SCADA Data-Based Support Vector Machine for False Alarm Identification for Wind Turbine Management

Maintenance operations have a critical influence on power gen-eration by wind turbines(WT).Advanced algorithms must analyze large volume of data from condition monitoring systems(CMS)to determine the actual working conditions and avoid false alarms.This paper proposes different support vector machine(SVM)algorithms for the prediction and detection of false alarms.K-Fold cross-validation(CV)is applied to evaluate the classification reliability of these algorithms.Supervisory Control and Data Acquisition(SCADA)data from an operating WT are applied to test the proposed approach.The results from the quadratic SVM showed an accuracy rate of 98.6%.Misclassifications from the confusion matrix,alarm log and maintenance records are analyzed to obtain quantitative information and determine if it is a false alarm.The classifier reduces the number of false alarms called misclassifications by 25%.These results demonstrate that the proposed approach presents high reliability and accuracy in false alarm identification.

Adaptive detection of range-spread targets in homogeneous and partially homogeneous clutter plus subspace interference

Adaptive detection of range-spread targets is considered in the presence of subspace interference plus Gaussian clutter with unknown covariance matrix.The target signal and interference are supposed to lie in two linearly independent subspaces with deterministic but unknown coordinates.Relying on the two-step criteria,two adaptive detectors based on Gradient tests are proposed,in homogeneous and partially homogeneous clutter plus subspace interference,respectively.Both of the proposed detectors exhibit theoretically constant false alarm rate property against unknown clutter covariance matrix as well as the power level.Numerical results show that,the proposed detectors have better performance than their existing counterparts,especially for mismatches in the signal steering vectors.

Analysis of the False Alarm Fault in Antenna-servo System of Weather Radar

A false alarm fault frequently appeared in antenna-servo system of the CINRAD/SA weather radar of Shanwei in the second half of 2011, so possible reasons for the false alarm fault were listed firstly using method of exhaustion, and then the main reason was determined using exclusive method. That is, the fault was closely related to the signal transmission channel from the antenna mount to servo system in RDA cabinet. After ex- amining questionable nodes in the transmission channels of the alarm signal, we found that the false alarm fault might result from the interference of a burr in the temperature sensing circuit of the elevation motor. In actual operation, a filter capacitor was connected with the corresponding pin in the upper optical board to screen the interference of a burr, thereby successfully eliminating the false alarm fault in antenna-servo system of the CIN- RAD/SA radar of Shanwei.

Support-Vector-Machine-Based False Alarm Filter of Mechatronic Built-in Test

Diagnosing intermittent fault is an important approach to reduce built-in test（BIT） false alarms. Aiming at solving the shortcoming of the present diagnostic method of intermittent fault, and according to the merit of support vector machines （ SVM） which can be trained with a small-sample, an SVM-based diagnostic model of 3 states that include OK state, intermittent state and faulty state is presented. With the features based on the reflection coefficients of an alarm rate （ AR ） model extracted from small vibration samples, these models are trained to diagnose intermittent faults. The experimental results show that this method can diagnose multiple intermittent faults accurately with small training samples and BIT false alarms are reduced.

False Alarm Attack and Protection of Smoke Detector

Carbon monoxide can cause serious illness or even death if the functionality of smoke alarms fails in the residential home and, in fact, more than 350 persons die every year due to the leak of carbon monoxide. However, vulnerabilities and threats to smoke/CO alarms have not been well-studied. In this paper, through interconnect, a power replay attack has been studied in order to trigger a false alarm. The experimental results demonstrate the smoke alarm can be manipulated. This paper also concentrates on providing a sequence of security methods to defend the smoke alarm system. In future, how to protect smart detectors against attacks will be studied as this can force them to leave high-quality mode of operations.

Modeling Target Detection and Performance Analysis of Electronic Countermeasures for Phased Radar

Interference is a key factor in radar return misdetection.Strong interference might make it difficult to detect the signal or targets.When interference occurs in the sidelobes of the antenna pattern,Sidelobe Cancellation(SLC)and Sidelobe Blanking are two unique solutions to solve this problem(SLB).Aside from this approach,the probability of false alert and likelihood of detection are the most essential parameters in radar.The chance of a false alarm for any radar system should be minimal,and as a result,the probability of detection should be high.There are several interference cancellation strategies in the literature that are used to sustain consistent false alarms regardless of the clutter environment.With the necessity for interference cancellation methods and the constant false alarm rate(CFAR),the Maisel SLC algorithm has been modified to create a new algorithm for recognizing targets in the presence of severe interference.The received radar returns and interference are simulated as non-stationary in this approach,and side-lobe interference is cancelled using an adaptive algorithm.By comparing the performance of adaptive algorithms,simulation results are shown.In a severe clutter situation,the simulation results demonstrate a considerable increase in target recognition and signal to noise ratio when compared to the previous technique.

