Recent progresses in the development of tubular segmented-in-series solid oxide fuel cells:Experimental and numerical study

Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs suffer from having a higher volume,current leakage,complex connections,and difficulty in gas sealing.To solve these problems,Rolls-Royce has fabricated a simple design by stacking cells in series on an insulating porous support,resulting in the tubular segmented-in-series solid oxide fuel cells(SIS-SOFCs),which achieved higher output voltage.This work systematically reviews recent advances in the structures,preparation methods,perform-ances,and stability of tubular SIS-SOFCs in experimental and numerical studies.Finally,the challenges and future development of tubular SIS-SOFCs are also discussed.The findings of this work can help guide the direction and inspire innovation of future development in this field.

The growth ofβphase in Mg-Gd-Y-Ni alloy by experimental and first-principles study

The paper reports on the atomic investigation aboutβphase in Mg_(96)Gd_(2)Y_(1)Ni_(1) alloy by using the first-principles study and the high-angle annular dark-field scanning transmission electron microscope(HAADF-STEM)corrected by atomic Cs.By using HAADF-STEM,the rectangularβphases were observed in the underage and peak aging stages in Mg_(96)Gd_(2)Y_(1)Ni_(1) alloy.Theβphase could be precipitated from the previously precipitatedβphase,and theβphase grew in steps when it was precipitated.A special transition structure of three atomic layer thicknesses was first observed at the edge of theβphase and the structure of this interface is probably as theβ/Mg_(1) interface for the analysis of thermodynamic characterization and electronic characterization.Theβ'phase and theβ_(H) structure were precipitated only at the edge of the length directions of theβphase.Theβ'phase continues to grow into aβphase directly without the formation ofβ_(1) phase,resulting in an increase in the length of theβphase,which is discovered for the first time.

Analysis of the Erosion-Corrosion Mechanism of the Air Cooler in a Hydrocracking Unit:A Numerical and Experimental Study

Corrosion leakages often occur in the air cooler of a hydrocracking unit,with the failure sites mainly located in the entrance area of the tubes.An analysis of the macroscopic morphology and corrosion products confirmed that the damage was caused by erosion-corrosion(E-C).Numerical and experimental methods were applied to investigate the E-C mechanism in the air cooler.Computational fluid dynamics(CFD)was used to calculate the hydrodynamic parameters of the air cooler.The results showed that there was a biased flow in the air cooler,which led to a significant increase in velocity,turbulent kinetic energy and wall shear within 0.2 m of the tube entrance.A visualization experiment was then performed to determine the principles of migration and transformation of multiphase flow in the air cooler tubes.Various flow patterns(pure droplet flow,mist flow,and annular flow)and their evolutionary processes were clearly depicted experimentally.The initiation mechanism and processes leading to the development of E-C in the air cooler were also determined.This study provided a comprehensive explanation for the E-C failures that occur in air coolers during operation.

Efficacy of Juanbi capsule on ameliorating knee osteoarthritis:a network pharmacology and experimental verification-based study

Background:The purpose of the study was to investigate the active ingredients and potential biochemical mechanisms of Juanbi capsule in knee osteoarthritis based on network pharmacology,molecular docking and animal experiments.Methods:Chemical components for each drug in the Juanbi capsule were obtained from Traditional Chinese Medicine Systems Pharmacology Database and Analysis Platform,while the target proteins for knee osteoarthritis were retrieved from the Drugbank,GeneCards,and OMIM databases.The study compared information on knee osteoarthritis and the targets of drugs to identify common elements.The data was imported into the STRING platform to generate a protein-protein interaction network diagram.Subsequently,a“component-target”network diagram was created using the screened drug components and target information with Cytoscape software.Common targets were imported into Metascape for GO function and KEGG pathway enrichment analysis.AutoDockTools was utilized to predict the molecular docking of the primary chemical components and core targets.Ultimately,the key targets were validated through animal experiments.Results:Juanbi capsule ameliorated Knee osteoarthritis mainly by affecting tumor necrosis factor,interleukin1β,MMP9,PTGS2,VEGFA,TP53,and other cytokines through quercetin,kaempferol,andβ-sitosterol.The drug also influenced the AGE-RAGE,interleukin-17,tumor necrosis factor,Relaxin,and NF-κB signaling pathways.The network pharmacology analysis results were further validated in animal experiments.The results indicated that Juanbi capsule could decrease the levels of tumor necrosis factor-αand interleukin-1βin the serum and synovial fluid of knee osteoarthritis rats and also down-regulate the expression levels of MMP9 and PTGS2 proteins in the articular cartilage.Conclusion:Juanbi capsule may improve the knee bone microstructure and reduce the expression of inflammatory factors of knee osteoarthritis via multiple targets and multiple signaling pathways.

