Experimental investigation on coal pore-fracture variation and fractal characteristics synergistically affected by solvents for improving clean gas extraction

Chemical solvents instead of pure water being as hydraulic fracturing fluid could effectively increase permeability and improve clean methane extraction efficiency.However,pore-fracture variation features of lean coal synergistically affected by solvents have not been fully understood.Ultrasonic testing,nuclear magnetic resonance analysis,liquid phase mass spectrometry was adopted to comprehensively analyze pore-fracture change characteristics of lean coal treated by combined solvent(NMP and CS_(2)).Meanwhile,quantitative characterization of above changing properties was conducted using geometric fractal theory.Relationship model between permeability,fractal dimension and porosity were established.Results indicate that the end face fractures of coal are well developed after CS2and combined solvent treatments,of which,end face box-counting fractal dimensions range from 1.1227 to 1.4767.Maximum decreases in ultrasonic longitudinal wave velocity of coal affected by NMP,CS_(2)and combined solvent are 2.700%,20.521%,22.454%,respectively.Solvent treatments could lead to increasing amount of both mesopores and macropores.Decrease ratio of fractal dimension Dsis 0.259%–2.159%,while permeability increases ratio of NMR ranges from 0.1904 to 6.4486.Meanwhile,combined solvent could dissolve coal polar and non-polar small molecules and expand flow space.Results could provide reference for solvent selection and parameter optimization of permeability-enhancement technology.

Experimental investigation on the permeability of gap-graded soil due to horizontal suffusion considering boundary effect

The boundary condition is a crucial factor affecting the permeability variation due to suffusion.An experimental investigation on the permeability of gap-graded soil due to horizontal suffusion considering the boundary effect is conducted,where the hydraulic head difference(DH)varies,and the boundary includes non-loss and soil-loss conditions.Soil samples are filled into seven soil storerooms connected in turn.After evaluation,the variation in content of fine sand(ΔR_(f))and the hydraulic conductivity of soils in each storeroom(C_(i))are analyzed.In the non-loss test,the soil sample filling area is divided into runoff,transited,and accumulated areas according to the negative or positive ΔR_(f) values.ΔR_(f) increases from negative to positive along the seepage path,and Ci decreases from runoff area to transited area and then rebounds in accumulated area.In the soil-loss test,all soil sample filling areas belong to the runoff area,where the gentle-loss,strengthened-loss,and alleviated-loss parts are further divided.ΔR_(f) decreases from the gentle-loss part to the strengthened-loss part and then rebounds in the alleviated-loss part,and C_(i) increases and then decreases along the seepage path.The relationship between ΔR_(f) and Ci is different with the boundary condition.Ci exponentially decreases with ΔR_(f) in the non-loss test and increases with ΔR_(f) generally in the soil-loss test.

Auto-parametric resonance of a continuous-beam-bridge model under two-point periodic excitation:an experimental investigation and stability analysis

The auto-parametric resonance of a continuous-beam bridge model subjected to a two-point periodic excitation is experimentally and numerically investigated in this study.An auto-parametric resonance experiment of the test model is conducted to observe and measure the auto-parametric resonance of a continuous beam under a two-point excitation on columns.The parametric vibration equation is established for the test model using the finite-element method.The auto-parametric resonance stability of the structure is analyzed by using Newmark's method and the energy-growth exponent method.The effects of the phase difference of the two-point excitation on the stability boundaries of auto-parametric resonance are studied for the test model.Compared with the experiment,the numerical instability predictions of auto-parametric resonance are consistent with the test phenomena,and the numerical stability boundaries of auto-parametric resonance agree with the experimental ones.For a continuous beam bridge,when the ratio of multipoint excitation frequency(applied to the columns)to natural frequency of the continuous girder is approximately equal to 2,the continuous beam may undergo a strong auto-parametric resonance.Combined with the present experiment and analysis,a hypothesis of Volgograd Bridge's serpentine vibration is discussed.

