorectal tumors. The poor quality of intestinal preparation causes an increased rate of missed diagnosis of colorectal tumors, reduces the rate of cecal intubation for colorectal examination, increases the discomfort, and reduces the compliance of re-examination. Therefore, we should try our best to improve the quality of intestinal preparation. This study reviewed the latest advances related to the preoperative preparation for colonoscopy. Recent research shows that smartphone apps can provide more detailed education and guidance on bowel preparation;Pre-packaged foods are more suitable as a way to eat before colonoscopy. The use of smaller doses, better taste of cathartic agents, and some auxiliary measures, combined with the patient’s situation to provide personalized intestinal preparation measures to improve the quality of intestinal preparation. Starting from the quality of colonoscopy bowel preparation, continuous improvement of patients’ tolerance to bowel preparation, continuous improvement of bowel preparation plan based on individual factors’ needs, and better communication with examined subjects by using existing scientific information technology, may be the hot spot of colonoscopy bowel preparation research in the next few years.

Characterization, preparation, and reuse of metallic powders for laser powder bed fusion: a review

Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The printing quality and performance of L-PBF alloys are infuenced by numerous variables consisting of feedstock powders, manufacturing process,and post-treatment. As the starting materials, metallic powders play a critical role in infuencing the fabrication cost, printing consistency, and properties. Given their deterministic roles, the present review aims to retrospect the recent progress on metallic powders for L-PBF including characterization, preparation, and reuse. The powder characterization mainly serves for printing consistency while powder preparation and reuse are introduced to reduce the fabrication costs.Various powder characterization and preparation methods are presented in the beginning by analyzing the measurement principles, advantages, and limitations. Subsequently, the effect of powder reuse on the powder characteristics and mechanical performance of L-PBF parts is analyzed, focusing on steels, nickel-based superalloys, titanium and titanium alloys, and aluminum alloys. The evolution trends of powders and L-PBF parts vary depending on specific alloy systems, which makes the proposal of a unified reuse protocol infeasible. Finally,perspectives are presented to cater to the increased applications of L-PBF technologies for future investigations. The present state-of-the-art work can pave the way for the broad industrial applications of L-PBF by enhancing printing consistency and reducing the total costs from the perspective of powders.

Semi-analytical solution for drained expansion analysis of a hollow cylinder of critical state soils

The expansion of a thick-walled hollow cylinder in soil is of non-self-similar nature that the stress/deformation paths are not the same for different soil material points.As a result,this problem cannot be solved by the common self-similar-based similarity techniques.This paper proposes a novel,exact solution for rigorous drained expansion analysis of a hollow cylinder of critical state soils.Considering stress-dependent elastic moduli of soils,new analytical stress and displacement solutions for the nonself-similar problem are developed taking the small strain assumption in the elastic zone.In the plastic zone,the cavity expansion response is formulated into a set of first-order partial differential equations(PDEs)with the combination use of Eulerian and Lagrangian descriptions,and a novel solution algorithm is developed to efficiently solve this complex boundary value problem.The solution is presented in a general form and thus can be useful for a wide range of soils.With the new solution,the non-self-similar nature induced by the finite outer boundary is clearly demonstrated and highlighted,which is found to be greatly different to the behaviour of cavity expansion in infinite soil mass.The present solution may serve as a benchmark for verifying the performance of advanced numerical techniques with critical state soil models and be used to capture the finite boundary effect for pressuremeter tests in small-sized calibration chambers.