Multi-Attack Intrusion Detection System for Software-Defined Internet of Things Network

Currently,the Internet of Things(IoT)is revolutionizing communi-cation technology by facilitating the sharing of information between different physical devices connected to a network.To improve control,customization,flexibility,and reduce network maintenance costs,a new Software-Defined Network(SDN)technology must be used in this infrastructure.Despite the various advantages of combining SDN and IoT,this environment is more vulnerable to various attacks due to the centralization of control.Most methods to ensure IoT security are designed to detect Distributed Denial-of-Service(DDoS)attacks,but they often lack mechanisms to mitigate their severity.This paper proposes a Multi-Attack Intrusion Detection System(MAIDS)for Software-Defined IoT Networks(SDN-IoT).The proposed scheme uses two machine-learning algorithms to improve detection efficiency and provide a mechanism to prevent false alarms.First,a comparative analysis of the most commonly used machine-learning algorithms to secure the SDN was performed on two datasets:the Network Security Laboratory Knowledge Discovery in Databases(NSL-KDD)and the Canadian Institute for Cyberse-curity Intrusion Detection Systems(CICIDS2017),to select the most suitable algorithms for the proposed scheme and for securing SDN-IoT systems.The algorithms evaluated include Extreme Gradient Boosting(XGBoost),K-Nearest Neighbor(KNN),Random Forest(RF),Support Vector Machine(SVM),and Logistic Regression(LR).Second,an algorithm for selecting the best dataset for machine learning in Intrusion Detection Systems(IDS)was developed to enable effective comparison between the datasets used in the development of the security scheme.The results showed that XGBoost and RF are the best algorithms to ensure the security of SDN-IoT and to be applied in the proposed security system,with average accuracies of 99.88%and 99.89%,respectively.Furthermore,the proposed security scheme reduced the false alarm rate by 33.23%,which is a significant improvement over prevalent schemes.Finally,tests of the algorithm for dataset selection showed that the rates of false positives and false negatives were reduced when the XGBoost and RF algorithms were trained on the CICIDS2017 dataset,making it the best for IDS compared to the NSL-KDD dataset.

A New Two-Stage Tunable Space-Time Adaptive Detector

In order to improve the rejection capability of mismatched interferer signals,a new two-stage detector is proposed under homogeneous scenarios with unknown covariance matrix,which is obtained by cascading the adaptive matched filter(AMF)detector and the enhanced RAO(EnRAO)detector.The new detector has constant false alarm performance,and the closed-form expression of probability of false alarm and probability of detection is derived.The performance of the new detector is assessed,and analyzed in comparison with other detectors.The results show that,the proposed detector can provide enhanced rejection capability in the case of mismatch,but the performance of the detector is slightly lost under the condition of matching.

Semisupervised heterogeneous ensemble for ship target discrimination in synthetic aperture radar images

Ship detection using synthetic aperture radar(SAR)plays an important role in marine applications.The existing methods are capable of quickly obtaining many candidate targets,but numerous non-ship objects may be wrongly detected in complex backgrounds.These non-ship false alarms can be excluded by training discriminators,and the desired accuracy is obtained with enough verified samples.However,the reliable verification of targets in large-scene SAR images still inevitably requires manual interpretation,which is difficult and time consuming.To address this issue,a semisupervised heterogeneous ensemble ship target discrimination method based on a tri-training scheme is proposed to take advantage of the plentiful candidate targets.Specifically,various features commonly used in SAR image target discrimination are extracted,and several acknowledged classification models and their classic variants are investigated.Multiple discriminators are constructed by dividing these features into different groups and pairing them with each model.Then,the performance of all the discriminators is tested,and better discriminators are selected for implementing the semisupervised training process.These strategies enhance the diversity and reliability of the discriminators,and their heterogeneous ensemble makes more correct judgments on candidate targets,which facilitates further positive training.Experimental results demonstrate that the proposed method outperforms traditional tritraining.