Experimental Investigation on the Strength and Ductility Performance of Steel-Timber-Steel Joints with Screw and Steel-Tube Fasteners

This article presents experimental results of steel-timber-steel(STS)joints loaded parallel to grain.Eight groups of specimens were designed,and tensile tests were performed.The fastener types and fastener numbers were considered to evaluate the tensile strengths and ductility performances of the STS joints.The screws with 6 mm diameter and the innovative steel-tubes with 18 mm diameter were adopted as connecting fasteners.The experimental results were discussed in terms of yielding and ultimate strengths,slip stiffness,and ductility factors.The ductility classification and failure mechanisms of each group of specimens were analyzed.It was demonstrated that the STS joint with large diameter steel-tubes showed acceptable ductility,which was close to the ductility of the STS joint with small diameter screws,thanks to the hollow structure of the steel-tube.The theoretical strengths of various failure modes for the joints with small diameter screws or large diameter steel-tubes were calculated and compared with the experimental results.The ductile performance of the STS joint was discussed by comparing the theoretical strengths of various failure modes.The effective number of the STS joint with multifasteners was also analyzed by considering the failure mechanisms in aspects of tensile strength and slip stiffness.

Experimental Investigation of a Fixed-geometry Two-dimensional Mixed-compression Supersonic Inlet with Sweep-forward High- light and Bleed Slot in an Inverted ＂X＂-type Layout

A fixed-geometry two-dimensional mixed-compression supersonic inlet with sweep-forward high-light and bleed slot in an inverted ＂X＂-form layout was tested in a wind tunnel. Results indicate： （1） with increases of the free stream Mach number, the total pressure recovery decreases, while the mass flow ratio increases to the maximum at the design point and then decreases; （2） when the angle of attack, a, is less than 6°, the total pressure recovery of both side inlets tends to decrease, but, on the lee side inlet, its values are higher than those on the windward side inlet, and the mass flow ratio on lee side inlet increases first and then falls, while on the windward side it keeps declining slowly with the sum of mass flow on both sides remaining almost constant; （3） with the attack angle, a, rising from 6° to 9°, both total pressure recovery and mass flow ratio on the lee side inlet fall quickly, but on the windward side inlet can be observed decreases in the total pressure recovery and increases in the mass flow ratio; （4） by comparing the velocity and back pressure characterristics of the inlet with a bleed slot to those of the inlet without, it stands to reason that the existence of a bleed slot has not only widened the steady working range of inlet, but also made an enormous improvement in its performance at high Mach numbers. Besides, this paper also presents an example to show how this type of inlet is designed.

Experimental Investigation on Element Immersing Process of Immersed Tube Tunnel

Bridges and tunnels are good solutions to transportation problems in large cities separated by large rivers. In bridge construction great success has been achieved in China, but large-sized immersed tube tunnel construction is still new. Element immersing is an important process of immersed tube tunnel construction. The accuracy of tunnel element positioning directly determines the quality of tunnel construction. In order to study the behavior of elements during its lowering to the sea bed, the experiments carried out in the State Key Laboratory of Ocean Engineering of Shanghai Jiaotong University. In consideration of the construction experience abroad and by reference to published papers on the Oresund tunnel in Norway-Sweden and Tokyo Bay tunnel in Japan, an element model to an appropriate scale is developed. A concise description of the model experiment wave environments is carried out, and the feasibility of two immersing strategies is studied.

Industrially Experimental Investigations and Development of the Curve-ROD Baffle Heat Exchanger

The conventional heat exchanger with segmental baffles is prone to bring forth fluid-induced vibration of heat transfer tubes and increase the pressure drop of shell-side greatly at higher fluid flow velocity. In order to avoid the above defects, the ROD-baffle heat exchanger has been developed. However, its collocation of heat transfer tubes is conventionally in square, which leads to fewer heat transfer area per unit volume. Based on the ROD-baffle heat exchanger, a new type curve-ROD baffle has been developed, and an industrial investigation of the curve-ROD baffle heat exchanger with normal triangular collocation has been carried into execution. In this paper, two equations using the Reynolds number were acquired to predict the heat transfer coefficients of the shell-side and tube-side. The experimental results show that the shell-side heat transfer and pressure drop characteristics of the curve-ROD baffle heat exchanger are superior to those of the segmental baffle one.