Swelling pressure evolution characterization of strong expansive soil considering the influence of reserved expansion deformation

Numerous engineering cases have demonstrated that the expansive soil channel slope remains susceptible to damage with the implementation of a rigid or closed protective structure. It is common for the protective structure to experience bulging failure due to excessive swelling pressure. To investigate the swelling pressure properties of expansive soil, the constant volume test was employed to study the influence of water content and reserved expansion deformation on the characteristics of swelling pressure in strong expansive soils, and also to explore the evolution mechanism of the swelling pressure. The findings demonstrate that the swelling pressure-time curve can be classified into swelling pressure-time softening and swelling pressure-time stability type. The swelling pressuretime curve of the specimen with low water content is the swelling pressure-time softening type, and the softening level will be weakened with increasing reserved expansion deformation. Besides, the maximum swelling pressure Psmax decreases with increasing water content and reserved expansion deformation, especially for expansion ratio η from 24% to 37%. The reserved deformation has little effect on reducing Psmax when it is beyond 7% of the expansion rate. The specimen with low water content has a more homogeneous structure due to the significant expansion-filling effect, and the fracture and reorganization of the aggregates in the specimens with low water content cause the swelling pressure-time softening behavior. In addition, the proposed swelling pressure-time curve prediction model has a good prediction on the test results. If necessary, a deformation space of about 7% expansion rate is recommended to be reserved in the engineering to reduce the swelling pressure except for keeping a stable water content.

On-spot preparation of EDTA solution for the treatment of band keratopathy:a case report

Dear Editor,We report a case of band keratopathy who experienced several ocular surgeries,secondary uveitis and glaucoma which eventually led to severe band keratopathy.We use commonly-used vacuum blood collection tubes with ethylenediaminetetraacetic acid dipotassium salt(EDTA-K2)to prepare chelation solution on-spot to remove the calcium deposits on the corneal surface.It is proved to be relatively safety,efficacy,cost-effective.

Common Artifacts and Remedies in Histological Preparations

The importance of the accuracy of preparing biological specimen as histological sections that can be examined under a microscope lies in reflecting a true image of the tissue that includes all its components, which are used in scientific research or for the purpose of diagnosing various diseases of the body. Despite this, some cellular structures within the tissue may suffer from some alterations that result from the appearance of defects during any stage of preparing these microscopic sections, which alter or interfere with the precise cellular structures and morphology that constitute the tissue and thus give a different image for tissue features and cause confusion in the work histopathologist in the diagnosis. There are several reasons that can cause a misdiagnosis of the sample that occurs during the surgical separation process or after separation during the stages of microscopic preparation techniques from fixation stage, tissue processing, embedding or microtomy, staining until mounting procedures. The constant need to identify these defects and their causes in addition to try to reduce them is one of the biggest challenges evident in pathology laboratories. Therefore, this study aims to review the most common defects that occur in any stage of tissue processing, with an explanation of their causes and appropriate ways to avoid them.

Preparation and Thermal Stability of AlMoON Based Solar Selective Absorption Coating

AlMoON based solar selective absorption coatings were deposited on stainless steel substrate by magnetron sputtering.The coatings included infrared reflection layer Mo,absorption layer AlMoN,absorption layer AlMoON and antireflection layer AlMoO from bottom to top.The surface of the deposited coatings is flat without obvious defects.The absorptivity and emissivity are 0.896 and 0.09,respectively,and the quality factor is 9.96.After heat treatment at 500℃-36 h,the surface roughness of the coating increases,a small number of cracks and other defects appear,and the broken part is still attached to the coating surface.A certain degree of element diffusion occurs in the coatings,resulting in the decline of the optical properties of the coatings.The absorptivity and emissivity are 0.883 and 0.131,respectively,the quality factor is 7.06,and the PC value is 0.0335.The coatings do not fail under this condition and have certain thermal stability.

Progress in preparation of AlN-reinforced magnesium matrix composites:A review

As a ceramic material,AlN has very good thermophysical and mechanical properties.In addition,AlN is an effective refining agent for Mg alloys because it has a lattice constant similar to that of Mg.Therefore,AlN is an ideal reinforcement for magnesium matrix composites(MMCs),and is attracting increasing attention.This review addresses the development of preparation technologies for AlN-reinforced Mg matrix composites.The mainstream preparation techniques include stir casting,melt infiltration,powder metallurgy,and in-situ methods.In addition,the advantages and disadvantages of these techniques are analyzed in depth,and it is pointed out that the next direction for the preparation of high-performance AlN-reinforced MMCs is less aluminization and multiple technologies integration.