Experimental Abrasion Study of the Evolution of Gold Morphological Criteria in Different Sediments as a Function of Time

The use of gold as a tracer element for understanding the mode of emplacement of these formations requires a good knowledge of its dynamics. To this end, we have carried out experimental studies to investigate the evolution of contour states (regular, irregular), surface states (blunt, rough), shape (elongation) and dimension (size). The study of these criteria is carried out on SEM photos of particles, taken before and after the experiment, using Aphelion image processing software. Five experiments were carried out to study the influence of sediment granulometry and water dilution on particle morphological changes. The results of these experiments show that coarse sediments (>1 mm) are largely responsible for morphological changes in gold. They cause fragmentation and/or folding of the particle edges, depending on the magnitude of the impact forces. Strong impacts due to high water dilution cause staking on the particle surface. Fine sediments (<1 mm) slow down particle evolution as they cushion impacts and particles tend to flatten rather than fragment.

Experimental study on reactions between alkaline basaltic melt and orthopyroxenes: constraints on the evolution of lithospheric mantle in the North China Craton

The experimental results of the reactions between an alkaline basaltic melt and mantle orthopyroxenes under high-temperature and high-pressure conditions of 1300–1400℃ and 2.0–3.0 GPa using a six-anvil apparatus are reported in this paper.The reactions are proposed to simulate the interactions between melts from the asthenospheric mantle and the lithospheric mantle.The starting melt in the experiments was made from the alkaline basalt occurring in Fuxin,Liaoning Province,and the orthopyroxenes were separated from the mantle xenoliths in Damaping,Hebei Province.The results show that clinopyroxenes were formed in all the reactions between the alkaline basaltic melt and orthopyroxenes under the studied P–T conditions.The formation of clinopyroxene in the reaction zone is mainly controlled by dissolution–crystallization,and the chemical compositions of the reacted melt are primarily infl uenced by the diff usion eff ect.Temperature is the most important parameter controlling the reactions between the melt and orthopyroxenes,which has a direct impact on the melting of orthopyroxenes and the diff usion of chemical components in the melt.Temperature also directly controls the chemical compositions of the newly formed clinopyroxenes in the reaction zone and the reacted melt.The formation of clinopyroxenes from the reactions between the alkaline basaltic melt and orthopyroxenes can result in an increase of CaO and Al_(2)O_(3) contents in the rocks containing this mineral.Therefore,the reactions between the alkaline basaltic melt from the asthenospheric mantle and orthopyroxenes from the lithospheric mantle can lead to the evolution of lithospheric mantle in the North China Craton from refractory to fertile with relatively high CaO and Al 2 O 3 contents.In addition,the reacted melts in some runs were transformed from the starting alkaline basaltic into tholeiitic after reactions,indicating that tholeiitic magma could be generated from alkaline basaltic one via reactions between the latter and orthopyroxene.

Experimental study of the temporary plugging capability of diverters to block hydraulic fractures in high-temperature geothermal reservoirs

The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.

