PROGRESSES MADE IN EXPERIMENTAL STUDIES OF SHALLOW-WATER ACOUSTICS

Acomprehensive experiment on shallow water acoustics with the inseparable combination of the acoustical and oceanographic means, which is uncommon internationally, was conducted successfully in the Far Yellow Sea by a group of Chinese and U.S. scientists from August 21 to September 1,1996. The basic task of ocean acoustic research is to study the interaction between sound wave and ocean media, which includes exploring the laws of influence due to spatial and temporal variability of the ocean environment, such as ocean surface waves,inhomogeneity of sea water and sea bottom struc-

Recent progresses in the development of tubular segmented-in-series solid oxide fuel cells:Experimental and numerical study

Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs suffer from having a higher volume,current leakage,complex connections,and difficulty in gas sealing.To solve these problems,Rolls-Royce has fabricated a simple design by stacking cells in series on an insulating porous support,resulting in the tubular segmented-in-series solid oxide fuel cells(SIS-SOFCs),which achieved higher output voltage.This work systematically reviews recent advances in the structures,preparation methods,perform-ances,and stability of tubular SIS-SOFCs in experimental and numerical studies.Finally,the challenges and future development of tubular SIS-SOFCs are also discussed.The findings of this work can help guide the direction and inspire innovation of future development in this field.

Experimental Analysis of Radial Centrifugal Pump Shutdown

Centrifugal pumps are widely used in the metallurgy,coal,and building sectors.In order to study the hydraulic characteristics of a closed impeller centrifugal pump during its shutdown in the so-called power frequency and frequency conversion modes,experiments were carried to determine the characteristic evolution of parameters such as speed,inlet and outlet pressure,head,flow rate and shaft power.A quasi-steady-state method was also used to further investigate these transient behaviors.The results show that,compared to the power frequency input,the performance parameter curves for the frequency conversion input are less volatile and smoother.The characteristic time is longer and the response to shutdown is slower.The quasi-steady-state theoretical head-flow curves match the experimental head-flow curves more closely at low flow rates when the frequency conversion input is considered.Moreover,in this case,the similarity law predicts the hydraulic performance more accurately.

Experimental studies of nonlinear reflection on isotropic solid interface

Nonlinear reflection of SV shear wave at the isotropic solid-solid interfaces is experimentally studied. The reflected second harmonic SV shear wave is measured for glass-air,glass-iron, copper and aluminum interfaces. The relation of nonlinear reflective coefficient with the incident angle and linear as well as nonlinear characteristics of the materials is thoroughly investigated. Comparison of the experiment with the theory gives qualitatively agreement.

Experimental studies of water hammer in propellant feed system of reaction control system

Water hammer pressure transient produces large dynamic forces which can damage the pipes and other assemblies in the feed line of a reaction control system(RCS).It has led to the failure of pressure transducers monitoring the manifold pressure in the feed line of RCS.Therefore,water hammer studies have been carried out to understand its effect in feed line.Feedline system has been simplified to develop a mathematical model and experiments have been carried out at extensive levels.The mathematical model was developed considering pipe of uniform c/s and moving liquid-gas interface.The experimental studies have been done using water as working medium instead of actual propellant.The studies showed that rate of pressurization have a very critical role on the water hammer amplitude.Sensitivity studies have been also carried out to study the effect of density,friction and initial liquid column length on water hammer amplitude.

Pharmacological and immunological effects of praziquantel against Schistosoma japonicum:a scoping review of experimental studies

Background:Chemotherapy for schistosomiasis has been around for 100 years.During the past century,great efforts have been made to develop new antischistosomal drugs from antimonials to nonantimonials,and some of these have been used extensively in clinical treatment.With the exception of a few drugs,such as oxamniquine and metrifonate,most of the antischistosomals developed in the pre-praziquantel period have variable limitations with respect to safety and efficacy.Although oxamniquine and metrifonate have been used for schistosomiasis control,they are only effective against Schistosoma mansoni and S.haematobium,respectively.Currently,praziquantel is the only drug used for treatment of all five species of human schistosomes.In this review,the pharmacological and immunological effects of praziquantel against S.japonicum are summarized and discussed.Main text:From the end of the 1970s until the 2000s,scientists have conducted a series of experimental studies on the effects of praziquantel against S.japonicum.These have included examining its unique pharmacological action on schistosomes,the characteristics in susceptibility of the different developmental stages of schistosomes to the drug,the relationship between plasma concentration of the drug and efficacy,the impact of host factors on cidal action of the drug,prevention and early treatment of schistosomal infection,as well as praziquantel-resistant schistosomiasis.Conclusion:The effects of praziquantel against S.japonicum,as elucidated by the experimental studies that are reviewed in this paper,may have some reference significance for the development of new antischistosomals.

