Effects of the initiation position on the damage and fracture characteristics of linear-charge blasting in rock

To study the effects of the initiation position on the damage and fracture characteristics of linear-charge blasting, blasting model experiments were conducted in this study using computed tomography scanning and three-dimensional reconstruction methods. The fractal damage theory was used to quantify the crack distribution and damage degree of sandstone specimens after blasting. The results showed that regardless of an inverse or top initiation, due to compression deformation and sliding frictional resistance, the plugging medium of the borehole is effective. The energy of the explosive gas near the top of the borehole is consumed. This affects the effective crushing of rocks near the top of the borehole, where the extent of damage to Sections Ⅰ and Ⅱ is less than that of Sections Ⅲ and Ⅳ. In addition, the analysis revealed that under conditions of top initiation, the reflected tensile damage of the rock at the free face of the top of the borehole and the compression deformation of the plug and friction consume more blasting energy, resulting in lower blasting energy efficiency for top initiation. As a result, the overall damage degree of the specimens in the top-initiation group was significantly smaller than that in the inverse-initiation group. Under conditions of inverse initiation, the blasting energy efficiency is greater, causing the specimen to experience greater damage. Therefore, in the engineering practice of rock tunnel cut blasting, to utilize blasting energy effectively and enhance the effects of rock fragmentation, using the inverse-initiation method is recommended. In addition, in three-dimensional(3D) rock blasting, the bottom of the borehole has obvious end effects under the conditions of inverse initiation, and the crack distribution at the bottom of the borehole is trumpet-shaped. The occurrence of an end effect in the 3D linear-charge blasting model experiment is related to the initiation position and the blocking condition.

Performance of water-coupled charge blasting under different in-situ stresses

Water-coupled charge blasting is a promising technique to efficiently break rock masses.In this study,numerical models of double boreholes with water-coupled charge are established using LS-DYNA and are calibrated by the tests of rock masses subjected to explosion loads to examine its performance.The crack levels of rock mass induced by water-coupled charge blasting and air-coupled charge blasting are first compared.It is found that water-coupled charge blasting is more appropriate to fracture deep rock mass than air-coupled charge blasting.In addition,the effects of rock properties,water-coupled charge coefficients,and borehole connection angles on the performance of water-coupled charge blasting are investigated.The results show that rock properties and water-coupled charge coefficients can greatly influence the crack and fragmentation levels of rock mass induced by water-coupled charge blasting under uniform and non-uniform in-situ stresses.However,changing borehole-connection angles can only affect crack and fragmentation levels of rock mass under non-uniform in-situ stresses but barely affect those under uniform in-situ stresses.A formula is finally proposed by considering the above-mentioned factors to provide the design suggestion of water-coupled charge blasting to fracture rock mass with different in-situ stresses.

Influence of millisecond time,charge length and detonation velocity on blasting vibration

The law of blasting vibration caused by blasting in rock is very complex.Traditional numerical methods cannot well characterize all the influencing factors in the blasting process.The effects of millisecond time,charge length and detonation velocity on the blasting vibration are discussed by analyzing the characteristics of vibration wave generated by finite length cylindrical charge.It is found that in multi-hole millisecond blasting,blasting vibration superimpositions will occur several times within a certain distance from the explosion source due to the propagation velocity difference of P-wave and S-wave generated by a short column charge.These superimpositions will locally enlarge the peak velocity of blasting vibration particle.The magnitude and scope of the enlargement are closely related to the millisecond time.Meanwhile,the particle vibration displacement characteristics of rock under long cylindrical charge is analyzed.The results show that blasting vibration effect would no longer increase when the charge length increases to a certain extent.This indicates that the traditional simple calculation method using the maximum charge weight per delay interval to predict the effect of blasting vibration is unreasonable.Besides,the effect of detonation velocity on blasting vibration is only limited in a certain velocity range.When detonation velocity is greater than a certain value,the detonation velocity almost makes no impact on blasting vibration.