Experimental study on the mechanism of flow blockage formation in fast reactor

Various sources of solid particles might exist in the coolant flow of a liquid metal cooled fast reactor(e.g.,through chemical interaction between the coolant and impurities,air,or water,through corrosion of structural materials,or from damaged/molten fuel).Such particles may cause flow blockage accidents in a fuel assembly,resulting in a reduction in coolant flow,which potentially causes a local temperature rise in the fuel cladding,cladding failure,and fuel melt.To understand the blockage formation mechanism,in this study,a series of simulated experiments was conducted by releasing different solid particles from a release device into a reducer pipe using gravity.Through detailed analyses,the influence of various experimental parameters(e.g.,particle diameter,capacity,shape,and static friction coefficient,and the diameter and height of the particle release nozzle)on the blockage characteristics(i.e.,blockage probability and position)was examined.Under the current range of experimental conditions,the blockage was significantly influenced by the aforementioned parameters.The ratio between the particle diameter and outlet size of the reducer pipe might be one of the determining factors governing the occurrence of blockage.Specifically,increasing the ratio enhanced blockage(i.e.,larger probability and higher position within the reducer pipe).Increasing the particle size,particle capacity,particle static friction coefficient,and particle release nozzle diameter led to a rise in the blockage probability;however,increasing the particle release nozzle height had a downward influence on the blockage probability.Finally,blockage was more likely to occur in non-spherical particles case than that of spherical particles.This study provides a large experimental database to promote an understanding of the flow blockage mechanism and improve the validation process of fast reactor safety analysis codes.

Experimental Study on the Treatment of Tertiary Oil Recovery Wastewater via a Novel Electro-Coagulation Method

At present,methods for treating tertiary oil recovery wastewater via electro-coagulation are still in their early stage of development.In this study,a device for electro-coagulation wastewater treatment was built and tested in an oil field.The effects that the initial pH value,electrode type,and connection mode have on the coagulation and separation effect were assessed by measuring the mass fraction and turbidity of oil.The results have shown that when the electro-coagulation method is used,the effectiveness of the treatment can be significantly increased in neutral pH conditions(pH=7),in acidic conditions,and in alkaline conditions.Compared to an Al electrode,the floc that is produced by an Fe electrode is smaller;thus,it does not easily coagulate and settle in a short time.Using the oil removal rate,turbidity removal rate and energy consumption as a basis to assess the performances,the results have demonstrated that the combined aluminum alloy iron composite electrode should be used as electrolytic electrode.

Analysis and Experimental Study on the Friction Force at the Binding Point of Flexible Cable on Satellite

Mainly for the problem that the friction force generated by the existing process of bind-ing,fixing and fastening the flexible cable on the satellite is unknown,the friction force analysis and experimental research on the binding point of the flexible cable are carried out.The equivalent model of the cable bundle bound by nylon cable ties is established,the force on the binding point is analyzed,and the empirical formula for calculating the friction force at the binding point is estab-lished.The formula shows that the friction force is related to the cable bundle diameter,the number of winding cycles of silicone rubber tape,the width of nylon cable ties,and the binding force.The friction force tests of the cable diameter of 5.06 mm,8.02 mm,24.02 mm,38.04 mm under different winding turns of tape were carried out,which was compared with the theoretical calculation value.It is concluded that the calculation accuracy of the theoretical model is more than 95%,which can estimate the actual friction force value accurately.This provides a reference and basis for the theoretical and experimental research on the friction force of the flexible cable binding point on satellite.