The scaling laws of cabin structures subjected to internal blast loading:Experimental and numerical studies

This paper presents a combination of experimental and numerical investigations on the dynamic response of scaling cabin structures under internal blast loading.The purpose of this study is to modify the similar relationship between the scaled-down model and the prototype of the cabin structures under internal blast loading.According to the Hopkinson’s scaling law,three sets of cabin structure models with different scaling factors combined with different explosive masses were designed for the experimental study.The dynamic deformation process of the models was recorded by a three-dimensional digital imaging correlation(DIC)method and a 3D scanning technology was used to reconstruct the deformation modes of the specimen.In addition,a finite element model was developed for the modification of the scaling law.The experimental results showed that the final deflection-to-thickness ratio was increased with the increase of the model size despite of the similar trend of their deformation processes.The reason for this inconsistency was discussed based on the traditional scaling law and a modified formula considering of the effects of size and strain-rate was provided.

Experimental study of the temporary plugging capability of diverters to block hydraulic fractures in high-temperature geothermal reservoirs

The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.

Experimental investigation on pressure-buildup characteristics of a water lump immerged in a molten lead pool

Motivated to understand the pressure-buildup characteristics in a circumstance of a water droplet immerged inside a heavy liquid metal pool,which is a key phenomenon during a Steam Generator Tube Rupture accident of Lead-cooled Fast Reactor,many experiments have been conducted by injecting water lumps into a molten lead pool at Sun Yat-sen University.In order to deepen the understanding of the influence of melt material,this lead experiment was compared with a Lead-Bismuth-Eutectic(LBE)experiment in the literature.For both experiments,a steam explosion occurred in a small part of the experi-mental runs,which generally leads to strengthened pressure buildup.Regarding the non-explosion experimental cases,the impact of all parameters employed in lead experiments(i.e.,water lump volume,water lump shape,molten pool depth,and temperature of water and melt)on the pressure buildup is non-negligible and similar to that in our previous experiments using LBE.Notably,limited pressure buildup with an increase in water lump volume was also observed.A slightly more violent pressure buildup tends to appear in the lead experiments than in the LBE experiments under the same experimental conditions,which may be due to the higher thermal conductivity of lead than of LBE.In a few experimental runs with a relatively low melt temperature close to the melting point of lead,local solidification of liquid lead was observed,restricting pressure buildup.For the lead and LBE experiments,the calculated melt kinetic energy conversion efficiencyηhas a relatively small value(not exceeding 1.6%),and theηvalues have an overall positive correlation with the impulse on the molten pool.

Experimental study on the mechanism of flow blockage formation in fast reactor

Various sources of solid particles might exist in the coolant flow of a liquid metal cooled fast reactor(e.g.,through chemical interaction between the coolant and impurities,air,or water,through corrosion of structural materials,or from damaged/molten fuel).Such particles may cause flow blockage accidents in a fuel assembly,resulting in a reduction in coolant flow,which potentially causes a local temperature rise in the fuel cladding,cladding failure,and fuel melt.To understand the blockage formation mechanism,in this study,a series of simulated experiments was conducted by releasing different solid particles from a release device into a reducer pipe using gravity.Through detailed analyses,the influence of various experimental parameters(e.g.,particle diameter,capacity,shape,and static friction coefficient,and the diameter and height of the particle release nozzle)on the blockage characteristics(i.e.,blockage probability and position)was examined.Under the current range of experimental conditions,the blockage was significantly influenced by the aforementioned parameters.The ratio between the particle diameter and outlet size of the reducer pipe might be one of the determining factors governing the occurrence of blockage.Specifically,increasing the ratio enhanced blockage(i.e.,larger probability and higher position within the reducer pipe).Increasing the particle size,particle capacity,particle static friction coefficient,and particle release nozzle diameter led to a rise in the blockage probability;however,increasing the particle release nozzle height had a downward influence on the blockage probability.Finally,blockage was more likely to occur in non-spherical particles case than that of spherical particles.This study provides a large experimental database to promote an understanding of the flow blockage mechanism and improve the validation process of fast reactor safety analysis codes.