Study on orientation fracture blasting with shaped charge in rock

On the basis of the theories of mechanics of explosive and rock fracture mechanics, the mechanism of crack initiation and its expansion of directional fracture controlled blasting with shaped charges in rock were studied, then the blasting parameters were designed and tested by a model test in laboratory and field experiment. The experimental and test results showed that the energy from blasting is directionally concentrated for the cumulative action. The directional expansion of cracks is satisfactory, the results of the model test and field test suggested that the orientation fracture blasting with shaped charge is a good means of excavating tunnels or cutting rock.

Numerical investigation of effect of eccentric decoupled charge structure on blasting-induced rock damage

Eccentric decoupling blasting is commonly used in underground excavation.Determination of perimeter hole parameters(such as the blasthole diameter,spacing,and burden)based on an eccentric charge structure is vital for achieving an excellent smooth blasting effect.In this paper,the Riedel-Hiermaier-Thoma(RHT)model was employed to study rock mass damage under smooth blasting.Firstly,the parameters of the RHT model were calibrated by using the existing SHPB experiment,which were then verified by the existing blasting experiment results.Secondly,the influence of different charge structures on the blasting effect was investigated using the RHT model.The simulation results indicated that eccentric charge blasting has an obvious pressure eccentricity effect.Finally,to improve the blasting effect,the smooth blasting parameters were optimized based on an eccentric charge structure.The overbreak and underbreak phenomena were effectively controlled,and a good blasting effect was achieved with the optimized blasting parameters.

Numerical investigation on free air blast loads generated from center-initiated cylindrical charges with varied aspect ratio in arbitrary orientation

In current guidelines, the free air blast loads(overpressure and impulse) are determined by spherical charges, although most of ordnance devices are more nearly cylindrical than spherical in geometry. This may result in a great underestimation of blast loads in the near field and lead to an unsafe design.However, there is still a lack of systematic quantitative analysis of the blast loads generated from cylindrical charges. In this study, a numerical model is developed by using the hydrocode AUTODYN to investigate the influences of aspect ratio and orientation on the free air blast loads generated from center-initiated cylindrical charges. This is done by examining the pressure contours, the peak overpressures and impulses for various aspect ratios ranged from 1 to 8 and arbitrary orientation monitored along every azimuth angle with an interval of 5°. To characterize the distribution patterns of blast loads,three regions, i.e., the axial region, the vertex region and the radial region are identified, and the propagation of blast waves in each region is analyzed in detail. The complexity of blast loads of cylindrical charges is found to result from the bridge wave and its interaction with primary waves. Several empirical formulas are presented based on curve-fitting the numerical data, including the orientation where the maximum peak overpressure emerges, the critical scaled distance beyond which the charge shape effect could be neglected and blast loads with varied aspect ratio in arbitrary orientation, all of which are useful for blast-resistant design.

Comparison of dominant frequency attenuation of blasting vibration for different charge structures

Dominant frequency attenuation is a significant concern for frequency-based criteria of blasting vibration control.It is necessary to develop a concise and practical prediction equation describing dominant frequency attenuation.In this paper,a prediction equation of dominant frequency that accounts for primary parameters influencing the dominant frequency was proposed based on theoretical and dimensional analyses.Three blasting experiments were carried out in the Chiwan parking lot for collecting blasting vibration data used to conduct regression analysis of the proposed prediction equation.The fitting equations were further adopted to compare the reliability of three different types of dominant frequencies in the proposed equation and to explore the effects of different charge structures on the dominant frequency attenuation.The apparent frequency proved to be more reliable to express the attenuation law of the dominant frequency.The reliability and superiority of the proposed equation employing the apparent frequency were verified by comparison with the other five prediction equations.The smaller blasthole diameter or decoupling ratio leads to the higher initial value and corresponding faster attenuation of the dominant frequency.The blasthole diameter has a greater influence on the dominant frequency attenuation than the decoupling ratio does.Among the charge structures applied in the experiments,the charge structure with decoupling ratio of 1.5 and blasthole diameter of 48 mm results in the greatest initial value and corresponding fastest attenuation of the dominant frequency.