Experimental study on strain field evolution around a simulated thrust fault

Earthquakes result from continuous geodynamic processes.A topic of significant interest for the scientific community is to elaborate on the phenomena governing the faulting and fracturing of crustal rocks.Therefore,in this study,uniaxial compressive shear failure experiments were conducted on Fangshan marble rock samples with a prefabricated slot to simulate thrust faulting.The center of each marble plate(105 mm × 80 mm × 5 mm) was engraved with a 30-mm long double-sided nonpenetrating slot(depth:2 mm,width:0.5 mm).The deformation and destruction processes of the rock surface were recorded using a high-speed camera.The digital image correlation method was used to calculate the displacement and strain distribution and variation at different loading stages.The accumulative and incremental displacement fields u and v,strain field exand e_(y),and shear strain e_(xy) were analyzed.When the loading level reached its ultimate value,the strain field was concentrated around the prefabricated slot.The concentration reached a maximum at the ends of the prefabricated slot.The magnitude of shear strain reached 0.1.This experiment contributes to our understanding of the dynamic process of active faulting.

Parametric study on contact sensors for MASW measurement-based interfacial debonding detection for SCCS

Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding status plays an essential role in guaranteeing the structural performance of SCCS.Accordingly,efficient non-destructive testing(NDT)on interfacial debondings in SCCS has become a prominent research area.Multi-channel analysis of surface waves(MASW)has been validated as an effective NDT technique for interfacial debonding detection for SCCS.However,the feasibility of MASW must be validated using experimental measurements.This study establishes a high-frequency data synchronous acquisition system with 32 channels to perform comparative verification experiments in depth.First,the current sensing approaches for high-frequency vibration and stress waves are summarized.Secondly,three types of contact sensors,namely,piezoelectric lead-zirconate-titanate(PZT)patches,accelerometers,and ultrasonic transducers,are selected for MASW measurement.Then,the selection and optimization of the force hammer head are performed.Comparative experiments are carried out for the optimal selection of ultrasonic transducers,PZT patches,and accelerometers for MASW measurement.In addition,the influence of different pasting methods on the output signal of the sensor array is discussed.Experimental results indicate that optimized PZT patches,acceleration sensors,and ultrasonic transducers can provide efficient data acquisition for MASW-based non-destructive experiments.The research findings in this study lay a solid foundation for analyzing the recognition accuracy of contact MASW measurement using different sensor arrays.

Knowledge and Perceptions of Hospital Care Staff towards Medical Internet of Things and the Role of Awareness Videos: A Quasi Experimental Study

Introduction: The healthcare industry continues to adopt and integrate smart technology into its operations. However, the adoption of the eHealth solutions has not been smooth in the Kingdom of Saudi Arabia (KSA) due to negative beliefs about the technology, lack of awareness and motivation and resistance to change. Thus, this study was developed to investigate the knowledge and perceptions of hospital care staff towards the Medical Internet of Things and to explore the role of awareness videos in changing negative perceptions. Methods: One group pre-test post-test quasi-experimental study design was incorporated, and 116 participants from Ministry of Health hospitals in Riyadh, KSA, were included. A series of four videos were developed to observe their influence on the knowledge and perceptions of mIoT. Results: The findings showed that participants had more knowledge about the individual components of mIoT (particularly wearable devices) compared to the processes or functions of mIoT. Similarly, just over half (56.0%) of the individuals think that the current systems in the hospital are enough to deliver mIoT. However, 90% think mIoT is the future of digital health. Similarly, PE, SI, BI, EE and CESE were considered facilitators and PTA and CC were considered grave barriers to mIoT adoption. The awareness videos positively influenced knowledge and perceptions of PE, EE, CESE and SI. Conclusion: The study concludes that hospital staff in Riyadh (excluding doctors) possess basic mIoT knowledge, consider various adoption factors as enablers, and awareness video can play a critical role in effectively introducing the technology to the hospital care staff.