Significant lake expansion has accelerated permafrost degradation on the Qinghai-Tibet Plateau

In recent years, lakes on the Qinghai-Tibet Plateau have become more responsive to climate change. In September 2011, Zonag Lake in Hoh Xil experienced sudden drainage, the water eventually flowed into Yanhu Lake, which caused Yanhu Lake to continue to expand. The potential collapse of Yanhu Lake could directly threaten the operational safety of the adjacent Qinghai-Tibet Highway, Qinghai-Tibet Railway. To explore the implications of expanding lakes on the surrounding permafrost, we selected Hoh Xil Yanhu Lake on the Qinghai-Tibet Plateau to study the effect of lake expansion on permafrost degradation. The permafrost degradation in the Yanhu Lake basin from October 2017 to December 2022 was inverted using Sentinel-1 satellite image data and small baseline subset interferometry synthetic aperture radar(SBAS-In SAR) technology. Additionally, permafrost degradation from February 2007 and February 2010 was analyzed using advanced land observing satellite phased array-type L-band synthetic aperture radar(ALOS PALSAR) satellite images and differential interferometric synthetic aperture radar(D-In SAR) technique. The results showed that the permafrost around Yanhu Lake experienced accelerated degradation. Prior to the expansion of Yanhu Lake, the average annual deformation rate along the line of sight(LOS) direction was 6.7 mm/yr. After the expansion, the rate increased to 20.9 mm/yr. The integration of spatial-temporal distribution maps of surface subsidence, Wudaoliang borehole geothermal data, meteorological data, Yanhu Lake surface area changes, and water level changes supports the assertion that the intensified permafrost degradation could be attributed to lake expansion rather than the rising air temperature. Furthermore, permafrost degradation around Yanhu Lake could impact vital infrastructure such as the adjacent Qinghai-Tibet Highway and Qinghai-Tibet Railway.

Preparation of single atom catalysts for high sensitive gas sensing

Single atom catalysts(SACs)have garnered significant attention in the field of catalysis over the past decade due to their exceptional atom utilization efficiency and distinct physical and chemical properties.For the semiconductor-based electrical gas sensor,the core is the catalysis process of target gas molecules on the sensitive materials.In this context,the SACs offer great potential for highly sensitive and selective gas sensing,however,only some of the bubbles come to the surface.To facilitate practical applications,we present a comprehensive review of the preparation strategies for SACs,with a focus on overcoming the challenges of aggregation and low loading.Extensive research efforts have been devoted to investigating the gas sensing mechanism,exploring sensitive materials,optimizing device structures,and refining signal post-processing techniques.Finally,the challenges and future perspectives on the SACs based gas sensing are presented.

Research on the Generation Mechanism and Suppression Method of Aerodynamic Noise in Expansion Cavity Based on Hybrid Method

The expansion chamber serves as the primary silencing structure within the exhaust pipeline.However,it can also act as a sound-emitting structure when subjected to airflow.This article presents a hybrid method for numerically simulating and analyzing the unsteady flow and aerodynamic noise in an expansion chamber under the influence of airflow.A fluid simulation model is established,utilizing the Large Eddy Simulation(LES)method to calculate the unsteady flow within the expansion chamber.The simulation results effectively capture the development and changes of the unsteady flow and vorticity inside the cavity,exhibiting a high level of consistency with experimental observations.To calculate the aerodynamic noise sources within the cavity,the flow field results are integrated using the method of integral interpolation and inserted into the acoustic grid.The acoustic analogy method is then employed to determine the aerodynamic noise sources.An acoustic simulation model is established,and the flow noise source is imported into the sound field grid to calculate the sound pressure at the far-field response point.The calculated sound pressure levels and resonance frequencies show good agreement with the experimental results.To address the issue of airflow regeneration noise within the cavity,perforated tubes are selected as a means of noise suppression.An experimental platformfor airflow regeneration noise is constructed,and experimental samples are processed to analyze and verify the noise suppression effect of perforated tube expansion cavities under different airflow velocities.The research findings indicate that the perforated tube expansion cavity can effectively suppress low-frequency aerodynamic noise within the cavity by impeding the formation of strong shear layers.Moreover,the semi-perforated tube expansion cavity demonstrates the most effective suppression of aerodynamic noise.