Theoretical and Experimental Investigation of Flexural Vibration Transfer Properties of High-Pressure Periodic Pipe

According to the theory of phononic crystals, the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps. We present theoretical and experimental investigations into the flexural vibration transfer properties of a high-pressure periodic pipe with the force on the inner pipe wall by oii pressure taken into consideration. The results show that the vibration attenuation of periodic pipe decreases along with the elevation of working pressure for the hydraulic system, and the band gaps in low frequency ranges move towards high frequency ranges. The periodic pipe has good vibration attenuation performance in the frequency range below 1000 Hz and the vibration of the hydraulic system is effectively suppressed. A11 the results are validated by experiment. The experimental results show a good agreement with the numerical calculations, thus the flexural vibration transfer properties of the high- pressure periodic pipe can be precisely calculated by taking the fluid structure interaction between the pipe and oil into consideration. This study provides an effective way for the vibration control of the hydraulic system.

Experimental Investigation on Performance of Pulse Detonation Rocket Engine Model

The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and purge gas. PDRE test model was 50 mm in inner diameter by 1.2 m long. The DDT （deflagration to detonation transition） enhancement device Shchelkin spiral was used in the test model. The effects of detonation frequency on its time-averaged thrust and specific impulse were experimentally investigated. The obtained results showes that the time-averaged thrust of PDRE test model was approximately proportional to the detonation frequency. For the detonation frequency 20 Hz, the time-averaged thrust was around 107 N, and the specific impulse was around 125 s. The nozzle experiments were conducted using PDRE test model with three traditional nozzles. The experimental results obtained demonstrated that all of those nozzles could augment the thrust and specific impulse. Among those three nozzles, the convergent nozzle had the largest increased augmentation, which was approximately 18%, under the specific condition of the experiment.

Dynamic parameters of multi-cabin protective structure subjected to low-impact load e Numerical and experimental investigations

The dynamic response of a multi-cabin protective structure subjected to impact load directly affects the protective performance of materials;thus,studying the dynamic response and communication law of wave effect of the load plays an important role in the prediction of protective performance.In this study,the protection experiments of box-structure under air-and/or water-medium are conducted,the dynamic response of the structure subjected to low-impact load is analyzed,and the corresponding numerical simulations are analyzed using the theory of finite element method(FEM).Combined with experimental and FEM simulations,the shock strain distribution,acceleration attenuation,and signal energy in defensive materials are determined.Based on the results,the metal structure exhibits good absorption characteristics for shock vibration.Using the experimental data,we also show that the attenuation of shock wave in water medium should be significantly better than that in air medium,and the protective structure should be designed for a combination of water and air mediums.Meanwhile,the numerical simulation can provide a quantitative analysis process for dynamic analysis of defensive materials.

EXPERIMENTAL INVESTIGATION AND COMPUTER SIMULATION ON DYNAMIC BUCKLING BEHAVIOR OF LIQUID-FILLED CYLINDRICAL SHELLS UNDER AXIAL IMPACT

This article reports an experimental investigation on the axial impact buckling of thin metallic cylindrical shells fully filled with water. Low velocity impact tests are carried out by DHR-9401 drop hammer rig. The whole process of dynamic buckling is simulated using LS-DYNA computer code. The consistency between experimental observation and numerical simulation is quite satisfactory. The investigation indicates that quite high internal hydrodynamic pressure occurs inside the shell during the impact process. Under the combined action of the high internal pressure and axial compression plastic buckling occurs easily in the thin-walled shells and buckling modes take on regular and axisymmetric wrinkles.

Experimental investigation on tensile strength of butt welded joint post high temperatures

In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high temperatures. The tests indicate that specimens appear ductile fracture at the steel plate during the tension tests after cooling down. The maximum temperatures undergone and the cooling pattern are major factors influencing tensile strength of butt welded joint post high temperatures. The tensile strength mostly reduces by 8% within 900℃. Based on the experimental results, the paper proposes the calculation formulas of tensile strength of butt welded joint post high temperatures. The conclusions of the paper supply references for evaluation damage and reinforcement of steel structure post fire.