Influence of maximum decking charge on intensity of blasting vibration

Based on the character of short-time non-stationary random signal, the relationship between the maximum decking charge and energy distribution of blasting vibration signals was investigated by means of the wavelet packet method. Firstly, the characteristics of wavelet transform and wavelet packet analysis were described. Secondly, the blasting vibration signals were analyzed by wavelet packet based on software MATLAB, and the change of energy distribution curve at different frequency bands were obtained. Finally, the law of energy distribution of blasting vibration signals changing with the maximum decking charge was analyzed. The results show that with the increase of decking charge, the ratio of the energy of high frequency to total energy decreases, the dominant frequency hands of blasting vibration signals tend towards low frequency and hlasting vibration does not depend on the maximum decking charge.

Blast performance of layered charges enveloped by aluminum powder/rubber composites in confined spaces

A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.

Numerical simulation of blasting effect with divided charge structure

This paper numerically simulates the stress development and generates a three-dimensional model of the medium-length hole blasting in infinite rock mass for continuous charge and divided charge in blasting by using the large-scale nonlinear dynamic analysis software LS-DYNA and the elastic-plastic model ~*MAT_PLASTIC_KINEMATIC and JWO-EOS.The differences of the decreasing rate in Von Mises effective stress of blasting,element effective stress peak of free surface,bore wall stress and acceleration are investigated.It is shown that divided charge could greatly improve the blasting effect by engineering blasting practice.

Theoretical and numerical simulation investigation of deep hole dispersed charge cut blasting

Drilling and blasting methods have been used as a common driving technique for shallow-hole driving and blasting in rock roadways.With the advent of digital electronic detonators and the need for increased production efciency,the traditional blasting design is no longer suitable for deep hole blasting.In this paper,a disperse charge cut blasting method was proposed to address the issues of low excavation depth and high block rate in deep hole undercut blasting.First,a blasting model was used to illustrate the mechanism of the deep hole dispersive charge cut blasting process.Then,continuous charge and dispersed charge blasting models were developed using the smooth particle hydrodynamics-fnite element method(SPHFEM).The cutting parameters were determined theoretically,and the cutting efciency was introduced to evaluate the cutting efect.The blasting efects of the two charging models were analyzed utilizing the evolution law of rock damage,the number of rock particles thrown,and the cutting efciency.The results show that using a dispersed charge improves the cutting efciency by about 20%and the rock breakage for the deep hole cut blasting compared to the traditional continuous charge.In addition,important parameters such as cutting hole spacing,cutting hole depth and upper charge proportion also have a signifcant impact on the cutting efect.Finally,the deep hole dispersed charge cut blasting technology is combined with the digital electronic detonator through the feld engineering practice.It provides a reference for the subsequent deep hole cutting blasting and the use of electronic detonators in rock roadways.

THE CALCULATION OF INITIAL SHOCK WAVE IN ROCK WITH UNCOUPLING CHARGE BLASTING

According to the structure of explosive charge in rock blasting, a physical model has been set up in this paper. Based on the model, a methodology for calculating initial shock wave of uncoupling charge has been given. The pressure p3 has been calculated when high explosives act on granite, limestone, marble and shaIe respectively. Some important conclusions are also gained by the analysis of results.