Experimental Study on the Treatment of Tertiary Oil Recovery Wastewater via a Novel Electro-Coagulation Method

At present,methods for treating tertiary oil recovery wastewater via electro-coagulation are still in their early stage of development.In this study,a device for electro-coagulation wastewater treatment was built and tested in an oil field.The effects that the initial pH value,electrode type,and connection mode have on the coagulation and separation effect were assessed by measuring the mass fraction and turbidity of oil.The results have shown that when the electro-coagulation method is used,the effectiveness of the treatment can be significantly increased in neutral pH conditions(pH=7),in acidic conditions,and in alkaline conditions.Compared to an Al electrode,the floc that is produced by an Fe electrode is smaller;thus,it does not easily coagulate and settle in a short time.Using the oil removal rate,turbidity removal rate and energy consumption as a basis to assess the performances,the results have demonstrated that the combined aluminum alloy iron composite electrode should be used as electrolytic electrode.

Analysis and Experimental Study on the Friction Force at the Binding Point of Flexible Cable on Satellite

Mainly for the problem that the friction force generated by the existing process of bind-ing,fixing and fastening the flexible cable on the satellite is unknown,the friction force analysis and experimental research on the binding point of the flexible cable are carried out.The equivalent model of the cable bundle bound by nylon cable ties is established,the force on the binding point is analyzed,and the empirical formula for calculating the friction force at the binding point is estab-lished.The formula shows that the friction force is related to the cable bundle diameter,the number of winding cycles of silicone rubber tape,the width of nylon cable ties,and the binding force.The friction force tests of the cable diameter of 5.06 mm,8.02 mm,24.02 mm,38.04 mm under different winding turns of tape were carried out,which was compared with the theoretical calculation value.It is concluded that the calculation accuracy of the theoretical model is more than 95%,which can estimate the actual friction force value accurately.This provides a reference and basis for the theoretical and experimental research on the friction force of the flexible cable binding point on satellite.

Experimental study on strain field evolution around a simulated thrust fault

Earthquakes result from continuous geodynamic processes.A topic of significant interest for the scientific community is to elaborate on the phenomena governing the faulting and fracturing of crustal rocks.Therefore,in this study,uniaxial compressive shear failure experiments were conducted on Fangshan marble rock samples with a prefabricated slot to simulate thrust faulting.The center of each marble plate(105 mm × 80 mm × 5 mm) was engraved with a 30-mm long double-sided nonpenetrating slot(depth:2 mm,width:0.5 mm).The deformation and destruction processes of the rock surface were recorded using a high-speed camera.The digital image correlation method was used to calculate the displacement and strain distribution and variation at different loading stages.The accumulative and incremental displacement fields u and v,strain field exand e_(y),and shear strain e_(xy) were analyzed.When the loading level reached its ultimate value,the strain field was concentrated around the prefabricated slot.The concentration reached a maximum at the ends of the prefabricated slot.The magnitude of shear strain reached 0.1.This experiment contributes to our understanding of the dynamic process of active faulting.

Knowledge and Perceptions of Hospital Care Staff towards Medical Internet of Things and the Role of Awareness Videos: A Quasi Experimental Study

Introduction: The healthcare industry continues to adopt and integrate smart technology into its operations. However, the adoption of the eHealth solutions has not been smooth in the Kingdom of Saudi Arabia (KSA) due to negative beliefs about the technology, lack of awareness and motivation and resistance to change. Thus, this study was developed to investigate the knowledge and perceptions of hospital care staff towards the Medical Internet of Things and to explore the role of awareness videos in changing negative perceptions. Methods: One group pre-test post-test quasi-experimental study design was incorporated, and 116 participants from Ministry of Health hospitals in Riyadh, KSA, were included. A series of four videos were developed to observe their influence on the knowledge and perceptions of mIoT. Results: The findings showed that participants had more knowledge about the individual components of mIoT (particularly wearable devices) compared to the processes or functions of mIoT. Similarly, just over half (56.0%) of the individuals think that the current systems in the hospital are enough to deliver mIoT. However, 90% think mIoT is the future of digital health. Similarly, PE, SI, BI, EE and CESE were considered facilitators and PTA and CC were considered grave barriers to mIoT adoption. The awareness videos positively influenced knowledge and perceptions of PE, EE, CESE and SI. Conclusion: The study concludes that hospital staff in Riyadh (excluding doctors) possess basic mIoT knowledge, consider various adoption factors as enablers, and awareness video can play a critical role in effectively introducing the technology to the hospital care staff.

