The Ti-Al-Sn-Zr-Cr-Mo-V-Si （Ti-62A） alloy, an alpha-beta alloy with high strength and fracture toughness, is currently used as an advanced structural material in aerospace and non-aerospace applications. Thermo-mech...The Ti-Al-Sn-Zr-Cr-Mo-V-Si （Ti-62A） alloy, an alpha-beta alloy with high strength and fracture toughness, is currently used as an advanced structural material in aerospace and non-aerospace applications. Thermo-mechanical processes can be used to optimize the relationship between its strength and fracture toughness. A Ti-62A alloy bar can be machined through a transus β-forged plus α＋β solution treated and aged specimen with a lamellar alpha microstructure. The effects of heat treatment on the mechanical properties were discussed. Heat treatment provided a practical balance of strength, fracture toughness, and fatigue crack growth resistance. A comparison of the Ti-62A alloy with the Ti-62222S alloy under the same thermo-mechanical processing conditions showed that their properties are at the same level.展开更多
Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. Howev...Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. However, there are few reports about the microstructure characteristics on the strengthening and toughening mechanisms of powder hot isostatic pressed(HIPed) titanium alloys. Therefore, TA15powder was prepared into alloy by HIP approach, which was used to explore the microstructure characteristics at different HIP temperatures and the corresponding tensile properties and fracture toughness. Results show that the fabricated alloy has a “basket-like structure” when the HIP temperature is below 950℃, consisting of lath clusters and surrounding small equiaxed grains belts. When the HIP temperature is higher than 950℃, the microstructure gradually transforms into the Widmanstatten structure, accompanied by a significant increase in grain size. The tensile strength and elongation are reduced from 948 MPa and 17.3% for the 910℃ specimen to 861 MPa and 10% for the 970℃ specimen.The corresponding tensile fracture mode changes from transcrystalline plastic fracture to mixed fracture including intercrystalline cleavage.The fracture toughness of the specimens increases from 82.64 MPa·m^(1/2)for the 910℃ specimen to 140.18 MPa·m^(1/2)for the 970℃ specimen.Specimens below 950℃ tend to form holes due to the prior particle boundaries(PPBs), which is not conducive to toughening. Specimens above 950℃ have high fracture toughness due to the crack deflection, crack branching, and shear plastic deformation of the Widmanstatten structure. This study provides a valid reference for the development of powder HIPed titanium alloy.展开更多
This article studies the phase transformation of the metastable β-Ti-A1-Mo-V-Cr-Zr alloy （Ti-1300） to disclose the morphological reason for its high strength and high fracture toughness. It has been found that its ...This article studies the phase transformation of the metastable β-Ti-A1-Mo-V-Cr-Zr alloy （Ti-1300） to disclose the morphological reason for its high strength and high fracture toughness. It has been found that its ultrahigh strength （ultimate tensile strength exceeds 1 400 MPa） owes mainly to the spheroidization of the α-phase, while the high fracture toughness （exceeds 81 MPa·m^1/2） to the special lath-shaped α-particles. Compared to the needle-shaped second α-articles, the coarser lath-shaped ones remove the stress concentration at the lath tips and consequently benefit improvement of fracture toughness. The article also describes shape evolution of the α-particles during aging thermodynamically and kinetically, and suggests an optimized aging processing to achieve an ideal balance between high strength and high toughness for this alloy.展开更多
The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study an...The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study and develop advanced NC bending technology,it is necessary to understand the bending performance of medium strength TA18(Ti-3Al-2.5V,ASTM Gr.9) titanium alloy tubes during NC bending under different die sets.This paper focuses on the bending performance of medium strength TA18 tubes under different NC bending die sets,including the variations in the stress,strain,wall thickness,cross sectional deformation,and defects.The results show that adding a wiper die to the base die set decreases the radial,hoop,and tangential compressive stress and the tangential compressive strain,and adding a mandrel to the base die set also decreases these stresses,but increases the radial and hoop tensile stress and decreases the hoop compressive strain obviously,and brings about a three-dimensional tensile stress concentration where the mandrel provides support.For the NC bending of medium strength TA18 tubes,the flattening of cross section is more sensitive index than the thinning of wall thickness.Introducing a mandrel can improve the flattening of cross section obviously but it has a little worse effect on the thinning of wall thickness,and adding a wiper die to the base die set can inhibit the occurrence of the inside bulge but worsen the flattening of the cross section remarkably.Considering the above effects of the mandrel and wiper die on bending performance,it is reasonable to apply the die set comprising a bending die,clamp die,and pressure die for tubes with a small diameter and the die set including an appropriate mandrel additionally for tubes with a larger diameter,in order to bend the medium strength TA18 tubes with high quality and at low cost.展开更多
文摘The Ti-Al-Sn-Zr-Cr-Mo-V-Si （Ti-62A） alloy, an alpha-beta alloy with high strength and fracture toughness, is currently used as an advanced structural material in aerospace and non-aerospace applications. Thermo-mechanical processes can be used to optimize the relationship between its strength and fracture toughness. A Ti-62A alloy bar can be machined through a transus β-forged plus α＋β solution treated and aged specimen with a lamellar alpha microstructure. The effects of heat treatment on the mechanical properties were discussed. Heat treatment provided a practical balance of strength, fracture toughness, and fatigue crack growth resistance. A comparison of the Ti-62A alloy with the Ti-62222S alloy under the same thermo-mechanical processing conditions showed that their properties are at the same level.