Stochastic programming based coordinated expansion planning of generation,transmission,demand side resources,and energy storage considering the DC transmission system

With the increasing penetration of wind and solar energies,the accompanying uncertainty that propagates in the system places higher requirements on the expansion planning of power systems.A source-grid-load-storage coordinated expansion planning model based on stochastic programming was proposed to suppress the impact of wind and solar energy fluctuations.Multiple types of system components,including demand response service entities,converter stations,DC transmission systems,cascade hydropower stations,and other traditional components,have been extensively modeled.Moreover,energy storage systems are considered to improve the accommodation level of renewable energy and alleviate the influence of intermittence.Demand-response service entities from the load side are used to reduce and move the demand during peak load periods.The uncertainties in wind,solar energy,and loads were simulated using stochastic programming.Finally,the effectiveness of the proposed model is verified through numerical simulations.

The Negative Thermal Expansion Property of NdMnO_(3) Based on Pores Effect and Phase Transition

A novel negative thermal expansion(NTE) material NdMnO_(3) was synthesized by solid-state method at 1 523 K. The crystal structure, phase transition, pores effect and negative expansion properties of NdMnO_(3) were investigated by variable temperature X-ray diffraction(XRD), scanning electron microscope(SEM) and variable temperature Raman spectra. The compound exhibits NTE properties in the orderly O' phase crystal structure. When the temperature is from 293 to 759 K, the ceramic NdMnO_(3) shows negative thermal expansion of-4.7×10^(-6)/K. As temperature increases, the ceramic NdMnO_(3) presents NTE property range from 759 to 1 007 K. The average linear expansion coefficient is-18.88×10^(-6)/K. The physical mechanism of NTE is discussed and clarified through experiments.

Deformation mechanisms and microstructural characteristics of AZ61 magnesium alloys processed by a continuous expansion extrusion approach

The unique continuous extrusion-based severe plastic deformation approaches were proposed recently to process high-performance magnesium (Mg) alloys,while the in-depth deformation mechanisms under such complicated thermomechanical conditions were not well understood In the present work,the fundamental deformation behaviors of AZ61 Mg alloy from 25 to 400°C were firstly examined under uniaxial compression deformation.Then the deformation mechanisms and microstructural characteristics of AZ61 Mg alloy during continuous expansion extrusion forming (CEEF) were systematically investigated by microstructural observations,finite element and cellular automata simulations The results showed that the continuous evolutions of temperature,larger strain level and complex stress state with strain rate range of 0~5.98 s-1during CEEF brought the distinctive dynamic recrystallization behaviors and texture development in AZ61 Mg alloy,which were different to that of uniaxial compression deformation.In details,a remarkable grain refinement was achieved via CEEF processing due to the simultaneous actions of continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX).Gradually enhanced CDRX were observed from center to edge region,which had significant effects on the texture distribution and texture strength.The c-axis of most grains rotated under distinctive shear strain following parabolic metal flow,resulting in stable fiber texture.In addition,the evolution of the internal texture of the alloy led to an obvious increase in the Schmid factor for the activation of basal(c+a)slip system.©2022 Chongqing University.Publishing services provided by Elsevier B.V.on behalf of Ke Ai Communications Co.Ltd.