Experimental Study of Primary School Students’Independent Reading Based on the Network Teaching Platform

The development of information technology, especially the rise of online teaching platforms, has changed the way people read and the methods they use. Under this influence, primary school students’ independent reading has also been changed. However, due to limited self-control and understanding, primary school students face certain difficulties when using online teaching platforms for independent reading. Advantages and disadvantages of distance learning based on the network teaching platform were summarized in this paper. A one-year experiment study was carried out on our school fifth-grade students in independent reading using WeChat campus platform considering their current situation and existing problems of independent reading. In experiment study an independent reading mode was introduced. The results show that this reading mode can significantly improve students’ independent reading ability.

船舶进气畸变模拟板结构设计与参数分析

Significant aerodynamic engine instability can occur during the operation of marine gas turbines as airflow enters the compressor through a 90°turning and causes inlet distortion.This study adopts the method of simulating board equivalence to provide the target distortion flow field for ship compressors.The characteristics of the flow field behind the simulated board are obtained through experiments and numerical simulations,through which the relationship between the height of the simulated board and the total pressure distortion is elucidated.Subsequently,the study summarizes the prediction formula to achieve a distortion prediction of 0.8%–7.8%.In addition,this work analyzes the effects of drilling methods and diameters on flow nonuniformity by drilling holes into the simulation board.The results indicate that drilling holes on the board can weaken the nonuniformity of the flow field within a certain range and change the distribution pattern of total pressure in the cross-section.Furthermore,the total pressure distortion no longer changes significantly when the number of holes is too large.The proposed double simulation board structure is capable of obtaining the following two types of distorted flow fields:symmetrical dual lowpressure zones and low-pressure zones with high distortion intensity at the compressor inlet.The distortion equivalent simulation method proposed in this work can obtain various types of distortion spectra,thereby meeting the distortion parameter requirements for the antidistortion testing of marine engines.

Parametric study on contact sensors for MASW measurement-based interfacial debonding detection for SCCS

Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding status plays an essential role in guaranteeing the structural performance of SCCS.Accordingly,efficient non-destructive testing(NDT)on interfacial debondings in SCCS has become a prominent research area.Multi-channel analysis of surface waves(MASW)has been validated as an effective NDT technique for interfacial debonding detection for SCCS.However,the feasibility of MASW must be validated using experimental measurements.This study establishes a high-frequency data synchronous acquisition system with 32 channels to perform comparative verification experiments in depth.First,the current sensing approaches for high-frequency vibration and stress waves are summarized.Secondly,three types of contact sensors,namely,piezoelectric lead-zirconate-titanate(PZT)patches,accelerometers,and ultrasonic transducers,are selected for MASW measurement.Then,the selection and optimization of the force hammer head are performed.Comparative experiments are carried out for the optimal selection of ultrasonic transducers,PZT patches,and accelerometers for MASW measurement.In addition,the influence of different pasting methods on the output signal of the sensor array is discussed.Experimental results indicate that optimized PZT patches,acceleration sensors,and ultrasonic transducers can provide efficient data acquisition for MASW-based non-destructive experiments.The research findings in this study lay a solid foundation for analyzing the recognition accuracy of contact MASW measurement using different sensor arrays.

Experimental Research on the Dynamic Lubricating Performance of Slipper/Swash Plate Interface in Axial Piston Pumps

The interface between the slipper/swash plate is one of the most important frication pairs in axial piston pumps.The test of this interface in a real pump is very challenging.In this paper,a novel pump prototype is designed and a test rig is set up to study the dynamic lubricating performance of the slipper/swash-plate interface in axial piston machines.Such an experimental setup can simulate the operating condition of a real axial piston pump without changing the relative motion relationship of the interfaces.Considering the lubricant oil film thickness as the main measurement parameter,the attitude of the slipper under the conditions of different load pressure,rotation speed and charge pressure are studied experimentally.After the test,the wear state of the swash plate is observed.According to the friction trace on the surface of the swash plate,the prediction for the attitude of the slipper and the zone easy to wear are verified.

Experimental Study on Deoxidization of Bariumand Barium Alloy

Based on the review of latest papers related to the application of barium alloy, the deoxidizationeffects of barium and barium alloy, and the dynamic characteristics of molten bath have beensystematically studied by means of the convection free bath, natural convection bath, air andvacuum induction melting experiments. It was found that both the total oxygen content andsoluble oxygen content in molten bath decreased rapidly. The results obtained provided practicaland theoretical basis for further synthetic applications of barium alloy in metallurgical industry.