In solid backfill mining without gangue removal, the gangue is separated directly underground and backfilled into goaf. This necessitates the underground construction of an extra-large section chamber for separation e...In solid backfill mining without gangue removal, the gangue is separated directly underground and backfilled into goaf. This necessitates the underground construction of an extra-large section chamber for separation equipments. For the construction of an extra-large section chamber in the Tangshan mine, we proposed an active support through a combination of bolting, anchor cables, lining, and a reinforced chamber floor by inverted arch pouring. ABAQUS software was used to analyze the surrounding rock deformation and the plastic zone development of the chamber under different excavation schemes.The best excavation scheme was determined, and the effectiveness of the combined supports was verified. In practice, the engineering installation showed good overall control of the movement of the surrounding rock, with roof-to-floor and side-to-side convergences of 154.6 and 77.5 mm, respectively,which meets the requirements for underground coal gangue separation.展开更多
The microstructure and room-temperature tensile properties of Ti14,a new α＋Ti2Cu alloy,were investigated after conventional forging at 950°C and semi-solid forging at 1000 and 1050°C,respectively.Results s...The microstructure and room-temperature tensile properties of Ti14,a new α＋Ti2Cu alloy,were investigated after conventional forging at 950°C and semi-solid forging at 1000 and 1050°C,respectively.Results show that coarse grains and grain boundaries are obtained in the semi-solid alloys.The coarse grain boundaries are attributed to Ti2Cu phase precipitations occurred on the grain boundaries during the solidification.It is found that more Ti2Cu phase precipitates on the grain boundaries at a higher semi-solid forging temperature,which forms precipitated zones and coarsens the grain boundaries.Tensile tests exhibit high strength and low ductility for the semi-solid forged alloys,especially after forging at 1000°C.Fracture analysis reveals the evidence of ductile failure mechanisms for the conventional forged alloy and cleavage fracture mechanisms for the alloy after semi-solid forging at 1050°C.展开更多
基金supported by the National Natural Science Foundation of China (No. 51304206)the Project of National Scientific and Technical Supporting Programs Foundation of China (No. 2012BAB13B03)the Program for New Century Excellent Talents in University of Ministry of Education of China (No. NCET-11-0728)
文摘In solid backfill mining without gangue removal, the gangue is separated directly underground and backfilled into goaf. This necessitates the underground construction of an extra-large section chamber for separation equipments. For the construction of an extra-large section chamber in the Tangshan mine, we proposed an active support through a combination of bolting, anchor cables, lining, and a reinforced chamber floor by inverted arch pouring. ABAQUS software was used to analyze the surrounding rock deformation and the plastic zone development of the chamber under different excavation schemes.The best excavation scheme was determined, and the effectiveness of the combined supports was verified. In practice, the engineering installation showed good overall control of the movement of the surrounding rock, with roof-to-floor and side-to-side convergences of 154.6 and 77.5 mm, respectively,which meets the requirements for underground coal gangue separation.
基金supported by the Major State Basic Research and Development Program of China (No.2007CB613807)the Special Fund for Basic Scientific Research of Central Colleges, Chan'an University (No.CHD2010JC115)
文摘The microstructure and room-temperature tensile properties of Ti14,a new α＋Ti2Cu alloy,were investigated after conventional forging at 950°C and semi-solid forging at 1000 and 1050°C,respectively.Results show that coarse grains and grain boundaries are obtained in the semi-solid alloys.The coarse grain boundaries are attributed to Ti2Cu phase precipitations occurred on the grain boundaries during the solidification.It is found that more Ti2Cu phase precipitates on the grain boundaries at a higher semi-solid forging temperature,which forms precipitated zones and coarsens the grain boundaries.Tensile tests exhibit high strength and low ductility for the semi-solid forged alloys,especially after forging at 1000°C.Fracture analysis reveals the evidence of ductile failure mechanisms for the conventional forged alloy and cleavage fracture mechanisms for the alloy after semi-solid forging at 1050°C.