Multi-type sensor placement and response reconstruction for building structures: Experimental investigations

Estimation of lateral displacement and acceleration responses is essential to assess safety and serviceability of high-rise buildings under dynamic loadings including earthquake excitations. However, the measurement information from the limited number of sensors installed in a building structure is often insufficient for the complete structural performance assessment. An integrated multi-type sensor placement and response reconstruction method has thus been proposed by the authors to tackle this problem. To validate the feasibility and effectiveness of the proposed method, an experimental investigation using a cantilever beam with multi-type sensors is performed and reported in this paper. The experimental setup is first introduced. The finite element modelling and model updating of the cantilever beam are then performed. The optimal sensor placement for the best response reconstruction is determined by the proposed method based on the updated FE model of the beam. After the sensors are installed on the physical cantilever beam, a number of experiments are carried out. The responses at key locations are reconstructed and compared with the measured ones. The reconstructed responses achieve a good match with the measured ones, manifesting the feasibility and effectiveness of the proposed method. Besides, the proposed method is also examined for the cases of different excitations and unknown excitation, and the results prove the proposed method to be robust and effective. The superiority of the optimized sensor placement scheme is finally demonstrated through comparison with two other different sensor placement schemes： the accelerometer-only scheme and non-optimal sensor placement scheme. The proposed method can be applied to high-rise buildings for seismic performance assessment.

Experimental investigation on friction stir welding of 2A12 aluminium alloys

Friction stir welding experiments were conducted to study the effects of the process parameters on the weld quality of 2A12 aluminium alloys. Through appropriate selection of the shoulder press amount （axial force）, tool rotation speed and welding speed, good joints were obtained for the test pieces with thickness of 6 ram. The microstructures in weld nugget zone, thermo-mechanical affected zone and heat-affected zone were analyzed. It is found that the ratio of the tool rotation speed to the welding speed should be optimized for a suitable shoulder press amount.

Experimental Investigation of Electronic Structure of La(O,F)BiSe_2

La（O,F）BiSe2 is a layered superconductor and has the same crystal structure with La（O,F）BiS2. We investigate the electronic structure of La（O,F）BiSe2 using the angle-resolved photoemission spectroscopy. Two electron-like Fermi surfaces around X（π, 0） are observed, corresponding to the electron doping of 0.23 per Bi site. We clearly resolve anisotropic band splitting along both Г-X and M-X due to the cooperative effects of large spin-orbit coupling and interlayer coupling. Moreover, we observe an almost non-dispersive electronic state around -0.2 eV between the electron-like bands. This state vanishes after in-situ K evaporation, indicating that it could be the localized surface state caused by defects on the cleaved surface.

Multi-objective Optimization Design and Experimental Investigation of Centrifugal Fan Performance

Current studies of fan performance optimization mainly focus on two aspects： one is to improve the blade profile, and another is only to consider the influence of single impeller structural parameter on fan performance. However, there are few studies on the comprehensive effect of the key parameters such as blade number, exit stagger angle of blade and the impeller outlet width on the fan performance. The G4-73 backward centrifugal fan widely used in power plants is selected as the research object. Based on orthogonal design and BP neural network, a model for predicting the centrifugal fan performance parameters is established, and the maximum relative errors of the total pressure and efficiency are 0.974% and 0.333%, respectively. Multi-objective optimization of total pressure and efficiency of the fan is conducted with genetic algorithm, and the optimum combination of impeller structural parameters is proposed. The optimized parameters of blade number, exit stagger angle of blade and the impeller outlet width are seperately 14, 43.9~, and 21 cm. The experiments on centrifugal fan performance and noise are conducted before and after the installation of the new impeller The experimental results show that with the new impeller, the total pressure of fan increases significantly in total range of the flow rate, and the fan efficiency is improved when the relative flow is above 75%, also the high efficiency area is broadened. Additionally, in 65% -100% relative flow, the fan noise is reduced. Under the design operating condition, total pressure and efficiency of the fan are improved by 6.91% and 0.5%, respectively. This research sheds light on the considering of comprehensive effect of impeller structrual parameters on fan performance, and a new impeller can be designed to satisfy the engineering demand such as energy-saving, noise reduction or solving air pressure insufficiency for power plants.