Numerical study on the fracturing mechanism of shock wave interactions between two adjacent blast holes in deep rock blasting

With the application of electronic detonators, millisecond blasting is regarded as a signifi cant promising approach to improve the rock fragmentation in deep rock blasting. Thus, it is necessary to investigate the fracturing mechanisms of short-delay blasting. In this work, a rectangle model with two circle boreholes is modeled as a particles assembly based on the discrete element method to simulate the shock wave interactions induced by millisecond blasting. The rectangle model has a size of 12 × 6 m (L × W) and two blast holes have the same diameter of 12 cm. The shock waves are simplifi ed as time-varying forces applied at the particles of walls of the two boreholes. Among a series of numerical tests in this study, the spacing between two adjacent boreholes and delay time of millisecond blasting are considered as two primary variables, and the decoupling charge with a coeffi cient of 1.5 is taken into account in each case. The results show that stress superposition is not a key factor for improving rock fragmentation (tensile stress interactions rather than compressive stress superposition could aff ect the generation of cracks), whereas collision actions from isolated particles or particles with weakened constraints play a crucial role in creating the fracture network. The delay time has an infl uence on causing cracks in rock blasting, however, whether it works heavily depends on the distance between the two holes.

Numerical simulation of the blast wave of a multilayer composite charge

The numerical simulation of a blast wave of a multilayer composite charge is investigated.A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program.Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25-0.5 cm and 1-3 cm.The Euler--fluxcorrected transport solver is found to be suitable for the far-field calculation after mapping.A numerical simulation is conducted to study the formation,propagation,and interaction of the shock wave of the composite charge for different initiation modes.It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge.Additionally,it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation,and the peak pressure of the shock wave exponentially decays,fitting the calculation formula of the peak overpressure attenuation under different initiation modes,which is obtained and verified by experiment.The difference between numerical and experimental results is less than 10%,and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.

Penetration and internal blast behavior of reactive liner enhanced shaped charge against concrete space

Penetration and internal blast behavior of reactive liner enhanced shaped charge against concrete space were investigated through experiments and simulations.The volume of the enclosed concrete space is about 15 m^(3).The reactive liner enhanced shaped charge utilizes reactive copper double-layered liner,which is composed of an inner copper liner and an outer reactive liner,while the reactive material liner is fabricated by PTFE/Al(Polytetrafluoroethylene/Aluminum)powders through cold-pressing and sintering.Static explosion experiments show that,compared with the shaped charge which utilizes copper liner,the penetration cavity diameter and spalling area of concrete by the novel shaped charge were enlarged to 2 times and 4 times,respectively.Meanwhile,the following reactive material had blast effect and produced significant overpressure inside the concrete closed space.Theoretical analysis indicates concrete strength and detonation pressure of reactive material both affect the penetration cavity diameter.To the blast behavior of reactive material inside the concrete space,developing TNT equivalence model and simulated on AUTODYN-3 D for analysis.Simulation results reproduced propagation process of the shock wave in concrete space,and revealed multi-peaks phenomenon of overpressure-time curves.Furthermore,the empirical relationship between the peak overpressure and relative distance for the shock wave of reactive material was proposed.

Novel blast furnace operation process involving charging with low-titanium vanadium–titanium magnetite carbon composite hot briquette

An innovative process of blast furnace （BF） operation involving charging with low-titanium vanadium-titanium magnetite carbon composite hot briquette （LVTM-CCB） was proposed for utilizing LVTM and conserving energy, In this study, the effect of LVTM-CCB charging ratio on the softening, melting, and dripping behaviors of the mixed burden was explored systemically, and the migration of valu- able elements V and Cr was extensively investigated. The results show that with increasing LVTM-CCB charging ratio, the softening inter- val T40 - T4 increases from 146.1℃ to 266.1℃, and the melting interval To - Ts first decreases from 137.2℃ to 129.5℃ and then increases from 129.5℃ to 133.2℃. Moreover, the cohesive zone becomes narrower and then wider, and its location shifts slightly downward. In addi- tion, the recovery ratios of V and Cr in dripped iron first increase and then decrease, reaching maximum values of 14.552% and 28.163%, respectively, when the charging ratio is 25%. A proper LVTM-CCB charging ratio would improve the softening--melting behavior of the mixed burden; however, Ti（C,N） would be generated rapidly in slag when the charging ratio exceeds 25%, which is not favorable for BF op- eration. When considering the comprehensive softening-melting behavior of the mixed burden and the recovery ratios of V and Cr, the rec- ommended LVTM-CCB charging ratio is 20%.

