Numerical Simulation of External-Cavity Distributed Feedback Semiconductor Laser

We propose a theoretical model to describe external-cavity distributed feedback semiconductor lasers and investigate the impact of the number of external feedback points on linewidth and side-mode suppression ratio through numerical simulation. The simulation results demonstrate that the linewidth of external-cavity semiconductor lasers can be reduced by increasing the external cavity length and feedback ratio, and adding more external feedback points can further narrow the linewidth and enhance the side mode suppression ratio. This research provides insight into the external cavity distributed feedback mechanism and can guide the design of high-performance external cavity semiconductor lasers. .

External-cavity birefringence feedback effects of microchip Nd:YAG laser and its application in angle measurement

External-cavity birefringence feedback effects of the microchip Nd：YAG laser are presented. When a birefringence element is placed in the external feedback cavity of the laser, two orthogonally polarized laser beams with a phase difference are output. The phase difference is twice as large as the phase retardation in the external cavity along the two orthogonal directions. The variable extra-cavity birefringence, caused by rotation of the external-cavity birefringenee element, results in tunable phase difference between the two orthogonally polarized beams. This means that the roll angle information has been translated to phase difference of two output laser beams. A theoretical analysis based on the Fabry-Perot cavity equivalent model and refractive index ellipsoid is presented, which is in good agreement with the experimental results. This phenomenon has potential applications for roll angle measurement.

Continuous-wave operation of InAs/InP quantum dot tunable external-cavity laser grown by metal-organic chemical vapor deposition

We demonstrate high-performance broadband tunable external-cavity lasers(ECLs) with the metal-organic chemical vapor deposition(MOCVD) grown In As/In P quantum dots(QDs) structures. Without cavity facet coatings, the 3-d B spectral bandwidth of the Fabry–Perot(FP) laser is approximately 10.8 nm, while the tuning bandwidth of ECLs is 45 nm.Combined with the anti-reflection(AR)/high-reflection(HR) facet coating, a 92 nm bandwidth tuning range has been obtained with the wavelength covering from 1414 nm to 1506 nm. In most of the tuning range, the threshold current density is lower than 1.5 k A/cm2. The maximum output power of 6.5 m W was achieved under a 500 m A injection current.All achievements mentioned above were obtained under continuous-wave(CW) mode at room temperature(RT).

A Broadband Pulsed External-Cavity Quantum Cascade Laser Operating near 6.9μm

We report an external cavity quantum cascade laser （EC-QCL） operating near 6.9μm using the Littman Metcalf configuration. The EC-QCL works in a pulsed mode and can be tuned continuously from 1340 to 1640cm^-1 by only tilting the tuning mirror. The fine tuning ability of the EC-QCL is demonstrated by measuring the absorption spectrum of water in the ambient air with a lock-in amplifier.

High power external-cavity surface-emitting laser with front and end pump

High power optically pumped vertical-external-cavity surface-emitting lasers with front and end pump are re- ported. The gain chip consists of 15 repeats of In0.26GaAs/GaAsP0.02 multiple quantum wells and 30 pairs of Alo.2GaAs/Alo.98GaAs distributed Bragg reflectors. The maximum output power of 3 W, optical-to-optical conversion efficiency of 22.4%, and slope efficiency of 29.8% are obtained with 5-℃ heatsink temperature under the front pump, while the maximum output power of 1.1 W, optical-to-optical conversion efficiency of 23.2%, and slope efficiency of 30.8% are reached with 5-℃ heatsink temperature under the end pump. Influences of thermal effects on the output power of the laser with front and end pump are discussed.

Influence of laser linewidth on external-cavity frequency doubling efficiency of a 1.56 μm master oscillator fiber power amplifier

By using an external-cavity frequency-doubling master oscillator fiber power amplifier （MOPA）, a 700 mW continuous-wave single-frequency laser source at 780 nm is produced. It is shown that the frequency doubling efficiency is improved when the seed diode laser is optically locked to a resonant frequency of a confocal Fabry-Perot （F-P） cavity. This phenomenon can be attributed to the narrowing of the 1.56 μm laser linewidth and explained by our presented theoretical model. The experimental results are found to be in good agreement with the theoretical predictions.

Design and fabrication of a compact, high-performance interference-filter-based external-cavity diode laser for use in the China Space Station

A hertz-linewidth ultra-stable laser(USL), which will be used to detect the clock transition line, in a strontium optical clock will be launched into the China Space Station(CSS) in late 2022. As the core of the USL, an interference-filter-based externalcavity diode laser(IF-ECDL) was developed. The IF-ECDL has a compact, stable, and environmentally insensitive design.Performances of the IF-ECDL are presented. The developed IF-ECDL can pass the aerospace environmental tests, indicating that the IF-ECDL can be suitable for space missions in the CSS.

External-Cavity Tunable Laser Using MEMS Technology

This paper introduces a tunable external-cavity diode laser using a MEMS vertical mirror fabricated on a silicon-on-insulator (SOI) wafer. This laser has the merits of simple alignment process, easy integration/packaging, and potentially large wavelength tuning range.

Wide and fast-frequency tuning for a stabilized diode laser

External-cavity diode laser(ECDL)has important applications in many fundamental and applied researches.Here we report a method to fast and widely tune the frequency of a stabilized ECDL.The beat frequency between the ECDL and a frequency-locked reference laser is identified by the voltagecontrolled oscillator contained in a phase detector,whose output voltage is subtracted from the flexibly controlled PC signal to generate an error signal for stabilizing the ECDL.The output frequency of the stabilized ECDL can be shifted at a short characteristic time of∼150µs within a range of∼620 MHz.The wide and fast-frequency tuning achieved by our method is compared with other previous works.We demonstrated the performance of our method by the efficient sub-Doppler cooling of Cs atoms with the temperature as low as 6µK.