Experimental Analysis of Radial Centrifugal Pump Shutdown

Centrifugal pumps are widely used in the metallurgy,coal,and building sectors.In order to study the hydraulic characteristics of a closed impeller centrifugal pump during its shutdown in the so-called power frequency and frequency conversion modes,experiments were carried to determine the characteristic evolution of parameters such as speed,inlet and outlet pressure,head,flow rate and shaft power.A quasi-steady-state method was also used to further investigate these transient behaviors.The results show that,compared to the power frequency input,the performance parameter curves for the frequency conversion input are less volatile and smoother.The characteristic time is longer and the response to shutdown is slower.The quasi-steady-state theoretical head-flow curves match the experimental head-flow curves more closely at low flow rates when the frequency conversion input is considered.Moreover,in this case,the similarity law predicts the hydraulic performance more accurately.

Experimental Study of Primary School Students’Independent Reading Based on the Network Teaching Platform

The development of information technology, especially the rise of online teaching platforms, has changed the way people read and the methods they use. Under this influence, primary school students’ independent reading has also been changed. However, due to limited self-control and understanding, primary school students face certain difficulties when using online teaching platforms for independent reading. Advantages and disadvantages of distance learning based on the network teaching platform were summarized in this paper. A one-year experiment study was carried out on our school fifth-grade students in independent reading using WeChat campus platform considering their current situation and existing problems of independent reading. In experiment study an independent reading mode was introduced. The results show that this reading mode can significantly improve students’ independent reading ability.

Packed Bed Thermocline Thermal Energy Storage for Medium-Temperature Concentrating Solar Systems: Numerical and Experimental Study

Thermal Energy Storage is becoming a necessary component of sustainable energy production systems as it helps alleviate intrinsic limitations of Renewable Energy Sources, such as intermittent use and mismatch between power demand and supply. This paper discusses a packed bed thermocline tank as a thermal energy storage solution. Firstly, this paper presents the development of a numerical model calculating heat transfers within the tank, based on a discretization over several nodes and the nodal formulation of the heat balance equation. The model considers a filler material and a heat transferring fluid and uses the finite difference method to calculate the temperature evolution of the two media across the tank. The model was validated with two different packed bed systems from the literature during a discharging process, presenting a good fit with the experimental results. Secondly, the experimental packed bed is presented and characterized for a charging cycle from ambient temperature to approximately 180?C. The charging experiment was accurately reproduced with the numerical model requiring minimal computational time. Two additional charging modes were simulated with different inlet HTF conditions: constant temperature and varying temperature following the profile produced by a thermal solar collector field. The temperature profiles obtained from the three charging modes were analysed and compared to each other. The proposed numerical and experimental tools will be used in future studies for a better understanding of the design and operating conditions of packed bed thermal energy storage systems.

Experimental Study of a Modified Icaro Solar Dryer: The Case of Coffee Drying

Food losses in the developing country are thought to be 50% of the fruits and vegetables grown and 25% of harvested food grain. Food preservation can reduce wastage of a harvest surplus, allow storage for food shortages, and in some cases facilitate export to high-value markets. Drying is one of the oldest methods of food preservation. Drying makes produce lighter, smaller, and less likely to spoil and helps to minimize the moisture content in coffee beans as high moisture content during storage is certain to ruin the taste and appearance of coffee. This work presents the results of an experimental study of forced convection drying of coffee cherries in a modified Icaro solar dryer. The study aims to validate the numerical models developed for further research. The experimental tests envisaged also aim to determine the mass loss curves of the product by fixing or calculating its initial mass (1 kg), its initial water content (70%), the ambient temperature, the drying airflow (0.02 m3.s-1 to 0.09 m3.s-1) and the exchange coefficients. The influence of these aerothermal parameters on the drying time of a most commercialized coffee variety (Robusta) was studied. Finally, the results revealed an increase in the efficiency of the heat transfer air and a reduction in the water content of the coffee cherry from 70% to 9.87%, after 30.2 hours.