DCT domain filtering method for multi-antenna code acquisition

For global navigation satellite system （GNSS） signals in Gaussian and Rayleigh fading channel, a novel signal detection algorithm is proposed. Under the low frequency uncertainty case, after performing discrete cosine transform （DCT） to the outputs of the partial matched filter （PMF） for every antenna, the high order com- ponents in the transforming domain will be filtered, then the equalgain （EG） combination for the inverse discrete cosine transform （IDCT） reconstructed signal would be done subsequently. Thus, due to the different frequency distribution characteristics between the noise and signals, after EG combination, the energy of signals has almost no loss and the noise energy is greatly reduced. The theoretical analysis and simulation results show that the detection algorithm can effectively improve the signal-to-noise ratio of the captured signal and increase the probability of detection under the same false alarm probability. In addition, it should be pointed out that this method can also be applied to Rayleigh fading channels with moving antenna.

Switching variability index based multiple strategy CFAR detector

A switching variability index （SVl） constant false alarm rate （CFAR） detector is proposed for improving the detection performance of VI-CFAR detectors in multiple targets backgrounds. When the presence of non-homogeneity in CFAR reference windows is indicated by a VI-CFAR detector, a switching- CFAR detector is introduced to optimize the performance of the VI-CFAR detector in homogeneous, multiple targets and clutter edge backgrounds. The structure and parameters selection method of the SVI-CFAR detector is presented. Comparisons with classic CFAR detectors and recently proposed detectors are also given. Theoretical analysis and simulation results show that SVICFAR detector maintains the good performance of the VI-CFAR detector in homogeneous and clutter edge backgrounds, while greatly improving the capacity of anti-multi targets.

New CFAR target detector for SAR images based on kernel density estimation and mean square error distance

A new constant false alarm rate （CFAR） target detector for synthetic aperture radar （SAR） images is developed. For each pixel under test, both the local probability density function （PDF） of the pixel and the clutter PDF in the reference window are estimated by the non-parametric density estimation. The target detector is defined as the mean square error （MSE） distance between the two PDFs. The CFAR detection in SAR images having multiplicative noise is achieved by adaptive kernel bandwidth proportional to the clutter level. In addition, for obtaining a threshold with respect to a given probability of false alarm （PFA）, an unsupervised null distribution fitting method with outlier rejection is proposed. The effectiveness of the proposed target detector is demonstrated by the experiment result using the RADATSAT-2 SAR image.

Adaptive coherence estimator based on the Krylov subspace technique for airborne radar

A novel adaptive detector for airborne radar space-time adaptive detection （STAD） in partially homogeneous environments is proposed. The novel detector combines the numerically stable Krylov subspace technique and diagonal loading technique, and it uses the framework of the adaptive coherence estimator （ACE）. It can effectively detect a target with low sample support. Compared with its natural competitors, the novel detector has higher proba- bility of detection （PD）, especially when the number of the training data is low. Moreover, it is shown to be practically constant false alarm rate （CFAR）.

Research on data diagnosis method of acoustic array sensor device based on spectrogram

Acoustic array sensor device for partial discharge detection is widely used in power equipment inspection with the advantages of non-contact and precise positioning compared with partial discharge detection methods such as ultrasonic method and pulse current method.However,due to the sensitivity of the acoustic array sensor and the influence of the equipment operation site interference,the acoustic array sensor device for partial discharge type diagnosis by phase resolved partial discharge(PRPD)map might occasionally presents incorrect results,thus affecting the power equipment operation and maintenance strategy.The acoustic array sensor detection device for power equipment developed in this paper applies the array design model of equal-area multi-arm spiral with machine learning fast fourier transform clean(FFT-CLEAN)sound source localization identification algorithm to avoid the interference factors in the noise acquisition system using a single microphone and conventional beam forming algorithm,improves the spatial resolution of the acoustic array sensor device,and proposes an acoustic array sensor device based on the acoustic spectrogram.The analysis and diagnosis method of discharge type of acoustic array sensor device can effectively reduce the system misjudgment caused by factors such as the resolution of the acoustic imaging device and the time domain pulse of the digital signal,and reduce the false alarm rate of the acoustic array sensor device.The proposed method is tested by selecting power cables as the object,and its effectiveness is proved by laboratory verification and field verification.