Seismic response control of a complex structure using multiple MR dampers: experimental investigation

This paper presents an experimental investigation on semi-active seismic response control of a multi- story building with a podium structure using multiple magnetorheological (MR) dampers manipulated by a logic control algorithm.The experiments are performed in three phases on a seismic simulator with a slender 12-story building model representing a multi-story building and a relatively stiff 3-story building model typifying a podium structure.The first phase of the investigation is to assess control performance of using three MR dampers to link the 3-story building to the 12-story building,in which seismic responses of the controlled two buildings are compared with those of the two buildings without any connection and with rigid connection.The second phase is to investigate reliability of the semi-active control system and robustness of the logic control algorithm when 2 out of 3 MR dampers fail and when the electricity supply to MR dampers is completely stopped.The last phase is to examine sensitivity of semi-active control performance of two buildings to change in ground excitation.The experimental results show that multiple MR dampers with the logic control algorithm can achieve a significant reduction in seismic responses of both buildings.The proposed semi-active control system is of high reliability and good robustness.

Experimental Investigation of Wavelength-Tunable All-Normal-Dispersion Yb-Doped Mode-Locked Fiber Lasers:Compression and Amplification

Wavelength-tunable ultrashort pulse source with high energy is highly desired for a lot of applications. The wavelength-tunable all-normal-dispersion （ANDi） mode-locked fiber laser, which can be compressed easily and amplified by an all-fiber structure, is a promising seed of such a source with compact structures. The pulse compression and amplification at different center wavelengths （from 1026 to 1058nm） of the tunable ANDi Yb- doped mode-locked fiber lasers that we previously proposed are experimentally investigated in this work. It is found that, for different wavelengths, the duration and chirp of the direct output pulse from the oscillator vary considerably, however, the duration of compressed pulse fluctuates less. For the amplification process, due to the unf/at gain spectrum of Yb-doped fiber, the gain at a short wavelength is larger than that at a long wavelength. Consequently, the trends of spectrum distortions induced by the amplification process are different for different wavelengths. These results and analyses will be helpful for the design of a high-energy and wavelength-tunable ultrashort pulse source based on an ANDi seed.

EXPERIMENTAL INVESTIGATION ON R134A AIRBORNE VAPOR-COMPRESSION REFRIGERATION SYSTEM

The airborne high power electrical equipments have been widely used in modern aircrafts , which consequently causes the dramatic increase of heating load up to dozens of kilowatts.Accordingly , vapor-compression refrigeration system ( VCRS ) with lower engine bleed air and larger refrigeration capacity has been paid much attention in recent years.Therefore , based on the analysis of the characteristics of VCRS , an experiment system of VCRS using R134ais set up to simulate operation performances.The influences of different parameters including evaporation pressure , condensing pressure , refrigerant mass flow rate and compressor rotation speed are also investigated.The impacts of different parameters on the system performance are various.This work can help to establish the specific control law under different work conditions.

Experimental Investigation into Shaping Particle-reinforced Material by WEDM-H

Al 2O 3 particle-reinforced material (6061 alloy ), which is one of new composites and characterized by high strength and small spe cific gravity, good wear resistance and corrosion resistance, has been widel y used in industry. But it is difficult to machine. Because of electric conducti vity, it can be shaped and processed by electro-machining means. However, this kind of material is mixed with the electrically conductive substances and the di electrically conductive substances, its machining process shows substantially di fferent from the machining of ordinary metal materials. This paper, based on a c ontrast experiment, investigates the machining mechanism and technique by WEDM t o shape the material and gives the optimum selection for the electric paramete rs in operation. The technologic index of shaping the new material by WEDM includes the cutting r ate and the surface roughness. There are a lot of factors that affect the techno logic index of WEDM, in which the electric parameters such as the machining volt age and current as well as the pulse duration, interval and frequency, play an i mportant part. In this experiment, the study focus mainly on the effect of the e lectric parameters on machining process and an orthogonal design is employed to select the proper electric parameters. By experiment, we find how the voltage and current affect machining process and study the removal mechanism by WEDM-HS to machine Al 2O 3 particle-reinforce d material. Besides the machining current and voltage, there are still other fac tors that can affect machining process and state. In order to find out which is the most important factor and to optimize the electric parameters, the orthogona l design has been adopted to perform the experiment. By the analysis to the rela tive differences among different factor levels, the rank of significance for fou r factors is in turn the pulse duration, the voltage, the machining current and the pulse interval. At last we can draw a conclusion that 6061 alloy can be shaped by WEDM-HS, and give the suitable electric parameters to obtain good surface roughness and high machining efficiency.