Experimental Study on Effect of Inclination Angle on Bubble Collapse near Attached Air Bubble

Experiments were conducted to investigate the dynamics of an oscillating bubble generated by a spark in the presence of an inclined attached air bubble.The study primarily focused on the influence of the inclination angle on the behavior of bubble jetting orientation,air bubble shape modes,and motion characteristics of the interaction between the two bubbles.Various complex bubble jetting behaviors were observed,including the presence of multiple types of bubble jetting directions,bubble splitting,and multidirectional jets.Four types of air bubble shapes were defined,namely inclined cup cover-shaped(with and without splitting),double-peaked cup cover-shaped,and inclined L-shaped air bubbles.The formation of different types of bubble jets was analyzed using the vector synthesis principle of the Bjerknes force exerted by the inclined attached air bubble and a steel plate.To describe the diverse orientations of bubble jetting and air bubble shapes,new parameters namely the dimensionless spark bubble oscillation time T^(*)and volume ratio V^(*)that consider the inclination angle are proposed.The findings of this investigation contribute to the existing knowledge and have the potential to further enhance methods for mitigating cavitation damage in marine,hydraulic machinery systems,and medical fields.l fields.

Causal associations between gastroesophageal reflux disease and essential hypertension: A bidirectional Mendelian randomization study

BACKGROUND Clinical studies have reported that patients with gastroesophageal reflux disease(GERD)have a higher prevalence of hypertension.AIM To performed a bidirectional Mendelian randomization(MR)analysis to investi-gate the causal link between GERD and essential hypertension.METHODS Eligible single nucleotide polymorphisms(SNPs)were selected,and weighted median,inverse variance weighted(IVW)as well as MR egger(MR-Egger)re-gression were used to examine the potential causal association between GERD and hypertension.The MR-Pleiotropy RESidual Sum and Outlier analysis was used to detect and attempt to reduce horizontal pleiotropy by removing outliers SNPs.The MR-Egger intercept test,Cochran’s Q test and“leave-one-out”sen-sitivity analysis were performed to evaluate the horizontal pleiotropy,heterogen-eities,and stability of single instrumental variable.RESULTS IVW analysis exhibited an increased risk of hypertension(OR=1.46,95%CI:1.33-1.59,P=2.14E-16)in GERD patients.And the same result was obtained in replication practice(OR=1.002,95%CI:1.0008-1.003,P=0.000498).Meanwhile,the IVW analysis showed an increased risk of systolic blood pressure(β=0.78,95%CI:0.11-1.44,P=0.021)and hypertensive heart disease(OR=1.68,95%CI:1.36-2.08,P=0.0000016)in GERD patients.Moreover,we found an decreased risk of Barrett's esophagus(OR=0.91,95%CI:0.83-0.99,P=0.043)in essential hypertension patients.CONCLUSION We found that GERD would increase the risk of essential hypertension,which provided a novel prevent and therapeutic perspectives of essential hypertension.

Factorial Experimental Design to Study the Effects of Layers and Fiber Content on Concrete Flexural Behavior

Experimentation has come a long in helping researchers achieve breakthroughs in their different scientific areas and engineering happens to be one of those areas with the most impact from experimental advancement. The need for valid experimental results free from biases and confounding conclusions has prompted the development of new experimental techniques that takes consideration of all applicable factor and combinations in providing answers on a research topic, and the Factorial Experimental design credited to Sir Ronald Fisher is one technique yielding highly valid results. This paper uses the factorial design of experiments to research the flexural impact of polyvinyl acetate fiber and layered concrete in construction. The experiment considered two levels of fiber contents and two levels of layers, and prepared samples with all combinations of the variable factors. The samples were tested after 7 days from casting for flexural strength and an advance statistical analysis was performed on the flexural responses of the samples using R-program. The results from the analyses revealed the significance of the variables to the flexural strength of the samples, as well as their interactions. The experiment concluded that based on the number of layers and fiber content used for the experiment, casting concrete in layers does have a significant negative effect on the flexural strength of concrete, and the failure pattern of concrete members under flexural load in evidently influenced by the material composition of the concrete, and that it can be evidently influenced by casting the concrete in layers.