Distribution-based CFAR detectors in SAR images

As traditional two-parameter constant false alarm rate （CFAR） target detec-tion algorithms in SAR images ignore target distribution, their performances are not the best or near best. As the resolution of SAR images increases, small targets present more pixels in SAR images. So the target distribution is of much significance. Distribution-based CFAR detection algorithm is presented. We unite the pixels around the test cell, and estimate the distribution of test cell by them. Generalized Likelihood Ratio Test （GLRT） is used to deduce the detectors. The performance of the distribution-based CFAR （DBCFAR） detectors is analyzed theoretically. False alarms of DBCFAR detection are fewer than those of CFAR at the same detection rate. Finally experiments are done and the results show the performance of DBCFAR is out of conventional CFAR. False alarms of DBCFAR detection are concentrated while those of CFAR detection are dispersive.

New acquisition decision algorithm for multiple access interference suppression in DSSS system

For decreasing the multiple access interference of weaker signal acquisition in direct sequence spread spectrum（DSSS） systems,a new single decision algorithm is presented.The maximum value of correlation results is conventionally detected.However,there may be not only one strong peak among correlation results when the cross-correlation noise is strong enough to affect the correlation results.The proposed algorithm decreases the false alarm probability through the decision of the ratio of the maximum value and the second maximum value of the correlation results.Theoretical analysis and simulation results indicate that the proposed algorithm effectively suppresses the acquisition problem of multiple access interference in DSSS system.

New Acquisition Algorithm for Direct Sequence Spread Spectrum Signals

Aiming at improving acquisition performance for direct sequence spread spectrum （DSSS） signals, a new acquisition algorithm based on fast Fourier transform （FFT） is proposed. The code phases are parallel searched throughout the Doppler frequency domain. Since the influence of Doppler frequency errors on peak-to- average ratios of correlation power shows a pattern similar to the sinc function, it is our belief that by judging on peak-to-average ratios for different Doppler frequency errors false alarm probabilities should be lowered. Analyses have supported the underlying principle of this new algorithm. Simulation results have also indicated that the new algorithm can effectively improve the acquisition performance for DSSS signals.

Novel clutter map CFAR algorithm with amplitude limiter

The traditional clutter map constant false alarm rate (CM-CFAR) detector is affected by interference and self-masking[1] which will cause the low probability of detection. To solve these problems, a novel algorithm named clutter map CFAR with amplitude limiter (ALCM-CFAR) is proposed, in which the amplitude of the input signal is limited by a filter. The simulation results prove the effectiveness of ALCM-CFAR algorithm.

Robust and Low-Complexity Synchronization for Energy Detection UWB Receiver

A simple method using aided sliding rectangular windows for synchronization in energy detector （ED） receiver is proposed for impulse-based ultra wideband radios （IR-UWB） under binary pulse position modulation （PPM）, therefore grants an attractive solution for gaining low complexity while the accompanying performance loss in terms of UWB signal reception is comparatively low. Also, a method is developed to sup- press noise through accumulation of integrated results before synchronization point is reached. This proposed method can effectively reduce the impact of one of the major performance-degrading factors in ED receivers, i. e., noise caused by heightened noise floor due to large bandwidth product. Our theoretic work on this im- proved synchronization performance and relevant simulations are conducted on IEEE 802.15.4a channel mod- els, and results show that the proposed design scheme can effectively decrease both the probability of false alarm and probability of missed detection.

Enhanced spectrum sensing using a combination of energy detector,matched filter and cyclic prefix

In this paper,we propose a sensing scheme based on energy detection,matched filter and cyclic prefix.Both Equal Gain Combining(EGC)and optimal combination of the aforementioned detectors are investigated in cooperative and non-cooperative spectrum sensing scenarios.In packet transmission systems such as OFDM(Orthogonal Frequency Division Multiple access)systems,the proposed scheme takes advantage of utilizing more samples than individual detectors,i.e.,cyclic prefix,training or pilot samples,and data payload samples.The proposed combine-sensing scheme offers higher detection probability and lower false alarm probability,as compared with the performance of individual detectors over the same frame duration.Simulation results are congruent with the theoretical curves and confirm the validity of our derivations.