Modeling the blast load induced by a close-in explosion considering cylindrical charge parameters

Structural damage is significantly influenced by the various parameters of a close-in explosion.To establish a close-in blast loading model for cylindrical charges according to these parameters,a series of field experiments and a systematic numerical analysis were conducted.A high-fidelity finite element model developed using AUTODYN was first validated using blast data collected from field tests conducted in this and previous studies.A quantitative analysis was then performed to determine the influence of the charge shape,aspect ratio(length to diameter),orientation,and detonation configuration on the characteristics and distributions of the blast loading(incident peak overpressure and impulse)according to scaled distance.The results revealed that the secondary peak overpressure generated by a cylindrical charge was mainly distributed along the axial direction and was smaller than the overpressure generated by an equivalent spherical charge.The effects of charge shape on the blast loading at 45°and 67.5°in the axial plane could be neglected at scaled distances greater than 2 m/kg^(1/3);the effect of aspect ratios greater than 2 on the peak overpressure in the 90°(radial)direction could be neglected at all scaled distances;and double-end detonation increased the radial blast loading by up to 60%compared to singleend detonation.Finally,an empirical cylindrical charge blast loading model was developed considering the influences of charge aspect ratio,orientation,and detonation configuration.The results obtained in this study can serve as a reference for the design of blast tests using cylindrical charges and aid engineers in the design of blast-resistant structures.

A new method of cut-blasting for vertical shaft excavation and its experimental study

Based on cutting principle and technology development of vertical blasthole cutby stage and deck in vertical shaft excavation, combined with the merits of middle spacecharging and toe space charging, the reinforced cutting effect of central large-diameterblasthole and the method of cutting blast by stage and deck toe space charging for thevertical large-diameter blastholes was put forward and analyzed theoretically.This new cutblasting method is provided with the advantages of high blasthole using ratio, big cavitybulk, low rate of chunk, even lumpiness, and relatively high energy using ratio.The parameterchoices and practical effects of this cutting method were discussed after in situexperiment.It shows that the decked delay time of 75～100 ms is applicable.

Field experiment for blasting crater

A series of single hole blasting crater experiments and a variable distance multi-hole simultaneous blasting experiment was carried in the Yunfu Troilite Mine,according to the Livingston blasting crater theory.We introduce in detail,our methodology of data collection and processing from our experiments.Based on the burying depth of the explosives,the blasting crater volume was fitted by the method of least squares and the characteristic curve of the blasting crater was obtained using the MATLAB soft- ware.From this third degree polynomial,we have derived the optimal burying depth,the critical burying depth and the optimal explosive specific charge of the blasting crater.

Blast wave characteristics of multi-layer composite charge:Theoretical analysis,numerical simulation,and experimental validation

This article investigates the characteristics of shock wave overpressure generated by multi-layer composite charge under different detonation modes.Combining dimensional analysis and the explosion mechanism of the charge,a peak overpressure prediction model for the composite charge under singlepoint detonation and simultaneous detonation was established.The effects of the charge structure and initiation method on the overpressure field characteristics were investigated in AUTODYN simulation.The accuracy of the prediction model and the reliability of the numerical simulation method were subsequently verified in a series of static explosion experiments.The results reveal that the mass of the inner charge was the key factor determining the peak overpressure of the composite charge under single-point detonation.The peak overpressure in the radial direction improved apparently with an increase in the aspect ratio of the charge.The overpressure curves in the axial direction exhibited a multi-peak phenomenon,and the secondary peak overpressure even exceeded the primary peak at distances of 30D and 40D(where D is the charge diameter).The difference in peak overpressure among azimuth angles of 0-90°gradually decreased with an increase in the propagation distance of the shock wave.The coupled effect of the detonation energy of the inner and outer charge under simultaneous detonation improved the overpressure in both radial and axial directions.The difference in peak overpressure obtained from model prediction and experimental measurements was less than 16.4%.