基金financially supported by the National Natural Science Foundation of China (Nos. 51874037 and 51922004)the Beijing Natural Science Foundation (No. 2212035)+1 种基金the Fundamental Research Funds for the Central Universities (No. FRF-TP-19005C1Z)the National Defense Basic Research Project (No. JCKY2017213004)。
文摘Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. However, there are few reports about the microstructure characteristics on the strengthening and toughening mechanisms of powder hot isostatic pressed(HIPed) titanium alloys. Therefore, TA15powder was prepared into alloy by HIP approach, which was used to explore the microstructure characteristics at different HIP temperatures and the corresponding tensile properties and fracture toughness. Results show that the fabricated alloy has a “basket-like structure” when the HIP temperature is below 950℃, consisting of lath clusters and surrounding small equiaxed grains belts. When the HIP temperature is higher than 950℃, the microstructure gradually transforms into the Widmanstatten structure, accompanied by a significant increase in grain size. The tensile strength and elongation are reduced from 948 MPa and 17.3% for the 910℃ specimen to 861 MPa and 10% for the 970℃ specimen.The corresponding tensile fracture mode changes from transcrystalline plastic fracture to mixed fracture including intercrystalline cleavage.The fracture toughness of the specimens increases from 82.64 MPa·m^(1/2)for the 910℃ specimen to 140.18 MPa·m^(1/2)for the 970℃ specimen.Specimens below 950℃ tend to form holes due to the prior particle boundaries(PPBs), which is not conducive to toughening. Specimens above 950℃ have high fracture toughness due to the crack deflection, crack branching, and shear plastic deformation of the Widmanstatten structure. This study provides a valid reference for the development of powder HIPed titanium alloy.
基金National Basic Research Program of China (2007CB613805)
文摘This article studies the phase transformation of the metastable β-Ti-A1-Mo-V-Cr-Zr alloy （Ti-1300） to disclose the morphological reason for its high strength and high fracture toughness. It has been found that its ultrahigh strength （ultimate tensile strength exceeds 1 400 MPa） owes mainly to the spheroidization of the α-phase, while the high fracture toughness （exceeds 81 MPa·m^1/2） to the special lath-shaped α-particles. Compared to the needle-shaped second α-articles, the coarser lath-shaped ones remove the stress concentration at the lath tips and consequently benefit improvement of fracture toughness. The article also describes shape evolution of the α-particles during aging thermodynamically and kinetically, and suggests an optimized aging processing to achieve an ideal balance between high strength and high toughness for this alloy.
基金supported by the Program for New Century Excellent Talents in University of China (NCET-08-0462)the Fund of the State Key Laboratory of Solidification Processing in NWPU (Grant No. KP200919)the 111 Project of China (B08040)
文摘The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study and develop advanced NC bending technology,it is necessary to understand the bending performance of medium strength TA18(Ti-3Al-2.5V,ASTM Gr.9) titanium alloy tubes during NC bending under different die sets.This paper focuses on the bending performance of medium strength TA18 tubes under different NC bending die sets,including the variations in the stress,strain,wall thickness,cross sectional deformation,and defects.The results show that adding a wiper die to the base die set decreases the radial,hoop,and tangential compressive stress and the tangential compressive strain,and adding a mandrel to the base die set also decreases these stresses,but increases the radial and hoop tensile stress and decreases the hoop compressive strain obviously,and brings about a three-dimensional tensile stress concentration where the mandrel provides support.For the NC bending of medium strength TA18 tubes,the flattening of cross section is more sensitive index than the thinning of wall thickness.Introducing a mandrel can improve the flattening of cross section obviously but it has a little worse effect on the thinning of wall thickness,and adding a wiper die to the base die set can inhibit the occurrence of the inside bulge but worsen the flattening of the cross section remarkably.Considering the above effects of the mandrel and wiper die on bending performance,it is reasonable to apply the die set comprising a bending die,clamp die,and pressure die for tubes with a small diameter and the die set including an appropriate mandrel additionally for tubes with a larger diameter,in order to bend the medium strength TA18 tubes with high quality and at low cost.
